Professional Documents
Culture Documents
General Part
Trade name of the construction product Injection System Hilti HIT-HY 200-R V3
This European Technical Assessment 44 pages including 3 annexes which form an integral part
contains of this assessment
Z101981.21 8.06.01-225/21
European Technical Assessment
ETA-19/0601 Page 2 of 44 | 2 December 2021
English translation prepared by DIBt
The European Technical Assessment is issued by the Technical Assessment Body in its official language.
Translations of this European Technical Assessment in other languages shall fully correspond to the
original issued document and shall be identified as such.
Communication of this European Technical Assessment, including transmission by electronic means,
shall be in full. However, partial reproduction may only be made with the written consent of the issuing
Technical Assessment Body. Any partial reproduction shall be identified as such.
This European Technical Assessment may be withdrawn by the issuing Technical Assessment Body, in
particular pursuant to information by the Commission in accordance with Article 25(3) of Regulation
(EU) No 305/2011.
Z101981.21 8.06.01-225/21
European Technical Assessment
ETA-19/0601 Page 3 of 44 | 2 December 2021
English translation prepared by DIBt
Specific part
The injection system Hilti HIT-HY 200-R V3 is a bonded fastener consisting of a foil pack with
injection mortar Hilti HIT-HY 200-R V3 and a steel element according to Annex A.
The steel element is placed into a drilled hole filled with injection mortar and is anchored via the
bond between metal part, injection mortar and concrete.
The product description is given in Annex A.
The performances given in Section 3 are only valid if the fastener is used in compliance with the
specifications and conditions given in Annex B.
The verifications and assessment methods on which this European Technical Assessment is
based lead to the assumption of a working life of the anchor of at least 50 and/or 100 years. The
indications given on the working life cannot be interpreted as a guarantee given by the
producer, but are to be regarded only as a means for choosing the right products in relation to
the expected economically reasonable working life of the works.
3 Performance of the product and references to the methods used for its assessment
Z101981.21 8.06.01-225/21
European Technical Assessment
ETA-19/0601 Page 4 of 44 | 2 December 2021
English translation prepared by DIBt
In accordance with the European Assessment Document EAD 330499-01-0601 the applicable
European legal act is: [96/582/EC].
The system to be applied is: 1
5 Technical details necessary for the implementation of the AVCP system, as provided for
in the applicable European Assessment Document
Technical details necessary for the implementation of the AVCP system are laid down in the
control plan deposited at Deutsches Institut für Bautechnik.
The following standards and documents are referred to in this European Technical Assessment:
Z101981.21 8.06.01-225/21
Page 5 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Installed condition
Figure A1:
Threaded rod, HAS-U-…, HIT-V-… and AM 8.8
Figure A2:
Threaded rod, HAS-U-…, HIT-V-… and AM 8.8 with Hilti Filling Set
Marking of the
embedment depth
Figure A3:
Internally threaded sleeve HIS-(R)N
Z88969.21 8.06.01-225/21
Page 6 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Installed condition
Figure A4:
Reinforcing bar
Marking of the
embedment depth
Z88969.21 8.06.01-225/21
Page 7 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Marking:
HILTI-HIT
Production number and
production line
Expiry date mm/yyyy
Steel elements
Z88969.21 8.06.01-225/21
Page 8 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Steel elements
Hilti Tension Anchor: HZA M12 to M27 and HZA-R M12 to M24
Hilti Filling Set to fill the annular gap between steel element and fixture
Z88969.21 8.06.01-225/21
Page 9 of European Technical Assessment
ETA-19/0601 of 2 December 2021
AM 8.8 (HDG)
Electroplated zinc coated ≥ 5 μm, (F) hot dip galvanized ≥ 45 μm
Hilti tension anchor
27B Round steel with threaded part: electroplated zinc coated ≥ 5 μm
28B
sleeve HIS-N
30B
Washer
31B Electroplated zinc coated ≥ 5 μm, hot dip galvanized ≥ 45 μm
32B
Filling washer: Electroplated zinc coated ≥ 5 μm, (F) hot dip galvanized ≥ 45 μm
36B
Z88969.21 8.06.01-225/21
Page 10 of European Technical Assessment
ETA-19/0601 of 2 December 2021
For ≤ M24: strength class 70, fuk = 700 N/mm², fyk = 450 N/mm²;
HAS-U A4,
40B
For > M24: strength class 50, fuk = 500 N/mm², fyk = 210 N/mm²;
39B
HIT-V-R
Elongation at fracture (l0=5d) > 12% ductile
For ≤ M24: strength class 70, fuk = 700 N/mm², fyk = 450 N/mm²;
42B
For > M24: strength class 50, fuk = 500 N/mm², fyk = 210 N/mm²;
Threaded rod
Elongation at fracture (l0=5d) > 12% ductile
41B
HZA-R
Rebar: Bars class B according to NDP or NCI of EN 1992-1-1/NA
Internally threaded
Stainless steel 1.4401, 1.4571 EN 10088-1
45B
sleeve HIS-RN
46B
Washer
47B Stainless steel 1.4401, 1.4404, 1.4578, 1.4571, 1.4439, 1.4362 EN 10088-1
48B
For ≤ M24: strength class 70, fuk = 700 N/mm², fyk = 450 N/mm²;
50B
Nut
49B For > M24: strength class 50, fuk = 500 N/mm², fyk = 210 N/mm²;
Stainless steel 1.4401, 1.4404, 1.4578, 1.4571, 1.4439, 1.4362 EN 10088-1
Steel elements made of high corrosion resistant steel
corrosion resistance class (CRC) V according EN 1993-1-4
52B
HIT-V-HCR
Elongation at fracture (l0=5d) > 12% ductile
For ≤ M20: fuk = 800 N/mm², fyk = 640 N/mm²,
For > M20: fuk = 700 N/mm², fyk = 400 N/mm²,
Threaded rod
Elongation at fracture (l0=5d) > 12% ductile
54B
Nut
57B For > M20: fuk = 700 N/mm², fyk = 400 N/mm²,
High corrosion resistant steel 1.4529, 1.4565 EN 10088-1
Z88969.21 8.06.01-225/21
Page 11 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Base material:
Compacted reinforced or unreinforced normal weight concrete without fibres according to EN 206.
Strength classes C20/25 to C50/60 according to EN 206.
Cracked and uncracked concrete.
20B
TE-YD
Hammer drilling
70B
71B
72B
73B
74B
φ 10 to M12 to
Seismic performance category C1 M10 to M30 -
87B 8B
φ 32 M27
85B 86B 89B
M16 to M24,
91B
Threaded rod
(electroplated zinc coated 8.8 and
CRC III, V, Table A1)
Z88969.21 8.06.01-225/21
Page 12 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Design:
Fastenings are designed under the responsibility of an engineer experienced in fastenings and concrete
work.
Verifiable calculation notes and drawings are prepared taking account of the loads to be fastened. The
position of the fastener is indicated on the design drawings (e. g. position of the fastener relative to
reinforcement or to supports, etc.).
The anchorages are designed in accordance with:
EN 1992-4 and EOTA Technical Report TR 055.
Installation:
Use category: dry or wet concrete (not in flooded holes) for all drilling techniques.
Drilling technique:
Hammer drilling,
Hammer drilling with Hilti hollow drill bit TE-CD, TE-YD,
Diamond coring with roughening with Hilti roughening tool TE-YRT.
Installation direction D3: downward, horizontal and upward (e.g. overhead) installation admissible for all
elements.
Fastener installation carried out by appropriately qualified personnel and under the supervision of the
person responsible for technical matters of the site.
Z88969.21 8.06.01-225/21
Page 13 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Table B2: Installation parameters of threaded rod, HAS-U-…, HIT-V-… and AM 8.8
Threaded rod, HAS-U- …, HIT-V-…, AM 8.8
95B M8
96B M10
97B M12
98B M16
9B M20
10B M24
10B M27
102B M30
103B
Diameter of element
104B d
105B [mm]
106B 8
107B 10
108B 12
109B 16
10B 20
1B 24
12B 27
13B 30
14B
60 60 70 80 90 96 108 120
Effective embedment depth
129B 130B 13B 132B 13B 134B 135B 136B
hef = h0 [mm] to to to to to to to to
126B
Minimum spacing
179B smin
180B [mm]
18B 40
182B 50
183B 60
184B 75
185B 90
186B 115
187B 120
18B 140
189B
HAS-U-…
Marking:
Steel grade number and length
identification letter: e.g. 8L
HIT-V-… Marking:
5.8 - l = HIT-V-5.8 M…x l
5.8F - l = HIT-V-5.8F M…x l
8.8 - l = HIT-V-8.8 M…x l
8.8F - l = HIT-V-8.8F M…x l
R-l = HIT-V-R M ...x l
HCR - l = HIT-V-HCR M ...x l
Z88969.21 8.06.01-225/21
Page 14 of European Technical Assessment
ETA-19/0601 of 2 December 2021
member
240B 241B 24B 243B 24B 245B 246B
Minimum spacing
263B smin
264B [mm]
265B 60
26B 75
267B 90
268B 115
269B 130
270B
Marking:
Identifying mark - HILTI and
embossing "HIS-N" (for C-steel)
embossing "HIS-RN" (for stainless steel)
Z88969.21 8.06.01-225/21
Page 15 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Rebar diameter
284B 285B φ [mm]
286B 12
287B 16
28B 20
289B 25
290B
Minimum spacing
31B smin
32B [mm]
3B 65
34B 80
35B 100
36B 130
37B
Rebar diameter
351B 352B φ [mm]
35B 12
354B 16
35B 20
356B 25
357B 28
358B
hnom = h0 [mm] to to to to to
359B
Minimum spacing
403B smin
40B [mm]
405B 65
406B 80
407B 100
408B 130
409B 140
410B
Marking:
embossing “HZA(-R)” M .. / tfix
Z88969.21 8.06.01-225/21
Page 16 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Diameter
431B 432B φ [mm]
43B 8 10 12 14 16 20 25 26 28 30 32
60 60 70 75 80 90 100 104 112 120 128
Effective embedment
437B 438B 439B 40B 41B 42B 43B 4B 45B 46B 47B
hef = h0 [mm] to to to to to to to to to to to
43B
160 200 240 280 320 400 500 520 560 600 640
Nominal diameter of 10 / 12 /
d0 [mm] 141) 161) 18 20 25 32 32 35 37 40
48B 451B 452B
Minimum spacing
468B smin
469B [mm]
470B 40
471B 50
472B 60
473B 70
47B 80
475B 100 125 130 140 150 160
476B 47B 478B 479B 480B 481B
1)
Each of the two given values can be used.
Reinforcing bar
Z88969.21 8.06.01-225/21
Page 17 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Table B7: Maximum working time and minimum curing time HIT-HY 200-R V3
Temperature in the base
496B Maximum working time
497B Minimum curing time
498B
> 0 °C to
513B 514B 5 °C 45 min
516B 517B 4 h
518B 519B
> 5 °C to 10 °C
520B 521B 52B 30 min
523B 524B 2,5 h
52B 526B
> 10 °C to 20 °C
527B 528B 529B 15 min
530B 531B 1,5 h
532B 53B
> 20 °C to 30 °C
534B 53B 536B 9 min
537B 538B 1 h
539B 540B
> 30 °C to 40 °C
541B 542B 543B 6 min
54B 54B 1 h
546B 547B
1)
The minimum foil pack temperature is 0 °C.
Z88969.21 8.06.01-225/21
Page 18 of European Technical Assessment
ETA-19/0601 of 2 December 2021
tion
549B
Threaded
51B Hammer drilling
5B Diamond coring
56B
rod,
Piston
HAS-U-…, HIS-(R)N Rebar HZA(-R) Hollow Roughening Brush
58B
plug
52B 53B 54B 57B
59B 560B
Size
561B size
562B size
563B size
564B d0 [mm] d0 [mm] d0 [mm]
56B 56B 567B d0 [mm]
568B HIT-RB
569B HIT-SZ
570B
M8
571B -
572B
573B φ8 -
574B 10
57B -
576B -
57B -
578B 10
579B -
580B
M10
581B -
582B
583B φ8 / φ10 -
584B 12
58B 12
586B -
587B -
58B 12
589B 12
590B
M12
591B M8
592B
593B φ10 / φ12 -
594B 14
59B 14
596B -
597B -
598B 14
59B 14
60B
-
601B -
602B
603B φ12 M12
604B 16
605B 16
60B -
607B -
608B 16
609B 16
610B
M16
61B M10
612B
613B φ14 -
614B 18
615B 18
61B 18
617B 18
618B 18
619B 18
620B
-
621B -
62B
623B φ16 M16
624B 20
625B 20
62B 20
627B 20
628B 20
629B 20
630B
M20
631B M12
632B -
63B -
634B 22
635B 22
63B 22
637B 22
638B 22
639B 22
640B
-
641B -
642B
643B φ20 M20
64B 25
645B 25
64B 25
647B 25
648B 25
649B 25
650B
M24
651B M16
652B -
653B -
654B 28
65B 28
65B 28
657B 28
658B 28
659B 28
60B
M27
61B -
62B -
63B -
64B 30
65B -
6B 30
67B 30
68B 30
69B 30
670B
-
671B M20
672B
673B φ25 / φ26 M24
674B 32
675B 32
67B 32
67B 32
678B 32
679B 32
680B
M30
681B -
682B
683B φ28 M27
684B 35
685B 35
68B 35
687B 35
68B 35
689B 35
690B
-
691B -
692B
693B φ30 -
694B 37
695B -
69B -
697B -
698B 37
69B 37
70B
-
701B -
702B
703B φ32 -
704B 40
705B -
706B -
70B -
708B 40
709B 40
710B
1)
With vacuum cleaner Hilti VC 20/40/60 (automatic filter cleaning activated) or vacuum cleaner with activated
automatic filter cleaning as well as volumetric flow rate at turbine ≥ 57 l/s, volumetric flow rate at end of hose
≥ 106 m³/h and partial vacuum ≥ 16 kPa.
Cleaning alternatives
Manual Cleaning (MC):
Hilti hand pump for blowing out drill holes with
diameters d0 ≤ 20 mm and
drill hole depths h0 ≤ 10·d.
Z88969.21 8.06.01-225/21
Page 19 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Diamond coring
712B Roughening tool TE-YRT
713B Wear gauge RTG…
714B
d0 [mm]
d0 [mm] size
715B
nominal measured
716B 71B
718B 719B
18
720B 17,9 to 18,2
721B 18
72B 18
723B
20
724B 19,9 to 20,2
725B 20
726B 20
72B
22
728B 21,9 to 22,2
729B 22
730B 22
731B
25
732B 24,9 to 25,2
73B 25
734B 25
735B
28
736B 27,9 to 28,2
73B 28
738B 28
739B
30
740B 29,9 to 30,2
741B 30
742B 30
743B
32
74B 31,9 to 32,2
745B 32
746B 32
74B
35
748B 34,9 to 35,2
749B 35
750B 35
751B
Table B10: Hilti roughening tool TE-YRT – roughening and blowing times
Roughening time
752B Minimum blowing time
753B
troughen tblowing
hef [mm]
754B troughen [sec] = hef [mm] / 10
75B tblowing [sec] = troughen [sec] + 20
756B
0 to 100
75B 10
758B 30
759B
101 to 200
760B 20
761B 40
762B
201 to 300
763B 30
764B 50
765B
301 to 400
76B 40
76B 60
768B
401 to 500
769B 50
70B 70
71B
501 to 600
72B 60
73B 80
74B
Wear gauge
RTG
Z88969.21 8.06.01-225/21
Page 20 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Installation instruction
Hole drilling
2403B
a) Hammer drilling
240B
Drill hole to the required embedment depth with a hammer drill set in rotation-hammer
2406B
Drill hole to the required embedment depth with an appropriately sized Hilti TE-CD or
2408B
TE-YD hollow drill bit attached to Hilti vacuum cleaner VC 20/40/60 or with a vacuum
cleaner according to Table B8, in each case with automatic cleaning of the filter
activated. This drilling system removes the dust and cleans the drill hole during drilling
when used in accordance with the user’s manual. After drilling is completed, proceed to
the “injection preparation” step in the installation instruction.
c) Diamond coring with roughening with Hilti roughening tool TE-YRT:
2409B
Diamond coring is permissible when suitable diamond core drilling machines and the
2410B
Check usability of the roughening tool with the wear gauge RTG.
Roughen the drill hole over the whole length to the required hef.
Roughening time troughen see Table B10.
The Hilti hand pump may be used for blowing out drill holes up to diameters d0 ≤ 20 mm
2416B
Brush 4 times with the specified brush (see Table B8) by inserting the steel brush Hilti
2417B
HIT-RB to the back of the hole (if needed with extension) in a twisting motion and
removing it. The brush must produce natural resistance as it enters the drill hole
(brush Ø ≥ drill hole Ø) - if not the brush is too small and must be replaced with the
proper brush diameter.
Blow out again with the Hilti hand pump at least 4 times until return air stream is free of
2418B
noticeable dust.
Z88969.21 8.06.01-225/21
Page 21 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Compressed air cleaning (CAC) for all drill hole diameters d0 and all drill hole depths h0
2419B
Blow 2 times from the back of the hole (if needed with nozzle extension) over the whole
240B
length with oil-free compressed air (min. 6 bar at 6 m³/h) until return air stream is free of
noticeable dust.
For drill hole diameters ≥ 32 mm the compressor has to supply a minimum air flow of
140 m³/h.
Brush 2 times with the specified brush (see Table B8) by inserting the steel brush Hilti
241B
HIT-RB to the back of the hole (if needed with extension) in a twisting motion and
removing it. The brush must produce natural resistance as it enters the drill hole (brush
Ø ≥ drill hole Ø) - if not the brush is too small and must be replaced with the proper
brush diameter.
Blow again with compressed air 2 times until return air stream is free of noticeable dust.
24B
Cleaning of diamond cored holes with roughening with Hilti roughening tool TE-YRT.
Flush 2 times by inserting a water hose (water-line pressure) to the back of the hole
243B
Brush 2 times with the specified brush (see Table B8) by inserting the steel brush Hilti
24B
HIT-RB to the back of the hole (if needed with extension) in a twisting motion and
removing it. The brush must produce natural resistance as it enters the drill hole (brush
Ø ≥ drill hole Ø) - if not the brush is too small and must be replaced with the proper
brush diameter.
Blow 2 times from the back of the hole (if needed with nozzle extension) over the whole
245B
length with oil-free compressed air (min. 6 bar at 6 m³/h) until return air stream is free of
noticeable dust and water. Remove all water from the drillhole until drillhole is
completely dried before mortar injection (tblowing see Table B10). For drill hole diameters
≥ 32 mm the compressor has to supply a minimum air flow of 140 m³/h.
Z88969.21 8.06.01-225/21
Page 22 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Injection preparation
246B
Tightly attach Hilti mixing nozzle HIT-RE-M to foil pack manifold. Do not modify the
247B
mixing nozzle.
Observe the instruction for use of the dispenser.
Check foil pack holder for proper function. Insert foil pack into foil pack holder and put
holder into dispenser.
The foil pack opens automatically as dispensing is initiated. Depending on the size of
248B
the foil pack, an initial amount of adhesive has to be discarded. Discarded quantities are
2 strokes for 330 ml foil pack,
3 strokes for 500 ml foil pack,
4 strokes for 500 ml foil pack ≤ 5 °C.
The minimum foil pack temperature is 0°C.
Inject adhesive from the back of the drill hole without forming air voids.
249B
Inject the adhesive starting at the back of the hole, slowly withdrawing the mixer with
2430B
After injection is completed, depressurize the dispenser by pressing the release trigger.
2431B
Overhead installation and/or installation with embedment depth hef > 250mm.
243B
For overhead installation the injection is only possible with the aid of extensions and
piston plugs. Assemble HIT-RE-M mixer, extension(s) and appropriately sized piston
plug (see Table B8). Insert piston plug to back of the hole and inject adhesive. During
injection the piston plug will be naturally extruded out of the drill hole by the adhesive
pressure.
Z88969.21 8.06.01-225/21
Page 23 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Before use, verify that the element is dry and free of oil and other contaminants.
243B
Mark and set steel element to the required embedment depth before working time twork
has elapsed. The working time twork is given in Table B7.
For overhead installation use piston plugs and fix embedded parts with e.g. wedges
2435B
(Hilti HIT-OHW).
Loading: After required curing time tcure (see Table B7) the fastening can be loaded.
2436B
The applied installation torque shall not exceed the values max Tinst given in Table B2
to Table B5.
Use Hilti Filling Set with standard nut. Observe the correct orientation of filling washer
2438B
The applied installation torque shall not exceed the values max Tinst given in Table B2
2439B
to Table B5.
Optional:
240B
Installation of lock nut. Tighten with a ¼ to ½ turn. (Not for size M24.)
Fill the annular gap between steel element and fixture with 1-3 strokes of a Hilti
241B
Z88969.21 8.06.01-225/21
Page 24 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Table C1: Essential characteristics for threaded rod, HAS-U-…, HIT-V-... and
AM 8.8 under tension load in concrete
Threaded rod, HAS-U-…, HIT-V-… and AM 8.8
75B M8
76B M10 M12 M16 M20 M24 M27 M30
7B 78B 79B 780B 781B 782B 783B
Installation factor
785B
Hammer drilling
786B γinst
78B [-]
78B 1,0
789B
TE-CD or TE-YD
791B 792B 793B 794B
Steel failure
79B
Spacing
831B scr,N
832B [mm]
83B 3,0 ⋅ hef
834B
Splitting failure
835B
h / hef ≥ 2,0
837B 1,0 ⋅ hef
83B
Edge distance
2,0 > h / hef > 1,3 4,6 ⋅ hef - 1,8 ⋅ h
836B
h / hef ≤ 1,3
841B 2,26 ⋅ hef
842B
Spacing
843B scr,sp
84B [mm]
845B 2·ccr,sp
846B
1) No performance assessed.
2) In absence of national regulations.
Performances Annex C1
Essential characteristics under tension load in concrete
Z88969.21 8.06.01-225/21
Page 25 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Combined pullout and concrete cone failure for a working life of 50 years
856B
Temperature range I:
85B 40 °C / 24 °C τRk,ucr 859B
[N/mm2]
860B 18
Temperature range II:
861B 80 °C / 50 °C τRk,ucr 862B
[N/mm2]
863B 15
Temperature range III: 120 °C / 72 °C τRk,ucr
864B
865B
[N/mm ]
86B
2
13
Characteristic bond resistance in cracked concrete C20/25
867B
Temperature range I:
86B 40 °C / 24 °C τ,cr 869B
[N/mm2]
870B 7,5 8,5 9,0
Temperature range II:
871B 80 °C / 50 °C τRk,cr 872B
[N/mm2]
873B 6,0 7,0 7,5
Temperature range III: 120 °C / 72 °C τRk,cr
874B
875B
[N/mm2]
876B 5,5 6,0 6,5
Influence factors ψ on bond resistance τRk in cracked and uncracked concrete
87B
Temperature range I:
890B 40 °C / 24 °C τRk,ucr,100 [N/mm2]
891B
892B 17
Temperature range II:
893B 80 °C / 50 °C τRk,ucr,100 [N/mm2]
894B
895B 14
Temperature range III: 120 °C / 72 °C τRk,ucr,100 [N/mm2]
896B
897B
89B 12
Characteristic bond resistance in cracked concrete C20/25
89B
Temperature range I:
90B 40 °C / 24 °C τRk,cr,100 [N/mm2]
901B
902B 6,5 8,0
Temperature range II:
903B 80 °C / 50 °C τRk,cr,100 [N/mm2]
904B
905B 5,5 7,0
Temperature range III: 120 °C / 72 °C τRk,cr,100 [N/mm2]
906B
907B
908B 5,0 6,0
Performances Annex C2
Essential characteristics under tension load in concrete
Z88969.21 8.06.01-225/21
Page 26 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Table C2: Essential characteristics for threaded rod, HAS-U-…, HIT-V-… and
AM 8.8 under shear load in concrete
Threaded rod, HAS-U-…, HIT-V-…, AM 8.8
915B M8
916B M10
917B M12
918B M16
91B M20
920B M24
921B M27
92B M30
923B
Partial factor
936B
Ductility factor
954B k7
95B [-]
956B 1,0
957B
Pry-out factor
95B k8
960B [-]
961B 2,0
962B
min (hef;
Effective length of fastener lf [mm] min (hef; 12 ∙ dnom)
968B
8 ∙ dnom; 300)
964B 965B 96B 967B
Performances Annex C3
Essential characteristics under shear load in concrete
Z88969.21 8.06.01-225/21
Page 27 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Installation factor
978B
Hammer drilling
97B γinst
980B [-]
981B 1,0
982B
TE-CD or TE-YD
984B 985B 986B
Steel failure
91B
Partial factor
10B γMs,N2)
10B [-]
102B 1,50
103B
Partial factor
102B γMs,N2)
103B [-]
104B 1,87
105B 2,4
106B
Edge distance
1026B ccr,N
1027B [mm]
1028B 1,5 ⋅ hef
1029B
Spacing
103B scr,N
103B [mm]
1032B 3,0 ⋅ hef
103B
Splitting failure
1034B
h / hef ≥ 2,0
1036B 1,0 ⋅ hef
1037B
Edge distance
2,0 > h / hef > 1,3 4,6 hef - 1,8 h
1035B
h / hef ≤ 1,3
104B 2,26 hef
104B
Spacing
1042B scr,sp
1043B [mm]
104B 2·ccr,sp
1045B
1) No performance assessed.
2)
In absence of national regulations.
Performances Annex C4
Essential characteristics under tension load in concrete
Z88969.21 8.06.01-225/21
Page 28 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Temperature range I:
1069B 40 °C / 24 °C τRk,ucr
107B [N/mm²]
107B 13
1072B
Temperature range I:
1082B 40 °C / 24 °C τRk,cr
1083B [N/mm²]
1084B 7
1085B
Performances Annex C5
Essential characteristics under tension load in concrete
Z88969.21 8.06.01-225/21
Page 29 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Partial factor
120B γMs,V1)
12B [-]
12B 1,25
123B
Partial factor
132B γMs,V1)
13B [-]
134B 1,56
135B 2,0
136B
Ductility factor
137B k7
138B [-]
139B 1,0
140B
Characteristic resistance
M0Rk,s [Nm] 30 60 105 266 519
142B
Characteristic resistance
M0Rk,s [Nm] 26 52 92 233 454
150B
Ductility factor
158B k7
159B [-]
160B 1,0
16B
Pry-out factor
163B k8
164B [-]
165B 2,0
16B
Performances Annex C6
Essential characteristics under shear load in concrete
Z88969.21 8.06.01-225/21
Page 30 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Table C5: Essential characteristics for Hilti tension anchor HZA / HZA-R
under tension load in concrete
Hilti tension anchor HZA, HZA-R M12 M16 M20 M24 M27
For a working life of 50 and 100 years
Installation factor
Hammer drilling γinst [-] 1,0
Hammer drilling with Hilti hollow drill bit
γinst [-] 1,0
TE-CD or TE-YD
Diamond coring with roughening with Hilti
γinst [-] 1)
1,0
roughening tool TE-YRT
Steel failure
Characteristic resistance HZA NRk,s [kN] 46 86 135 194 253
1)
Characteristic resistance HZA-R NRk,s [kN] 62 111 173 248
Partial factor γMs,N2) [-] 1,4
Concrete cone failure
184B
187B 18B
Spacing
193B scr,N [mm] 3,0 ⋅ hef
194B
h / hef ≥ 2,0
197B 1,0⋅hef
198B
Edge distance
2,0 > h / hef > 1,3 4,6⋅hef - 1,8⋅h
196B
Spacing
120B scr,sp
120B [mm]
1203B 2·ccr,sp
1204B
1) No performance assessed.
2) In absence of national regulations.
Performances Annex C7
Essential characteristics under tension load in concrete
Z88969.21 8.06.01-225/21
Page 31 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Performances Annex C8
Essential characteristics under tension load in concrete
Z88969.21 8.06.01-225/21
Page 32 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Table C6: Essential characteristics for Hilti tension anchor HZA, HZA-R
under shear load in concrete
Hilti tension anchor HZA, HZA-R M12
124B M16
125B M20
126B M24
127B M27
For a working life of 50 and 100 years
Steel failure without lever arm
Characteristic resistance HZA V0Rk,s [kN] 23 43 67 97 126
Characteristic resistance HZA-R V0Rk,s [kN] 31 55 86 124 1)
Performances Annex C9
Essential characteristics under shear load in concrete
Z88969.21 8.06.01-225/21
Page 33 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Table C7: Essential characteristics for rebar under tension load in concrete
Rebar
128B
φ 8 φ 10 φ 12 φ 14 φ 16 φ 20 φ 25 φ 26 φ 28 φ 30 φ 32
129B 120B 12B 12B 123B 124B 125B 126B 127B 128B 129B
Installation factor
123B
Hammer drilling
123B γinst [-] 1,0
123B
Steel failure
1238B
Spacing
1268B scr,N
1269B [mm]
1270B 3,0 ⋅ hef
127B
h / hef ≥ 2,0
1274B 1,0⋅hef
1275B
Edge distance
2,0 > h / hef > 1,3 4,6⋅hef - 1,8⋅h
1273B
h / hef ≤ 1,3
1278B 2,26⋅hef
1279B
Spacing
1280B scr,sp
128B [mm]
128B 2 ccr,sp
1283B
1) No performance assessed.
2) fuk according to rebar specification.
3) In absence of national regulations.
Z88969.21 8.06.01-225/21
Page 34 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Diameter of rebar
1296B d
1297B [mm]
1298B 8
129B 10
130B 12
130B 14
1302B 16
130B 20
1304B 25
1305B 26
1306B 28
1307B 30
1308B 32
1309B
Combined pull-out and concrete cone failure for a working life of 50 years
130B
Temperature range I:
132B 40°C/24°C τRk,ucr [N/mm²]
13B 134B 12
135B
1)
Temperature range I: 40°C/24°C τRk,cr [N/mm²]
1326B 1327B 1328B 5
1329B 7
130B
1)
Temperature range II: 80°C/50°C τRk,cr [N/mm²]
132B 13B 134B 4
135B 5,5
136B
1)
Temperature range III: 120°C/72°C τRk,cr [N/mm²]
138B 139B 1340B 3,5
134B 5
1342B
Combined pull-out and concrete cone failure for a working life of 100 years
130B
Temperature range I:
132B 40°C/24°C τRk,ucr [N/mm²]
13B 134B 12
135B
1)
Temperature range I: 40°C/24°C τRk,cr [N/mm²]
1326B 1327B 1328B 5
1329B 7
130B
1)
Temperature range II: 80°C/50°C τRk,cr [N/mm²]
132B 13B 134B 4
135B 5,5
136B
1)
Temperature range III: 120°C/72°C τRk,cr [N/mm²]
138B 139B 1340B 3,5
134B 5
1342B
Z88969.21 8.06.01-225/21
Page 35 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Table C8: Essential characteristics for rebar under shear load in concrete
Rebar
1360B
φ 8 φ 10 φ 12 φ 14 φ 16 φ 20 φ 25 φ 26 φ 28 φ 30 φ 32
136B 1362B 136B 1364B 1365B 136B 1367B 1368B 1369B 1370B 137B
Partial factor
1390B γMs,V 2)
139B [-]
1392B 1,5
139B
Ductility factor
1394B k7
1395B [-]
1396B 1,0
1397B
Characteristic resistance
M0Rk,s [Nm] 33 65 112 178 265 518 1012 1139 1422 1749 2123
1402B
Ductility factor
146B k7
147B [-]
148B 1,0
149B
Pry-out factor
142B k8
142B [-]
1423B 2,0
142B
Z88969.21 8.06.01-225/21
Page 36 of European Technical Assessment
ETA-19/0601 of 2 December 2021
δN0 [mm/(N/mm²)] 0,02 0,03 0,03 0,04 0,06 0,07 0,07 0,08
Displacement
1456B 1457B 1458B 1459B 1460B 146B 1462B 1463B 146B 1465B
δN∞
145B
δN0 [mm/(N/mm²)] 0,03 0,04 0,05 0,06 0,08 0,09 0,10 0,12
Displacement
1478B 1479B 1480B 148B 1482B 1483B 148B 1485B 1486B 1487B
δN∞
147B
δN0 [mm/(N/mm²)] 0,04 0,05 0,06 0,08 0,10 0,12 0,13 0,16
Displacement
150B 150B 1502B 1503B 1504B 150B 1506B 1507B 1508B 1509B
δN∞
149B
δN∞
152B
152B [mm/(N/mm²)]
1526B 0,16
1527B
δN∞
1529B
153B [mm/(N/mm²)]
1534B 0,22
153B
δN∞
1537B
154B [mm/(N/mm²)]
1542B 0,29
1543B
δV0 [mm/kN] 0,06 0,06 0,05 0,04 0,04 0,03 0,03 0,03
Displacement
154B 15B 156B 157B 158B 159B 1560B 156B 1562B 1563B
δV∞
153B
Z88969.21 8.06.01-225/21
Page 37 of European Technical Assessment
ETA-19/0601 of 2 December 2021
δN∞
158B
1589B [mm/(N/mm²)]
1590B 0,06
159B 0,09
1592B 0,11
1593B 0,13
1594B 0,14
159B
δN∞
1597B
1605B [mm/(N/mm²)]
160B 0,07
1607B 0,09
1608B 0,11
1609B 0,13
160B 0,15
16B
δN∞
163B
162B [mm/(N/mm²)]
162B 0,07
1623B 0,09
1624B 0,11
1625B 0,14
162B 0,15
1627B
δN∞
1629B
163B [mm/(N/mm²)]
1634B 0,16
1635B
δN∞
1637B
164B [mm/(N/mm²)]
1642B 0,22
1643B
δN∞
1645B
1649B [mm/(N/mm²)]
1650B 0,29
165B
δV∞
1658B
16B [mm/kN]
167B 0,09
168B 0,08
169B 0,08
1670B 0,06
167B 0,06
1672B
Z88969.21 8.06.01-225/21
Page 38 of European Technical Assessment
ETA-19/0601 of 2 December 2021
δN∞
1680B
168B [mm/(N/mm²)]
1689B 0,06
1690B 0,08
169B 0,13
1692B 0,13
1693B 0,15
1694B
δN∞
169B
1704B [mm/(N/mm²)]
1705B 0,06
1706B 0,09
170B 0,14
1708B 0,14
1709B 0,15
170B
δN∞
172B
1720B [mm/(N/mm²)]
172B 0,07
172B 0,09
1723B 0,14
1724B 0,14
1725B 0,16
1726B
δN∞
1728B
1732B [mm/(N/mm²)]
173B 0,16
1734B
δN∞
1736B
1740B [mm/(N/mm²)]
174B 0,22
1742B
δN∞
174B
1748B [mm/(N/mm²)]
1749B 0,29
1750B
δV0
1758B [mm/kN]
1759B 0,05
1760B 0,04
176B 0,04
1762B 0,03
1763B 0,03
1764B
Displacement
175B
δV∞
1765B [mm/kN]
176B 0,08
176B 0,06
1768B 0,06
1769B 0,05
170B 0,05
17B
Z88969.21 8.06.01-225/21
Page 39 of European Technical Assessment
ETA-19/0601 of 2 December 2021
δN0
1786B [mm/(N/mm²)] 0,02 0,03 0,03 0,04 0,04 0,06 0,07 0,08 0,08 0,09 0,09
178B 178B 1789B 1790B 179B 1792B 1793B 1794B 1795B 1796B 179B 1798B
Displacement
1785B
δN∞
179B [mm/(N/mm²)] 0,04 0,05 0,06 0,07 0,08 0,10 0,13 0,14 0,15 0,16 0,17
180B 180B 1802B 1803B 1804B 1805B 1806B 1807B 180B 1809B 180B 18B
δN0
183B [mm/(N/mm²)] 0,03 0,04 0,05 0,05 0,06 0,08 0,10 0,11 0,11 0,12 0,12
184B 185B 186B 187B 18B 189B 1820B 182B 182B 1823B 1824B 1825B
δN∞
1826B [mm/(N/mm²)] 0,04 0,05 0,06 0,07 0,09 0,11 0,14 0,15 0,15 0,16 0,17
1827B 182B 1829B 1830B 183B 1832B 183B 1834B 1835B 1836B 1837B 183B
δN0
184B [mm/(N/mm²)] 0,04 0,05 0,06 0,07 0,08 0,10 0,12 0,13 0,14 0,15 0,16
1842B 1843B 184B 1845B 1846B 1847B 184B 1849B 1850B 185B 1852B 1853B
Displacement
1840B
δN∞
1854B [mm/(N/mm²)] 0,04 0,05 0,07 0,08 0,09 0,11 0,14 0,15 0,16 0,17 0,18
185B 1856B 1857B 185B 1859B 1860B 186B 1862B 1863B 1864B 1865B 186B
δN0
1869B [mm/(N/mm²)]
1870B 0,11
187B
Displacement
186B
δN∞
1872B [mm/(N/mm²)]
1873B 0,16
1874B
δN0
187B [mm/(N/mm²)]
187B 0,15
1879B
Displacement
1876B
δN∞
180B [mm/(N/mm²)]
18B 0,22
182B
δN0
185B [mm/(N/mm²)]
186B 0,20
187B
Displacement
184B
δN∞
18B [mm/(N/mm²)]
189B 0,29
1890B
δV0
1904B [mm/kN]
1905B 0,06 0,05 0,05 0,04 0,04 0,04 0,03 0,03 0,03 0,03 0,03
1906B 1907B 1908B 190B 190B 19B 192B 193B 194B 195B 196B
Displacement
1903B
δV∞
197B [mm/kN]
198B 0,09 0,08 0,07 0,06 0,06 0,05 0,05 0,05 0,04 0,04 0,04
19B 1920B 192B 192B 1923B 1924B 1925B 1926B 1927B 1928B 192B
Z88969.21 8.06.01-225/21
Page 40 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Table C17: Essential characteristics for threaded rod, HAS-U-…, HIT-V-… and
AM 8.8 under tension load for seismic performance category C1
Threaded rod, HAS-U-…, HIT-V-… and AM 8.8
1930B M10
193B M12
1932B M16
193B M20
1934B M24
1935B M27
1936B M30
1937B
Steel failure
1938B
Temperature range I:
198B 40 °C / 24 °C τRk,C1
1982B [N/mm2]
1983B 5,2
1984B 7,0
1985B
2
Temperature range II:
1986B 80 °C / 50 °C τRk,C1
1987B [N/mm ]
198B 3,9
198B 5,7
190B
2
Temperature range III: 120 °C / 72 °C
19B τRk,C1
192B [N/mm ]
193B 3,5
194B 4,8
195B
Combined pullout and concrete cone failure for a working life of 100 years
196B
Temperature range I:
197B 40 °C / 24 °C τRk,100,C1 [N/mm2]
198B 19B 4,5
20B 6,3
201B
2
Temperature range III: 120 °C / 72 °C
207B τRk,100,C1 [N/mm ]
208B 209B 3,1
201B 4,4
201B
Table C18: Essential characteristics for threaded rod, HAS-U-…, HIT-V-… and
AM 8.8 under shear load for seismic performance category C1
Threaded rod, HAS-U-…, HIT-V-…, AM 8.8
201B M10
2013B M12
2014B M16
2015B M20
2016B M24
2017B M27
2018B M30
2019B
Z88969.21 8.06.01-225/21
Page 41 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Table C19: Essential characteristics for Hilti tension anchor HZA, HZA-R
under tension load for seismic performance category C1
Hilti tension anchor HZA, HZA-R
2105B M12 M16 M20 M24 M27
For a working life of 50 and 100 years
1372B
Steel failure
21B
Diameter of rebar
213B d [mm] 12 16 20 25 28
Characteristic bond resistance in cracked concrete C20/25
214B
Temperature range I:
214B 40°C / 24°C τRk,C1 = τRk,100,C1 [N/mm²] 6,1
Temperature range II:
214B 80°C / 50°C τRk,C1 = τRk,100,C1 [N/mm²] 4,8
Temperature range III:
214B 120°C / 72°C τRk,C1 = τRk,100,C1 [N/mm²] 4,4
Influence factors ψ on bond resistance τRk,C1 and τRk,100,C1 in cracked concrete
1354B
Table C20: Essential characteristics for Hilti tension anchor HZA, HZA-R
under shear load for seismic performance category C1
Hilti tension anchor HZA, HZA-R
2154B M12
215B M16
2156B M20
2157B M24
2158B M27
For a working life of 50 and 100 years
1372B
1)
Characteristic resistance HZA-R
217B VRk,s,C1
2173B [kN]
2174B 22
2175B 39
2176B 60
217B 124
2178B 2179B
Partial factor
2180B γMs,V,C12)
218B [-]
218B 1,5
2183B
1) No performance assessed.
2) In absence of national regulations.
Z88969.21 8.06.01-225/21
Page 42 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Table C21: Essential characteristics for rebar under tension load for seismic
performance category C1
Rebar
2198B φ 10 φ 12 φ 14 φ 16 φ 20 φ 25 φ 26 φ 28 φ 30 φ 32
219B 20B 201B 20B 203B 204B 205B 206B 207B 208B
Steel failure
209B
Characteristic resistance
210B NRk,s,C1
21B [kN]
21B As ∙ fuk1)
Characteristic resistance for rebar
NRk,s,C1 [kN] 43 62 85 111 173 270 292 339 388 442
213B
Diameter of rebar
217B d
218B [mm] 10
219B 20B 12
21B 14
2B 16
23B 20
24B 25
25B 26
26B 28
27B 30
28B 32
29B
Temperature range I:
τRk,C1 = τRk,100,C1 [N/mm²] 4,4 6,1
231B
40°C/24°C
23B 234B 235B
80°C/50°C
238B 239B 240B
120°C/72°C
243B 24B 245B
Table C22: Essential characteristics for rebar under shear loads for seismic
performance category C1
Rebar
246B φ 10 φ 12 φ 14 φ 16 φ 20 φ 25 φ 26 φ 28 φ 30 φ 32
247B 248B 249B 250B 251B 25B 253B 254B 25B 256B
Characteristic resistance
26B VRk,s,C1
263B [kN]
264B 0,35 ∙ As ∙ fuk1)
Characteristic resistance for rebar
VRk,s,C1 [kN] 15 22 29 39 60 95 102 118 135 155
265B
Z88969.21 8.06.01-225/21
Page 43 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Table C23: Essential characteristics for threaded rod, HAS-U-…, HIT-V… and AM 8.8
under tension load for seismic performance category C2
Threaded rod, HAS-U-…, HIT-V-…, AM 8.8
278B M16
279B M20
280B M24
281B
Steel failure
28B
Characteristic resistance
283B
in hammer drilled holes and hammer drilled holes with Hilti hollow drill bit TE-CD or TE-YD
Temperature range I:
28B 40 °C/24 °C τRk,C2 = τRk,100,C2 [N/mm2]
290B 3,9 4,3 3,5
Temperature range II:
291B 80 °C/50 °C τRk,C2 = τRk,100,C2 [N/mm2]
293B 3,3 3,7 2,9
Temperature range III: 120 °C/72 °C
294B τRk,C2 = τRk,100,C2 [N/mm2]
296B 2,8 3,2 2,5
Influence factors ψ on bond resistance τRk,C2 and τRk,100,C2 in cracked concrete
1354B
Table C24: Essential characteristics for threaded rod, HAS-U-…, HIT-V-… and
AM 8.8 under shear load for seismic performance category C2
Threaded rod, HAS-U-…, HIT-V-…, AM 8.8
2307B M16
2308B M20
2309B M24
2310B
Characteristic resistance
HAS-U 8.8, HIT-V 8.8, AM 8.8
230B VRk,s,C2
231B [kN]
23B 46
23B 77
234B 103
235B
Characteristic resistance
HAS-U 8.8, HIT-V 8.8, AM 8.8
237B VRk,s,C2
238B [kN]
239B 40
230B 71
231B 90
23B
Z88969.21 8.06.01-225/21
Page 44 of European Technical Assessment
ETA-19/0601 of 2 December 2021
Table C25: Displacements under tension load for seismic performance category C2
Threaded rod, HAS-U-…, HIT-V-…, AM 8.8…
2345B M16 M20 M24
Displacement DLS,
2349B
Table C26: Displacements under shear load for seismic performance category C2
Threaded rod, HAS-U-…, HIT-V-…, AM 8.8…
2361B M16 M20 M24
Installation with Hilti Filling Set
2365B
Displacement DLS,
δV,C2(DLS) [mm] 1,2 1,4 1,1
HAS-U 8.8, HIT-V 8.8, AM 8.8
Displacement ULS,
δV,C2(ULS) [mm] 3,2 3,8 2,6
HAS-U 8.8, HIT-V 8.8, AM 8.8
Installation without Hilti Filling Set
2378B
Displacement DLS,
HAS-U (-8.8, A4, HCR), HIT-V (-8.8, -R, HCR), AM 8.8,
δV,C2(DLS) [mm] 3,2 2,5 3,5
Threaded rod (electroplated zinc coated 8.8 and
239B
Z88969.21 8.06.01-225/21