Professional Documents
Culture Documents
technical guide
U N D E R F LO O R H E AT I N G
AND COOLING
05 | 2014
The Uponor Nubos product line
Small bend radii possible and no additional items needed to Pipe fixation in distribution areas
implement diagonal 45 degree pipe direction
Additional accessories
180
K K 30 mm
K
30 25
35
40
2)
Limit curve
5,5
160
K
20
14 x 2 PE-Xa
140
Specific thermal output q in [W/m2]
120
K
15
7F 335 -F
100 1)
Limit curves
5.5
11
80 16.5
10 K
22
27.5
60 8K
33
6K
40
– θi = 4 K
Δθ H = θ H
20
0
33 27.5 Vz 22 .5
Thermal resistance
Vz Vz 16 Vz 11
Vz Δθ
Rl,B in [m2 K/W]
Vz 5.5 Vz qH
0.05 cm W/m2 K
0.10
Heating 5.5
11
16.5
22
95.7
89.6
82.5
74.5
12.1
13.7
15.0
16.1
27.5 66.0 16.9
33 58.3 17.5
0.15
1) Limit curve valid for θi20 °C and θF, max 29 °C or θi 24 °C and θF, max 33 °C
2) Limit curve valid for θi 20 °C and θF, max 35 °C
Note: According to DIN EN 1264 baths, showers and toilets are not included.
Limit curves must not be exceeded.
Maximum design supply water temperature: θV, des = ΔθH, g + θi + 2.5 K
ΔθH, g results from the limit curve for the occupied zone with the smallest pipe spacing.
180
K K 30 mm
K
30 25
35
40
2)
Limit curve
5.5
160
K
20
16 x 1.8 PE-Xa
140
120
Thermal resistance q in [W/m2]
K
15
7F 336 -F
100 1)
Limit curves
5.5
11
80 16.5
10 K
22
27.5
60 8K
33
6K
40
– θi = 4 K
Δθ H = θ H
20
0
33 27.
5 Vz 2
2 .5 Vz 11
Thermal resistance
Vz Vz 16
Rl,B in [m2 K/W]
Vz Vz 5.5 Vz qH Δθ
0.05 cm W/m2 K
0.10
Heating 5.5
11
16.5
22
95.6
89.4
82.0
73.8
12.0
13.3
14.4
15.3
27.5 65,0 15.9
33 56.9 16.4
0.15
1) Limit curve valid for θi20 °C and θF, max 29 °C or θi 24 °C and θF, max 33 °C
2) Limit curve valid for θi 20 °C and θF, max 35 °C
Note: According to DIN EN 1264 baths, showers and toilets are not included.
Limit curves must not be exceeded.
Maximum design supply water temperature: θV, des = ΔθH, g + θi + 2.5 K
ΔθH, g results from the limit curve for the occupied zone with the smallest pipe spacing.
180
K K 30 mm
K
30 25
35
40
2)
Limit curve
5.5
160
K
20
14 x 1.6 MLCP
140
Specific thermal output q in [W/m2]
120
K
15
7F 337 -F
100 1)
Limit curves
5.5
11
80 16.5
10 K
22
27.5
60 8K
33
6K
40
θi = 4 K
ΔθH = θH
–
20
0
33 27.5 Vz 22 .5
Thermal resistance
Vz Vz 16 Vz 11 Δθ
Vz
Rl,B in [m2 K/W]
Vz qH
Vz 5.5 cm W/m2 K
0.05
5.5 95.6 11.9
0.10
Heating 11
16.5
22
89.5
82.1
73.8
13.2
14.3
15.2
27.5 65.0 15.7
33 56.9 16.2
0.15
1) Limit curve valid for θi20 °C and θF, max 29 °C or θi 24 °C and θF, max 33 °C
2) Limit curve valid for θi 20 °C and θF, max 35 °C
Note: According to DIN EN 1264 baths, showers and toilets are not included.
Limit curves must not be exceeded.
Maximum design supply water temperature: θV, des = ΔθH, g + θi + 2.5 K
ΔθH, g results from the limit curve for the occupied zone with the smallest pipe spacing.
180
K K 30 mm
K
30 25
35
40
2)
Limit curve
5.5
160
K
20
16 x 2 MLCP
140
Specific thermal output q in [W/m2]
120
K
15
7F 338 -F
100 1)
Limit curves
5.5
11
80 16.5
10 K
22
27.5
60 8K
33
6K
40
– θi = 4 K
Δθ H = θ H
20
0
33 27.
5 Vz 2
2
Vz 16
.5 Vz 11 Δθ
Vz Vz qH
Rl,B in [m2 K/W]
Vz Vz 5.5 cm W/m2 K
0.05
5.5 95.6 12.0
0.10
Heating 11
16.5
22
89.4
82.0
73.8
13.3
14.5
15.4
27.5 65.7 15.9
33 57.1 16.5
0.15
1) Limit curve valid for θi20 °C and θF, max 29 °C or θi 24 °C and θF, max 33 °C
2) Limit curve valid for θi 20 °C and θF, max 35 °C
Note: According to DIN EN 1264 baths, showers and toilets are not included.
Limit curves must not be exceeded.
Maximum design supply water temperature: θV, des = ΔθH, g + θi + 2.5 K
ΔθH, g results from the limit curve for the occupied zone with the smallest pipe spacing.
180 2)
Limit curve
45 mm
K K 5.5
K
30 25
35
40
160
K
20
14 x 2 PE-Xa
140
Specific thermal output qH in [W/m2]
120
5K
=1
– θi 7F 335 -F
=θ H
Δθ H
1)
Limit curves
100
5.5
11
16.5
22
27.5
80 80
33 10 K
6K
40 40
θC =4K
ΔθC = θi –
20 20
0 0
3
Vz
3 27.5 Vz 22 Vz 16
.5 Vz 11 Vz 5.5
Vz Vz qH ΔθH,N
0.05 cm W/m2 K
Heating 5.5
11
100.0
98.0
13.9
16.3
Thermal resistance
0.10
22 90.5 20.9
27.5 84.2 22.7
33 76.0 24.0
0.15 0
22 6.5 Vz 11 Vz 5.5
Vz Vz 1
Vz qC ΔθC,N 0.05
W/m2
Cooling cm
5.5
11
39.0
34.0
K
8
8 0.10
16.5 30.0 8
22 26.3 8
0.15
1) Limit curve valid for θi20 °C and θF, max 29 °C or θi 24 °C and θF, max 33 °C
2) Limit curve valid for θi 20 °C and θF, max 35 °C
Note: According to DIN EN 1264 baths, showers and toilets are not included.
Limit curves must not be exceeded.
Maximum design supply water temperature: θV, des = ΔθH, g + θi + 2.5 K
ΔθH, g results from the limit curve for the occupied zone with the smallest pipe spacing.
When cooling, supply temperature should be higher than dew point temperature. A humidity sensor is to be used.
180
2) 45 mm
K 5.5
Limit curve
K
K
30 25
35
40
160
K
20
16 x 1.8 PE-Xa
140
Specific thermal output qH in [W/m2]
120
5K
=1
– θi 7F 336 -F
=θ H
Δθ H 1)
1)
Limit curves
100
11 5.5
16.5
22
27.5
80 80
33 10 K
6K
40 40
θC = 4 K
Δθ C = θ i –
20 20
0 0
3 .5 Vz 2
2 .5 Vz 11 Vz 5.5
Vz
3
Vz
27 Vz 16 Vz qH ΔθH,N
0.05 cm W/m2 K
Heating 5.5
11
100.0
97.9
13.7
15.8
Thermal resistance
0.10
22 89.9 29.9
27.5 83.4 21.6
33 74.7 22.5
0.15 0
2 2 6. 5 11 5.5
Vz Vz1 Vz Vz
Vz qC ΔθC,N 0.05
W/m2
Cooling cm
5.5
11
39.4
34.8
K
8
8 0.10
16.5 30.7 8
22 27.2 8
0.15
1) Limit curve valid for θi20 °C and θF, max 29 °C or θi 24 °C and θF, max 33 °C
2) Limit curve valid for θi 20 °C and θF, max 35 °C
Note: According to DIN EN 1264 baths, showers and toilets are not included.
Limit curves must not be exceeded.
Maximum design supply water temperature: θV, des = ΔθH, g + θi + 2.5 K
ΔθH, g results from the limit curve for the occupied zone with the smallest pipe spacing.
When cooling, supply temperature should be higher than dew point temperature. A humidity sensor is to be used.
K
30 25
35
40
160
K
20
14 x 1.6 MLCP
140
Specific thermal output qH in [W/m2]
120
5K
=1
– θi 7F 337 -F
=θ H
100
1)
Limit curves Δθ H
5.5
11
16.5
22
27.5
80 80
33 10 K
6K
40 40
θC = 4 K
Δθ C = θ i –
20 20
0 0
33 27.5 Vz 22 Vz 16
.5 Vz 11 Vz 5.5
Vz Vz Vz qH ΔθH,N
0.05 cm W/m2 K
Heating 5.5
11
100.0
97.9
13.7
15.7
Thermal resistance
0.10
22 89.9 19.8
27.5 83.3 21.4
33 74.5 22.3
0.15 0
22 6.5 Vz 11 Vz 5.5
Vz Vz 1
Vz qC ΔθC,N 0.05
W/m2
Cooling cm
5.5
11
39.4
34.9
K
8
8 0.10
16.5 30.9 8
22 27.2 8
0.15
1) Limit curve valid for θi20 °C and θF, max 29 °C or θi 24 °C and θF, max 33 °C
2) Limit curve valid for θi 20 °C and θF, max 35 °C
Note: According to DIN EN 1264 baths, showers and toilets are not included.
Limit curves must not be exceeded.
Maximum design supply water temperature: θV, des = ΔθH, g + θi + 2.5 K
ΔθH, g results from the limit curve for the occupied zone with the smallest pipe spacing.
When cooling, supply temperature should be higher than dew point temperature. A humidity sensor is to be used.
K
30 25
35
40
160
K
20
16 x 2 MLCP
140
Specific thermal output qH in [W/m2]
120
5K
=1
– θi 7F 338 -F
=θ H
100
1)
Limit curves ΔθH
1)
11 5.5
16.5
22
27.5
80 80
33 10 K
6K
40 40
θC = 4 K
Δθ C = θ i –
20 20
0 0
33 .5 Vz 2
2 .5 Vz 11 Vz 5.5
Vz Vz
27 Vz 16 Vz qH ΔθH,N
0.05 cm W/m2 K
Heating 5.5
11
100.0
97.9
13.8
15.9
Thermal resistance
0.10
22 90.0 20.0
27.5 83.5 21.7
33 74.8 22.7
0.15 0
2 2 6. 5 11 5.5
Vz Vz1 Vz Vz
Vz qC ΔθC,N 0.05
W/m2
Cooling cm
5.5
11
39.3
34.6
K
8
8 0.10
16.5 30.7 8
22 27.1 8
0.15
1) Limit curve valid for θi20 °C and θF, max 29 °C or θi 24 °C and θF, max 33 °C
2) Limit curve valid for θi 20 °C and θF, max 35 °C
Note: According to DIN EN 1264 baths, showers and toilets are not included.
Limit curves must not be exceeded.
Maximum design supply water temperature: θV, des = ΔθH, g + θi + 2.5 K
ΔθH, g results from the limit curve for the occupied zone with the smallest pipe spacing.
When cooling, supply temperature should be higher than dew point temperature. A humidity sensor is to be used.
400
Pressure losses in the
Uponor Comfort Pipes can 300
0.6
.8
x1
0.5
m/
100 16
mm
0.4
m/
s
x2
80
s
m/
.
0.3
60 14
s
m/
50
0.2
s
40
m/
0.1
s
30
5m
0.
/s
1
20
m/
10 s
0.1 0.2 0.3 0.5 1 2 3 4 5 6 7 8 9 [mbar/m]
0.01 0.02 0.03 0.05 0.1 0.2 0.3 0.4 0.5
[kPa/m]
Pressure gradient R
400
Pressure losses in the 300
Uponor MLCP RED can be
determined with the aid of 200
this diagram.
Mass flow rate m in [kg/h]
0.6
mm m
x 2 .6 m 0.5
m/
100
6
0.4
1 x1 m/
s
80
14 s
.
m/
0.3
60
s
m/
50
0.2
40
m/
0.1
30
5
m/
0.
s
1
20
m/
s
10
0.1 0.2 0.3 0.5 1 2 3 4 5 6 7 8 9 [mbar/m]
0.01 0.02 0.03 0.05 0.1 0.2 0.3 0.4 0.5
[kPa/m]
Pressure gradient R
1 2
3 4
5 6
1 2
3 4
5 6
r≥5xd
r≥5xd
r≥5xd
Uponor Corporation
www.uponor.com
05_2014_EN
Uponor reserves the right to make changes, without prior notification, to the specification of
incorporated components in line with its policy of continuous improvement and development.