Professional Documents
Culture Documents
Check
1. The adaptive learning procedures and self-tests should be done with the VCM and Ford approved
diagnostic tool.
General Equipment: Ford approved diagnostic tool
2.
1. NOTE: The VCM LED prove-out confirms power and ground from the DLC to the VCM.
If the Ford approved diagnostic tool does not communicate with the VCM:
l check the VCMconnection to the vehicle
l check the Ford approved diagnostic tool connection to the VCM
l to diagnose no power to the Ford approved diagnostic tool,
Refer to: Communications Network (418-00 Module Communications Network, Diagnosis and
Testing).
3.
1. If the Ford approved diagnostic tool does not communicate with the vehicle:
l verify the ignition is in the RUN position
l verify Ford approved diagnostic tool operation with a known good vehicle
l to diagnose no power to the Ford approved diagnostic tool,
Refer to: Communications Network (418-00 Module Communications Network, Diagnosis and
Testing).
4.
1. Carry out the network test.
l If the Ford approved diagnostic tool responds with no communication from one or more
modules,
Refer to: Communications Network (418-00 Module Communications Network, Diagnosis and
Testing).
l If the network test passes, continue with the transmission adaptive learning procedures.
5. Verify that the calibration file is present on the scan tool. If the file is present, reconnect the scan tool
to the vehicle. If the file is not present, download the file from Ford service website.
Programming
1. Using the Ford approved diagnostic tool, navigate to the Module Reprogramming sub menu.
l Module Programming
l Module Reprogramming
l TCM
2. Follow the instructions displayed on the Ford approved diagnostic tool.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSCY/US/EN... 6/18/2019
Page 2 of 4
1. Using the Ford approved diagnostic tool, navigate to the Module Programming sub menu.
l Module Programming
l Programmable Module Installation
l TCM
2. Follow the instructions displayed on the Ford approved diagnostic tool.
3. NOTE: The following steps are for TR (Transmission Range) sensor adaptive learning.
1. Using the Ford approved diagnostic tool, navigate to the TCM Adaptive Learning sub menu.
l PCM
l TCM
l TCM Adaptive Learning
2. Select TR Sensor.
3. Select Perform Adaptive Learning.
4. Follow the instructions displayed on the Ford approved diagnostic tool.
4. NOTE: The following steps are for Shift drum adaptive learning.
1. Using the Ford approved diagnostic tool, navigate to the TCM Adaptive Learning sub menu.
l PCM
l Transmission
l TCM Adaptive Learning
2. Select Shift Drum.
3. Follow the instructions displayed on the Ford approved diagnostic tool.
1. Run engine until the instrument panel temperature gauge is reading between 1/3 and ½ of the
normal range.
2. Turn off all electrical accessories including rear defrost, HVAC, etc.
3. Using the Ford approved diagnostic tool, navigate to the TCM Adaptive Learning sub menu.
l PCM
l Transmission
l TCM Adaptive Learning
l Clutch
4. Select Clutch.
5. Follow the instructions displayed on the Ford approved diagnostic tool.
NOTE: It is important that consistent brake pedal pressure be maintained throughout the learn procedure.
NOTE: Do not turn the steering wheel during the learn procedure.
1. Using the Ford approved diagnostic tool, navigate to the TCM Adaptive Learning sub menu.
l PCM
l Transmission
l Clutch System Test
2. Follow the instructions displayed on the Ford approved diagnostic tool.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSCY/US/EN... 6/18/2019
Page 3 of 4
1. Using the Ford approved diagnostic tool, navigate to the TCM Adaptive Learning sub menu.
l PCM
l Transmission
l Speed Sensor Test
2. Select the desired speed sensor.
3. Follow the instructions displayed on the Ford approved diagnostic tool.
NOTE: If a drive cycle is not completed, the customer may feel erratic shifts and driveability concerns.
NOTE: To perform drive cycle, drive the vehicle on a level road surface.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSCY/US/EN... 6/18/2019
Page 4 of 4
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSCY/US/EN... 6/18/2019