Professional Documents
Culture Documents
STD19
STD19
Orientering Introduction
Denna standard omfattar anvisningar för hur krav This standard comprises instructions on how part
på märkning av artiklar ska anges på ritning samt markings are to be shown in technical drawings and
utföras på artiklar. how they are to be made on the parts themselves.
Materialmärkning på artiklar, se STD3871. Material marking on parts, see STD3871.
Märkning av ledningsnät, se STD3222. Markings of cable harnesses, see STD3222.
Märkning av provartiklar, se STD3636. Marking of test parts, see STD3636.
© Scania CV AB, Sweden
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 2 (18)
1 Tillämpning 1 General
Alla krav på märkning ska finnas angivet på rit- All stipulated markings are to be shown on draw-
ning. ing.
Allmänna anvisningar med rekommendationer och General instructions, recommendations, examples
exempel samt policy för identifieringsmärkning av and the policy of marking parts to enable their iden-
artiklar anges i STD14, som endast är avsedd för tification are given in STD14, a document which is
internt bruk. for internal use only.
Här nedan anges de märkningsuppgifter som Information is given below on the various markings
behandlas i denna standard och som i olika om- that are taken up in this standard and that are used
fattning ska tillämpas för identifieringsmärkning for identification purposes on parts.
av artiklar.
– Varumärke - Trademark
– Artikelnummer - Part number
– Datummärkning - Date marking
– Leverantörsnummer - Supplier number
– Chargebeteckning - Charge designation
– Tilläggsmärkning - Supplementary marking
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 3 (18)
Från ett av märkningssymbolens hörn dras en A reference line leads from one of the corners of the
hänvisningslinje till den plats på artikeln där marking symbol to the point on the part where the
märkningen ska utföras. Hänvisningslinjen avslu- marking is to be located. The reference line ends
tas med en pil eller punkt, beroende på i vilken with an arrow or dot depending on the view at which
vy märkningen anges, se figur 1 och 2. the marking point is shown, see figures 1 and 2.
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 4 (18)
Fig. 1 Fig. 2
1
35±3
Fig. 3
Fig.
2
3.3 Märkningens utförande, placering och 3.3 The design and location of the marking
läsriktning and the direction in which it is read
Den märkningsmetod som tillämpas avgör om The method of marking employed determines
märkningen utförs nedsänkt eller upphöjd i mate- whether the marking is to be impressed into or rai-
rialet. All märkning ska utföras med väl täckande sed above the surface. All markings are to be solid
figurationer för symbol, bokstäver och siffror, samt for symbols, letters and numbers and are to make a
ge en jämn och tydlig avbildning i underlaget. Ska clear and even impression on the material. Instruc-
märkningen utföras på ett visst sätt, anges detta tions regarding marking done in a specific way sho-
på ritningen. Är ytan för märkningen skymd, mar- uld be stated on the drawing. If the surface for mark-
keras detta med streckad linje. ing is hidden, it is indicated with a dashed line.
Märkningsdjupet respektive den upphöjda reliefen The depth or height of the marking is determined by
är beroende av den märkningsmetod som an- the method employed and should take into account
vänds och måste anpassas bl.a. efter artikelns the thickness of the material and whether the part is
godstjocklek och om artikeln ska ytbeläggas, så to receive surface treatment. This to ensure that
© Scania CV AB, Sweden
att bästa möjliga tydlighet och läsbarhet uppnås clarity and legibility on the finished part are optimal.
på färdigproducerad artikel.
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 5 (18)
När märkningen ska vara placerad på en bestämd When the marking is to be placed in a specific loca-
plats på artikeln, anges mått till en ruta, se exempel tion on the part, the dimensions to a square indi-
i figur 3. cated, see example in figure 3.
Om märkningstexten ska vara läsbar från ett be- If the marking text is to be read in a specific direc-
stämt håll, anges en pil som markerar textens läs- tion, an arrow points the direction in which it is to be
riktning, se figur 2 och 3. read, see figures 2 and 3.
Här följer några rekommendationer om märkning- The following recommendations apply to the location
ens placering: of the marking:
– Märkningen ska placeras så att den inte blir – The marking should be placed in such a way that
estetiskt störande sedan artikeln monterats. it will not be an eyesore once the part has been
fitted.
– Märkningen ska vara rättvänd och om möjligt – The marking should be the right way up and, if
läsbar efter montering. possible, legible when fitted.
– Märkningen ska om möjligt placeras symmetriskt – The marking should, if possible, be symmetrical
på artikeln. to the part.
– Ett ämnesnummer ska placeras så att det av- – A blank number should be located in such a way
lägsnas i samband med bearbetning. that it will come off during the course of machin-
ing.
– Reservdel som utgör komplett enhet och – A spare part that is a complete unit consisting of
består av flera ingående artiklar, ska på lämpligt several constituent parts should be marked with
sätt märkas med komplettnummer. an assembly number in a suitable location.
4.1 4.3
4.2
4.4
4.5
4.6
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 6 (18)
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 7 (18)
Tabell 1 Märkningsmetoder som medför Table 1 Marking methods which can cause
någon form av deformationer eller deformation or leave marks on the
märken på artikeln part
LAS
Laser Performed with a laser. A contact-free method.
Gnistning Utförs genom elgravering, som är att bränna ett märke med en
elektrisk ljusbåge.
SPA
Sparking Electric engraving, a method which burns a mark into the mate-
rial with an electric arc.
Etsning Utförs elektrokemiskt eller med syra.
ETC
Etching Performed electro-chemically or with acid.
© Scania CV AB, Sweden
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 8 (18)
Tabell 2 Märkningsmetoder som inte defor– Table 2 Marking methods that do not cause
merar eller gör märken på artikeln deformation or leave marks on the
part
LAB
Label A pre-printed self-adhesive label.
HOL
Hologram A label with a three-dimensional image.
© Scania CV AB, Sweden
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 9 (18)
FOR
Forging Performed with a tool when forging.
Vulkning Utförs med en varm stämpel som trycks mot materialet så att ett
avtryck bildas, eller inlagt i formen vid vulkning.
VUL
Vulcanization Performed with a warm stamp which is pressed into the material
to form an impression, or insert in the moulding tool at vulcaniza-
tion.
Tabell 4 Översättning från äldre beteck- Table 4 Changes in designation for older
ningar för märkningsmetoder marking methods
Följande märkningsmetoder har fått nya beteck- The following marking methods have been given
ningar. a new designation.
Äldre beteckning Ny beteckning
Old designation New designation
ETS ETC
GJ CAS
GRV ENG
GRVEL SPA
SM FOR
STÄ PUN
STÄF COL
Alla ingående uppgifter i märkningen ska utföras All characters in the marking are to have the same
med samma teckenhöjd, se avsnitt 6. character height, see section 6.
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 10 (18)
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 11 (18)
Täckande
1A1 Solid
1A
1A2 Konturerat
Outline
Täckande
1B1 Solid
1 1B
1B2 Konturerat
Outline
1C1 Täckande
Solid
1C
Konturerat
1C2 Outline
© Scania CV AB, Sweden
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 12 (18)
4.6 Artikelnummer eller annan märknings- 4.6 Part number or other marking infor-
uppgift mation
På denna plats i märkningsrutan anges det arti- This point in the marking box gives the part num-
kelnummer, den text eller beteckning som artikeln ber, text or designation that the part is to be mar-
ska märkas med. ked with.
Om utrymmet inte räcker och en upplysning ska If there is insufficient space and further informa-
lämnas, kan detta anges inom citattecken tion available then this can be indicated within
"….......", se exempel nedan. quotation mark "….......", see examples below.
Här ges några exempel på angivelser om märk- Below are several examples of indications for
ning: markings:
– 1234567 (artikelnummer) - 1234567 (part number)
– 1234567–1 (artikelnummerversion) - 1234567–1 (part number and version)
– 1234567 LH (artikelnummer vänster) - 1234567 LH (part number left-hand)
– INLET (text för anslutning) - INLET (text for a connection)
– "See note" (märkningsuppgiften finns - "See note" (information regarding
angiven i en not) marking is given in a note)
– "Resp Part No." (märkning med respektive - "Resp Part No." (marking with the
artikelnummer) respective part number)
Siffror och märkningstexter ska utföras i tecken- Numbers and marking texts are to be printed in
snitt Helvetica Regular (normal) eller liknande Helvetica Regular (normal) or similar within the
inom teckenfamiljen Linjärer. character family Grotesque.
Motor och rammärkning för lastbilar och bussar, Engine and frame marking for trucks and buses,
se STD4243. see STD4243.
På äldre ritningar kan beteckningen "dat" före- The designation "dat" may occur in older draw-
komma, vilket ska översättas med TXM i tabell 6. ings. It is to be replaced by TXM in table 6.
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 13 (18)
År Beteckning
Year Designation
1996 T
1997 V
1998 W
1999 X
2000 Y
2001 1
2002 2
2003 3
2004 4
2005 5
2006 6
2007 7
2008 8
2009 9
2010 A
© Scania CV AB, Sweden
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 14 (18)
Månad Beteckning
Month Designation
Januari / January A
Februari / February B
Mars / March C
April D
Maj / May E
Juni / June F
Juli / July G
Augusti / August H
September J
Oktober / October K
November L
December M
Då datummärkningen ska utföras med datum- If the date is to be marked in the form of a date
klocka eller datumfält, vilket framgår av den bok- dial or date field, as denoted by the alphabetical
stavsbeteckning som angivits, ska utförandena designation, it is to be done in accordance with
vara i likhet med de som visas i figurerna 5, 6 one of the examples in figures 5, 6 and 7.
och 7.
Fig. 5
(Visar/Indicates 2001 December)
Datumklocka
Date dial
Typ/Type X d = 12
Typ/Type V d = 20
© Scania CV AB, Sweden
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 15 (18)
95
96 96
97
98
98
99 00
00
02
01
02 04
03
04
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 16 (18)
1234567 VE 1234
1234567 VE 1234 123456
VE 1234
1234567 VE 1234
1234567 VE 1234 123456
VE 1234
1234567 VE 1234
1234567 VE 1234 123456
VE 1234
© Scania CV AB, Sweden
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 17 (18)
Exempel – märkning centrerad på två rader Example – a marking centred on two lines
Exempel – märkning centrerad på tre rader Example – a marking centred on three lines
© Scania CV AB, Sweden
Kontrollera att du har rätt utgåva Check that you have the right issue
STANDARD STD19
Approved / Assignor Area specialist Info class
KM Stefan Lindblom KM Sverker Sundmark P
Standard responsible Standard coordinator Date Issue Page
UTDH Markku Backholm UTDH Per Salberg 2007-03-19 20 18 (18)
Tabell 10 Utrymmesmått för några tecken- Table 10 Size of space for some character
höjder heights
Teckenhöjd L1 L2 L3 L4 L5 L6 h1 h2 h3
Character height
h
1,5 3,8 14 22,5 26 31 17 3,8 6 8,5
3 7,5 28 45 52 62 34 7,5 12 17
6 15 56 90 104 124 68 15 24 34
10 25 93 150 174 207 113 25 40 57
Kontrollera att du har rätt utgåva Check that you have the right issue