Professional Documents
Culture Documents
SERIES
SMART
®
CONTROLLER R3FC
®
GUARANTEE
1) The controller is guaranteed for a period of 1 year from the date shown on the inside.
2) The guarantee covers the free replacement or repair of components parts that are defective
at origin for manufacturing errors.
3) The guarantee is not valid for damage caused accidentally due to improper use or negligence
and in case of alterations or repair carried out by unauthorized persons.
Design and specifications could be subjected to change without notice.
DECLARATION OF CONFORMITY
REPLACEMENT POLICY
Please fill out a form for Technical a Assistance in “Service” section www.mpelettronica.com
SAFETY INSTRUCTIONS
NOTE Indicates general notes, useful operator tips and operating recommendations
which don’t affect safety and health of the personnel.
NOTE Before using the appliance it is necessary to read attentively the instructions included in this
technical sheet which provides you information about safety installation, use and maintenance.
keep this sheet safely for further information.
GENERAL INSTRUCTIONS
DANGER Before connect the equipment to the mains socket, make sure that the nameplate data match
those of the mains power supply.
Only use this equipment in accordance with the porpouse for which it is designed; i.e. for
regolation of the amplitude of an electromagnetic vibrator feeder. Any other use is to considered
improper, therefore hazardous.
The Manufacturer cannot be held liable for any improper, incorrect or unreasonable use of
the equipment, switch it off and do not tamper with it. If repair is needed, please contact the
Manufacturer’s Technical.
All operations regarding adjustement, measurement and testing when required, must only be
carried out by authorized and qualified personnel.
The Manufacturer shall accept no liability for damage to persons, animals or objects caused by
work on the equipment carried out by unauthorized and unqualifield personnel.
Before switching on the equipment, connect the mains voltage, conforming to the current
regulation, and the vibratory feeder.
WARNING Verifying that the installation has an appropriate ground wiring system.
NOTE
NOTE : Don’t use the apparatus in proximity of subject zones to vibrations, or in acid and humid
working environment
TECHNICAL CHARACTERISTICS
Circuit Type: R3FC Degree Of Protection: Ip55in Box (Only Circuit Ip00)
Supply Voltage: 115 Or 230V ± 10% 50/60Hz Position Of Assemblage: Horizontal Or Vertical.
Potentiometer Of Reg.: 100K Ohm Linear Range Of Relative Humidity: 80% Till to 31°C
Time Ramp: 0,2 Sec. Or 2 Sec. (Selectable) Altitude: Till to 2000 Meters
Input On/Off: Free Contact - Signal Voltage 0/24V Warranty: 1 Year (from date on circuit)
WAVE FORMS
Fig. 1
Fig. 2
Fig. 3
WAVE FORMS
Supply controller (yellow)
Output vibrator (blue)
Frequency 50 Hz - 3000 V/m (Vibrator)
Fig. 1 : Output V/max 216V
Fig. 2 : Output V/medio 160V
Fig. 3 : Output V/min 52V
PARTICULAR INSTRUCTIONS
CAUTION Before give voltage to the controller connect the supply voltage (clamps 2-3 CONN1), verifying
that the installation has an appropriate ground wiring system and the vibrator (clamps
VIBRATOR - CONN 2) of the connector (1-4 ground).
According European Norms EMC the controller have a line-filter with leakage current to ground
less 1 mA.
To adjust intensity of vibration of the vibratory feeder, turn the adjustement knob (potentiometer
100K) on the box.
SHEET
1/1
Sheet : 7
INPUT ON/OFF
DRAFTSMAN
E. PEDRAZZI
FAST RAMP SLOW RAMP
Y1
Date: 02/14
COMPENSATION
Y2
CONN.X
MODULE
Y3
LED "ON"
GREEN
CLOSED
115V
115V
OPEN
230V
CE type
DATE
02/03
CONN.2
Edit: E. Pedrazzi
3,5mm (hole fixing)
VIBRATOR
REV
00
CONN.1
Fuse 5x20 3A F
Rev..: 00
LINE
DTR3FC
CODE
NOTE:
If you use only the electronic circuit (IP00) insert and cable it in a box that
Code: MUMR3FC
could guarantee an excellent safety degree respecting the European
regulation in force and isolate the terminals of the potentiometer with the
rubbers provided.
Decline all responsability for damage caused by improper use of the circuit
Cross Reference: SMART Controllers Series - ISO Series
IP
CE
Box
EMC
Code
Code
Sensor
Amps
0/10V
Photo
Overload
ON/OFF
50/100
60/120
NPN/PNP
ON/OFF
0/20 mA
Slow/Fast
Reg. Volt
50/60 Hz
Min/Max
VoltageV
Time Ramp
Amplitude
Regulation
Free Voltage
Code: MUMR3FC
Dimensions
Signal Voltage
Freq Output Hz
3000-6000 100 x 100 x 50 1
R3FC 115 / 230 3 Man.Pot. 3600-7200 65 2 R3FC
Rev..: 00
R3FSC 115 / 230 4 Man.Pot. 3600-7200 65 115 x 140 x 60 6 R3FSC
3000-6000 4
R5FC 115 / 230 6 Man.Pot. 65 130 x 165 x 70 5 R5FC
3600-7200 140 x 165 x 65
3000-6000
Edit: E. Pedrazzi
RS96C 6 Man.Pot. 65 115 x 140 x 60 6 RS96C
115 / 230 Autom. 3600-7200
Date: 02/14
1 2 3 4 5 6 7 8
Sheet : 8
1 All controllers are stabilized 3 With circuit PRX92-PRX99 inside
2 Other voltage on request 4 With circuit PRX07 inside
M.P. Elettronica srl - Via Torino 62 - 20099 Sesto san Giovanni (Mi) - Italy - Tel: +39 02 2403864 - Fax: +39 02 2400643
®
DIMENSIONS
METALLIC BOX
CIRCUIT
PV R3FCX Z2 STM
PV R3FCX A2 STD
100x100x50
METALLIC BOX
PV R3FCX Z2 SM1
100x100x50
PLASTIC BOX
PV R3FCX Z2 STD
100x100x50
HEADQUARTERS
MP Elettronica srl
via Torino 62
20099 Sesto San Giovanni -MI - ITALY
tel.: +39 (02) 24 03 864
Fax: +39 (02) 24 00 643
www.mpelettronica.com
mp@mpelettronica.com
PRODUCTION UNIT2
MP Elettronica srl
via Torino 80
20099 Sesto San Giovanni -MI - ITALY
tel.: +39 (02) 39 66 23 68
Fax: +39 (02) 24 00 643
www.mpelettronica.com
laboratorio@mpelettronica.com
export@mpelettronica.com
GERMAN +39 339 449 4940
export@mpelettronica.com
FRENCH +39 339 449 4940
mp@mpelettronica.com
ITALIAN +39 393 958 2535