Professional Documents
Culture Documents
Grove RT600E: Product Guide
Grove RT600E: Product Guide
Product Guide
Features
• 10 m - 32 m (33 ft - 105 ft) four-section
full power boom
Stowage
Large open stowage
compartment for tools and
rigging accessories.
Superstructure
The superstructure features a full
power four section boom with a
four plate rectangular design that can
reach to a max tip height of 112 ft.
The synchronized extension feature
telescopes boom sections at the touch of
the hand from an easy to use single lever
joystick controller.
Contents
Specifications 4
Working range 8
Load charts 9
Load handling 13
Notes 14
Specifications
Superstructure
Cab
Carrier
Steering
Chassis
Fully independent power steering:
Box section frame fabricated from high-strength, low
alloy steel. Integral outrigger housings and front/rear Front: Full hydraulic, steering wheel controlled.
lifting, towing, and tie down lugs. Rear: Full hydraulic, switch controlled.
Carrier continued
*Optional equipment
508 mm
(1'-8") 12 448,3 mm
(41'-11") 3894,6 mm
(12'-9")
286 mm 965,2 mm 838,2 mm
(11.25") (3'-2") (2'-9")
967 mm
(38.06")
1700,2 mm
(5'-7")
3497,4 mm
(11'-6") 3531 mm
(11'-7.0")
4743,5 mm
781,0 mm (15'-7") 1645,0 mm
21.30° (5'-5")
(2'-7")
22.10°
494,04 mm (1'-7")
1905,0 mm
3390,9 mm (6'-3") 3390,9 mm
(11'-2") (11'-2") 306 mm
3759 mm (12'-4") (12")
7759 mm (25'-5")
R 6400 mm (21'-0")
R 10 363 mm (34'-0") 4-WHEEL
STEER RADIUS
R 14 173 mm 2-WHEEL
R 13 564 mm (44'-6") STEER RADIUS
(46'-6") R 11 125 mm R 3918 mm (12'-10.25")
22°
(36'-6") 22°
R 1545,18 mm R 1827,52 mm
28° 5'-11" (26') 28°
CAB SWING CAB SWING
Weights
GVW Front Rear
Add: 450 ft of wire rope on Auxiliary Hoist 255 (563) -96 (-213) 342 (755)
-102
Add: Auxiliary boom nose 59 (131) 162 (358) (-227)
Add: 7,5 t (8.3 USt) headache ball 161 (355) 279 (616) -118 (-261)
Grove RT600E 7
Working range
H [ft]
180
0°
170
51' EXT.
25°
160
45°
150
29' EXT.
140
130
120
105
70°
100
110 60°
90
100 50°
80
90
40°
70
80
60
70 30°
50
60
40
20°
50
33
40
10°
30
78°
MAX.
20 BOOM
ANGLE
0°
10
0
150 140 130 120 110 100 90 80 70 60 50 40 30 20 10
Axis of
Rotation
R [ft]
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
8 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
Load chart RT650E
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT600E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 9
Load chart RT640E
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
10 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart RT600E
Pounds Pounds
**29 ft LENGTH 51 ft LENGTH
#9005
#0021 #0022 #0023 #0041 #0042 #0043
Feet 0° 25° 45 ° 0 ° 25° 45° Main boom length in feet
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET Feet
33 40 50 60 70
*9000 38,550 38,550
30 (78) 10 (69.5) (73.5)
9000 *6000 32,550 32,550 32,550
35 12
(77) (78) (65.5) (70.5) (75)
40 9000 8000 6000 23,700 23,700 23,700 23,700
(74.5) (77.5) (77) 15 (59.5) (65.5) (71) (75)
9000 7560 *5660 6000 14,450 14,450 14,450 14,450 14,450
45 (72.5) (76) (78) (76) 20
(47.5) (57) (64.5) (69.5) (73)
8760 7170 5600 6000 9640 9640 9640 9640 9640
50 25
(70) (74) (76) (74) (32) (47) (58) (64.5) (68.5)
55 8030 6820 5500 6000 *4120 6840 6840 6840 6840
(67.5) (71.5) (73.5) (72) (78) 30
(34.5) (50.5) (58.5) (64)
7380 6500 5300 6000 3900 4850 4850 4850
60 35
(65) (69) (71) (70) (77) (41.5) (52.5) (59)
6770 6210 5180 6000 3710 *2740 3450 3450 3450
65
(62.5) (66.5) (68.5) (68) (75) (78) 40 (30.5) (46) (54)
6210 5950 4890 5620 3530 2660
70 (60) (64) (66) (66) (72.5) (76.5) 45 2410 2410
(38) (48.5)
5710 5710 4620 5210 3370 2580
75 1610 1610
(57.5) (61.5) (63) (64) (70.5) (74) 50 (28) (42.5)
5250 5500 4370 4860 3220 2520
80 Min. boom angle (°) for indicated length (no load) 30
(55) (58.5) (60.5) (61.5) (68.5) (72)
°
Max. boom length (ft) at 0 boom angle (no load) 60
4790 5300 4100 4540 3080 2460
85 (52) (56) (57.5) (59.5) (66) (69.5) NOTE: ( ) Boom angles are in degrees.
4090 4650 3820 4260 2960 2410 #LMI operating code. Refer to LMI manual for operating instructions.
90
(49) (53) (54) (57) (63.5) (67)
95 3480 3960 4000 2850 2360
(46) (49.5) (55) (61.5) (64.5) Lifting capacities at zero degree boom angle
on rubber - 360°
2930 3350 3770 2750 2330
100 (42.5) (46) (52.5) (59) (62) Main boom length in feet
Boom
2440 2810 3360 2660 2300 angle 33 40 50
105
(39) (42.5) (50) (56) (59) 7580 4850 2410
0° (28.2) (35) (45)
110 2000 2320 2910 2570 2280
(35) (38.5) (47.5) (53.5) (56) NOTE: ( ) Reference radii in feet. A6-829-100836B
1610 2500 2500
115
(30.5) (44.5) (50.5)
1250 2120 2430
120
(25.5) (41.5) (47.5)
1780 2250
125
(38.5) (44.5) NOTES:
1470 1820
130
(35) (40.5) 1. All capacities above the bold line are based on
1180 1420 structural strength of boom extension.
135
(31) (36.5)
Min. boom
angle for 2. 29 ft and 51 ft boom extension lengths may be used for
° 32° 45° 25° 35° 45° single line lifting service.
indicated length 24
(no load)
Max. boom 3. Radii listed are for a fully extended boom with the
length at 0° 90 ft 90 ft boom extension erected. For main boom lengths less
boom angle than fully extended, the rated loads are determined by
(no load)
boom angle. Use only the column which corresponds
NOTE: ( ) Boom angles are in degrees. A6-829-100845A
#LMI operating code. Refer to LMI manual for instructions.
to the boom extension length and offset for which the
*This capacity based on maximum boom angle. machine is configured. For boom angles not shown,
**29 ft capacities are also applicable to fixed offsettable ext. use the rating of the next lower boom angle.
However, the LMI codes will change to #0051, #0052 and #0053
for 0°, 25° and 45° offset, respectively.
WARNING: Operation of this machine with heavier
loads than the capacities listed is strictly prohibited.
Machine tipping with boom extension occurs rapidly
and without advance warning.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT600E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 11
Load charts
33 ft-105 ft 12,008 lb Stationary Defined arc over front 33 ft-105 ft 12,008 lb Pick & carry Boom centered
up to 2.5 mph over front
Pounds Pounds
#9005 #9006
Main boom length in feet Main boom length in feet
Feet 33 40 50 60 70 Feet 33 40 50 60 70
10 46,600 40,800 34,600 30,150 30,150 17,850
(69.5) (73.5) (77) 10
(69.5) (73.5) (77)
40,800 40,800 34,600 30,150 30,150 17,850
12 (65.5) (70.5) (75) 12 (65.5) (70.5) (75)
34,000 34,000 34,000 26,650 21,500 29,650 29,650 17,850 17,850 14,750
15 (59.5) (65.5) (71) (75) (77.5) 15 (59.5) (65.5) (71) (75) (77.5)
20 26,050 26,050 26,050 26,050 21,500 22,650 22,650 17,850 17,850 14,750
(47.5) (57) (64.5) (69.5) (73) 20 (47.5) (57) (64.5) (69.5) (73)
25 18,200 18,200 18,200 18,200 18,200 17,850 17,850 17,850 17,850 14,750
(32) (47) (58) (64.5) (68.5) 25
(32) (47) (58) (64.5) (68.5)
30 13,100 13,100 13,100 13,100 13,100 13,100 13,100 13,100
(34.5) (50.5) (58.5) (64) 30
(34.5) (50.5) (58.5) (64)
10,050 10,050 10,050 10,050 10,050 10,050
35 (41.5) (52.5) (59) 35 (41.5) (52.5) (59)
40 7900 7900 7900 7340 7340 7340
(30.5) (46) (54) 40 (30.5) (46) (54)
45 6290 6290 6020 6020
(38) (48.5) 45
(38) (48.5)
50 5050 5050 4940 4940
(28) (42.5) 50
(28) (42.5)
4060 4030
55 (35) 55 (35)
3260 3260
60 (26) 60 (26)
Min. boom angle (°) for indicated length (no load) 0 Min. boom angle (°) for indicated length (no load) 0
Max. boom length (ft) at 0° boom angle (no load) 70 Max. boom length (ft) at 0° boom angle (no load) 70
NOTE: ( ) Boom angles are in degrees. NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for operating instructions. #LMI operating code. Refer to LMI manual for operating
instructions.
Lifting capacities at zero degree boom angle Lifting capacities at zero degree boom angle
on rubber - Defined arc over front on rubber - Pick & carry
Boom Main boom length in feet Boom Main boom length in feet
angle 33 40 50 60 70 angle 33 40 50 60 70
0° 14,550 10,050 6290 4060 2590 14,550 10,050 6020 4030 2590
(28.2) (35) (45) (55) (65) 0° (28.2) (35) (45) (55) (65)
NOTE: ( ) Reference radii in feet. A6-829-100835B NOTE: ( ) Reference radii in feet. A6-829-100837B
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
12 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load handling
When lifting over swingaway and/or jib combinations, The approximate weight of 3/4 in wire rope is 1.5 lb/ft
deduct total weight of all load handling devices reeved
over main boom nose directly from swingaway or jib
capacity. Hoist performance
Wire Hoist line pulls Drum rope
rope two-speed hoist capacity (ft)
NOTE: All load handling devices and boom attachments layer
are considered part of the load and suitable allowances Low High Layer Total
available available
MUST BE MADE for their combined weights. Weights are lb* lb*
for Grove furnished equipment.
1 18,134 9067 101 101
REAR AXLE
360° CENTERLINE
CENTERLINE OSCILLATION
OVER OF OUTRIGGER 360°
OF BOOM LOCKOUTS MUST
SIDE SUPPORT
BE SET TO
BOOM MAINTAIN 360°
CENTERED CAPACITIES
LONGITUDINAL
CENTERLINE OVER FRONT
OF CRANE
6°
CG OF OVER OVER
LOAD FRONT REAR 12°
DIAGRAM
FOR LIFTING CENTERLINE DIAGRAM C6-829-003529
ON OUTRIGGERS OVER FOR LIFTING C6-829-001159
OF ROTATION
SIDE ON TIRES
Bold lines determine the limiting position of any load for operation within working areas indicated.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT600E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 13
Notes
14
Notes
Grove RT600E 15
Manitowoc Cranes
Regional headquarters
Americas Europe, Middle East, Africa China Greater Asia-Pacific
Manitowoc, Wisconsin, USA Ecully, France Shanghai, China Singapore
Tel: +1 920 684 6621 Tel: +33 (0)4 72 18 20 20 Tel: +86 21 6457 0066 Tel: +65 6264 1188
Fax: +1 920 683 6277 Fax: +33 (0)4 72 18 20 00 Fax: +86 21 6457 4955 Fax: +65 6862 4040
Shady Grove, Pennsylvania, USA
Tel: +1 717 597 8121
Fax: +1 717 597 4062
Regional offices
Americas
Brazil
China
Beijing
Factories This document is non-contractual. Constant improvement and engineering progress
make it necessary that we reserve the right to make specification, equipment, and price
Brazil changes without notice. Illustrations shown may include optional equipment and
Alphaville Chengdu accessories and may not include all standard equipment.
Alphaville
Mexico Guangzhou
China
Monterrey Xian
TaiAn
Chile
Zhangjiagang
Santiago Greater Asia-Pacific
France
Australia
Charlieu
Europe, Middle East, Adelaide
Moulins
Africa Brisbane
Germany
Czech Republic Melbourne
Wilhelmshaven
Netvorice Sydney
India
France India
Pune
Baudemont Calcutta
Italy
Cergy Chennai
Niella Tanaro
Decines Delhi
Portugal
Germany Hyderabad
Baltar
Langenfeld Pune
Fânzeres
Hungary Korea
Slovakia
Budapest Seoul
Saris
Italy Philippines
USA
Lainate Makati City
Manitowoc
Netherlands Singapore
Port Washington
Breda
Shady Grove
Poland
Warsaw
Portugal
Baltar
Russia
Moscow
U.A.E.
Dubai
U.K.
Buckingham
©2011 Manitowoc
Printed in USA
Form No. RT600E
Part No. 03-473-2M-0411 www.manitowoc.com