Professional Documents
Culture Documents
T3907-390-01 SG-Ins Exc EN
T3907-390-01 SG-Ins Exc EN
Parametric 2.0
T3907-390-01
Please note that a localized map may not be available in every language and that the map above is
partial and for illustration purposes only.
Before the end of the class, your instructor will review the map corresponding to the course you
are taking. This review, along with instructor recommendations, should give you some ideas for
additional training that corresponds to your role and job functions.
Training Agenda
Day 1
Module 01 ― Introduction to the Creo Parametric Sheetmetal Design Process
Module 02 ― Sheetmetal Model Fundamentals
Module 03 ― Creating Primary Sheetmetal Wall Features
Module 04 ― Creating Secondary Sheetmetal Wall Features
Day 2
Module 05 ― Bending and Unbending Sheetmetal Models
Module 06 ― Modifying Sheetmetal Models
Module 07 ― Sheetmetal Setup and Tools
Module 08 ― Detailing Sheetmetal Designs
Module 09 ― Design Project
Table of Contents
Sheetmetal Design using Creo Parametric 2.0
Design Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
Module 9
Design Project
Scenario
Seals, a company that manufactures staplers, is planning to introduce a new hand stapler. The
stapler has sheetmetal mechanical parts and plastic covers. The design team of your company
has created the product structure and based it on the top-level assembly structure created in Creo
Parametric. You are assigned with the task of designing the four major components - Base, Handle,
Magazine, and Plunger. You will design these parts and review the assembly components with the
top-down design approach in mind.
In this exercise, you will examine the existing HAND_STAPLER.ASM and some of its top-down
design components before creating the necessary geometry in BASE.PRT.
Close Window Erase Not Displayed
Projects\Sheetmetal HAND_STAPLER_SKEL.PRT
6. Open HAND_STAPLER.LAY.
7. Notice the Magazine and the Handle angles
defined as parameters in the layout.
8. Close all windows.
1. Add the configuration option multiple_skeletons_allowed and set it to yes for the Option
value.
Click File > Options and use the Configuration Editor.
Task 3: Create a flat wall to create the lip at the rear of the stapler base.
1. Redefine the PIN.PRT component and apply constraints to it so that it is fully placed.
Make the PIN_AXIS datum axis and FRONT datum plane from the PIN.PRT
Coincident to the PIN_AXIS datum axis and MID_PLANE datum plane from the
HAND_STAPLER_SKEL.PRT, respectively.
Click Show In Assembly Window to view the components in the graphics window.
Add a constraint for each component that makes its FRONT datum plane Coincident to
the MID_PLANE datum plane from the HAND_STAPLER_SKEL.PRT.
3. Save the model and close the window.
1. Review the Bend Order table you just created. Verify that the sequence of bends is correct.
2. Save the model and close the window.
Click File > Prepare > Model Properties.
1. Add the Bend Order table and bend notes to the sheet.
2. Arrange the notes and views in the sheet.
Use Show Model Annotations from the Annotate tab with the flattened view.
PRINTING HISTORY
Document No. Date Description
T3907-390-01 03/29/2012 Initial Printing of:
Sheetmetal Design using Creo Parametric 2.0
Order Number DT-T3907-390-01
Printed in the U.S.A