Professional Documents
Culture Documents
4 – Wireless Topologies
Overview
1
Components
2
Clients and adapters
An access point (AP) is a WLAN device that Wireless Bridges are designed to
can act as the center point of a stand-alone connect two or more networks that
wireless network or be used as the are typically located in different
connection point between wireless and wired buildings.
networks.
Not currently covered under 802.11
3
AP
Antennas
• Cisco Aironet AP 2.4 GHz antennas are compatible with all Cisco
RP-TNC equipped APs.
• The antennas are available with different gain and range capabilities,
beam widths, and form factors.
• Coupling the right antenna with the right AP allows for efficient
coverage in any facility, as well as better reliability at higher data rates.
• A detailed coverage of antennas will be provided later in the
course.
Rick Graziani graziani@cabrillo.edu 7
Bridge
Antennas
• Cisco Aironet bridge 2.4 GHz antennas provide transmission between two or
more buildings.
• Antennas operate at Layer 1 of the OSI Model.
• Remember that the physical layer defines the electrical, mechanical,
procedural, and functional specifications for activating, maintaining, and
deactivating the physical link between end systems.
• Characteristics such as voltage levels, timing of voltage changes, physical data
rates, maximum transmission distances, physical connectors, and other,
similar, attributes are defined by physical layer specifications.
Rick Graziani graziani@cabrillo.edu 8
4
WLAN Topologies
Includes
APs,
wireless
bridges
5
Local area networks (LAN)
6
Minimal Overlap Coverage Option
SSID = Student
Channel 1
SSID = Student
Channel 6
Wireless repeater
50%
overlap
7
System redundancy and load balancing
Multiple Vendors
Redundancy only
• With the Cisco DS systems, the units are set to different channels.
• Redundancy: If one unit goes down, remote clients will hand off to the
remaining unit and continue working.
• Load balancing: This can be configured based on the number of
users, the bit error rate, or signal strength.
– Distributes user connections across available access points
– Optimizes aggregate throughput
8
Multiple Overlapping Networks Coverage
Option
SSID = Staff
SSID = Student Channel 6
Channel 1
SSID = Public
Channel 11
9
Roaming
Roaming
10
Roaming IAPP: Please
send buffered
frames for…
IAPP: Ok!
* Packet - Source
MAC of client…
Roaming
• Scans for a better access point if
the signal strength falls below a
threshold value.
• The following options define signal
strength and wait thresholds that
trigger a new scan.
11
Scalability
APs are on
different channels
Scalability
APs are on
different channels
12
Scalability
• Specifies the channel number and frequency that the client adapter
uses for communications. The channels conform to the IEEE 802.11
Standard for your regulatory domain.
• In infrastructure mode, this option is set automatically and cannot be
changed. The client adapter listens to the entire spectrum, selects the
best access point, and then uses the same channel as that access
point.
• In ad hoc mode, the channel of the client adapter must match the
channel used by the other clients in the wireless network. If the client
adapter does not find any other ad hoc client adapters, this option
specifies the channel on which the client adapter broadcasts beacons.
Rick Graziani graziani@cabrillo.edu 25
Channel Setup
13
Channel Setup
14
Access point coverage and comparison
• The Cisco Aironet 2.4 GHz radio delivers 100 mW of output and
offers a high degree of receiver sensitivity.
• The 5 GHz client radio has a 20 mW transmit power and the 5 GHz
access point has a 40 mW transmit power.
• It is possible to adjust the power level down, to create pico-cells, or
smaller coverage cells.
• This would be done, for example, to prevent the coverage area of one
AP from extending too far into the coverage area of another AP.
Rick Graziani graziani@cabrillo.edu 29
• Sets the transmit power level of the radio. Select a value for Transmit
Power that is no greater than the maximum allowed by the regulatory
body in your country (FCC in the United States, ETSI in Europe, and
MKK in Japan). Reducing the transmit power conserves battery power,
but it reduces the range of the radio. The default power level is the
maximum power allowed by the regulatory agency in your country.
• Note: If World Mode is enabled, the transmit power is limited to the
maximum level allowed by the regulatory agency of the country where
the adapter is used.
Rick Graziani graziani@cabrillo.edu 30
15
Multirate implementation
16
Bridge Topologies
Root modes
• Cisco Aironet access points and bridges have two different root
modes, in which to operate the following:
– Root = ON —
• The bridge or AP is a root.
• If it is a bridge, then it is called the master bridge.
– Root = OFF —
• The bridge or AP is not a root, non-root.
Rick Graziani graziani@cabrillo.edu 34
17
Root modes
Root modes
on on
off
off
off
off
18
Point-to-point configuration
Point-to-point configuration
19
Point-to-multipoint configuration
root
Non-root Non-root
Distance limitations
• The 802.11 standard sets a time limit for the acknowledgement of packets.
• Remember that 802.11 also defines a Local Area Network, which means a
typical wireless range of up to 305 m (1000 ft), not several kilometers or
miles.
• The bridge products have a parameter that increases this timing, whereas
the workgroup bridge and AP does not.
• The timing is increased, by violating the 802.11 standard.
• This allows the Cisco devices to operate at greater distances.
• Any wireless bridge that supports distances over one mile must violate
802.11.
• This means that radios of other 802.11 vendors may not work with the
Cisco bridges when the distances are greater than 1.6 km (1 mile).
Rick Graziani graziani@cabrillo.edu 40
20
Sample Topologies
Basic Topologies
Extended
Infrastructure
Topology (ESS)
21
Campus topologies
• One of the biggest benefits of a campus WLAN is the ability for people
to sit in common areas and work together, and still easily get network
access.
Rick Graziani graziani@cabrillo.edu 43
22
VLAN, QoS, and Proxy Mobile IP
VLAN features
• The Cisco Aironet APs only support the 802.1Q Trunking protocol
standard.
• Switches will not allow different VLANs to talk to one another.
• A router will be needed to allow different VLANs to communicate to
each other.
• The Cisco Aironet APs can be configured with 16 different VLANs
for system design flexibility.
• WLANs can now fit nicely into the larger network because VLANs have
been enabled on the APs.
• This allows WLAN users to roam from access point to access point
maintaining connectivity to the proper VLAN.
Rick Graziani graziani@cabrillo.edu 46
23
Quality of Service (QoS) feature
• Time critical data traffic such as voice and video benefit from
Quality of Service (QoS), which can be configured to give voice and
video higher priority.
• This allows for smooth voice communication, jitter free video, and
reliable delivery of E-Mail configured with a lower priority.
• Class of Service (CoS) uses the 802.1P standard to set the priority
field to network traffic.
• 802.11e is supplementary to the MAC layer to provide QoS support for
LAN applications.
Rick Graziani graziani@cabrillo.edu 47
Proxy mobile IP
24
Ch. 4 – Wireless Topologies
25