Professional Documents
Culture Documents
1
DHP200D DTV Headend Processor User Manual
This user manual has been written to help people who have to use, to integrate and
Disclaimer
No part of this document may be reproduced in any form without the written
The contents of this document are subject to revision without notice due to
no liability for any error or damage of any kind resulting from the use of this
document.
Copy Warning
This document includes some confidential information. Its usage is limited to the
2
DHP200D DTV Headend Processor User Manual
Directory
3
DHP200D DTV Headend Processor User Manual
1.1 Outline
body with maximum 112 DVB-C QAM channels output. With 10G switch
built in, it can process 10G optical signal to work as a traditional QAM
modulator.
This processor is equipped with 2 card slots to load 32ch or 48ch or 64ch
QAM card. Its high density helps operators to save cost to the most extent.
1.2 Features
* Support 3 SFP+(10G)/SFP(1G) ports and 2 GE ports input & output from the front panel, or
RJ45 GE ports input & output from daughter cards (32/48QAM)
* High density, modularized plug-in design, 1U chassis with max 2 QAM cards
* Support multiplexer and scrambler with 6 CAS Simul-cryption
* Maximum 112 non-adjacent QAM carriers output
* Supports accurate PCR adjusting/CA filtering, PID remapping and PSI/SI editing
* Web-based Network management
1
DHP200D DTV Headend Processor User Manual
Carrier 1 Card 1
GE MUX 1# SCR 1# QAM 1#
IP 10G
Carrier 1~32
SFP+/SFP1
Carrier 32 RF out 1
GE
MUX 32# SCR 32# QAM 32#
512 IP in
IP 10G
SFP+/SFP2 64 IP out
Carrier 33
GE MUX 33# SCR 33# QAM 33#
Carrier 33~64
IP 10G
SFP+/SFP3 RF out 2
GE MUX 64# SCR 64# QAM 64# Carrier 64
Switch
IP GE1 Card 2
Carrier 1
GE MUX 1# SCR 1# QAM 1#
512 IP in Carrier 1~24
IP 48 IP out
GE2 RF out 1
GE Carrier 24
MUX 24# SCR 24# QAM 24#
Carrier 25
IP Data 1 MUX 25# SCR 25# QAM 25#
CH 1 CH 5 CH 31 CH 32 CH 33 CH 36 CH 63 CH 64
……… ………
384M 384M
Start Frequency End Frequency Start Frequency End Frequency
RF1 RF2
2
DHP200D DTV Headend Processor User Manual
Panel Illustration
2 3
1
Module 1 Module 2
4 5 6
3
DHP200D DTV Headend Processor User Manual
4
DHP200D DTV Headend Processor User Manual
This section is to explain the cautions the users must know in some case that possible injure
may bring to users when it‟s used or installed. For this reason, please read all details here and
make in mind before installing or using the product.
Avoid operating on a wet floor in the open. Make sure the extension cable is in good condition
Make sure the power switch is off before you start to install the device
Connecting
Grouding Connecting
Acquisition Installing Setting Running
Wire and Signal
Check Device Parameter Device
Power cable
Cord
When user installs machine frame array in one machine hall, the
Machine Hall Space distance between 2 rows of machine frames should be 1.2~1.5m
and the distance against wall should be no less than 0.8m.
Electric Isolation, Dust Free
Machine Hall Floor Volume resistivity of ground anti-static material:
5
DHP200D DTV Headend Processor User Manual
Grounding conductor must adopt copper conductor in order to reduce high frequency impedance,
and the grounding wire must be as thick and short as possible.
Users should make sure the 2 ends of grounding wire well electric conducted and be antirust.
It is prohibited to use any other device as part of grounding electric circuit
The area of the conduction between grounding wire and device‟s frame should be no less than
25 mm2.
All the machine frames should be connected with protective copper strip. The
grounding wire should be as short as possible and avoid circling. The area of the
conduction between grounding wire and grounding strip should be no less than
25mm2.
6
DHP200D DTV Headend Processor User Manual
Connecting the device‟s grounding rod to frame‟s grounding pole with copper wire.
The power socket is located on the right of rear panel, and the power switch is on
the left of front panel. User can plug one end of the power cord to the socket and
insert the other end to AC power. When the device solely connects to protective
ground, it should adopt independent way, say, share the same ground with other
devices. When the device adopts united way, the grounding resistance should be
The signal connections include the connection of input signal cable and the
7
DHP200D DTV Headend Processor User Manual
3.1 Login
The factory default IP address of this device is 192.168.0.136. Users can connect the
Connect the PC (Personal Computer) and the device with a net cable, and use ping
command to confirm they are on the same network segment. Launch the web browser
an input the device IP address in the browser‟s address bar and press Enter.
It will display the Login interface as Figure-1. Input the Username and Password
(Both the default Username and Password are “admin”. And then click “OK” to start
Figure-1
3.2 Operation
3.2.1 Summary
When we confirm the login, it will display the summary interface as Figure-2 where users have an
over view of the system information and alarm log.
8
DHP200D DTV Headend Processor User Manual
3.2.2 Monitor
Monitor → Module 1:
Clicking “Module 1”, it will display the interface as Figure-3 where users can check the input
status of Module 1.There are 7 input port, including 2 GE ports and 3 SFP ports at front panel,
Figure-3
3.2.3 Parameters
9
DHP200D DTV Headend Processor User Manual
Mudule 1/2
Click “Module 1 (or 2)”, it displays the interface as Figure-4 where users can configure the input IP
stream and multiplex channels to output. (Module 1 can be 32ch or 48ch QAM or blank as per order
config, while Module 2 is fixed to allow only 64ch QAM loaded or blank.)
Mux:
Operation Area
Figure-4
Click “+” to add IP input, then select one channel to parse, it will display the interface where users
can choose the programs to Mux out. (Figure-5)
10
DHP200D DTV Headend Processor User Manual
Figure-5
Configure „Input Area‟ and „Output Area‟ with buttons in „Operation Area‟. Instructions are as
below:
: To add input channel which come from Module GE1, Module GE2
:Enable/disable the CA Filter function. Clicking the box, user can filter the input CA to
Select one input program first and click this button to transfer the selected program to
the right box to output.
Similarly, user can cancel the multiplexed programs from the right box.
To select all the input programs
To select all the output programs
General:
Click “General”, it displays the interface where users can set parameters for each output channel
11
DHP200D DTV Headend Processor User Manual
Figure-7
PID Pass:
Clicking “PID pass”, it will display the interface as Figure-8 where user can add PIDs to be passed,
click the “+” symbol, input current IP channel number, then input current IP source PID and output
PID which is customer needed , then click “set” to apply the parameters.
12
DHP200D DTV Headend Processor User Manual
Figure-8
Scrambler:
Clicking “Scrambler”, it will display the interface where users can choose the programs to scramble.
(Figure-8)
Figure-8
IP Stream:
Module 1 (32ch qam module or 48ch qam module) supports TS to output in IP format through the
GE 1 & GE2 ports.
Click “IP Stream”, it displays the interface as Figure-9 where to set IP out parameters.
13
DHP200D DTV Headend Processor User Manual
Quickly Config
Figure-9
Modulator:
Clicking “Modulator”, it will display the interface as Figure-10 where to set RF output parameters.
Click “quickly
config” to set all
channels RF QAM
output parameters
Click “ Channel
config” to set each
channel RF QAM
output parameters
Figure-10
System:
Clicking “System”, it will display the interface as Figure-11 where to set network parameters.
14
DHP200D DTV Headend Processor User Manual
Figure-11
3.2.4 System
Figure-12
System → Network:
Clicking “Network”, it will display the interface as Figure-13
15
DHP200D DTV Headend Processor User Manual
Figure-13
System → Account
Clicking “Account”, it will display the screen as Figure-14 where to set the login account and
password for the web NMS.
Figure-14
System → Configuration:
Clicking “Configuration”, it will display the screen as Figure-15 where to set your configurations
for the device.
16
DHP200D DTV Headend Processor User Manual
Select areas
Figure-15
System → Firmware:
Clicking “Firmware”, it will display the screen as Figure-16 where to update firmware for the
device.
Figure-16
System → Date/Time:
Clicking “Date/Time”, it will display the interface as Figure-17 where users can set date/time for
this device.
17
DHP200D DTV Headend Processor User Manual
Figure-17
18