Professional Documents
Culture Documents
Datasheet
Datasheet
DESCRIPTION
The VB025SP is a high voltage power integrated PowerSO-10
circuit made using STMicroelectronics VIPower
Technology, with vertical current flow power
darlington and logic level compatible driving circuit.
Built-in protection circuits for coil current limiting
and collector voltage clamping allows the
VB025SP to be used as a smart, high voltage,
high current interface in advanced electronic
ignition systems.
BLOCK DIAGRAM
THERMAL DATA
o
R thj-case Thermal Resistance Junction Case (MAX) 1.2 C/W
o
R thj-h Thermal Resistance Junction Heatsink with FR4 (MAX) TBD (✭) C/W
o
T sold Lead Temperature During Soldering (MAX) TBD (✭) C
st
(✭) see application note AN515/1094 on VIPower data-book 1 edition.
2/7
VB025SP
CONNECTION DIAGRAM
PIN FUNCTION
No NAME FUNCTION
1-5 GND Emitter Power Ground
6 GND Control Ground (*)
7 V CC Logic Supply Voltage
8 BD Base Darlington
9 INPUT Logic Input Channel (Internal Pull Down)
10 FLAG Diagnostic Output Signal (Open Emitter)
TAB HVC Primary Coil Output Driver (Open Collector)
(*) Pin 6 must be connected to pins 1-5 externally
ELECTRICAL CHARACTERISTICS (5.3V < Vb < 24V; VCC = 5 V ± 10%; -40oC < Tj < 125oC;
Rcoil = 580 mΩ; Lcoil = 3.75 mH; unless otherwise specified; see note 1)
Symbol Parameter Test Conditions Min. Typ. Max. Unit
Vcl High Voltage Clamp I coil = 6.5 A 320 380 420 V
V ce(sat) Saturation Voltage of The I c = 6.5A; V in = 4V 1.5 2 V
Power Stage
I CC(stdby) Stand-by Supply Current IN = OFF 10 mA
I CC DC Logic Current V b = 16 V I c = 6.5 A f = 100 Hz 40 mA
Load = Coil V CC = 5.5V
I CC(peak) Peak DC Logic Current I c = 6.5 A (see figure 1) 100 150 mA
During On Phase
V CC DC Logic Voltage 4.5 5.5 V
o o
I cl Coil Current Limit -40 C < T j < 125 C 8.25 10 A
(see note 2 and figure 1)
I c(leak) Output leakage Current IN = OFF V HVC = 24V 0.8 mA
I C(infl) Collector Current with VCC = 5 V VBat = 13.5 V 0.8 mA
Floating Input R LOAD = 1KΩ; Input Floating
o
T Ic_ctr Thermal Temperature OUT = ON (see figure 2) 150 (*) C
Output Current Control
3/7
VB025SP
Fig. 1 Main Waveforms During On Phase Fig. 2 Output Current Waveform After Thermal
Protection Activation
Fig. 3 Flag Current Versus Temperature FIG. 4 Single Pulse Typical Es/b Curve
200 V
HVC
50 %
10 %
INPUT
10 %
t pHL t pLH
SC10930
5/7
VB025SP
mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
A 3.35 3.65 0.132 0.144
A1 0.00 0.10 0.000 0.004
B 0.40 0.60 0.016 0.024
c 0.35 0.55 0.013 0.022
D 9.40 9.60 0.370 0.378
D1 7.40 7.60 0.291 0.300
E 9.30 9.50 0.366 0.374
E1 7.20 7.40 0.283 0.291
E2 7.20 7.60 0.283 0.300
E3 6.10 6.35 0.240 0.250
E4 5.90 6.10 0.232 0.240
e 1.27 0.050
F 1.25 1.35 0.049 0.053
H 13.80 14.40 0.543 0.567
h 0.50 0.002
L 1.20 1.80 0.047 0.071
q 1.70 0.067
α 0o 8o
0.10 A B
10 6
=
=
=
=
=
H E E2 E3 E1 E4
=
=
=
=
=
1 5
SEATING
PLANE
e B DETAIL "A" A
0.25 M C
Q
D
h = D1 =
= =
SEATING
PLANE
A
F
A1 A1
L
DETAIL "A"
α
0068039-C
6/7
VB025SP
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is
granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are
subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products
are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a trademark of STMicroelectronics
http://www.st.com
.
7/7