Professional Documents
Culture Documents
Volvo V50in
Volvo V50in
We hope you will enjoy many years of driving pleasure in your Volvo. In order to increase your enjoyment of the car, we recommend that
The car has been designed for the safety and comfort of you and your you familiarise yourself with the equipment, instructions and mainte-
passengers. Volvo is one of the safest cars in the world. Your Volvo nance information contained in this owner's manual.
has also been designed to satisfy all current safety and environmental
requirements.
Table of contents
00 01 02
00 Introduction 01 Safety 02 Instruments and controls
Important information............................... 10 Seatbelts................................................... 18 Overview, left-hand drive cars.................. 48
Volvo and the environment....................... 13 Airbag system........................................... 21 Overview, right-hand drive cars................ 50
Airbags...................................................... 22 Driver's door control panel....................... 52
Activating/deactivating the airbag*........... 24 Combined instrument panel...................... 53
Side airbags (SIPS bags).......................... 26 Indicator and warning symbols................. 54
Inflatable Curtain (IC)................................ 28 Information display................................... 58
WHIPS....................................................... 29 Electrical socket........................................ 60
When the systems deploy......................... 31 Lighting panel........................................... 62
Crash mode.............................................. 32 Left-hand stalk switch............................... 65
Child safety............................................... 33 Right-hand stalk switch ........................... 68
Cruise control*.......................................... 71
Keypad in the steering wheel* ................. 73
Steering wheel adjustment, hazard warn-
ing flashers................................................ 74
Parking brake............................................ 75
Power windows......................................... 76
Windows, rearview and door mirrors........ 78
Power sunroof* ........................................ 82
Personal preferences................................ 84
HomeLink *.............................................. 87
03 04 05
03 Climate control 04 Interior 05 Locks and alarm
General information on climate control..... 92 Front seats.............................................. 108 Remote control key with key blade......... 126
Manual climate control, AC....................... 94 Interior lighting........................................ 111 Active locks............................................. 129
Electronic climate control, ECC*............... 97 Storage spaces in the passenger com- Keyless drive*.......................................... 130
Air distribution......................................... 100 partment ................................................. 114 Battery in remote control key.................. 133
Fuel-driven engine block heater and pas- Rear seat................................................. 118 Locking and unlocking ........................... 134
senger compartment heater*.................. 101 Cargo area.............................................. 120 Child safety locks.................................... 137
Fuel-driven auxiliary heater* (diesel)....... 104 Alarm* .................................................... 138
06 07 08
06 Starting and driving 07 Wheels and tyres 08 Car care
General.................................................... 144 General.................................................... 190 Cleaning.................................................. 206
Refuelling................................................ 146 Tyre pressure.......................................... 194 Touching up paintwork........................... 210
Alcoguard*.............................................. 150 Warning triangle* and spare wheel * ...... 195 Rustproofing........................................... 211
Starting the engine ................................. 154 Changing wheels.................................... 197
Starting the engine – Flexifuel................. 156 Emergency puncture repair* .................. 199
Keyless drive*.......................................... 158
Manual gearbox...................................... 159
Automatic gearbox.................................. 160
Brake system.......................................... 165
DSTC – Stability and traction control sys-
tem* ........................................................ 167
Park Assist*............................................. 169
BLIS* – Blind Spot Information System . 171
Towing and recovery.............................. 174
Start assistance...................................... 176
Driving with a trailer................................ 177
Towing equipment*................................. 179
Detachable towbar* ............................... 181
Loading................................................... 185
Adjusting headlamp pattern ................... 186
09 10 11
09 Maintenance and service 10 Infotainment system 11 Specifications
Volvo service........................................... 214 General.................................................... 244 Type designation..................................... 278
Self-maintenance.................................... 215 Audio functions....................................... 246 Dimensions and weights......................... 280
Bonnet and engine compartment........... 216 Radio functions....................................... 250 Engine specifications.............................. 283
Oils and fluids......................................... 218 CD functions .......................................... 255 Engine oil................................................ 284
Wiper blades........................................... 224 Menu structure – audio system.............. 258 Fluids and lubricants............................... 286
Battery..................................................... 226 Phone functions*..................................... 259 Fuel......................................................... 289
Replacing bulbs...................................... 228 Menu structure – phone*......................... 266 Wheel and tyres, dimensions and pres-
Fuses...................................................... 234 Bluetooth handsfree*.............................. 269 sure ........................................................ 290
Electrical system..................................... 292
Type approval......................................... 294
Symbols in the display............................ 295
12
12 Alphabetical Index
Alphabetical Index.................................. 298
8
Table of contents
9
Introduction
Important information
Reading the Owner's Manual In the event of uncertainty over what is stand- lighted in the owner's manual by means of the
ard or an option/accessory, contact a Volvo text being slightly larger and printed in grey.
Introduction dealer. Examples of this are in menu texts and mes-
A good way of getting to know your new car is sage texts on the information display (e.g.
to read the owner's manual, ideally before your Special texts AUDIO SETTINGS).
first journey. This will give you the opportunity
to familiarise yourself with new functions, to WARNING Decals
see how best to handle the car in different sit- The car contains different types of decal which
Warning texts advise of a risk of personal
uations, and to make the best use of all the are designed to convey important information
injury.
car's features. Please pay attention to the in a simple and clear manner. The decals in the
safety instructions contained in the manual. car have the following descending degree of
The specifications, design features and illus- IMPORTANT importance for the warning/information.
trations in this owner's manual are not binding. Important texts advise of a risk of material Warning for personal injury
We reserve the right to make modifications damage.
without prior notice.
© Volvo Car Corporation NOTE
Option NOTE texts give advice or tips that facilitate
the use of features and functions for exam-
All types of option/accessory are marked with
ple.
an asterisk*.
In addition to standard equipment, this manual Footnote
also describes options (factory fitted equip-
There is footnote information in the owner's
ment) and certain accessories (retrofitted extra
manual that is located at the bottom of the
equipment).
page. This information is an addition to the text
The equipment described in the owner's man- that it refers to via a number. If the footnote
ual is not available in all cars - they have dif- refers to text in a table then letters are used G031590
Important information
G031593
bered and are used to illustrate a move-
ment.
G031592
11
Introduction
Important information
12
Introduction
G000000
Environmental care is one of Volvo Car Corpo- Fuel consumption many cases the exhaust emissions are well
ration's core values which influence all opera- Volvo cars have competitive fuel consumption below the applicable standards.
tions. We also believe that our customers share in each of their respective classes. Lower fuel
our consideration for the environment. consumption generally results in lower emis- Clean air in the passenger compartment
sion of the greenhouse gas, carbon dioxide. A passenger compartment filter prevents dust
Your Volvo complies with strict international and pollen from entering the passenger com-
environmental standards and is also manufac- It is possible for the driver to influence fuel con- partment via the air intake.
tured in one of the cleanest and most resource- sumption. For more information read under the
efficient plants in the world. Volvo Car Corpo- heading, Reducing environmental impact. A sophisticated air quality system, IAQS* (Inte-
ration has global ISO certification, which rior Air Quality System) ensures that the incom-
includes the environmental standard ISO Efficient emission control ing air is cleaner than the air in the traffic out-
14001 covering all factories and several of our Your Volvo is manufactured following the con- side.
other units. We also set requirements for our cept "Clean inside and out" – a concept that The system consists of an electronic sensor
partners so that they work systematically with encompasses a clean interior environment as and a carbon filter. The incoming air is moni-
environmental issues. well as highly efficient emission control. In tored continuously and if there is an increase in
the level of certain unhealthy gases such as tem. We make clear demands regarding the • Always dispose of environmentally hazar-
carbon monoxide then the air intake is closed. way in which our workshops are designed in dous waste, such as batteries and oils, in
Such a situation may arise in heavy traffic, order to prevent spills and discharges into the an environmentally safe manner. Consult a
queues and tunnels for example. environment. Our workshop staff have the workshop in the event of uncertainty about
knowledge and the tools required to guarantee how this type of waste should be discarded
The entry of nitrous oxides, ground-level ozone - an authorised Volvo workshop is recom-
good environmental care.
and hydrocarbons is prevented by the carbon mended.
filter. Reducing environmental impact Following this advice can save money, the
You can easily help reduce environmental planet's resources are saved, and the car's
Textile standard
impact - here are a few tips: durability is extended. For more information
The interior of a Volvo is designed to be plea-
sant and comfortable, even for people with • Avoid letting the engine idle - switch off the and further advice, see the pages 144 and
contact allergies and for asthma sufferers. engine when stationary for longer periods. 289.
Extreme attention has been given to choosing Pay attention to local regulations.
Recycling
environmentally-compatible materials. This • Drive economically - think ahead. As a part of Volvo's environmental work, it is
means that they also fulfil the requirements in
• Perform service and maintenance in important that the car is recycled in an envi-
the Oeko-Tex 100 standard1, a major advance accordance with the owner's manual's ronmentally sound manner. Almost all of the
towards a healthier passenger compartment instructions - follow the Service and War- car can be recycled. The last owner of the car
environment. ranty Booklet's recommended intervals. is therefore requested to contact a dealer for
Oeko-Tex certification covers seatbelts, car- • If the car is equipped with an engine block referral to a certified/approved recycling
pets and fabrics for example. The leather in the heater*, use it before starting from cold - it facility.
upholstery undergoes chromium-free tanning improves starting capacity and reduces
and fulfils the certification requirements. wear in cold weather and the engine rea-
ches normal operating temperature more The owner's manual and the
Volvo workshops and the environment quickly, which lowers consumption and environment
Regular maintenance creates the conditions reduces emissions. The FSC symbol shows that the paper pulp in
for a long service life and low fuel consumption this publication comes from FSC certified for-
• High speed increases consumption con-
for your car. In this way you contribute to a siderably due to increased wind resistance ests or other controlled sources.
cleaner environment. When Volvo's workshops - a doubling of speed increases wind resis-
are entrusted with the service and mainte- tance 4 times.
nance of your car it becomes part of our sys-
15
Seatbelts................................................................................................. 18
Airbag system......................................................................................... 21
Airbags.................................................................................................... 22
Activating/deactivating the airbag*......................................................... 24
Side airbags (SIPS bags)........................................................................ 26
Inflatable Curtain (IC).............................................................................. 28
WHIPS..................................................................................................... 29
When the systems deploy....................................................................... 31
Crash mode............................................................................................ 32
Child safety............................................................................................. 33
01 Seatbelts
• do not use clips or anything else that can appear damaged. The seatbelt must also be
prevent the seatbelt from fitting properly
replaced if it shows signs of wear or dam-
Tensioning the hip strap. The belt must be posi- • ensure that the seatbelt is not twisted or age. The new seatbelt must be type-
tioned low down. caught on anything approved and designed for installation at
the same location as the replaced seatbelt.
Heavy braking can have serious consequences • the hip strap must be positioned low down
if the seatbelts are not used. Ensure that all (not over the abdomen)
passengers use their seatbelts. It is important • tension the hip strap over the lap by pulling
that the seatbelt lies against the body so it can the diagonal shoulder belt as illustrated.
provide maximum protection. Do not lean the
backrest too far back. The seatbelt is designed WARNING
to protect in a normal seating position.
The seatbelts and airbags interact. If a seat-
Putting on a seatbelt belt is not used or is used incorrectly, this
may diminish the protection provided by the
Pull the seatbelt out slowly and secure it by airbag in the event of a collision.
pressing the buckle into the lock. A loud
"click" indicates that the seatbelt has
locked.
18
01 Safety
Seatbelts 01
Seatbelts and pregnancy such that they can easily maintain control of the Child seats are not covered by the seatbelt
vehicle as they drive (which means that they reminder system.
must be able to easily operate the foot pedals
and steering wheel). They should strive to posi- Rear seat
tion the seat with as large a distance as possi- The seatbelt reminder in the rear seat has two
ble between their abdomen and the steering subfunctions:
wheel. • Provides information on which seatbelts
are being used in the rear seat. A message
Seatbelt reminder appears in the information display when
the seatbelts are in use, or if one of the rear
doors has been opened. The message is
cleared automatically after driving for
G020105
approximately 30 seconds or after press-
ing the indicator stalk's READ button.
• Provides a warning if one of the rear seat-
belts is unfastened during a journey. This
The seatbelt should always be worn during warning takes the form of a message on
pregnancy. But it is crucial that it be worn in the the information display along with the
correct way. The diagonal section of the seat- audio/visual signal. The warning ceases
belt should wrap over the shoulder then be when the seatbelt is re-fastened or when
routed between the breasts and to the side of acknowledged manually by pressing the
the abdomen. READ button.
G018084
The message on the information display show-
The lap section of the seatbelt should lay flat
ing which seatbelts are in use is always avail-
over the thighs and as low as possible under
Unbelted occupants will be reminded to fasten able. Press the READ button to see stored
the abdomen. – It must never be allowed to ride
their seatbelts by means of an audio and visual messages.
upward. Remove the slack from the seatbelt
and ensure that it fits as close to the body as reminder. The audio reminder is speed Certain markets
possible. In addition, check that there are no dependent, and in some cases time depend- An audio signal and indicator lamp remind the
twists in the seatbelt. ent. The visual reminder is located in the roof driver if not wearing a seatbelt to use one. At
console and the combined instrument panel. low speed, the audio reminder will sound for
As a pregnancy progresses, pregnant drivers
should adjust their seats and steering wheel the first 6 seconds.
``
19
01 Safety
01 Seatbelts
Seatbelt tensioner
The front seatbelts and the two for the outer
rear seats are equipped with seatbelt tension-
ers. A mechanism in the seatbelt tensioner
tightens the seatbelt in the event of a suffi-
ciently violent collision. The seatbelt then pro-
vides more effective restraint for occupants.
WARNING
Never insert the tongue of the passenger's
seatbelt into the buckle on the driver's side.
Always insert the tongue of the seatbelt into
the buckle on the correct side. Do not make
any damages on seatbelts nor insert any
foreign objects into a buckle. The seatbelts
and buckles would then possibly not func-
tion as intended in the event of a collision.
There is a risk of serous injury.
20
01 Safety
Airbag system 01
WARNING
If the warning symbol for the airbag system
remains illuminated or illuminates while driv-
ing, it means that the airbag system does
not have full functionality. The symbol indi-
The warning symbol in the combined instru- cates a fault in the seatbelt tensioner sys-
ment panel illuminates when the remote con- tem, SIPS, SRS or the IC system. Volvo rec-
trol key is turned to key position I, II or III. The ommends that you contact an authorised
Volvo workshop immediately.
symbol goes out after approx. 6 seconds pro-
vided the airbag system is fault-free.
21
01 Safety
01 Airbags
G020110
cushion the impact, the airbag deflates when
compressed. When this occurs, smoke
escapes into the car. This is completely nor- SRS system, right-hand drive
mal. The entire process, including inflation and
deflation of the airbag, takes place within
tenths of a second.
22
01 Safety
Airbags 01
23
01 Safety
Messages
G018083
Indicator showing that the passenger airbag is
2 activated.
A warning symbol in the roof panel indicates
that the airbag for the front passenger seat is
activated (see preceding illustration).
G018082
G025315
seat covers may impede the operation
G020118
26
01 Safety
G025316
27
01 Safety
Properties WARNING
Never hang or attach heavy items onto the
handles in the roof. The hook is only
designed for light clothing (not for solid
objects such as umbrellas for example).
Do not screw or install anything onto the
car's headlining, door pillars or side panels.
This could compromise the intended pro-
tection. Volvo recommends that you only
ever use Volvo genuine parts that are
approved for placement in these areas.
WARNING
G019985
28
01 Safety
WHIPS 01
G020347
The whiplash protection system (WHIPS) con- Properties of the seat WHIPS system and child seats/booster
sists of energy absorbing backrests and spe- When the WHIPS system is deployed, the front cushions
cially designed head restraints for the front seat backrests are lowered backward to alter The protection provided by the car to children
seats. The system is actuated by a rear-end the seating position of the driver and front seat seated in a child seat or on a booster cushion
collision, where the angle and speed of the col- passenger. This reduces the risk of whiplash is not diminished by the WHIPS system.
lision, and the nature of the colliding vehicle all injury.
have an influence. Correct seating position
WARNING For the best possible protection, the driver and
WARNING front seat passenger should sit in the centre of
Never modify or repair the seat or WHIPS the seat with as little space as possible
The WHIPS system is a supplement to the system yourself. Volvo recommends that between the head and the head restraint.
seatbelts. Always use a seatbelt. you contact an authorised Volvo workshop.
``
29
01 Safety
01 WHIPS
G020126
collision.
G020125
30
01 Safety
31
01 Safety
01 Crash mode
Driving after a collision Firstly, remove the remote control key and then WARNING
reinsert it. The car's electronics will then try to
reset themselves to normal mode. Then try to Never, under any circumstances, attempt to
restart the car if it smells of fuel when the
start the car. If CRASH MODE SEE
CRASH MODE SEE MANUAL message is
MANUAL is still shown on the display then the displayed. Leave the car at once.
car must not be driven or towed. Even if the car
appears to be driveable, hidden damage may
make the car impossible to control once mov- WARNING
ing. If the car is in crash mode it must not be
towed. It must be transported from its loca-
Moving the car tion. Volvo recommends that you have it
If NORMAL MODE is shown after CRASH conveyed to an authorised Volvo workshop.
MODE SEE MANUAL has been reset, the car
can be moved carefully out of a dangerous
G029042
32
01 Safety
Child safety 01
Children should sit comfortably and NOTE Do not attach the straps for the child seat to
safely the horizontal adjustment bar, springs, rails or
In the event of questions when fitting child beams under the seat. Sharp edges can dam-
Volvo recommends that children travel in rear- safety products, contact the manufacturer
facing child seats until as late an age as pos- age the straps.
for clearer instructions.
sible, at least until 3-4 years of age, and then Look in the installation instructions for the child
front-facing booster cushions/child seats until seat for the correct fitting.
up to 10 years of age. Child seats
Location of child seats
The position of a child in the car and the choice
You may place:
of equipment are dictated by the child's weight
and size, for more information, see page 35. • a child seat/booster cushion on the front
passenger seat, provided the passenger
NOTE airbag is not activated1.
G020128
to sit on the knee of a passenger.
Volvo has child safety equipment (child seats,
booster cushions & attachment devices) which Child seats and airbags are not compatible.
is designed for your particular car. Using Vol-
vo's child safety equipment provides you with NOTE
optimum conditions for your child to travel
safely in the car. Furthermore, the child safety When using child safety products it is
important to read the installation instruc-
equipment fits and is easy to use. tions included with the product.
33
01 Safety
01 Child safety
34
01 Safety
Child safety 01
Volvo infant seat (Volvo Infant Seat) - Volvo infant seat (Volvo Infant Seat) - Volvo infant seat (Volvo Infant Seat) -
rear-facing child seat, secured with the rear-facing child seat, secured with the rear-facing child seat, secured with the
car's seatbelt car's seatbelt car's seatbelt.
U: Type approval: E1 04301146 U: Type approval: E1 04301146 U: Type approval: E1 03301146
Rear-facing child seat (Child Seat) - rear- Rear-facing child seat (Child Seat) - rear- Rear-facing child seat (Child Seat) - rear-
facing child seat, secured with the car's facing child seat, secured with the car's facing child seat, secured with the car's
seatbelt and straps. Use a protective seatbelt, straps and support legs. seatbelt, straps and support legs.
cushion between the child seat and the
L: Type approval: E5 03135 L: Type approval: E5 03135
dashboard.
L: Type approval: E5 03135
U: Child seats which are universally U: Child seats which are universally U: Child seats which are universally
approved. approved. approved.
3 With regard to other child seats the car should be included in the manufacturer's enclosed list of vehicles or be universally approved in accordance with the ECE R44 legal requirement.
``
01 Child safety
Rear-facing child seat (Child Seat) - rear- Rear-facing child seat (Child Seat) - rear- Rear-facing child seat (Child Seat) - rear-
facing child seat, secured with the car's facing child seat, secured with the car's facing child seat, secured with the car's
seatbelt and straps. Use a protective seatbelt, straps and support legs. seatbelt, straps and support legs.
cushion between the child seat and the
L: Type approval: E5 03135 L: Type approval: E5 03135
dashboard.
L: Type approval: E5 03135
Britax Fixway – rear-facing child seat, Britax Fixway – rear-facing child seat,
secured with the ISOFIX fixture system secured with the ISOFIX fixture system
and straps. This fitting requires an ISOFIX and straps.
bracket* for correct installation.
L: Type approval: E5 03171
L: Type approval: E5 03171
U: Child seats which are universally U: Child seats which are universally U: Child seats which are universally
approved. approved. approved.
Child safety 01
Volvo rear-facing/turnable child seat Volvo rear-facing/turnable child seat Volvo rear-facing/turnable child seat
(Volvo Convertible Child Seat) - front-fac- (Volvo Convertible Child Seat) - front-fac- (Volvo Convertible Child Seat) - front-fac-
ing child seat, secured with the car's ing child seat, secured with the car's ing child seat, secured with the car's
seatbelt. seatbelt. seatbelt.
L: Type approval: E5 04191 L: Type approval: E5 04191 L: Type approval: E5 04191
``
37
01 Safety
01 Child safety
Booster cushion with and without back- Booster cushion with and without back- Booster cushion with and without back-
rest (Booster Cushion with and without rest (Booster Cushion with and without rest (Booster Cushion with and without
backrest). backrest). backrest).
UF: Type approval: E5 03139 UF: Type approval: E5 03139 UF: Type approval: E5 03139
L: Suitable for specific child seats. These child seats may be intended for use in a special car model, limited or semi-universal categories.
U: Suitable for universally approved child seats in this weight class.
UF: Suitable for front-facing universally approved child seats in this weight class.
B: Built-in child seats approved for this weight class.
A For information on activated/deactivated airbag, see page 24.
38
01 Safety
Child safety 01
G020808
Pull that handle to raise the booster cush-
ion.
Grasp the cushion with both hands and
push it backwards.
G015013
01 Child safety
WARNING Lowering the booster cushion Child safety locks, rear doors
The controls for operating the rear door power
Repair or replacement should only be per-
formed by a workshop. Volvo recommends windows and the rear door opening handles
that you contact an authorised Volvo work- can be blocked from opening from the inside.
shop. Do not make any modifications or For more information see page 137.
additions to the booster cushion yourself.
If an integrated booster cushion has been ISOFIX fixture system for child seats
subjected to a major load, such as in con-
junction with a collision, the entire booster
cushion must be replaced. Even if the
booster cushion appears to be undamaged,
it may not afford the same level of protec-
tion. The booster cushion must also be
G014507
replaced if it is heavily worn.
G015268
NOTE
Remember to stow away the booster cush-
ion before lowering the rear seat backrest. Mounting points for the ISOFIX fixture system
are concealed behind the lower section of the
rear seat backrest, in the outer seats.
The location of the mounting points is indicated
by symbols in the backrest upholstery (see
illustration above).
40
01 Safety
Child safety 01
Press the seat cushion down to access the Size Description Size Description
mounting points.
class class
NOTE A Full size, front-facing child F Transverse infant seat, left-
seat hand
The ISOFIX fixture system is an accessory
for the passenger seat. B Reduced size (alt. 1), front- G Transverse infant seat, right-
facing child seat hand
Always follow the manufacturer's installation
instructions when connecting a child seat to B1 Reduced size (alt.2), front-
facing child seat WARNING
the ISOFIX mounting points.
Never place a child in the passenger seat if
Size classes C Full size, rear-facing child
the car is equipped with an activated airbag.
Child seats are in different sizes – cars are in seat
different sizes. This means that not all child D Reduced size, rear-facing
seats are suitable for all seats in all car models. NOTE
child seat
Consequently, there is a size classification for If an ISOFIX child seat has no size classifi-
E Rear-facing infant seat cation then the car model must be included
child seats using the ISOFIX fixture system in
on the child seat's vehicle list.
order to assist users in choosing the correct
child seat (see the following table).
NOTE
Volvo recommends that you contact an
authorised Volvo dealer for recommenda-
tions about which ISOFIX child seats Volvo
recommends.
``
41
01 Safety
01 Child safety
G X X
D X OK
(IL)
C X OK
(IL)
C X OK
(IL)
42
01 Safety
Child safety 01
Type of child seat Weight Size class Passenger seats for ISOFIX installation of child seats
Front seat Outer rear seat
Front-facing child seat 9-18 kg B X OKA
(IUF)
B1 X OKA
(IUF)
A X OKA
(IUF)
X: The ISOFIX position is not suitable for ISOFIX child seats in this weight class and/or size class.
IL: Suitable for specific ISOFIX child seats. These child seats may be intended for use in a special car model, limited or semi-universal categories.
IUF: Suitable for front-facing ISOFIX child seats that are universally approved in this weight class.
A Volvo recommends rear-facing child seats for this group.
``
43
01 Safety
01 Child safety
NOTE
For cars equipped with a cargo area cover
over the cargo area, this must be removed
before a child seat can be fitted in the
mounting points.
G029703
44
01 Safety
01
45
Overview, left-hand drive cars................................................................ 48
Overview, right-hand drive cars.............................................................. 50
Driver's door control panel..................................................................... 52
Combined instrument panel.................................................................... 53
Indicator and warning symbols............................................................... 54
Information display.................................................................................. 58
Electrical socket...................................................................................... 60
Lighting panel.......................................................................................... 62
Left-hand stalk switch............................................................................. 65
Right-hand stalk switch ......................................................................... 68
Cruise control*........................................................................................ 71
Keypad in the steering wheel* ............................................................... 73
Steering wheel adjustment, hazard warning flashers............................. 74
Parking brake.......................................................................................... 75
Power windows....................................................................................... 76
Windows, rearview and door mirrors...................................................... 78
Power sunroof* ...................................................................................... 82
Personal preferences.............................................................................. 84
HomeLink *............................................................................................ 87
02
G019488
48
02 Instruments and controls
49
02 Instruments and controls
02
G028204
50
02 Instruments and controls
51
02 Instruments and controls
02
G029046
Speedometer. Tachometer – Indicates engine speed in Button for trip meter – Used to measure
thousands of revolutions per minute (rpm). short distances. Short presses on the but-
Direction indicators, left. ton switches between the two trip meters
Indicator and warning symbols.
Warning symbol. T1 and T2. A long press (more than 2 sec-
Fuel gauge, see also trip computer, pag onds) resets an active trip meter to zero.
Information display – Shows information or e 66. Temperature gauge - Used for the engine
warning messages, outside temperature Main beam indicator. cooling system. A message will appear on
and clock. When the outside temperature
the display if the temperature becomes too
is between +2 °C to -5 °C a snowflake illu- Display – Display for automatic gear posi-
high and the gauge goes into the red zone.
minates on the display. This warns of icy tion, rain sensor, odometer, trip meter and
Bear in mind that extra lights placed in front
roads. The outside temperature gauge cruise control.
of the air intake, for example, reduce the
may show a slightly high reading after the Also shows gear shift indicator (GSI) and cooling capacity at high outside tempera-
car has been stationary. gear positions in the 1.6D DRIVe model, tures and high engine loads.
Information symbol. see page 159.
Indicator and warning symbols.
Direction indicator, right.
53
02 Instruments and controls
Functionality check, symbols Symbols in the centre of the instrument When the symbol illuminates:
All indicator and warning symbols1 illuminate panel 1. Stop in a safe manner. Do not drive the car
02
when the remote control key is turned to posi- further.
tion II before starting. This is to check that the
2. Read the information on the information
symbols are working. When the engine starts,
display. Implement the action in accord-
all the symbols should go out except the hand-
ance with the message in the display. Clear
brake symbol, which only goes out when the
the message using READ.
brake is disengaged.
The yellow information symbol illu-
If the engine does not start within
minates and a text appears on the
five seconds, all symbols extin-
information display. The message
guish except the symbols for a
fault in the car's emissions system text is cleared using the READ but-
and for low oil pressure. Certain ton, see page 58, or disappears
symbols may have no function, automatically after a period of time (time
G030755
depending on the car's specifica- depending on which function is indicated).
tions. The yellow information symbol can also illumi-
nate in conjunction with other symbols.
The red warning symbol illumi-
nates when a fault has been indi-
cated which could affect the safety NOTE
and/or driveability of the car. An When a service message is shown, the sym-
explanatory text is shown on the bol and message are cleared using the
information display at the same time. The sym- READ button, or disappear automatically
bol remains visible until the fault has been rec- after a time.
tified but the text message can be cleared with
the READ button, see page 58. The warning
symbol can also illuminate in conjunction with
other symbols.
1 For certain engine variants, the symbol for low oil pressure is not used. Warnings are given via display text, see page 58.
54
02 Instruments and controls
Indicator symbols – left-hand side Emissions system Stability system STC or DSTC*
If the symbol illuminates then it For information on the system's
may be due to a fault in the car's functions and symbols, see 02
emissions system. Volvo recom- page 167.
mends that you seek assistance
from an authorised Volvo work-
shop for inspection. Engine preheater (diesel)
This symbol illuminates during
ABS fault engine preheating. Preheating
If this symbol illuminates then the occurs when the temperature is
system is not working. The car's below -2 °C. The car can be started
regular brake system continues to once the symbol goes out.
work, but without the ABS func-
tion.
G029048
``
Indicator symbols – right-hand side Indicator symbol for trailer Low oil pressure2
This symbol flashes when the If this symbol illuminates during
02 direction indicators are used and driving then the engine's oil pres-
the trailer is connected. If the sym- sure is too low. Stop the engine
bol does not flash then one of the immediately and check the engine
lamps on the trailer or the car is oil level, top up if necessary. If the
faulty. symbol illuminates and the oil level is normal
Volvo recommends that you contact an author-
Parking brake applied ised Volvo workshop.
The symbol illuminates when the
parking brake is applied. Always Seatbelt reminder
pull the parking brake lever to the This symbol illuminates if someone
G029049 end position. in a front seat has not put on their
seatbelt or if someone in a rear
seat has taken off their seatbelt.
NOTE
Indicator symbol for trailer The symbol illuminates irrespective of how Alternator not charging
hard the parking brake is applied. If this symbol illuminates while
Parking brake applied
driving, a fault has occurred in the
Airbags – SRS Airbags – SRS electrical system. Volvo recom-
If this symbol remains illuminated mends that you visit an authorised
Low oil pressure or illuminates while driving, it Volvo workshop.
Seatbelt reminder means a fault has been detected in
the seatbelt buckle, SRS, SIPS or Fault in brake system
Alternator not charging IC system. Volvo recommends that If this symbol illuminates, the brake
drive directly to an authorised Volvo workshop fluid level may be too low.
Fault in brake system for inspection.
2 For certain engine variants, the symbol for low oil pressure is not used. Warnings are given via display text, see page 58.
56
02 Instruments and controls
Stop the car in a safe place and check the have the brake system checked. Volvo rec- Low speed
level in the brake fluid reservoir, see ommends that you seek assistance from If the car moves at a speed less
page 223. If the reservoir level is below an authorised Volvo workshop. than 5 km/h, the information sym- 02
MIN then the car should not be driven fur- bol illuminates and DRIVER
6. If the level in the reservoir is below MIN
ther. Volvo recommends that the car is DOOR OPEN, PASSENGER
then the car should not be driven any fur-
transported to an authorised Volvo work- DOOR OPEN,LEFT REAR
ther. Have the car transported to a work-
shop to have the brake system checked. DOOR OPEN, BONNET OPEN or RIGHT
shop to have the brake system checked.
If the BRAKE and ABS symbols Volvo recommends that you seek assis- REAR DOOR OPEN is shown on the display.
illuminate at the same time, there tance from an authorised Volvo workshop. Stop the car safely as soon as possible and
may be a fault in the brake force close the door or bonnet.
distribution system. WARNING High speed
If the car is moving faster than
If the BRAKE and ABS symbols are lit at the
same time, there is a risk that the rear end 10 km/h, the symbol illuminates
will skid during heavy braking. and one of the texts indicated in
the preceding paragraph appears
on the display.
1. Stop the car in a safe place and turn off the Reminder – doors not closed Tailgate reminder
engine. If one of the doors, the bonnet3 or the tailgate If the tailgate is open, this informa-
2. Restart the engine. is not properly closed, the driver will be tion symbol will illuminate and
reminded of this. TAILGATE OPEN will appear on
3. If both symbols extinguish, continue driv-
the display.
ing.
4. If the symbols remain illuminated, check
the level in the brake fluid reservoir, see
page 223.
5. If the brake fluid level is normal but the
symbols are still illuminated, the car can be
driven, with great care, to a workshop to
57
02 Instruments and controls
Information display
58
02 Instruments and controls
Information display
59
02 Instruments and controls
Electrical socket
NOTE
Optional equipment and accessories - e.g.
TV screens, music players and mobile
phones - which are connected to one of the
passenger compartment's 12V electrical
sockets, could be activated by the climate
control system, even when the remote con-
trol key has been removed or when the car
G029082
is locked, for example, when the parking
G019621
Electrical socket
WARNING
Always leave the plug in the socket when 02
the socket is not in use.
61
02 Instruments and controls
Lighting panel
Lighting panel
The lamps are switched off automatically when Fog lamps Fuel filler flap
the remote control key is turned to position I or Press button (5) to open the fuel filler flap when
0. 02
NOTE the car is unlocked, see page 134.
Regulations for use of fog lamps vary from
Instrument lighting country to country. Active Xenon headlamps*
The instrument lighting is switched on when
the remote control key is in position II and the Front fog lamps*
headlamp control (2) is in one of the end posi- The front fog lamps can be switched on along
tions. The lighting is automatically dimmed with the headlamps or the position lamps/park-
during the day and can be controlled manually ing lamps.
at night.
Press the button (4).
Roll the control up or down (3) for brighter
or dimmer lighting. The light in the button (4) illuminates when the
front fog lamps are switched on.
G026507
clock and outside temperature gauge, these the headlamps or the front fog lamps.
illuminate when the car is unlocked and when Press the button (6).
the remote control key is removed from the
ignition switch. The displays extinguish when The rear fog lamp indicator symbol on the com- Lighting panel, for active Xenon headlamps
the car is locked. bined instrument panel and the light in the but- If the car is equipped with active Xenon head-
ton (6) illuminate when the rear fog lamp is lamps (Active Bending Lights, ABL) the light
switched on. from the headlamps follows the steering wheel
movement in order to provide maximum light-
ing in bends and junctions and so provide
increased safety.
``
Lighting panel
G020789
Brake light
The brake light automatically comes on during
braking. For information on the Emergency
brake lights and automatic hazard warning
flashers, see page 166.
64
02 Instruments and controls
Stalk switch positions Direction indicators Switching, main and dipped beam
The remote control key must be in position II
Continuous flash sequence 02
and the headlamp control in end position, see
Move the stalk switch up or down to
page 62, for main beam to be switched on.
end position (2).
2
Activating main beam:
The stalk switch remains in its end position and
1 is moved back manually, or automatically by Move the stalk switch towards the steering
steering wheel movement. wheel to the end position (4) and release.
3
Deactivating main beam:
Short flash sequence
4
Move the stalk switch up or down to Move the stalk switch towards the steering
position (1) and release. wheel to position (3) and release.
1
The direction indicators flash three times and
G026380
2 the stalk switch returns to its home position. Home safe lighting
Some of the exterior lighting can be kept
Short flash sequence, direction indicators Main beam flash switched on to work as home safe lighting after
the car has been locked. The standard delay is
Move the stalk switch gently towards the
Continuous flash sequence, direction indi-
steering wheel to position (3). 301 seconds, but can be changed to 60 or 90
cators seconds, see page 85.
Main beam flash and switching from main Main beam comes on until the stalk switch is
released. Main beam flash only works when the 1. Remove the remote control key from the
to dipped beam ignition switch.
remote control key is inserted in the ignition
Home safe lighting and switching from switch. 2. Move the stalk switch towards the steering
dipped to main beam wheel to the end position (4) and release.
3. Get out of the car and lock the door.
1 Factory settings.
``
65
02 Instruments and controls
2 No function in cars without trip computer, fuel-driven parking heater as well as stability and traction control system.
3 Certain markets.
4 Only applies to diesel cars with particle filter.
3 Certain markets.
67
02 Instruments and controls
Rear window wiper and washer wiping. If the rear window wiper is already on extra sweep is made when the thumbwheel is
at normal speed, no change is made. turned upwards).
02
The function for intermittent wiping for reverse On/Off
can be deactivated. Volvo recommends that When activating the rain sensor, the remote
you contact an authorised Volvo workshop. control key must be in position I or II and the
windscreen wiper stalk switch must be in posi-
0
Rain sensor* tion 0 (not activated).
Activating the rain sensor:
Press the button (B), see page 68. A display
symbol shows that the rain sensor is
G021418 active.
To turn the rain sensor off, either:
1. Press button (B)
Move the stalk switch forward to start rear win- 2. Press the stalk switch downward to
dow washing and wiping. The wiper blade another wiper program. If the stalk switch
makes several extra sweeps once washing has is raised, the rain sensor will remain active,
finished. The button at the end of the stalk the wipers make an extra sweep and then
G029053
switch has three positions: return to rain sensor mode when the stalk
is released to position 0 (not activated), see
Intermittent wiping: Depress the top of the
page 68.
button.
The rain sensor automatically activates the The rain sensor is automatically deactivated
Neutral position: Function deactivated. windscreen wipers based on how much water when the remote control key is removed from
Constant speed: Depress the bottom of it detects on the windscreen. The sensitivity of the ignition switch or five minutes after the igni-
the button. the rain sensor can be adjusted using the tion is switched off.
thumbwheel (C), see page 68.
Wiper – reversing Turn the thumbwheel upwards for higher sen-
Engaging reverse gear while the windscreen sitivity and downwards for lower sensitivity, (an
wipers are on initiates intermittent rear window
``
IMPORTANT
02 At an automatic car wash: Deactivate the
rain sensor by pressing the button (B) while
the remote control key is in position I or II.
Otherwise, the windscreen wipers could
start swiping and become damaged.
Thumbwheel
Use the thumbwheel to adjust the frequency of
wiper sweeps when intermittent wiping is
selected, or the sensitivity to rain when the rain
sensor is selected.
70
02 Instruments and controls
Cruise control*
Temporary disengagement
Press 0 to disengage the cruise control
temporarily. CRUISE will be shown on the
combined instrument panel. The speed set
G029054
G020141
Cruise control*
Disengaging
Press CRUISE to disengage the cruise
control. CRUISE ON clears on the com-
bined instrument panel.
G020143
G020144
steering wheel.
2. Adjust the steering wheel to the position
that suits you best. Use the hazard warning flashers (all direction
3. Push back the lever to fix the steering indicators flash) when the car is stopped where
wheel in place. If the lever is stiff, press the it could be a traffic hazard or obstruction. Press
steering wheel lightly at the same time as the button to activate the function.
you push the lever back. A sufficiently violent collision or heavy braking
activates the hazard warning flashers automat-
ically, see page 166. The function can be
deactivated with the button.
74
02 Instruments and controls
Parking brake
Parking on a hill
If the car is parked facing uphill; turn the wheels
away from the kerb.
The lever is located between the front seats. If the car is parked facing downhill; turn the
wheels towards the kerb.
NOTE
WARNING
The warning lamp symbol in the combined
instrument panel illuminates irrespective of Get into the habit of always applying the
how hard the parking brake is applied. parking brake when parking on a slope -
leaving the car in gear, or in P if it has auto-
matic transmission, is not sufficient to hold
WARNING the car in all situation.
Make sure that children, other passengers
or objects are not in danger of becoming How to release the parking brake
trapped in any way when the parking brake 1. Press the foot brake pedal down firmly.
is applied or released by the driver.
2. Pull the parking brake lever up slightly,
press the button, release the parking brake
lever and release the button.
75
02 Instruments and controls
Power windows
76
02 Instruments and controls
Power windows
77
02 Instruments and controls
Interior rearview mirror Interior rearview mirror with compass* Calibrating the compass
02
G031045
G031043
Bright light from behind could be reflected in The upper right-hand corner of the rearview The earth is divided into 15 magnetic zones.
the rearview mirror and dazzle the driver. Use mirror has an integrated display that shows the The compass is set for the geographical area
dimming when disturbed by light from behind. compass direction in which the front of the car to which the car was delivered. The compass
is pointing. Eight different directions are shown should be calibrated if the car is moved across
Dipping with English abbreviations: N (north), NE (north several magnetic zones.
Control for dimming east), E (east), SE (south east), S (south), SW 1. Stop the car in a wide open area with the
Normal position (south west), W (west) and NW (north west). engine running at idling speed.
Dimmed position. 2. Press and hold button (1) for at least 6 sec-
onds. Following which, the character C is
Automatic dimming* shown (the button is concealed so use a
Bright light from behind is automatically paper clip for example to press it in).
dimmed by the rearview mirror. The control (1) 3. Press and hold button (1) for at least 3 sec-
is not available in mirrors with automatic dim- onds. The number for the current magnetic
ming. zone is displayed.
G020151
G020153
is shown on the display, which indicates
that the calibration is complete.
Magnetic zones, Asia. Magnetic zones, Australia.
G020150
G020152
G020154
Magnetic zones, Europe.
Magnetic zones, South America. Magnetic zones, Africa.
``
79
02 Instruments and controls
IMPORTANT
Do not use a metal ice scraper to remove ice
from the windows. The water and dirt-repel-
lent coating could be damaged.
Power sunroof*
Sliding position
Automatic operation
Pull the control past the point of resistance
The sunroof controls are located in the roof (2) to the rear end position (1) or past the
panel. The sunroof can be opened in two posi- point of resistance (3) to the forward end
tions: position (4) and release. The sunroof
G029222
Ventilation position, up at the rear edge opens/closes completely.
Manual operation
Sliding position, backwards/forwards
Opening, automatic Open:
The remote control key must be in position I or Pull the control rearward to the point of
Opening, manual
II. resistance (2). The sunroof moves to maxi-
Closing, manual mum open position as long as the button
is kept depressed.
Closing, automatic
Close:
Opening, ventilation position
Press the control forward to the point of
Closing, ventilation position resistance (3). The sunroof moves to
Power sunroof*
closed position as long as the button is If you need to interrupt closing: Wind deflector
kept depressed.
Press the lock button again. 02
WARNING WARNING
The sunroof's pinch-protection function
Make sure that children or other passengers
only operates during automatic closing, not
are not in danger of becoming trapped in
manual closing.
any way when closing the sunroof with the
remote control. Always operate the sunroof
with caution.
Closing with remote control or lock
button
Sunscreen
The sunroof features a manual, sliding interior
sunscreen. The sunscreen slides back auto-
matically when the sunroof is opened. Grip the
handle and slide the screen forward to close it.
The sunroof has a wind deflector that is folded
up when the sunroof is in the open position.
Pinch protection
The sunroof's pinch protection function is acti-
vated if the hatch is blocked by an object. If
blocked, the sunroof will stop and automati-
cally open to the previous position.
G020157
WARNING
The sunroof's pinch protection function only
One long press on the lock button closes operates during automatic closing, not dur-
the sunroof and all the windows. The doors ing manual closing.
and the tailgate are locked.
Make sure that nobody is in danger of
becoming trapped in any way when closing
the sunroof.
Personal preferences
84
02 Instruments and controls
Personal preferences
Select On/Off depending on whether or not Doors – auto lock central locking button, as well as the outside
you wish the recirculation timer to be When the speed of the car exceeds 7 km/h the door handle button on cars with the keyless
active. doors and tailgate can be locked automatically. system: 02
The On/Off option is available. Pulling the door • Auto. close all windows - all windows
Reset all handle twice unlocks and opens the doors
Resets the climate function options to the fac- and the sunroof are closed simultaneously
from the inside. with one long press on the lock button.
tory settings.
Doors unlock This function can be selected for the unlock
There are two alternatives for unlocking: button on the remote control and the front
Car settings doors' central locking button:
• All doors – one press of the remote control
Retract mirrors when locking* unlocks all doors and the tailgate. • Auto. open all windows – all windows are
When the car is locked/unlocked with the opened simultaneously with one long
remote control the door mirrors can be retrac- • Driver door, then all – one press of the press on the unlock button.
remote control unlocks the driver's door. A
ted/extended automatically. The On/Off option
second press then unlocks all doors and Approach lighting
is available.
the tailgate. Select the time the car's lights should remain
Reduced guard* on when the approach lighting button is
Keyless entry*
The deadlocks function can be temporarily pressed. The following alternatives are availa-
deactivated and the alarm level reduced if
• All doors - all doors are unlocked simul- ble:
taneously.
someone wishes to remain in the car and the
doors have to be locked from the outside. The • Doors on same side – front and rear • 30 seconds
Activate once and Ask on exit options are doors on the same side are unlocked • 60 seconds
simultaneously.
available, see pages 135 and 139. • 90 seconds
• Both front doors – both front doors are
Unlock confirm. light unlocked simultaneously. Home safe lighting
The hazard warning flashers can provide feed- Select the time the car's lights should remain
• Either front door – any door or the tailgate
back when the car is unlocked with the remote can be unlocked separately. on when the left-hand stalk switch is pulled
control. The On/Off option is available. back after the remote control key has been
Simultaneous closing/opening of all removed. The following alternatives are avail-
Lock confirm. light windows able:
The hazard warning flashers can provide feed-
This function can be selected for the lock but-
back when the car is locked with the remote
ton on the remote control and the front doors'
control. The On/Off option is available.
``
Personal preferences
• 30 seconds
02
• 60 seconds
• 90 seconds
Information
• VIN number… - (Vehicle Identification
Number) is the car's unique identity num-
ber.
• Number of keys… - The number of keys
registered for the car is shown.
86
02 Instruments and controls
HomeLink *
``
HomeLink *
The particular distance that is required ess is repeated for approx. 20 seconds Programming individual buttons
between the original remote control and and indicates that the device has a "roll- To reprogram an individual button, proceed in
02 HomeLink depends on the programming ing code". The garage door, gate or sim- accordance with the following:
of the device in question. Perhaps several ilar is not activated when the pro-
grammed HomeLink button is 1. Depress the required button on
attempts will be required at different dis-
depressed. Continue the programming HomeLink and do not release until step 3
tances. Maintain each position for approx.
in accordance with the following. has been completed.
15 seconds before trying a new one.
5. Locate the "programming button1" on the 2. When the indicator lamp on HomeLink
3. Depress the button for the original remote
control and the button to be programmed receiver for the garage door for example, starts to flash, after approx. 20 seconds,
normally located close to the antenna's position the original remote control
on HomeLink simultaneously. Do not
release the buttons until the indicator lamp bracket on the receiver. If you have diffi- 5-30 cm from HomeLink. Monitor the indi-
has changed over from slow to rapid flash- culty in finding the button - consult the cator lamp.
ing. The rapid flashing indicates successful supplier's manual, or contact the supplier The particular distance that is required
programming. via the Internet: www.homelink.com. between the original remote control and
4. Test the programming by depressing the 6. Depress and release the "programming HomeLink depends on the programming of
button". The button flashes for the device in question. Perhaps several
programmed button on HomeLink and
approx. 30 seconds and the next step must attempts will be required at different dis-
watching the indicator lamp:
be carried out within this period. tances. Maintain each position for approx.
• Constant glow: The indicator lamp illu- 15 seconds before trying a new one.
minates with a constant glow when the 7. Depress the programmed button on
button is kept depressed, this indicates HomeLink, while the "programming but- 3. Depress the button on the original remote
that the programming is complete. The ton" is still flashing, keep it depressed for control. The indicator lamp will start to
garage door, gate or similar should now approx. 3 seconds and then release. flash. When the flashing has changed over
be activated when the programmed Repeat the press/hold/release sequence from a slow to a rapid flashing - release
HomeLink button is depressed. up to 3 times to conclude the program- both buttons. The rapid flashing indicates
ming. successful programming.
• Glow not constant: The indicator lamp
flashes quickly for approx. 2 seconds 4. Test the programming by depressing the
and then changes over to a constant programmed button on HomeLink and
glow for approx. 3 seconds. This proc- watching the indicator lamp:
HomeLink *
• Constant glow: The indicator lamp illu- 7. Depress the programmed button on
minates with a constant glow when the HomeLink, while the "programming but-
button is kept depressed, this indicates ton" is still flashing, keep it depressed for 02
that the programming is complete. The approx. 3 seconds and then release.
garage door, gate or similar should now Repeat the press/hold/release sequence
be activated when the programmed up to 3 times to conclude the program-
HomeLink button is depressed. ming.
• Glow not constant: The indicator lamp
flashes quickly for approx. 2 seconds Erasing programming
and then changes over to a constant It is only possible to erase the programming for
glow for approx. 3 seconds. This proc- all the buttons on HomeLink, not for individual
ess is repeated for approx. 20 seconds buttons.
and indicates that the device has a "roll-
Depress the two outer buttons and do not
ing code". The garage door, gate or sim-
release until the indicator lamp starts to
ilar is not activated when the pro-
flash after approx. 20 seconds.
grammed HomeLink button is
depressed. Continue the programming > HomeLink is now set in so-called
in accordance with the following. "learn mode" and is ready to be pro-
grammed once more, see page 87.
5. Locate the "programming button2" on the
receiver for the garage door for example,
normally located close to the antenna's
bracket on the receiver. If you have diffi-
culty in finding the button - consult the
supplier's manual, or contact the supplier
via the Internet: www.homelink.com.
6. Depress and release the "programming
button". The button flashes for approx. 30
seconds and the next step must be carried
out within this period.
92
03 Climate control
both sides.
Sensor location
Open • The sun sensor is on the top side of the
dashboard.
Closed
• The temperature sensor for the passenger
Lateral airflow compartment is behind the climate control
panel.
Vertical airflow
• The outside temperature sensor is located
Aim the outer vents towards the side windows on the door mirror.
to remove misting from the front side windows. • The humidity sensor is located in the inte-
During cold weather - Close the centre vents rior rearview mirror.
for optimum comfort and best demisting.
NOTE
Do not cover or block the sensors with
clothing or other objects.
Control panel
2 8
3 4
1 9
03
G026308
6 7
94
03 Climate control
``
Control panel
03
``
3. Recirculation The air quality system consists of a multi-filter • The defroster functions for the front, side
The function is selected to and a sensor. The filter separates gases and and rear windows can be used to demist
shut out bad air, exhaust particles to reduce the levels of odours and the windows.
gases etc. from the passen- pollution in the passenger compartment. When 4. Defroster
ger compartment. The air in the sensor detects polluted outside air, the air Used to quickly remove mist-
the passenger compartment intakes are closed and the air in the passenger ing and ice from the wind-
03 is recirculated, i.e. no outside compartment is recirculated. A green light (A) screen and side windows. Air
air is taken into the car when illuminates in the button when the air quality flows to the windows at high
this function is activated. If the air in the car sensor is active. fan speed. The light in the
recirculates for too long, there is a risk of mist- Activating the air quality sensor: defroster button illuminates
ing on the insides of the windows. when the function is active.
Press AUTO (1) to activate the air quality
Timer sensor (normal setting). The following also takes place when the
The timer function reduces the risk of icing, defroster function is activated in order to pro-
misting and bad air (if recirculation is selected). Or: vide maximum dehumidification in the passen-
To activate/deactivate the function see Switch between three functions by press- ger compartment:
page 84. ing repeatedly the recirculation button.
• the air conditioning (AC) is automatically
• Air quality sensor engaged – the light (A) switched on (can be switched off with the
NOTE AC button (6)
illuminates.
When Defroster (4) is selected, recirculation • recirculation is automatically disengaged.
is always deactivated.
• No recirculation engaged, provided it is not
required for cooling in hot weather – light When the defroster is switched off the climate
not illuminated. control returns to the previous settings.
3. Air quality system* • Recirculation engaged – the light (M) illu-
Same button as recirculation. 5. Air distribution
minates. The airflow can be distributed
Keep the following in mind: to the windows, dashboard
• As a rule, the air quality sensor should vents or floor by pressing the
always be engaged. air distribution buttons.
• Recirculation is limited in cold weather to
avoid misting.
A symbol on the display above the climate con- 7 and 8. Heated front seats* on the button. Automatic switching off discon-
trol panel and an illuminated light in the relevant To activate front seat heating: nects the rear window and door mirrors after
button indicate which function has been 12 – 20 minutes depending on outside tem-
selected. perature.
Refer to the table on page 100. During cold weather the defrosting* also con-
6. AC – On/Off (ON/OFF) tinues after 20 minutes in order to keep the rear
window and door mirrors free of ice and mist. 03
ON: The air conditioning is on.
It is controlled by the system's Higher heat: The intensity of the defrosting can be adapted
AUTO function. This way, to the outside temperature. This function must
Press the button once – both lights illumi- be switched off manually.
incoming air is cooled and nate.
dehumidified. 10. Temperature selector
Lower heat: The temperatures on the
OFF: Off
Press the button once – one light illumi- driver and passenger sides
When the defroster function is activated the air nates. can be set independently.
conditioning is automatically switched on (can
Heat off: Press the button once to acti-
be switched off with the AC button).
vate one side only. Press
Press the button three times – light not illu- again to activate the other
NOTE minated. side. Press the button a third time to activate
The climate control system's demisting 9. Rear window and door mirror both sides.
function with humidity sensor is significantly defrosters
reduced with the air conditioning in deacti- The active side is indicated by the button's light
Heating is used to quickly and in the display above the climate control
vated mode (OFF), as well as with manually remove misting and ice from
selected air distribution and fan speed. panel.
the rear window and door mir-
rors. Press the button once to When the car is started, the most recent setting
start simultaneous rear win- is resumed.
dow and rearview mirror
defrosting. The function is NOTE
active if one lamp is illuminated in the button. Heating or cooling cannot be hastened by
The function is switched off manually or auto- selecting a higher or lower temperature than
matically. Switch off manually with one press the actual desired temperature.
Air distribution
Air to windscreen and side to prevent misting Air to floor and from dash- in sunny weather with
windows. Some air flows and icing in a cold and board air vents. cool outside tempera-
from the air vents. humid climate. (Not tures.
for low fan speed.)
Airflow to windows and from to ensure good com- Air to floor. Some air flows to to warm the feet.
dashboard air vents. fort in warm, dry the dashboard air vents and
weather. windows.
Airflow to the head and to ensure efficient Airflow to windows, from to provide cooler air for
chest from the dashboard cooling in warm dashboard air vents and to the feet or warmer air
air vents. weather. the floor. to the upper body in
cold weather or hot,
dry weather.
100
03 Climate control
Parking on a hill
If the car is parked on a steep hill, the front of
the car should point downhill to ensure that
there is a supply of fuel to the parking heater.
``
1 No function in cars without trip computer, fuel-driven parking heater as well as stability and traction control system.
Heating of the passenger compartment will After setting TIMER 1 a second start time can NOTE
begin as soon as the engine coolant has be programmed with TIMER 2 by scrolling with
reached the correct temperature. the thumbwheel. All timer programming will be cleared if the
car's clock is reset.
Set the alternative time in the same way as
NOTE TIMER 1.
The car can be started and driven while the
parking heater is running. Deactivating a timer-started heater 03
A timer-started heater can be switched off
manually before the set time has elapsed. Pro-
Setting the timer ceed as follows:
The time when the car shall be used and heated 1. Press the READ button.
is specified with the timer.
2. Use the thumbwheel to scroll to the text
Select between TIMER 1 and TIMER 2. PARK HEAT TIMER 1 or PARK HEAT
1. Scroll with the thumbwheel to PARK TIMER 2.
HEAT TIMER 1. The text ON flashes on the display.
2. Briefly press the RESET button so that the 3. Press RESET.
hours setting starts to flash.
The text OFF is shown with a constant
3. Select the required hour using the thumb- glow and the heater is switched OFF.
wheel.
A timer-started heater can be switched off in
4. Briefly press RESET to move to the flash- accordance with the instructions in the section
ing minutes setting. "Direct start and immediate stop".
5. Select the required minute using the
Clock/timer
thumbwheel.
The heater's time is connected to the car's
6. Briefly press RESET to confirm the setting. clock.
7. Press RESET to activate the timer.
NOTE
The auxiliary heater cannot be switched on
or off manually but is only controlled by the
car's electronics.
When the auxiliary heater is active there may
be smoke from underneath the car, which is
perfectly normal.
03
105
Front seats............................................................................................ 108
Interior lighting...................................................................................... 111
Storage spaces in the passenger compartment .................................. 114
Rear seat............................................................................................... 118
Cargo area............................................................................................ 120
106
INTERIOR
04 Interior
Front seats
Seating position, manual seat Lumbar support1 (driver's and passenger The seats can be adjusted for a certain time
seat*), turn the wheel. after unlocking the door with the remote con-
Backrest rake: turn the wheel. trol key without the key being inserted into the
ignition switch. The seat can always be
Control panel for power seat*. adjusted in ignition position I or II.
Front edge of seat cushion up/down
WARNING
Seat, forwards/backwards
Adjust the position of the driver's seat and
adjust the seatbelt, see page 18, before set- Seat, up/down
ting off, never while driving.
04 Backrest rake
Check that the seat is locked in position.
An overload protection is deployed if one of the
seats is blocked. If this happens, turn off the
Seating position, power seat* ignition and wait a short time before adjusting
the seat again. Only one of the seat's settings
The driver's and passenger seats can be can be adjusted at a time.
adjusted to the optimum sitting and driving
positions.
Forward/backward: lift the handle to adjust
the distance to the steering wheel and ped-
als. Check that the seat is locked after
changing the position setting.
Raise/lower the front of the seat cushion
(driver's and passenger seat*), pump up/
down.
G020199
Raise/lower the seat (driver's and passen-
ger seat*), pump up/down.
Front seats
``
Front seats
Inlaid mats*
Volvo supplies inlay mats which are especially
produced for your car.
WARNING
Before setting off check that the inlaid mat
in the driver area is firmly affixed and
secured in the pins in order to avoid getting
caught adjacent to and under the pedals.
04
Interior lighting
Reading lamps and interior lighting Front roof lighting Vanity mirror*
The front reading lamps are switched on or off
by pressing the relevant button in the roof con-
sole.
04
G020201
G020210
Controls in roof console for front reading lamps
and passenger compartment lighting. The lamp is automatically switched on and off
respectively when the cover is opened or
G030855
Reading lamp left-hand, On/Off
closed.
Interior lighting
Reading lamps, rear. Glovebox lighting
Reading lamp right-hand, On/Off
Reading lamp left-hand rear, On/Off Glovebox lighting is switched on and off
All lighting in the passenger compartment can respectively when the lid is opened or closed.
be switched on in ignition position I and II as Reading lamp right-hand rear, On/Off
well as when the engine is running. The lighting The lamps are switched on or off by pressing
can also be activated within 30 minutes after: the relevant button.
• the engine has been switched off and the
ignition is in position 0 Courtesy lighting
Courtesy lighting (and passenger compart-
• the car has been unlocked but the engine ment lighting) is switched on and off respec-
has not been started.
tively when a side door is opened or closed.
``
Interior lighting
Neutral position
When the switch (2) is in neutral position pas-
senger compartment lighting is switched on
and off automatically in accordance with the
below.
The passenger compartment lighting is
switched on and remains on for 30 seconds if:
• the car is unlocked with the remote control
key or key blade.
• the engine is stopped and the remote con-
trol key is turned to position 0.
112
04 Interior
Interior lighting
04
113
04 Interior
Storage spaces
04
114
04 Interior
G024208
Coat hanger, only for light garments.
Storage compartment and cup holder. The owner's manual and maps can be kept The coat hanger is located on the passenger
Storage pocket* on front edge of centre here for example. There are also holders for seat head restraint. Only hang light garments
rear seat cushion. coins, pens and fuel cards. on the hanger.
The glovebox can be locked with the remote
WARNING control key's detachable key blade. Further
information is available on page 127.
Ensure that no hard, sharp or heavy objects
lie or protrude in such a way that they could
cause injury during heavy braking.
Always secure large and heavy objects with
a seatbelt or cargo retaining straps.
``
04
G026704
G018371
G018372
In the deeper compartment there is space for
There is a storage space under the armrest. 10 normal CD cases. The cases must be stored There is space for a double cup holder under
There is also a smaller storage space in the vertically on the top edge for all 10 to have the roller cover. The space can be used for
detachable armrest. Press the small button space. storage by lifting out the cup holder. Lift at the
and lift the armrest to open the shallow com- rear edge of the cup holder where there is a
partment. Press the large button and lift the recess.
armrest to open the deeper compartment.
If the cup holder is being fitted - first align its
two guide lugs in the two recesses in the front
edge of the space and then press down the
rear edge of the cup holder.
Close the roller cover by gripping its front edge
from below and pulling forward.
116
04 Interior
04
G017441
G019622
A bottle holder for larger bottles is located on An ashtray is located towards the rear of the
When there are no buttons for parking assis- the rear of the tunnel console. tunnel console.
tance and BLIS, see page 169 and page Open the ashtray by pulling the top edge of the
171, the space can be used as a storage com- cover.
partment.
Emptying the ashtray:
WARNING 1. Press in the catch, see preceding illustra-
Objects placed in the storage compart- tion, and tilt the cover up.
ments must not obstruct the parking brake 2. Then lift the ashtray out.
lever when it is applied.
Rear seat
04
G020790
with middle of the back of the head. Raise the
head restraint as necessary.
To lower the head restraint, press the button by The rear seat backrests can be tipped forwards
the right-hand pillar at the same time as push- together, or individually, to make it easier to
ing down the head restraint. To remove the Lowering the backrest. transport long objects. To avoid damaging the
head restraint, the button by the right-hand pil- seatbelts when folding the backrests up or
Rear edge of seat cushion
lar must be pressed while lifting out the head down, these should be hooked onto the grab
restraint. Lock catch handles.
118
04 Interior
Rear seat
NOTE
When the backrest has been raised, the red
indicator should no longer be showing. If it
is still showing then the backrest is not
locked in place.
WARNING
Remember to take down the seatbelts once
you have raised the backrest.
119
04 Interior
Cargo area
Safety net* 2. Do the same on the other side. The attach- Safety grille*
ments on the net spring shut. Pull the net
over towards the left bracket to fit it in
place.
3. Check that the attachments on the safety
net are securely fastened in the keyed
recesses in the roof panel.
G014730
Removing the safety net
1. Pull one of the net's attachments rearward
The retractable safety net storage cassette is to the large notch and pull it out. The safety grille is designed to help prevent
mounted on the rear of the backrest. 2. Detach the other attachment in the same loads or pets from being thrown forward in the
way. passenger compartment in the event of sud-
Using the safety net with raised den braking. For safety reasons, the grille must
backrests. Removing the safety net storage always be correctly fastened and secured.
1. Pull out the safety net horizontally back- cassette.
ward. Extend the right hand attachment 1. Lower the entire backrest. Folding up
and hold it extended. Insert the attachment If the safety grille is in the way it can be folded
into the rear keyed notch in the roof panel. 2. Press the cassette outward to release it up to the roof:
Then press the attachment forward to the from the mounting brackets.
1. Take hold of the bottom of the safety grille.
front notch. The attachment must be
pressed so far that the flange rides over the WARNING 2. Pull straight backward and upward. Then
restriction between the front and rear release. The gas struts prevent the grille
Loads in the cargo area must be firmly
notches. secured even if the safety net is correctly
from dropping down.
fitted. To fold down the grille, do the reverse.
Cargo area
Removing Cargo cover* 4. The button springs back when the cargo
Remove the safety grille as follows: cover is correctly located.
1. Fold the rear seat backrest forward slightly 5. Repeat the procedure on the opposite
(to relieve the load from the gas struts). side.
2. Remove the caps from the nuts on either
side that secure the safety grille.
3. Unscrew the nuts until the threads are flush
with the edge of the nuts.
4. Turn the grille backward in the car slightly
to release it from the trim. Do not angle the 04
grille too much as it can become wedged,
making it difficult to pull out.
G020766
5. Repeat for the other mounting and then
carefully lift the grille out of the car. Cargo cover.
G020767
Attaching Fitting the cargo cover.
To fit the safety grille: Fit the cargo cover as follows:
1. Follow the instructions in the reverse order. 1. Move the front section of the cargo cover 6. Check that the cargo cover is fitted firmly
2. Tighten the two nuts to 24 Nm. backwards/over the cassette. in the cargo area.
In the event of uncertainty about attaching or 2. Following which, fit the cargo cover in its 7. Fit the front section of the cargo cover in
removing the safety grille, consult a workshop tracks along the side panels, furthest into the wedge shaped tracks on the side pan-
- an authorised Volvo workshop is recom- the cargo area. els, against the rear seat.
mended. 3. Push the button forward so that the 8. The cargo cover is now ready for use.
catches are retracted. Following which,
press the cargo cover down in the track. WARNING
Do not place objects on the cargo cover or
on its front section.
``
Cargo area
G020769
1. Tip the backrests slightly forward to
access the safety net cassette. Start with
the 40% section.
G014757
2. Extend the safety net rearward.
3. Fold the backrests back up.
4. Hook the net into the attachment points in The load retaining eyelets are used to fasten
the roof panel as described for raised straps or nets to anchor items in the cargo
backrests. area.
Cargo area
04
G014731
G014756
Fold down the cover to access the electrical The bag holder holds shopping bags in place
socket. This socket works regardless of and prevents them from tipping over and spill-
whether or not the ignition is on. ing their contents in the cargo area.
1. Open the hatch in the cargo area.
NOTE
2. Secure the shopping bags with the strap.
Remember that using the electrical socket
with the engine switched off involves the
risk of discharging the car's battery.
Remote control key Loss of a remote control key Remote control key functions
The car is supplied with two remote control If you lose a remote control key, take the car
keys. and the other remote control keys to a Volvo
workshop - an authorised Volvo workshop is
The remote control keys contain detachable
recommended. The code of the missing
metal key blades for mechanical locking/
remote control key must be erased from the
unlocking of the driver's door and glovebox.
system as a theft prevention measure.
The key blades' unique code is available at
authorised Volvo workshops, which are rec-
ommended for ordering new key blades.
Immobiliser
The remote control keys are fitted with coded
A maximum of six remote control keys/key chips. The code must be accepted by the
blades can be programmed and used for one reader (receiver) in the ignition switch. The car
single car. can only be started if the correct remote control
G019402
key with the correct code is used.
05 Turn signal indication during locking/
unlocking Locking – Locks all doors and the tailgate.
When the car is unlocked using the remote Press and hold (at least 2 seconds) to also
control key or Keyless drive system, two short close the side windows and the sunroof.
flashes of the direction indicators serve to indi- Unlocking – Unlocks the doors and the
cate that unlocking was correctly performed. tailgate. Press and hold (at least 4 seconds)
For locking, the indication takes place with one to also open the side windows.
long flash and only if all locks are locked, after Approach lighting – Switches on the light-
the doors and the tailgate have been closed. ing at a distance – lights up the area around
a car parked in a dark location. Press the
Personal preferences in the menu system can
button once to switch on the interior light-
be used to the deactivate indication via the
ing, position/parking lamps, number plate
direction indicators. There will then be no visual
lighting and door mirror lamps (option). The
indication as to whether the lock status is cor-
lighting is switched off automatically after
rect, see page 85.
126
05 Locks and alarm
30, 60 or 90 seconds. For information on Detachable key blade Removing the key blade
setting the delay time, see page 85. To remove the key blade from the remote con-
Tailgate – Press the button once to unlock trol key:
the tailgate only.1 Slide the spring-loaded catch to the side.
Panic function – Used to attract attention
in an emergency. Press and hold the red Pull out the key blade at the same time.
button for at least three seconds or press
it twice within three seconds to activate the Attaching the key blade
direction indicators and the horn. The func- Be careful when inserting the key blade into the
tion can be turned off with the same button remote control key.
once it has been active for at least 5 sec- 1. Hold the remote control key with the nar-
onds. Otherwise the function switches off row end pointing down and lower the key
automatically after 30 seconds. blade into its slot.
G019403
2. Lightly press the key blade to lock it in
WARNING position. You should hear a "click". 05
If the sunroof and windows are closed using Using the remote control key's detachable key
the remote control key, check that no one is blade: Unlocking doors with the key blade
in danger of getting hands caught. If central locking cannot be activated with the
• the driver's door can be opened manually remote control key, e.g. if the batteries are dis-
if central locking cannot be activated with charged, then the driver's door can be
IMPORTANT the remote control key, see page 131.
unlocked and opened as follows:
The narrow section of the remote control • access to the glovebox can be blocked,
see page 128. 1. Insert the key blade in the driver's door
key is particularly sensitive - this contains
the chip. The car cannot be started if the keyhole.
• the rear doors' mechanical child safety
chip is damaged. locks can be activated/deactivated, see 2. Turn the blade 45 degrees clockwise and
page 137. open the door.
• PACOS* activated/deactivated, see
page 24.
05
G020034
128
05 Locks and alarm
Active locks
G019450
Active locks for remote control key with 05
key blade.
Active locks for remote control key with-
out key blade.
129
05 Locks and alarm
Keyless drive*
Keyless lock and ignition system Remote control key max. 1.5 m from the • the READ button has been pressed.
car
Never leave any remote control key in the
In order to open a door or the tailgate, a remote
control key must be no more than approx. car
1.5 m from the car door handle or tailgate. If a remote control key with keyless drive func-
tion is left in the car, it is made passive when
This means that the person who wishes to the car is locked. This prevents unauthorised
open a door must have the remote control key entry.
with him or her. It is not possible to open a door
if the remote control key is on the other side of If someone breaks into the car and finds the
the car. remote control key, it can be activated and
used again. It is therefore important to handle
The grey area in the illustration indicates the all remote control keys with equal care.
G019451
range covered by the system's antennas.
Interference to remote control key
If someone leaves the car and takes a keyless
drive remote control key with them, a warning function
05 Electromagnetic screening and fields can inter-
Keyless function range message appears on the information display
and a reminder signal sounds. The warning fere with the keyless drive system. To avoid
The keyless drive system allows the car to be this: do not place the remote control key near
message disappears when the remote control
unlocked, driven and locked without the need mobile phones, metallic objects or, for exam-
key is brought back to the car or when the igni-
for a key. You simply need to have the remote ple, in a metal briefcase.
tion dial is turned to position 0. The warning is
control key with you in a pocket or a bag.
only issued if the ignition dial is in position I or If interference is experienced nonetheless, use
The system makes it easier and more conven- II after someone has opened and closed a the remote control key and key blade in the
ient to open the car, for example with shopping door. normal way, see page 126.
bags in one hand and a child in the other. It
The warning message and reminder signal dis-
saves you having to take out or look for the
appear when the remote control key is brought
remote control key.
back to the car after one of the following
The two remote control keys incorporate the actions:
keyless drive function. You can order addi-
tional remote controls. The keyless drive sys-
• a door has been opened and closed
tem can handle up to six remote controls. • the ignition dial has been turned to position
0
Keyless drive*
Unlocking
When the remote control key is within the range
covered by the system's antennas:
1. Open the doors by pulling the relevant han-
dle.
G020033
G020225
2. Open the tailgate by pressing under the
tailgate opening button and lift the tailgate. 05
Cars with the keyless system have a button on the
outside door handles. If for some reason the keyless drive function in If central locking cannot be activated with the
the remote control key is not operating, the car remote control key, e.g. if the batteries are dis-
When the remote control key is within the range charged, then the driver's door can be opened
covered by the system's antennas, the doors can be unlocked using the remote control key
functions, see page 126. as follows:
and the tailgate are locked as follows:
1. To access the keyhole: Carefully prize out
Push in the lock button on one of the door Power seat – remote control key with the plastic cover in the handle by inserting
handles. memory function the key blade in the hole on the bottom of
All doors must be closed before the lock button If several people with keyless drive remote the cover.
is pushed in. Otherwise they will not lock. control keys get into the car, then the driver's
seat will be adjusted for the person who opens 2. Unlock the door using the key blade.
When the car is locked, the lock buttons on the the door first.
inside of the doors retract.
``
Keyless drive*
When the driver's door is unlocked using the Centre console, under the rear section
key blade and is opened, the alarm is trig-
gered. It is switched off by inserting the Centre console, under the front section
remote control key in the ignition switch, see
page 139.
WARNING
People with pacemaker operations should
Antenna location not come closer than 22 cm to the keyless
system's antennae with their pacemaker.
This is to prevent interference between the
pacemaker and the keyless system.
Personal preferences
05 The Keyless Drive system can have personal
preferences applied, see page 85.
G020074
Low battery in remote control key 1. Place the remote control key with the key-
When the battery runs down and full function- pad downward and prize up the cover
ality cannot be guaranteed, the information using a small screwdriver.
symbol and display show KEY BATTERY 2. Remove the cover.
LOW VOLTAGE or CAR KEY - CHANGE 3. Carefully examine how the battery's (+) and
BATTERY. (–) sides are fitted (there is a diagram under
the cover).
Changing the remote control key 4. Prize out and change the battery. Avoid
battery touching the battery and its terminals with
your fingers.
5. Refit the cover and press it in.
Dispose of the old battery in an environmen-
tally-responsible manner.
05
G019406
133
05 Locks and alarm
Locking/unlocking the car from Rapid closing Locking/unlocking the car from inside
outside Press and hold (at least 2 seconds) on the
For cars with the Keyless system, see remote control key's lock button to close all
page 130. windows and sunroof* at the same time.
Unlocking
Tailgate
Using the remote control key's unlock button
the car can be unlocked in two different ways Unlocking
(select in personal settings, see page 85): Unlocking tailgate only:
• One press unlocks the doors and the tail- Press the remote control key's button to
gate unlock the tailgate.
• One press unlocks the driver's door and a
second press unlocks the other doors and Locking
the tailgate. If the doors are locked when the tailgate is
G007451
closed then it remains unlocked. Lock with the
05 Locking remote control key's lock button or from inside
The remote control key's lock button locks the to lock both doors and the tailgate.
doors and tailgate simultaneously. With the central locking button on the driver's
door, the doors and tailgate can be locked or
Automatic relocking unlocked simultaneously.
NOTE
If none of the doors or the tailgate is opened
The car can be locked even if the tailgate is within 2 minutes of unlocking, all are locked Unlocking
open - when the tailgate is then closed there again automatically (does not apply to locking A door cannot be unlocked by pulling up its
is a risk that the keys will be locked in*. from inside). This function reduces the risk that lock button.
the car is left unlocked unintentionally. (For Press the upper section of the central lock-
WARNING cars with alarm, see page 139.)
ing button .
Be aware that you can be locked in the car
Global opening
if it is locked from the outside with the
remote control key. You cannot then leave Press the upper section of the central lock-
the car using any of the controls inside the ing button .
car.
A long press (at least 4 seconds) also • Pull one of the door handles twice Temporary deactivation
opens all the side windows simultaneously • Press the upper section of the central lock-
- for example, to quickly ventilate the pas- ing button and pull the door handle.
senger compartment during hot weather.
The function can be activated/deactivated by
Locking means of personal preferences, see page 85.
Press the lower section of the central lock- A
ing button . Deadlocks *1
Press and hold (at least 2 seconds) to also When deadlocked, the doors cannot be
close all windows and the sunroof* at the opened from the inside if they are locked with
same time. the remote control key.
All doors can be locked with each respective The deadlocks are activated with the remote
door's lock button. control key and are set after a 10-25 second E B
delay after the doors have been locked. D C
Opening the doors 05
When the doors are locked from the inside: The car can only be unlocked from a deadlock
state with the remote control key. The driver's
Pull the handle twice to unlock and open door can also be unlocked with the detachable
the door. key blade.
G026307
Automatic locking
When the speed of the car exceeds 7 km/h the Active menu options are indicated with a cross.
doors and tailgate are locked automatically.
Display
When the function is activated and the doors
have been locked they can be opened in two MENU
ways: EXIT
Manual select, child lock, rear doors Electrical locking of the rear doors and The lamp in the button illuminates when the
power windows* lock is active.
NOTE
Cars with electric child safety locks do not
also have manual child locks.
G014697
05
Manual child lock in left-hand rear door.
The door cannot be opened from inside. Driver's door control panel.
When the electric child safety lock is active
The door can be opened from inside.
then the rear:
The child safety lock controls are found on the
trailing edge of the rear doors and are only
• windows can only be opened with the driv-
er's door control panel
accessible when the doors are open.
• doors cannot be opened from inside.
To activate or deactivate the child safety locks:
1. Child safety locks are activated in key posi-
1. Remove the remote control key's key tion I or II.
blade.
2. Press the switch on the driver's door.
2. Turn the control using the key blade.
A message appears on the information dis-
play.
Alarm*
G020227
• the battery's cable is disconnected The alarm is fully armed when the car's
05 • anyone tries to disconnect the siren. direction indicators have made one long
A red LED on the instrument panel indicates flash and the LED on the instrument panel
flashes once every other second.
the alarm system's status:
• LED not lit – the alarm is not armed.
• The LED flashes once every other second Disarming the alarm
– Alarm is armed. Press the remote control key unlock but-
• The LED flashes rapidly after disarming the ton. Two short flashes from the car's direc-
alarm and until key position II is activated tion indicators confirm that the alarm is
– the alarm has been triggered. disarmed and that the doors are unlocked.
If there is a fault in the alarm system, a message
appears on the display. At which point you
should contact a workshop - an authorised
Volvo workshop is recommended.
Alarm*
Automatic re-arming of the alarm Remote control key not working Reduced alarm level
This function prevents the car being left with To avoid inadvertently triggering of the alarm -
alarm disarmed unintentionally. for example when leaving a dog in the car or
during a ferry crossing - the movement and tilt
If the car is unlocked with the remote control
detectors can be temporarily switched off.
key (and the alarm is disarmed) but none of the
doors or the tailgate is opened within The procedure is the same as with the tempo-
2 minutes, then the alarm is automatically re- rary disengaging of deadlocks, see page 135
armed. The car is relocked at the same time.
Testing the alarm system
Deactivating a triggered alarm
Testing the movement detector in the
Press the unlock button on the remote
control key or insert the key in the ignition passenger compartment
G019420
switch. 1. Open all the windows.
Confirmation is given by two short flashes from 2. Arm the alarm. Activation of the alarm is
confirmed by the lamp flashing slowly. 05
the direction indicators.
If for some reason the remote control key is not
working, the alarm can still be switched off and 3. Please wait 30 seconds.
Alarm signals the car started as follows: 4. Test the movement detector in the pas-
When the alarm is triggered, the following hap- 1. Open the driver's door with the key blade. senger compartment, such as by lifting out
pens: The alarm is triggered and the siren a bag from a seat. A siren should sound
sounds. and all direction indicators should flash.
• A siren sounds for less than 25 seconds.
The siren has its own battery which is used 2. On cars with the keyless drive system: First 5. Deactivate the alarm by unlocking the car
if the car battery has insufficient charge or with the remote control key.
remove the knob by pressing in the
is disconnected.
catch (1) and pulling out (2). Test of alarm for doors
• The direction indicators flash for 1. Arm the alarm.
5 minutes or until the alarm is deactivated. 3. Insert the remote control key in the ignition
switch (3). The alarm is deactivated. The 2. Please wait 30 seconds.
alarm light flashes rapidly until the remote
control key is turned to key position II. 3. Unlock the driver's door with the key blade.
``
Alarm*
05
141
General.................................................................................................. 144
Refuelling.............................................................................................. 146
Alcoguard*............................................................................................ 150
Starting the engine ............................................................................... 154
Starting the engine – Flexifuel............................................................... 156
Keyless drive*........................................................................................ 158
Manual gearbox.................................................................................... 159
Automatic gearbox................................................................................ 160
Brake system........................................................................................ 165
DSTC – Stability and traction control system* ..................................... 167
Park Assist*........................................................................................... 169
BLIS* – Blind Spot Information System ............................................... 171
Towing and recovery............................................................................. 174
Start assistance.................................................................................... 176
Driving with a trailer.............................................................................. 177
Towing equipment*............................................................................... 179
Detachable towbar* ............................................................................. 181
Loading................................................................................................. 185
Adjusting headlamp pattern ................................................................. 186
General
144
06 Starting and driving
General
• If the temperature gauge for the engine's Do not overload the battery Slippery driving conditions
cooling system goes into the red zone - The electrical functions in the car load the bat- Practise driving on slippery surfaces under
stop and let the engine idle for a few tery to varying degrees. Avoid having the controlled conditions to learn how the car
minutes. remote control key in key position II when the reacts.
• If the car overheats, the air conditioning engine is switched off. Instead use the I mode
may be switched off temporarily. - which uses less power.
• Do not turn the engine off immediately you Note that the 12 volt outlet in the cargo area
stop after a hard drive. supplies power even when the remote control
key has been removed from the ignition switch.
NOTE
Also, be aware of different accessories that
It is normal for the engine's cooling fan to load the electrical system. Do not use functions
operate for a while after the engine has been which use a lot of power when the engine is
switched off.
switched off. Examples of such functions are:
145
06 Starting and driving
Refuelling
Opening the fuel filler flap 3. Take out the cap. General information on fuel
4. Hang up the cap on the inside of the fuel
filler flap. WARNING
Always avoid inhaling fuel vapour and get-
NOTE ting fuel splashes in the eyes.
Put the petrol cap back on after refuelling. In the event of fuel in the eyes, remove any
Turn until one or more clear clicks are heard. contact lenses and rinse the eyes in plenty
of water for at least 15 minutes and seek
medical attention.
Filling up with fuel Never swallow fuel. Fuels such as petrol,
Do not overfill the tank but fill until the pump bioethanol and mixtures of them and diesel
nozzle cuts out. are highly toxic and could cause permanent
injury or be fatal if swallowed. Seek medical
attention immediately if fuel has been swal-
NOTE lowed.
Don not forget to switch off the fuel-driven heater Excess fuel in the tank can overflow in hot
before refuelling! weather.
WARNING
Open the fuel filler flap with the button on the Fuel which spills on to the ground can be
lighting panel, see page 63. The engine must Fuel of a lower quality than that specified ignited by the exhaust fumes.
06 should not be used as engine power and fuel
be switched off before the flap can be opened.
The fuel flap is located on the rear right wing. consumption could be negatively affected, for Switch off the fuel-driven heater before star-
more information see the following section ting to refuel.
Closing Fuel. Never carry an activated mobile phone
Push in the flap until you hear a click. when refuelling. The ring signal could cause
spark build-up and ignite petrol fumes,
Fuel cap leading to fire and injury.
1. Turn the fuel cap until an obvious resis-
tance is felt.
2. Turn past the resistance until it comes to a
stop.
146
06 Starting and driving
Refuelling
IMPORTANT tinuously controls the injectors. The ratio of fuel Bioethanol E85
to air directed to the engine is continuously Do not modify the fuel system or its compo-
Mixing different types of fuel or the use of adjusted. These adjustments create optimal
fuel not recommended invalidates Volvo's nents, and do not replace components with
conditions for efficient combustion of harmful parts that are not specifically designed for use
guarantees, and any associated service
agreement. This applies to all engines. emissions (hydrocarbons, carbon monoxide with bioethanol.
NOTE: It does not apply to cars with engines and nitrous oxides) using the three-way cata-
that are adapted to run on ethanol fuel (E85). lytic converter.
WARNING
Methanol must not be used. A decal on the
CO2 emissions, fuel consumption and tank vol- Petrol inside of the fuel filler flap shows the correct
ume, see page 289 Petrol must meet the EN 228 standard. Most alternative fuel.
engines can be run with octane ratings of 91, The use of components not designed for
Catalytic converter 95 and 98 RON. bioethanol engines could cause fire, injury
The purpose of the catalytic converter is to or engine damage.
purify exhaust gases. It is located in the flow of • 91 RON must not be used for 4-cylinder
exhaust gases close to the engine so that it engines and should only be used in excep-
tional cases with other engines. Reserve fuel can
quickly reaches operating temperature. The
catalytic converter consists of a monolith • 95 RON can be used for normal driving. The reserve fuel can should be filled with petrol,
(ceramic or metal) with channels. The channel see the NOTE box, page 156.
• 98 RON is recommended for optimum per-
walls are lined with a thin layer of platinum/rho- formance and minimum fuel consumption.
dium/palladium. These metals act as catalysts, When driving in temperatures above +38 °C,
IMPORTANT 06
i.e. they participate in and accelerate a chem- fuel with the highest possible octane rating is Make sure the reserve fuel can is securely
ical reaction without being used up them- recommended for optimum performance and fastened and that its cap is sealed.
selves. fuel economy.
Lambda-sondTM oxygen sensor WARNING
The Lambda-sond is part of a control system IMPORTANT
Ethanol is sensitive to sparks, and explosive
intended to reduce emissions and improve fuel • Always refuel with unleaded petrol so as gases could form in the reserve fuel can if it
economy. not to damage the catalytic converter. is refuelled with ethanol.
An oxygen sensor monitors the oxygen content • Do not use additives not recommended
of the exhaust gases leaving the engine. This by Volvo.
value is fed into an electronic system that con-
``
147
06 Starting and driving
Refuelling
Diesel companies. This fuel is less viscous at low tem- engine, once the fuel tank has been filled with
Diesel must meet the EN 590 or JIS K2204 peratures and reduces the risk of paraffin pre- diesel:
standards. cipitate.
1. Insert the remote control key in the ignition
switch and turn to key position II (see
IMPORTANT IMPORTANT page 154).
Only ever use fuel that fulfils the European Use special winter grade fuel during cold 2. Wait approx. 1 minute.
diesel standard. months. 3. To start the engine: Depress the brake and/
or clutch pedal, and turn the remote control
The risk of condensation in the fuel tank is key to start position III.
IMPORTANT reduced if the tank is kept well filled. When
Diesel type fuels which must not be used: refuelling, check that the area around the fuel Draining condensation from the fuel filter
special additives, Marine Diesel Fuel, fuel filler pipe is clean. Avoid spilling fuel onto the The fuel filter separates condensation from the
oil, RME1 (Rape Methyl Ester) and vegetable paintwork. Wash off any spillage with deter- fuel. Condensation can disrupt engine opera-
oil. These fuels do not fulfil the requirements gent and water. tion.
in accordance with Volvo recommendations
and generate increased wear and engine The fuel filter must be drained at the intervals
damage that is not covered by the Volvo IMPORTANT specified in the Service and Warranty Booklet
warranty. The sulphur content must be a maximum of or if you suspect that the car has been filled
50 ppm. with contaminated fuel.
06 Diesel engines are sensitive to contaminants,
such as excessively high volumes of sulphur IMPORTANT
Empty tank
particles for example. Only use diesel fuel from The design of the fuel system in a diesel engine Certain special additives remove the water
well-known producers. Never use diesel of means that if the vehicle runs out of fuel, the separation in the fuel filter.
dubious quality. tank may need to be vented in the workshop in
At low temperatures (-40 °C to -6 °C), a paraffin order to restart the engine after fuelling. Diesel particle filter (DPF)
precipitate may form in the diesel fuel, which Once the engine has stopped due to fuel star- Diesel cars may be equipped with a particle fil-
may lead to ignition problems. Special diesel vation, the fuel system needs a few moments ter, which results in more efficient emission
fuel designed for low temperatures around to carry out a check. Do this before starting the control. The particles in the exhaust gases are
freezing point is available from the major oil collected in the filter during normal driving. So-
1 Diesel fuel may contain a certain amount of RME, but further amounts must not be added.
148
06 Starting and driving
Refuelling
called "regeneration" is started in order to burn way. The car should then be driven for approx-
away the particles and empty the filter. This imately 20 minutes more.
requires the engine to have reached normal
operating temperature. NOTE
Regeneration of the filter takes place automat- A smaller reduction of engine power may be
ically at an interval of approximately noticed temporarily during regeneration.
300 – 900 km depending on driving conditions.
Regeneration normally takes 10 - 20 minutes. When regeneration is complete the message is
It may take a little longer at a low average cleared automatically.
speed. Fuel consumption may increase slightly
during regeneration. IMPORTANT
The rear window heating may be activated If the filter fills up it may be incapable of
automatically to increase the load on the functioning. Then it can be difficult to start
engine during regeneration without warning. the engine and there is a risk that the filter
will have to be replaced.
Regeneration in cold weather
If the car is frequently driven short distances in
Use the parking heater* in cold weather so that
cold weather then the engine does not reach
the engine reaches normal operating tempera-
normal operating temperature. This means that
ture more quickly.
regeneration of the diesel particle filter does 06
not take place and the filter is not emptied.
When the filter has become
approximately 80% full of particles, the yellow
information symbol on the instrument panel
illuminates, and the message SOOT FILTER
FULL SEE OWNER MANUAL is shown on the
instrument panel display.
Start regeneration of the filter by driving the car
until the engine reaches normal operating tem-
perature, preferably on a main road or motor-
Alcoguard*
Alcoguard*
1. When indicator lamp (6) is green the Alco- Result after breath test To bear in mind
lock is ready for use.
Lamp (5) + Dis- Specification Before the breath test
2. Withdraw the Alcolock from its holder. If play text
the Alcolock is outside the car when it is In order to obtain correct function and as accu-
unlocked then it must first be activated Green lamp + Start the engine - no rate a measurement result as possible:
with the switch (2). ALCOGUARD alcohol content • Avoid eating or drinking approx.
3. Fold up the nozzle (1), take a deep breath APPROVED TEST measured. 5 minutes before the breath test.
and blow with an even pressure until a • Avoid excess windscreen washing - the
"click" is heard after approx. 5 seconds. Yellow lamp + Engine starting pos-
alcohol in the washer fluid may result in an
The result will be one of the alternatives in ALCOGUARD sible - measured incorrect measurement result.
the following table Result after breath APPROVED TEST alcohol content is
test. above 0.1 promille Change of driver
but below the limit In order to ensure that a new breath test is car-
4. If no message is shown then the transmis-
sion to the car may have failed - in which value in forceA. ried out in the event of a change of driver -
case, press button (3) to transmit the result depress the switch (2) and the send button (3)
Red lamp + DISAP- Engine starting not simultaneously for approx. 3 seconds. At
to the car manually.
PROVED TEST possible - measured which point the car returns to start inhibition
5. Fold down the nozzle and refit the Alcolock WAIT 1 MINUTE alcohol content is
in its holder. mode and a new approved breath test is
above the limit value required before starting the engine.
6. Start the engine following an approved in forceA.
breath test within 5 minutes - otherwise it 06
A Limits vary between countries, so find out what limits apply.
Calibration and service
must be repeated. See also the section entitled General information on the The Alcolock must be checked and calibrated
Alcolock on page 150
at a workshop1 every 12 months.
NOTE 30 days before recalibration is necessary the
display shows ALCOGUARD CALIBR.
After a completed period of driving, the
REQUIRED. If calibration is not carried out
engine can be restarted within 30 minutes
without a new breath test. within these 30 days then normal engine star-
ting will be blocked - only starting with the
Alcoguard*
Bypass function will then be possible, see In extremely cold weather the heating time can Activating the Bypass function
page 152 section Emergency situation. be reduced by taking the Alcolock indoors. • Depress and hold the left-hand stalk
The message can be cleared by pressing the switch READ button and the button for
Emergency situation hazard warning flashers simultaneously for
send button (3) once. Otherwise it goes out on In the event of an emergency situation, or if the approx. 5 seconds - the display first shows
its own after approx. 2 minutes but then reap- Alcolock is out of order or has been removed, BYPASS ACTIVATED WAIT 1 MINUTE
pears each time the engine is started - only it is possible to bypass the Alcolock in order to and then ALCOGUARD BYPASS
recalibration at a workshop1 can clear the mes- drive the car. ENABLED - after which the engine can be
sage permanently. started.
NOTE
Cold or hot weather This function can be activated several times.
The colder the weather the longer it takes All Bypass activation is logged and saved in The error message shown during driving can
memory, see page 12 in the section, only be cleared at a workshop1.
before the Alcolock is ready for use:
Recording data.
Activating the Emergency function
Temperature (ºC) Maximum heat- After the Bypass function has been activated • Depress and hold the left-hand stalk
ing time (sec- the display shows ALCOGUARD BYPASS
switch READ button and the button for
onds) hazard warning flashers simultaneously for
ENABLED the whole time while driving and approx. 5 seconds - the display shows
+10 — +85 10 can only be reset by a workshop1. ALCOGUARD BYPASS ENABLED and
The Bypass function can be tested without the the engine can be started.
–5 — +10 60
06 error message being logged - in which case, This function can be used once, after which a
–40 — –5 180 carry out all the steps without starting the car. reset must be made at a workshop1.
The error message is cleared when the car is
At temperatures below -20 ºC or above locked.
+60 ºC the Alcolock requires additional power When the Alcolock is installed, either the
supply. The display shows ALCOGUARD Bypass or Emergency function is selected as
INSERT POWER CABLE. In which case, con- the bypassing option. This setting can be
nect the power supply cable from the glovebox changed afterwards at a workshop1.
and wait until indicator lamp (6) is green.
Alcoguard*
Before starting the engine NOTE Turn the ignition key to the start position
Apply the parking brake. III and just release it - the starter motor
The idling speed can be noticeably higher then works automatically until the engine
Note that if the car is equipped with an alcolock than normal for certain engine types during
has started.
then a breath test must first be approved cold starting. This is in order that the emis-
before the engine can be started, see sions system can reach normal operating
temperature as quickly as possible, which NOTE
page 150.
minimises exhaust emissions and protects
If the diesel engine is started in extreme cold
the environment.
Automatic gearbox without waiting for engine preheating, then
Move the gear selector in position P or N. the automatic start sequence can be
delayed for a couple of seconds.
Manual gearbox Starting the engine
Put the gear lever in neutral and hold the clutch Petrol
pedal fully depressed. This is particularly Key positions
Turn the remote control key to key position
important in very cold conditions. III. If the engine does not start within 0 – Locked position
5–10 seconds, release the key and try The steering lock is activated
WARNING again. when the remote control key
Never remove the remote control key from is removed from the ignition
the ignition switch while driving or when the Diesel
switch.
car is being towed. The steering lock could 1. Turn the remote control key to key position
06 otherwise be activated, making it impossi- II.
ble to steer the car. > An indicator symbol in the combined
The remote control key must be in key posi- instrument panel shows that engine pre- I – Radio position
tion II when the car is being towed. heating is underway, see page 55. Steering lock deactivated.
2. Turn the ignition key to position III when Certain functions can be
the indicator symbol goes out. used. The engine's electrical
system is not activated.
Autostart *
With the autostart function, there is no need to
hold the remote control key (or ignition dial on
cars with Keyless Drive, see page 130) in key
position III until the engine has started.
155
06 Starting and driving
General information about starting If the engine still does not start bioethanol E85, an engine block heater should
with Flexifuel Please wait for one minute, fully depress be used for about 2 hours to facilitate the quick
The engine is started in the same way as in a the accelerator pedal and repeat the pre- starting of the engine.
petrol-engined car, see page 154. vious procedure. The lower the temperature, the longer the time
required with the engine block heater. At
NOTE IMPORTANT -20 °C the heater should be used for approx. 3
If the engine does not start despite repeated hours.
The immobiliser is activated in the event of
repeated start attempts. Before a new start start attempts, contact a workshop - an Cars intended for E85 have an electric engine
attempt is made the key/dial must first be authorised Volvo workshop is recom-
block heater*. Starting and driving with a pre-
turned back to position I or 0. mended.
heated engine involves significantly lower
emissions and reduced fuel consumption. For
Engine block heater* this reason you should aim to use the engine
In the event of starting difficulties block heater throughout the winter months.
If the engine does not start at the first start
attempt, proceed as follows:
WARNING
1. Depress the accelerator pedal 1/3 to 1/2.
The engine block heater is powered by high
2. Turn the remote control key/ignition dial to voltage. Fault tracing and repair of an elec-
key position III. tric engine block heater and its electrical
06 connections must only be carried out by a
3. When the engine has started, ease the workshop - an authorised Volvo workshop
accelerator pedal gradually as the engine is recommended.
speed increases.
NOTE IMPORTANT
Points to remember for carrying reserve After the fuel mixture in the tank has been
fuel: changed an adaptation should be made by
driving at an even speed for about 15
• In the event of stalling due to an empty minutes.
fuel tank, bioethanol E85 from a reserve
fuel can may make the engine difficult
to start in extreme cold. This is avoided If the battery has been discharged or discon-
by filling the reserve fuel can with 95 nected then a slightly longer period of driving
octane petrol. is required for the adaptation as the memory
for the electronics has been cleared.
For more information on Flexifuel's bioethanol
E85 fuel, see page 147.
Fuel adaptation
If the fuel tank is filled with petrol after the car
has been driven on bioethanol E85 (or vice
versa) then the engine may run slightly
unevenly for a time. For this reason it is impor-
tant to allow the engine to accustom itself 06
(adapt) to the new fuel mixture.
Adaptation takes place automatically when the
car is driven for a short period at an even
speed.
157
06 Starting and driving
Keyless drive*
General Starting the car Starting with the remote control key
Depress the clutch pedal (cars with manual
gearbox) or brake pedal (cars with auto-
matic gearbox).
Petrol engine
Press in and turn the ignition dial to key
position III.
Diesel engine
1. First turn the ignition dial to key position II
and wait until the diesel indicator symbol in
the combined instrument panel goes out,
see page 55.
G019410
G019420
2. Following which, turn the ignition dial to
position III.
The keyless drive system allows the car to be If the remote control key's battery is dis-
unlocked, driven and locked without the need charged then the Keyless Drive function does
for a key, see page 130. not work. In which case, start the car by using
06 the remote control key as ignition dial.
The ignition switch ignition dial is used in the
same way as the remote control key. One pre- 1. Press in the catch in the ignition dial.
condition for starting the car is that the car's
2. Pull the ignition dial out from the ignition
remote control key is located inside the pas-
switch.
senger compartment or the cargo area.
3. Insert the remote control key into the igni-
tion switch and start in the same way as
with the ignition dial.
Manual gearbox
Automatic gearbox
Geartronic automatic gear positions NOTE Geartronic manual gear positions (+/-)
The driver can also change gear manually
The brake pedal must be depressed in order
to be able to disengage the gear lever from using the Geartronic automatic gearbox. The
the P position. car engine-brakes when the accelerator pedal
is released.
The gearbox is mechanically blocked when Manual gearshift mode is obtained by moving
the P position is engaged. Always apply the the lever to the side from position D to the end
parking brake when parking the car. position at +/–. The information display shifts
the indication from D to one of the figures 1 –
R – Reverse 6, which is equivalent to the gear that is
The car must be stationary when position R is engaged just then, see page 53.
selected.
• Move the lever forwards towards + (plus)
G018264
160
06 Starting and driving
Automatic gearbox
G020237
tion.
To prevent overrevving the engine, the gearbox
control program has a protective downshift Electric gear inhibitor – Shiftlock Parking
inhibitor which prevents the kick-down func- position (P position)
The gear selector can be moved forward and
tion. To be able to move the gear selector from the
back freely between N and D. Other positions
Geartronic does not permit downshifting/kick- are locked with a latch that is released with the P position to other gear positions, the remote
down which would result in an engine speed inhibitor button on the gear selector. control key must be in position II and the brake 06
high enough to damage the engine. Nothing pedal must be depressed.
With the inhibitor button depressed the lever
happens if the driver still tries to shift down in
can be moved forwards or backwards between Shiftlock – Neutral (N position)
this way at high engine speed – the original
P, R, N and D. If the gear selector is in the N position and the
gear remains engaged.
car has been stationary for at least three sec-
When kick-down is activated the car can onds (irrespective of whether the engine is run-
change one or more gears at a time depending ning) then the gear selector is locked in the N
on engine speed. The car changes up when the position.
engine reaches its maximum speed in order to
prevent damage to the engine. To be able to move the gear selector from the
N position to another gear position, the brake
pedal must be depressed and the remote con-
trol key must be in position II.
``
161
06 Starting and driving
Automatic gearbox
Disengaging the gear selector inhibitor Cold start Automatic gearbox, Powershift * 1
When starting in low temperatures, the gear
changes can sometimes feel hard. This is due
to the gearbox oil's viscosity at low tempera-
tures. To reduce engine emissions, the gear-
box shifts up later than normal when the engine
is started at low temperatures.
NOTE
Depending on the engine temperature when
the engine is started, the idle speed after a
cold start may be higher than normal for
certain engine types.
G018263
G018264
D: Automatic gear positions. M (+/–): Manual gear
In certain cases, it may be necessary to move positions.
the car when it is not driveable, for example if
the battery is flat. Proceed as follows to move Powershift is a six-stage automatic gearbox
the car: that has double mechanical clutch discs in
06
contrast to a conventional automatic gearbox.
1. There is a small cover behind P-R-N-D on A conventional automatic gearbox has a
the gear selector panel. Open it at the rear hydraulic torque converter that transfers power
edge. from the engine to the gearbox.
2. Fully insert the key blade from the remote Powershift transmission operates in the same
control key. way and has similar controls and functions as
3. Hold the key blade down and at the same the Geartronic automatic transmission, descri-
time move the gear lever out of the P posi- bed in the previous section.
tion.
Automatic gearbox
To bear in mind Overheating during slow driving in queues can Text message and action
The transmission's double clutch has overload be avoided by driving in stages: Stop the car In some situations the display can show a mes-
protection that is activated if it becomes too and wait with your foot on the brake pedal until sage at the same time as a symbol is illumi-
hot, e.g. if the car is held stationary with the there is a moderate distance to the traffic nated.
accelerator pedal on an uphill gradient for a ahead, drive forward a short distance, and then
The table shows three steps with an increased
long time. wait another moment with your foot on the
degree of seriousness should the gearbox
brake pedal.
Overheated transmission causes the car to become too hot. In parallel with the display text
shake and vibrate, and the warning symbol illu- the driver is also advised that the car's elec-
minates and the information display shows a IMPORTANT tronics are temporarily changing the driving
message. The transmission can also overheat Use the foot brake to hold the car stationary characteristics. Follow the instructions on the
during slow driving in queues (10 km/h or on an uphill gradient - do not hold the car information display where appropriate.
slower) on an uphill gradient, or with a trailer with the accelerator pedal. The gearbox
hitched. The transmission cools down when could then overheat.
the car is stationary, with foot brake depressed
and the engine running at idling speed.
06
``
163
06 Starting and driving
Automatic gearbox
TRANSM. OVERHEAT PARK SAFELY Significant pulling in the car's traction. Gearbox overheated. Park the car immedi-
ately in a safe manner.
TRANSM. COOLING LET ENGINE RUN No drive due to overheated gearbox. Gearbox overheated. For fastest cooling:
Run the engine at idling speed with the gear
lever in the N or P position until the mes-
sage clears.
A For fastest cooling: run the engine at idling speed with the gear lever in the N or P position, until the message clears.
164
06 Starting and driving
Brake system
Brake servo Dampness can affect braking Bear in mind that driving with a trailer puts an
If the car is rolling or is being towed with the characteristics additional load on the car's brakes.
engine turned off, the brake pedal must be Brake components become wet when the car
depressed about 5 times harder than when the is driven in heavy rain, through pools of water Anti-lock braking system - ABS
engine is running. If the brake pedal is or when the car is washed. This may alter brake
The anti-lock braking system
depressed when the engine is started, you will pad friction characteristics so that there is a
(ABS) prevents the wheels from
feel the pedal drop. This is normal and due to delay before braking effect is noticed.
locking up during braking.
the brake servo becoming active. This may be Press the brake pedal lightly from time to time
more noticeable if the car has Emergency This means the ability to steer is
if driving for long stretches in rain or slushy
Brake Assistance (EBA). maintained and it is easier to swerve to avoid a
snow, as well as after setting off in very damp
hazard for example.
or cold weather. This warms up the brake pads
WARNING and dries off any water. This precaution is also After the engine has been started, the ABS will
The brake servo only works when the engine recommended before parking the car for a long perform a brief self-test at a speed of
is running. period in such weather conditions. about 20 km/h. This can be felt and heard as
pulses in the brake pedal.
NOTE If the brakes are used heavily To get the most out of the ABS:
When driving in the Alps or other roads with 1. Depress the brake pedal with full force.
If braking with the engine switched off,
press the brake pedal sharply once, not
similar characteristics, the car's brakes are Pulses will be felt.
repeatedly. heavily loaded even if the brake pedal is not 06
being depressed especially hard. 2. Steer the car in the direction of travel. Do
not release the pressure on the pedal.
Because speed is often low, the brakes are not
Brake circuits cooled as effectively as when driving on flat Practice braking with the ABS system in a traf-
This symbol illuminates if a brake roads at higher speed. fic-free area and in different weather condi-
circuit is not working. tions.
So as not to overload the brakes, shift down
If a fault should occur in one of the when driving downhill instead of using the foot The ABS symbol illuminates for 2 seconds if
circuits, it is still possible to brake brake. Use the same gear driving downhill as there was a fault in the ABS system when the
the car. The brake pedal will travel further and you would use driving uphill. This uses engine engine was last running.
may feel softer than normal. Harder pressure braking more efficiently so the foot brake is
on the pedal is needed to produce the normal only required for brief periods.
braking effect.
``
165
06 Starting and driving
Brake system
166
06 Starting and driving
The car is equipped with either STC or DSTC Reduced operation Operation
depending on market. The table shows the 1. Turn thumbwheel until the STC/DSTC
integral functions of the respective systems. menu is shown.
DSTC ON means that the system function
Function/system STC DSTC is unchanged.
Active Yaw Control X DSTC SPIN CONTROL OFF means that
system operation is reduced.
Spin Control X X
2. Press and hold the RESET button until the
Traction control sys- X X STC/DSTC menu is changed. 06
tem The system remains reduced until the
driver reactivates it or until the engine is
Active Yaw Control switched off - after the engine is started the
G029057
The function limits the driving and brake force next time DSTC is back in its normal mode
of the wheels individually in order to stabilise again.
the car.
Thumbwheel1
RESETbutton 1
1 No function in cars without trip computer, fuel-driven parking heater as well as stability and traction control system.
``
NOTE
DSTC ON is shown for several seconds on
Information
the display each time the engine is started.
ANTI-SKID SERVICE REQUIRED system • Flashing light means that the STC/DSTC
06 system is now being activated.
disabled due to a fault.
• Constant glow for two seconds means
Stop the car in a safe place and turn off the system check when the engine is started.
engine.
• Constant glow after starting the engine or
> If the message remains when the engine while driving means that there is a fault in
is restarted, drive to a workshop. An the STC/DSTC system.
authorised Volvo workshop is recom-
mended.
Park Assist*
``
Park Assist*
The system is automatically engaged when the Fault indicator Cleaning the sensors
car is started and the switch's On/Off lamp is If the information symbol illumi-
illuminated. If parking assistance is switched nates with constant glow and the
off with the button, the lamp goes out. display shows PARK ASSIST
SERVICE REQUIRED then park-
Front
ing assistance is disengaged. For
Front parking assistance is active at speeds
attention, contact a workshop - an authorised
below 15 km/h. The system is deactivated at
Volvo workshop is recommended.
higher speeds. When the speed is below
10 km/h the system is reactivated.
IMPORTANT
The distance covered to the front of the car is
about 0.8 metres. The signal for obstacles in In certain conditions the parking assistance
system may produce incorrect warning sig-
front comes from the front loudspeakers.
nals that are caused by external sound
Limitations sources that emit the same ultrasonic fre-
Front parking assistance cannot be combined quencies that the system works with.
with extra lights because the sensors are affec- Examples of such sources include horns, Parking assistance sensors.
ted by the extra lights. wet tyres on asphalt, pneumatic brakes and
The sensors must be cleaned regularly to
exhaust noises from motorcycles etc.
ensure that they work properly. Clean them
Rear
06
with water and car shampoo.
Rear parking assistance is activated when
reverse gear is engaged.
NOTE
The distance covered to the rear of the car is
about 1.5 metres. The signal for obstacles Dirt, ice and snow covering the sensors may
behind comes from the rear loudspeakers. cause incorrect warning signals.
Limitations
See the previous section Rear parking assis-
tance only.
NOTE
Rearview mirror with BLIS system. The lamp illuminates on the side of the car A = approx. 3.0 m, B = approx. 9.5 m.
BLIS camera where the system has detected the vehicle.
If the car is overtaken on both sides at the When BLIS operates
Indicator lamp same time then both lamps illuminate.
The system operates when the car is driven at 06
BLIS symbol a speed above 10 km/h.
BLIS advises the driver with a message if a fault
arises in the system. If for example the sys- Overtaking
WARNING tem's cameras are obscured then the BLIS The system is designed to react if you overtake
The system is a supplement to, not a indicator lamp flashes and a message is shown another vehicle at a speed of up to 10 km/h
replacement for, a safe driving style and use in the information display. In such cases, check faster than the other vehicle.
of the rearview mirrors. It can never replace and clean the lenses. If necessary, the system
the driver's attention and responsibility. The The system is designed to react if you are over-
can be switched off temporarily by pressing the
responsibility for changing lanes safely taken by a vehicle travelling up to 70 km/h
BLIS button see page 172.
always rests with the driver. faster than your vehicle.
``
WARNING Activating/deactivating ton to clear the text message. For more infor-
mation on messages, see page 58.
BLIS does not work in sharp bends.
BLIS does not work when the car is revers- BLIS system message
ing. Text on the dis- Specification
A wide trailer coupled to the car can conceal play
other vehicles in adjacent lanes. It can pre-
vent the vehicle in the screened area from BLIS ON The BLIS system is
being detected by BLIS. activated.
G018177
workshop. NOTE
BLIS OFF The BLIS system is If the BLIS indicator lamp illuminates on iso-
deactivated. lated occasions despite there being no Own shadow on large, light, smooth surface, e.g.
other vehicle within the blind spot then this noise barrier or concrete road surface.
does not mean that a fault has arisen in the
IMPORTANT system.
In the event of a fault in the BLIS system the
Repair of the BLIS system components
display shows the text BLIS SERVICE
must only be performed by a workshop - an
authorised Volvo workshop is recom-
REQUIRED.
mended.
Here are several examples of situations where
the BLIS indicator lamp may illuminate even if
Cleaning there is no other vehicle within the blind spot. Low sun in the camera.
In order to work most effectively the BLIS cam-
06
era lenses must be clean. The lenses can be
cleaned with a soft cloth or damp sponge.
Clean the lenses carefully so that they are not
scratched.
IMPORTANT
The lenses are electrically heated to melt ice
Reflection from shiny wet road surface.
or snow. If necessary, brush snow away
from the lenses.
174
06 Starting and driving
Move the gear selector to position N and • Open the variant with a recess using a NOTE
release the parking brake. coin or similar inserted in the recess,
turning it outwards. Then turn out the On certain cars with fitted towbar the towing
cover completely and remove it. eye cannot be secured in the rear mounting.
Towing eye In which case, secure the tow rope in the
• The second variant has a marking along towbar.
one side or in a corner: Press the mark-
ing with a finger and fold out the oppo- For this reason it is advisable to store the
towbar's towball in the car, see page 179.
site side/corner at the same time using
a coin or similar - the cover turns around
its axis and can then be removed.
Recovery
Screw the towing eye right in up to its Call a recovery service for recovery assistance.
flange. Turn in the towing eye firmly e.g.
using the wheel wrench. The car must always be towed with the wheels
rolling forward.
After use, unscrew the towing eye and
return it to its place.
IMPORTANT
Finish by refitting the cover onto the
Cars with automatic gearbox must only be
bumper. towed with drive wheels raised from the
road.
The towing eye is screwed into a threaded IMPORTANT 06
socket behind a cover on the right-hand side The towing eye is only designed for towing
of the bumper, front or rear. on roads - not for pulling the car unstuck or
out of a ditch. Call a recovery service for
Fitting the towing eye recovery assistance.
Take out the towing eye (1) that is located
under the floor hatch in the cargo area.
The cover for the towing eye's attachment
point is available in two variants which
must be opened in different ways:
175
06 Starting and driving
Start assistance
Starting with a donor battery 3. If the donor battery is in another car, switch WARNING
off the engine in the other car and ensure
that the cars do not touch one another. The battery can generate oxyhydrogen gas,
which is highly explosive. One spark, which
4. Connect the red jump lead between the can be generated if you connect the jump
positive terminal on the donor battery (1+) leads incorrectly, is sufficient to make the
and the positive terminal in your car (2+). battery explode.
5. Connect one end of the black jump lead to The battery contains sulphuric acid, which
can cause serious burns. If the acid comes
the donor battery's negative terminal (3-).
into contact with eyes, skin or clothing, flush
6. Connect the other end of the black jump with large quantities of water.
lead to the earthing point (4–) by the left- If acid splashes into the eyes, seek medical
hand strut tower. attention immediately.
7. Start the engine of the "donor car". Let the
engine run a few minutes at a speed slightly
higher than idle 1500 rpm.
If the battery in the car has become flat, you 8. Start the engine of the car with the flat bat-
can "borrow" electric current from either a sep- tery.
arate battery or from another car. Always make 9. Remove the jump leads, first the black and
06 sure the crocodile clips on the jump leads are then the red.
attached securely to eliminate sparks during
the start attempt. Make sure that none of the clamps on the
black jump lead comes into contact with
When jump starting the car, the following steps the battery's positive terminal or the clamp
are recommended to avoid risk of explosion: connected to the red jump lead.
1. Turn the remote control key to key position
0. IMPORTANT
2. Ensure that the other battery is 12 volt. Do not touch the crocodile clips during the
start procedure. There is a risk of sparks
forming.
176
06 Starting and driving
177
06 Starting and driving
IMPORTANT
See also the specific information on slow
driving with trailer for cars with the
Powershift automatic transmission on page
163.
06
Parking on a hill
1. Depress the foot brake.
2. Apply the parking brake.
3. Move the gear selector to parking position
P.
4. Release the foot brake.
• Move the gear selector to park position P
when parking an automatic car with a
178
06 Starting and driving
Towing equipment*
WARNING
If the car is fitted with a Volvo detachable
towbar:
• Follow the installation instructions care-
fully.
• The detachable section must be locked
G031118
G014589
with the key before setting off.
• Check that the indicator window shows
green. Towbar storage space.
An adapter is required if the car's towing
IMPORTANT bracket has 13 pin electrics and the trailer has
Important checks 7 pin electrics. Use an adapter cable approved
• The towbar's towball must be cleaned and Always remove the towbar after use and by Volvo. Make sure the cable does not drag 06
greased regularly. store it in the appointed location in the car, on the ground.
firmly fastened with its strap.
NOTE
If a towball hitch with vibration damper is
used, it is not necessary to grease the tow-
ball.
``
Towing equipment*
Specifications
G010387
G010388
G010393
1 Side member
2 Ball centre
Detachable towbar*
G020301
G020302
G017317
2. Ensure that the mechanism is in the 3. Check that the indicator window (3) shows
1. Remove the protective cover by first press- unlocked position by turning the key clock- red. If the window does not show red,
ing in the catch and then pulling the wise. press in and turn the locking wheel anti-
cover straight back . clockwise until you hear a click.
06
``
Detachable towbar*
G020304
G020309
G020307
4. Insert the towbar until you hear a click. 7. Check that the towbar is secure by pulling
it up, down and back.
IMPORTANT
Only grease in the ball for the towing hitch,
the remainder of the towbar should be clean
and dry.
G020306
Detachable towbar*
G020310
G020312
G020301
8. Safety cable. 2. Push in the locking wheel and turn it
1. Insert the key and turn it clockwise to the anticlockwise until you hear a click.
WARNING unlocked position.
Be sure to attach the trailer's safety cable to
the correct place. 06
``
Detachable towbar*
G020314
G017318
3. Turn the locking wheel down fully, until it 4. Push on the protective cover.
comes to a stop. Hold it in this position
while pulling the towbar rearward and
upward.
06
WARNING
Secure the towbar safely if it is stored in the
car, see page 179.
Loading
Correct light pattern for left or right- Halogen headlamps Headlamps with Active Bending Lights
hand traffic
G021421
G021422
G020317
186
06 Starting and driving
06
187
General.................................................................................................. 190
Tyre pressure........................................................................................ 194
Warning triangle* and spare wheel * .................................................... 195
Changing wheels................................................................................... 197
Emergency puncture repair* ................................................................ 199
General
190
07 Wheels and tyres
General
The reason for this is that tyres age and decom- wards in a straight line rather than having the tyres with little tread depth provide very poor
pose, even if they are hardly ever or never used. rear end skidding to one side, resulting in pos- grip in rain and snow.
The function can therefore be affected due to sible complete loss of control over the car. This
the tyre's constituent materials being broken is why it is important for the rear wheels never
Winter tyres
down. In such a case the tyre should then not to lose grip before the front wheels.
be used. This also applies to spare tyres, winter Volvo recommends winter tyres with specific
Wheels should be stored lying down or hanging winter tyre dimensions. Tyre dimensions are
tyres and tyres saved for future use. Examples
up, and not standing up. dependent on engine variant. When driving on
of external signs which indicate that the tyre is
unsuitable for use are cracks or discoloration. winter tyres, they must be fitted to all four
Tyres with tread wear indicators wheels.
The age of the tyre can be determined by the
DOT marking, see previous illustration. NOTE
Volvo recommends that you consult a Volvo
More even wear and maintenance dealer about which wheel rim and tyre types
The correct tyre pressure results in more even are most suitable.
wear, see page 194. Driving style, tyre pres-
sure, climate and road condition affect how Studded tyres
quickly your tyres age and wear. To avoid dif- Studded winter tyres should be run in gently for
ferences in tread depth and to prevent wear 500-1000 km, so that the studs settle properly
patterns arising, the front and rear wheels can into the tyres. This gives the tyre, and espe-
be switched with each other. A suitable dis- cially the studs, a longer service life.
G020323
tance for the first change is approx. 5000 km
and then at 10 000 km intervals. Volvo recom-
NOTE
mends that you contact an authorised Volvo
workshop for checking if you are uncertain Tread wear indicators. The legal provisions for the use of studded 07
about tread depth. If significant differences in Tread wear indicators are narrow treadless tyres vary from country to country.
wear (>1 mm difference in tread depth) bands across the width of the tread. On the
between tyres have already occurred, the least side of the tyre are the letters TWI (Tread Wear Tread depth
worn tyres must always be placed on the rear. Indicator). When the tyre's tread depth is down Road conditions with ice, slush and low tem-
Understeer is normally easier to correct than to 1.6 mm, the tread depth will be level in height peratures place considerably higher demands
oversteer, and leads to the car continuing for- with the tread wear indicators. Change to new on tyres than summer conditions. It is therefore
tyres as soon as possible. Remember that
``
191
07 Wheels and tyres
General
192
07 Wheels and tyres
General
wheel nuts are used in combination with wheel IMPORTANT be switched between front and rear positions,
covers, the locking wheel nut should be moun- never between left and right-hand sides, or
ted on the bolt nearest the air valve. Otherwise The car must never be driven fitted with vice versa.
the wheel cover cannot be fitted to the rim. more than one "Temporary Spare" wheel.
If the tyre is mounted incorrectly, the car's
braking characteristics and capacity to force
NOTE Summer and winter wheels rain, snow and slush out of the way are
Tighten the lockable wheel nuts to 110 Nm. adversely affected.
Tyres with the greatest tread depth should
always be fitted to the rear of the car (to
Spare wheel Temporary Spare* decrease the risk of skidding).
The spare wheel (Temporary spare) is only
intended for use temporarily and must be Volvo recommends that you contact an author-
replaced by an ordinary wheel as soon as pos- ised Volvo workshop for checking if you are
sible. The car's handling may be altered by the uncertain about tread depth.
use of the spare wheel. The spare wheel is
smaller than the normal wheel. The car's
ground clearance is affected accordingly. Pay
attention to high kerbs and do not machine
G020325
wash the car. If the spare wheel is fitted on the
front axle, you cannot use snow chains at the
same time. On all-wheel drive cars the drive on
The arrow shows the tyre's direction of rotation.
the rear axle can be disconnected. The spare
wheel must not be repaired. The correct tyre When summer and winter wheels are changed,
pressure for the spare wheel is stated in the see page 197, the wheels should be marked
07
tyre pressure table, see page 290. with which side of the car they were mounted
on, for example L for left and R for right. Tyres
IMPORTANT with a tread pattern which are designed to only
turn in one direction have the direction of rota-
Never drive faster than 80 km/h with a spare tion marked with an arrow.
wheel on the car.
The tyre must always rotate in the same direc-
tion throughout its lifespan. Tyres should only
Tyre pressure
194
07 Wheels and tyres
Warning triangle
Follow the regulations for the use of a warning Spare wheel* and jack * NOTE
triangle*. Place the warning triangle in a suita-
ble place with regard to the traffic. The car's original jack* Volvo recommends only using the jack* that
The original jack must only be used for chang- belongs to the car model in question, which
1. Undo the case containing the warning tri- ing wheels. The jack's thread should always be is indicated on the jack's label.
angle, it is secured with Velcro straps. Take
well greased. The spare wheel* plus jack* and The label also indicates the jack's maximum
the warning triangle from the case. lift capacity at a specified minimum lifting
wheel wrench* are stored under the floor in the
2. Lower the warning triangle's support legs. cargo area. height.
07
Ensure the warning triangle and its case are
firmly secured in the cargo area after use. Taking out the spare wheel
1. Fold the rear edge of the floor mat forward.
2. Release the spare wheel and lift it out.
3. Take out the jack* plus crank and the wheel
wrench*.
``
IMPORTANT
07
The tools and jack* must be stored in the
intended location in the car's cargo area
when not in use.
Changing wheels
G020332
G020331 selected, see page 215.
2. Apply the parking brake and engage
reverse gear, or position P if the car has an
automatic gearbox. WARNING
Set up the warning triangle if a wheel must be
3. Place chocks in front of and behind the Never position anything between the
changed at a busy location. Make sure that the
wheels which will remain on the ground. ground and the jack, nor between the jack
car and jack are on a firm horizontal surface.
Use heavy wooden blocks or large stones. and the car's jacking point.
WARNING 4. Cars with steel rims have removable wheel
covers. Prize off the wheel cover with the 6. There are two jacking points on each side
Check that the jack is not damaged, that the end of the wheel wrench, or pull it off by of the car. There is a recess in the plastic
threads are thoroughly lubricated and that it
is free from dirt. hand. cover at each point. Crank the foot of the
jack down so it is pressed squarely on the 07
5. Loosen the wheel nuts ½-1 turn anticlock-
ground. Check that the jack is seated cor-
wise with the wheel wrench.
rectly in the intended jacking point, as illus-
trated, and that the base is located directly
under it.
``
Changing wheels
The ground must be firm, smooth and level. 5. Put on the wheel cover (steel rim).
198
07 Wheels and tyres
Emergency puncture repair, general NOTE 1. Fold up the cargo area floor.
information 2. Lift up the emergency puncture repair kit.
The emergency puncture repair kit is only
intended for sealing tyres with a puncture in
the tread. Overview
WARNING
G020400
The emergency puncture repair kit is used to
You should not drive faster than 80 km/h
seal a puncture as well as to check and adjust
after the emergency tyre repair kit has been
the tyre pressure. It consists of a compressor used. Volvo recommends that you visit an Decal, maximum permitted speed
and a bottle with sealing fluid. The kit works as authorised Volvo workshop for inspection of
a temporary repair. The sealing fluid bottle the sealed tyre (maximum driving distance Switch
must be replaced before its expiration date and is 200 km). The staff there can determine
after use. whether or not the tyre can be repaired or if Cable
it needs to be replaced. 07
The sealing fluid effectively seals tyres punc- Bottle holder (orange cap)
tured in the tread.
Taking out the emergency puncture Protective cap
repair kit Pressure reducing valve
The emergency puncture repair kit with com-
pressor and tools are stored under the floor in Air hose
the cargo area.
``
``
07
07
203
Cleaning................................................................................................ 206
Touching up paintwork......................................................................... 210
Rustproofing......................................................................................... 211
204
CAR CARE
08 Car care
Cleaning
206
08 Car care
Cleaning
``
Cleaning
Cleaning the interior Treatment of stains on textile upholstery leather. This is a natural maturing of the leather
Only use cleaning agents and car care prod- and headliner and shows that it is a natural product.
ucts recommended by Volvo. Clean regularly A special fabric cleaning agent, available from To achieve best results Volvo recommends
and follow the instructions included with the authorised Volvo dealers, is recommended to cleaning and the application of protective
car care product. avoid impairing the fire retardant qualities of cream once to four times per year (or more if
the upholstery. necessary). The Volvo Leather Care kit is avail-
Vacuuming is important prior to using cleaning
agents. able from your Volvo dealer.
IMPORTANT
Carpets and cargo area Sharp objects and Velcro may damage the IMPORTANT
Remove inlaid carpets for separate cleaning of fabric upholstery.
the floor carpet and the inlaid carpets. Use a • Certain items of coloured clothing (for
example, jeans and suede garments)
vacuum cleaner to remove dust and dirt.
Treating stains on leather upholstery may stain the upholstery.
Each inlay mat is secured with pins. Volvo's leather upholstery is chromium-free • Never use strong solvents. Such prod-
Take hold of the inlay mat at each pin and and approved in accordance with the Oeko- ucts may damage fabric, vinyl and
lift the mat straight up. Tex 100 standard and is treated to preserve its leather upholstery.
original appearance.
Fit the inlay mat in place by pressing it in at
each pin. Leather upholstery ages and acquires a beau- Washing instructions for leather
tiful patina over time. The leather is refined and upholstery
processed so that it retains its natural charac-
WARNING 1. Pour the leather cleaner on the dampened
teristics. It is given a protective coating, but
Before setting off check that the inlaid mat regular cleaning is required in order to maintain sponge and squeeze out a strong foam.
in the driver area is firmly affixed and both characteristics and appearance. Volvo 2. Work the dirt away with gentle circular
secured in the pins in order to avoid getting offers a comprehensive product for the clean- movements.
caught adjacent to and under the pedals.
ing and treatment of leather upholstery which,
3. Dab accurately with the sponge on the
when used in accordance with the instructions,
A special textile cleaner is recommended for stains. Allow the sponge to absorb the
preserves the leather's protective coating.
stains on the floor mat after vacuuming. Floor stain. Do not rub.
After a period of use the natural appearance of
08 mats should be cleaned with agents recom- the leather will nevertheless emerge, depend- 4. Wipe off with soft paper or a cloth and
mended by your Volvo dealer! ing more or less on the surface texture of the allow the leather to dry completely.
208
08 Car care
Cleaning
Protective treatment of leather Group 1 (ink, wine, coffee, milk, sweat and
upholstery blood)
Vacuuming is important prior to using leather Use a soft cloth or sponge. Mix a 5%
care agents. ammonia solution. (For blood stains, use a
1. Pour a small amount of the protective solution of 2 dl water and 25g salt.)
cream on the felted cloth and massage in Group 2 (fats, oils, sauces and chocolate)
a thin layer of cream with gentle circular
movements on the leather. 1. Same procedure as group I.
2. Allow the leather to dry for 20 minutes 2. Polish with an absorbent paper or cloth.
before use. Group 3 (dry dirt, dust)
The leather has now been given improved pro- 1. Use a soft brush to remove the dirt.
tection against stains and improved UV pro-
tection. 2. Same procedure as group I.
209
08 Car care
Touching up paintwork
Paintwork Stone chips and scratches If the stone chip has penetrated to the
Paint is an important part of the car's rust- bare metal
proofing and should therefore be checked reg- 1. Apply a piece of masking tape over the
ularly. To avoid the onset of rust, damaged damaged surface. Then remove the tape to
paintwork should be rectified immediately. The remove any loose paint.
most common types of paintwork damage are 2. Stir the primer well and apply using a fine
stone chips, scratches, and marks on the brush or a matchstick. Apply paint using a
edges of wings and doors. brush once the primer is dry.
Colour code 3. For scratches, proceed as above, but
mask around the damaged area to protect
the undamaged paintwork.
4. After a few days, polish the touched-up
G020345
areas. Use a soft rag and a small amount
of lapping paste.
Materials
• Primer in a can
Data plate. • Spray can or touch-up pen1
Code for car colour • Masking tape.
It is important that the correct colour is used.
Minor stone chips and scratches
For product decal location, see page 278.
If the stone chip has not penetrated to the bare
metal and there is an undamaged colour coat,
08 you can paint straight after cleaning the dam-
aged area.
210
08 Car care
Rustproofing
08
211
Volvo service......................................................................................... 214
Self-maintenance.................................................................................. 215
Bonnet and engine compartment......................................................... 216
Oils and fluids....................................................................................... 218
Wiper blades......................................................................................... 224
Battery................................................................................................... 226
Replacing bulbs.................................................................................... 228
Fuses..................................................................................................... 234
212
MAINTENANCE AND SERVICE
09 Maintenance and service
09 Volvo service
IMPORTANT
For the Volvo warranty to apply, check and
follow the instructions in the Service and
Warranty Booklet.
214
09 Maintenance and service
Self-maintenance 09
Before starting work on the car Raising the car If you raise the car using a two-pillar workshop
lift, ensure that the front and rear lift arms are
Battery fixed under the lifting points. See preceding
Check that the battery cables are correctly illustration.
connected and tightened.
Never disconnect the battery when the engine Check regularly
is running (e.g. if replacing the battery). Check the following at regular intervals, for
Never use a quick charger to charge the bat- example, when refuelling:
tery. The battery cables must be disconnected • Coolant – The level must be between the
when charging the battery. MIN and MAX marks on the expansion
The battery contains acid that is both corrosive tank.
and toxic. It is therefore important to handle the • Engine oil – The level must be between the
battery in an environmentally correct manner. MIN and MAX marks.
Let your Volvo dealer assist you. • Power steering fluid – The level must be
between the MIN and MAX marks.
WARNING • Washer fluid – The reservoir should be well
NOTE
High output from the ignition system. The filled. Use washer antifreeze at tempera-
voltage in the ignition system is highly dan- Volvo recommends only using the jack that tures around freezing.
gerous. The ignition must therefore always belongs to the car model in question. If a
be switched off for work in the engine com- jack is selected other than the one recom- • Brake and clutch fluid – The level must be
mended by Volvo, follow the instructions for between the MIN and MAX marks.
partment.
use supplied with the equipment
Do not touch the spark plugs or ignition coils WARNING
when the ignition is on or the engine is hot.
If the car is raised with a workshop jack; posi- Bear in mind that the radiator fan may start
tion the jack against the front edge on the sub- automatically some time after the engine
frame. has been switched off.
Do not damage the splashguard under the Always have the engine cleaned by a work-
engine. Ensure that the jack is positioned so shop. There is a risk of fire if the engine is
hot.
that the car cannot slide off the jack. Always
use axle stands or similar.
215
09 Maintenance and service
G020793
The illustration shows a left-hand drive car.
1. Pull the handle on the far left under the WARNING Engine oil dipstick1
instrument panel. (In right-hand drive cars
the handle is on the far right.) You will hear Check that the bonnet locks properly when Radiator
when the catch releases. closed.
Radiator fan
2. Insert your hand under the centre of the Washer fluid reservoir (5-cyl.)
front edge of the bonnet and press the Engine compartment
safety catch to the right. Washer fluid reservoir (4-cyl.) Brake and clutch fluid reservoir (right-hand
3. Open the bonnet. drive)
Coolant expansion tank
Filler opening for engine oil1
Reservoir for the power steering fluid (con-
Brake and clutch fluid reservoir (left-hand
cealed behind the headlamp)
drive)
1 Engines with electronic oil level sensor have no dipstick (5-cyl. diesel).
216
09 Maintenance and service
Battery
Relay and fuse box, engine compartment
Air filter1
1 Engines with electronic oil level sensor have no dipstick (5-cyl. diesel).
217
09 Maintenance and service
Engine compartment decal for oil Checking the engine oil and oil filter
grade
G020338
Diesel engine.
Dipstick, petrol engines. Dipstick, 4-cyl diesel engines.
Filler pipe, engine oil.
IMPORTANT
Always use oil of the prescribed grade, see Volvo recommends Castrol oil products.
the engine compartment decal. Check the
oil level frequently and change the oil regu-
larly. The engine will be damaged if lower
grade oil is used or if the car is driven with
the oil level too low.
218
09 Maintenance and service
IMPORTANT Change the engine oil in accordance with the Checking the oil
intervals specified in the Service and Warranty
In order to fulfil the requirements for the Booklet.
engine's service intervals all engines are
filled with a specially adapted synthetic Using oil of a higher than specified grade is
engine oil at the factory. The choice of oil permitted. If the car is driven in adverse con-
has been made very carefully with regard to ditions, Volvo recommends using an oil of a
service life, starting characteristics, fuel higher grade than that specified on the decal,
consumption and environmental impact.
see page 218.
An approved engine oil must be used in
order that the recommended service inter- For capacities, see page 285 and onwards.
vals can be applied. Only use a prescribed Checking the oil level in a new car is especially
grade of oil (see the engine compartment important before the first scheduled oil change.
decal) for both filling and oil change, other-
wise you will risk affecting service life, star- Volvo recommends checking the oil level every
G020336
ting characteristics, fuel consumption and 2 500 km. The most accurate measurements
environmental impact. are made on a cold engine before starting. The
Volvo Car Corporation disclaims all war- measurement will be inaccurate if taken imme- The oil level must be within the area marked on the
ranty liability if engine oil of the prescribed diately after the engine is switched off. The dipstick.
grade and viscosity is not used. dipstick will indicate that the level is too low
Engine with oil dipstick1
because the oil has not had time to flow down
1. Ensure that the car is level. After switching
Volvo uses different systems for warning of into the oil sump.
off the engine it is important to wait
low/high oil level or low/high oil pressure. Cer- 5 minutes to allow the oil time to run back
tain variants have an oil pressure sensor, and to the sump.
then the lamp for oil pressure is used. Other
variants have an oil level sensor, and then the 2. Pull up and wipe the dipstick.
driver is informed via the warning symbol in the 3. Re-insert the dipstick.
centre of the instrument unit as well as by dis-
play texts. Certain models have both variants. 4. Pull it out and check the level.
Contact a Volvo dealer for more information.
219
09 Maintenance and service
5. If the level is close to MIN then 0.5 litres For engines with electronic oil level
should be added. If the level is significantly sensor
below, then an additional amount is
required.
6. If required, check the level again, do it after
driving a short distance. Then repeat steps
1 - 4.
WARNING
Never fill above the MAX mark. The level
should never be above MAX or below MIN
as this could lead to engine damage.
WARNING
If the message Oil service required is
shown, visit a workshop. The oil level may
be too high.
2 Engines with electronic oil level sensor have no dipstick (5-cyl. diesel).
220
09 Maintenance and service
G020335
WARNING
Do not fill more oil if filling level (3) or (4)
appears as shown in the illustration below. Location of washer fluid reservoir3.
The level must never be above MAX or The windscreen and headlamp washers share
below MIN, as this could lead to engine a common reservoir.
damage.
For capacities, see the table Fluids on page
287.
WARNING Filler cap on 4-cylinder engines and diesel.
Do not spill oil onto the hot exhaust manifold
Filler cap on 5-cylinder engines.
due to the risk of fire.
Add washer antifreeze during the winter so that
The figures 1-4 represent filling level. Do not fill the fluid does not freeze in the pump, reservoir
more oil if filling level (3) or (4) is shown. Recom- and hoses.
mended filling level is 4.
221
09 Maintenance and service
When topping up the coolant, follow the For capacities and for standards regarding
instructions on the packaging. It is important water quality, see page 287.
that the mixture of coolant concentrate and
water is correct for the prevailing weather con- Check the coolant regularly
ditions. Never top up with water only. The risk The level must lie between the MIN and MAX
of freezing increases with both too little and too marks on the expansion tank. If the system is
much coolant concentrate.
222
09 Maintenance and service
NOTE
Check the level frequently.
G020333
223
09 Maintenance and service
09 Wiper blades
Wiper blades Replacing the wiper blades, windscreen 1. Turn up the wiper arm.
2. Press the button located on the wiper
blade mounting and pull straight out (1),
parallel with the wiper arm.
3. Slide in (2) the new wiper blade until a
"click" is heard.
> Check (3) that the blade is firmly instal-
led and fold down the wiper arm.
G020330
NOTE
The wiper blades are different lengths. The
blade on the driver's side is longer than on
the other side.
G014732
Cleaning
For cleaning wiper blades and windscreen, see
page 206.
1. Fold out the wiper arm.
IMPORTANT
2. Detach the wiper blade by pulling it
Check the wiper blades regularly. towards the rear window.
Neglected maintenance shortens the serv-
G020329
ice life of the wiper blades. 3. Press the new wiper blade into position.
224
09 Maintenance and service
Wiper blades 09
225
09 Maintenance and service
09 Battery
226
09 Maintenance and service
Battery 09
227
09 Maintenance and service
09 Replacing bulbs
General Changing front bulbs 3. Pull the lamp housing to the side and then
All bulb specifications are given on page 292. forward.
The following list contains bulbs and point- 4. Unplug the connector by pressing down
source lamps that are specialised or unsuitable the clip with a thumb while moving out the
for changing except at a workshop: connector with the other hand.
G019599
• Active Bending Lights (ABL)
• Daytime running lights (DRL) in the spoiler
WARNING All front bulbs (except for fog lamps) are
changed by first removing the lamp housing
G019600
On cars equipped with Xenon lamps, head- from the engine compartment.
lamp replacement must be performed at a
workshop - an authorised Volvo workshop Removing the lamp housing
is recommended. The lamp must be han- 5. Lift out the lamp housing and place it on a
1. Remove the remote control key and turn
dled with extreme caution because it is soft surface to avoid scratching the lens.
equipped with a high voltage unit. the light switch to position 0.
2. Withdraw the lamp housing's locking pin. Fitting the lamp housing
IMPORTANT 1. Plug in the connector and refit the lamp
IMPORTANT housing and locking pin. Check that the pin
Never touch the glass part of the bulbs with is correctly inserted.
your fingers. Grease and oil from your fin- Do not pull the electrical cable, only the con-
gers are vaporised by the heat, coating the nector. 2. Check the lighting.
reflector and then causing damage.
The lamp housing must be plugged in and
secured in place before the lighting is switched
228
09 Maintenance and service
Replacing bulbs 09
on or the remote control key inserted into the Main beam, Halogen
ignition switch.
Dipped beam
G019133
G019136
Fitting a new bulb The illustration shows a halogen bulb.
G019131
``
229
09 Maintenance and service
09 Replacing bulbs
5. Refit the bulb holder. It can only be refitted 4. Press the bulb holder back on. A "click" is 2. Twist the bulb holder anticlockwise and
in one position. heard when the bulb holder is fitted cor- remove it.
rectly.
6. Refit the cover, located above the lamp 3. To remove the bulb from the bulb holder,
housing, by turning it clockwise. 5. Refit the cover, located above the lamp press the bulb in and turn it anticlockwise.
housing, by turning it clockwise.
7. Refit the lamp housing, see page 228. 4. Fit a new bulb and refit the bulb holder into
6. Refit the lamp housing, see page 228. the lamp housing.
Position/parking lamps 5. Refit the lamp housing, see page 228.
NOTE
A lamp equipped with "Active Bending Side marker lamps
Lights* has a position lamp (LED) which can-
not be replaced.
Direction indicators
G019145
G018050
1. Undo the lamp housing, see page 228.
2. Undo the cover, located above the lamp
housing, by turning it anticlockwise. 1. Undo the lamp housing, see page 228.
G019150
3. Withdraw the bulb holder and change the 2. Twist the bulb holder anticlockwise and
bulb. withdraw it. Replace the bulb.
3. Refit the bulb holder. It can only fit in one
1. Undo the lamp housing, see page 228.
position.
Replacing bulbs 09
4. Refit the lamp housing, see page 228. 6. Fit a new bulb by turning clockwise. (The 3. The bulbs are located in separate bulb
profile of the bulb holder corresponds to holders.
the profile of the foot of the bulb.)
Front fog lamps 4. Unplug the connector from the bulb holder.
7. Refit the bulb holder. The TOP mark on the
5. Press the catches together and pull out the
bulb holder must always be upward.
bulb holder.
6. Replace the bulb.
Removing the bulb holder
7. Plug in the connector.
8. Press the bulb holder into place and refit
the cover (A or B).
NOTE
If an error message remains after the broken
bulb has been replaced then we recom-
G019605
G019166
2. Undo the cover by inserting a screwdriver
as illustrated (vertically) and continue to
press vertically in order to undo the clip All bulbs in the rear lamp cluster are replaced
inside the cover. from inside the cargo area.
3. Grip the edge of the cover and pull straight 1. Switch off all lights and turn the remote
out. control key to position 0.
4. Unscrew the lamp housing screw and pull 2. Remove the cover (A or B) in the left/right-
it out. hand panel to access the bulbs.
5. Turn the bulb anticlockwise and remove it.
``
231
09 Maintenance and service
09 Replacing bulbs
Location of the bulbs in the rear lamp Brake light (LED) Number plate lighting
Position lamp
Position/parking lamps
Direction indicators
Reversing lamp
Rear fog lamp (one side)
NOTE
The rear fog lamp only illuminates in the left
G014849
rear light cluster on a left-hand drive car and
in the right on a right-hand drive.
232
09 Maintenance and service
Replacing bulbs 09
G014852
G020253
1. Insert a screwdriver and gently turn so that Removing the mirror glass
the lamp housing comes loose. 1. Insert a screwdriver underneath the lower
2. Remove the blown bulb. edge, in the centre. Carefully prize up the
lug on the edge.
3. Fit a new bulb.
2. Insert the screwdriver underneath the edge
on the left and right-hand sides (by the
black rubber sections), and prize carefully
so that the glass comes loose in the lower
edge.
3. Carefully detach and lift aside the entire
mirror glass and cover.
4. Remove the blown bulb and replace it with
a new one.
09 Fuses
General WARNING
All electrical functions and components are
Never use a foreign object, or a fuse with an
fused to protect the car's electrical system amperage higher than that specified when
from damage by short circuiting and overload- replacing a fuse. This could cause signifi-
ing. cant damage to the electrical system and
possibly lead to fire.
The fuses are in two different locations in the
car:
• Relay/Fuse box in the engine compart-
ment.
• Relay/Fuse box in the passenger compart-
ment.
Changing
If an electrical component or function does not
work, it may be because the component's fuse
was temporarily overloaded and blew.
1. Look in the fuse diagram to locate the fuse.
2. Pull out the fuse and check from the side
to see whether the curved wire has blown.
3. If this is the case, replace it with a new fuse
of the same colour and amperage.
Each fuse box has space for several spare
fuses. If the same fuse fails repeatedly then
there is a fault in the component. In which case,
Volvo recommends that you visit an authorised
Volvo workshop for this to be checked.
234
09 Maintenance and service
Fuses 09
G007446
The fuse box has 36 fuse positions. Be sure to
replace a blown fuse with a new fuse of the
same colour and amperage.
• Fuses 19-36 are of the "Mini Fuse" type.
• Fuses 7-18 are of the "JCASE" type and
should be replaced by a workshop.1
• Fuses 1-6 are of the "Midi Fuse" type and
must only be replaced by a workshop.1
On the inside of the cover there are tweezers
that facilitate the procedure for the removal
and fitting of fuses.
235
09 Maintenance and service
09 Fuses
G020250
1. Cooling fan 50 A 8. ABS valves 20 A 17. Windscreen wipers 30 A
Fuses 09
23. Engine control module (5-cyl. 32. Injectors (5-cyl. petrol), Turbo 35. Relay coil, relay, climate con-
petrol), Transmission control control valve (5-cyl. diesel), trol system, PTC element, oil
module (5-cyl.) 10 A Oil level sensor (5-cyl. diesel) trap (5-cyl. petrol), Mass air
flow sensor (5-cyl. petrol),
Transmission control module Control valve, fuel flow
Turbo control valve (5-cyl.
(4-cyl.) 15 A (DRIVe), Mass air flow sensor
petrol), Solenoids, variable
(DRIVe), Control motor turbo
24. Heated fuel filter (5-cyl. die- valve timing (5-cyl. petrol),
(DRIVe) 10 A
sel), PTC element, oil trap (5- Injectors (2.0 l petrol), EVAP
cyl. diesel) 20 A 33. Vacuum pump (5-cyl. petrol), valve (2.0 l petrol), Valve, air/
Relay coil, relay, vacuum fuel mixture (2.0 l petrol), Con-
25. Central electronic module pump (5-cyl. petrol), Engine trol valve, fuel pressure (5-cyl.
(CEM) (Start/Stop) 10 A control module (5-cyl. diesel), diesel), Engine control mod-
Heated fuel filter (DRIVe) 20 A ule (5-cyl. diesel), Engine EGR
26. Ignition switch 15 A (DRIVe) 15 A
34. Ignition coils (petrol), Pres-
27. A/C compressor 10 A sure switch, climate control 36. Engine control module (petrol,
system (5-cyl.), Control mod- DRIVe), Accelerator pedal
28. Reserve –
ule, glow plugs (5-cyl. diesel), position sensor (5-cyl. diesel),
29. Fog lamp, front EGR emission control (5-cyl. Lambda-sond (5-cyl. diesel) 10 A
diesel), Fuel pump (DRIVe),
Daytime running lights (DRL)* 15 A
Lambda-sond (DRIVe),
30. Coolant pump (Start/Stop) 10 A Engine control module (Start/
Stop), Relay coils, relays
31. Voltage regulator, alternator Start/Stop 10 A
(4-cyl. petrol) 10 A
``
09 Fuses
G020601
The fuse box has 50 fuse positions. The fuses completely. The fuse box can be fully
are located under the glovebox. The box also unhooked.
provides space for several spare fuses. Tools
4. Close the fuse box in the reverse order.
for fuse replacement are located in the relay/
fuse box in the engine compartment, see 5. Remove the pins from the centre of the
page 235. clips. Fit the trim and the clips. Reinsert the
pins into the clips. This expands the clips
Replacing fuses and secures the trim.
1. Remove the trim concealing the fuse box
by pressing in the pin in the centre of the
clips (1) about one cm and then withdraw-
ing the clips.
2. Turn the two wing screws (that secure the
fuse box) (2) anticlockwise and remove
them.
3. Lower the fuse box (3) half way. Pull it
towards the seat until it stops. Lower it
238
09 Maintenance and service
Fuses 09
43. Phone*, Audio system, 48. Washer, rear window 15 A 54. Parking assistance*,
RTI*, Bluetooth* 15 A Xenon* 10 A
49. SRS system 10 A
44. SRS system, Engine con- 55. Control module Keyless* 20 A
trol module (5-cyl, DRIVe) 10 A 50. Reserve –
56. Remote control receiver,
45. Electrical socket, passen- 51. PTC element, air pre- Siren* 10 A
ger compartment 15 A heater*, Relay coil, relay,
heated fuel filter (5-cyl. 57. Data link connector
46. Passenger compartment, diesel), AWD 10 A (DLC), brake light switch 15 A
glovebox and courtesy
lighting 5A 52. Transmission control 58. Main beam, right, Relay
module, ABS system 5A coil, relay, auxiliary
47. Interior lighting, Remote lamps* 7.5 A
controlled garage door 53. Power steering 10 A
opener* 5A 59. Main beam, left 7.5 A
``
09 Fuses
60. Seat heating (driver's 73. Sunroof*, Overhead con- 85. Power seat, driver 25 A
side) 15 A sole for interior lighting,
Seatbelt reminder, rear, 86. Interior lighting, cargo
61. Seat heating (passenger Dimming, interior rear- area lighting, power
side) 15 A view mirror* 5A seats, fuel level display
(2.0F) 5A
62. Sunroof* 20 A 74. Fuel pump 15 A
63. Supply to rear right door 20 A 75. Reserve –
64. Satellite radio* 5A 76. Reserve –
65. Audio, Infotainment 5A 77. Electrical socket cargo
66. Audio, Infotainment, Cli- area, Control module,
mate control system 10 A accessories* 15 A
09
241
General.................................................................................................. 244
Audio functions..................................................................................... 246
Radio functions..................................................................................... 250
CD functions ........................................................................................ 255
Menu structure – audio system............................................................. 258
Phone functions*................................................................................... 259
Menu structure – phone*....................................................................... 266
Bluetooth handsfree*............................................................................ 269
General
Infotainment system system can be easily operated using the con- • EXIT (6) leads back one step in the menu
trol panel or the steering wheel keypad*, see structure. A long press on EXIT will exit the
10 page 73. The display (2) shows messages and menu system.
information on the current function.
Shortcuts
Menu options are numbered and can also be
Audio system selected directly with the keypad (3). So first
press MENU and then the figure/figures for the
On/Off
desired menu option.
POWER (1) starts/switches off the audio sys-
tem. If the audio system is active when the
remote control key is turned to position 0 then Equipment
it continues to be active until the remote control The audio system can be equipped with differ-
key is removed from the ignition switch. The ent options and different versions. There are
G020245
audio system is started automatically the next three audio system versions:
time the remote control key is turned to posi-
tion I.
• Performance,
POWER - Pushbutton, audio system on/ • High Performance* or
off • Premuim Sound*
Menus
Display However, FM radio with RDS, AM radio and CD
Some infotainment system functions are con-
trolled via a menu system. The current menu player are included in all audio systems.
Keypad
level is shown at the top right of the display.
MENU - Goes to the menu system Menu options are shown in the middle of the
Navigation buttons display.
General
1 Premium Sound.
245
10 Infotainment system
Audio functions
Audio controls ume adjusts automatically depending on vehi- The AUX and USB inputs enable the connec-
cle speed, see page 249. tion of an external audio source, e.g. an
10 iPod1 or MP3 player.
Audio source selection
Repeatedly pressing AM/FM switches If you choose to connect an iPod, MP3 player
between FM1, FM2 and AM. or a USB memory stick to the USB connection
then you can control the media via the car's
Repeatedly pressing MODE switches between audio controls.
CD, USB and AUX.
Use the MODE button to select the external
audio source you wish to use.
External audio sources
1. If USB is selected then Connect device is
General shown in the display.
2. Connect your iPod, MP3 player or USB
memory stick to the USB connection in the
centre console's storage compartment
VOLUME - Knob (see preceding illustration).
AM/FM – Audio source selection > The text Loading appears on the dis-
play when the system loads the file
MODE - Audio source selection, CD, AUX structure on the storage media. This
and USB (e.g. iPod)1 takes a while.
TUNING - Knob When the loading is finished the track informa-
tion is shown on the display and it is possible
SOUND - Button
to select the track required.
Navigation button - Menus Track selection can take place in the following
three ways:
Volume AUX input
Use VOLUME (1) or the steering wheel keypad
to regulate the volume, see page 73. Audio vol- USB input*
1 USB only applies for High Performance and Premium Sound. The iPod trademark belongs to Apple Computer Inc.
Audio functions
``
Audio functions
G021216
and activating/deactivating are sep-
Three channel stereo or Pro Logic II must arate for each audio source. Adjusting equalizer
be activated before adjustment is possible, 1. Press MENU and then ENTER.
see under the heading Activating/deacti- The Dolby icon in the display indicates that
Dolby Pro Logic II is active. There are three 2. Scroll to Audio settings… and press
vating surround sound below.
different settings for surround sound: ENTER.
• SURROUND2 - Level for surround. Pro
• Dolby Pro Logic II 3. Scroll to Equalizer front… or Equalizer
Logic II must be activated before adjust-
ment is possible, see under the heading rear… and press ENTER.
• 3 channel
Audio settings below. 4. The graphic on the display indicates the
• Off - 2 channel stereo. audio level of the frequency in question.
Activating/deactivating the subwoofer
Activating/deactivating surround sound 5. Adjust the level with TUNING (4) or up/
• Press MENU and then ENTER. 1. Press MENU and then ENTER. down with the navigation button. Addi-
• Scroll to Audio settings… and press tional frequencies can be selected using
ENTER. 2. Scroll to Audio settings… and press
ENTER. the left/right navigation button.
• Scroll to Subwoofer and press ENTER.
3. Scroll to Surround FM…, Surround 6. Save with ENTER or EXIT to exit without
AM…, Surround CD…or Surround saving the settings.
AUX… and press ENTER.
4. Scroll to Dolby Pro Logic II3, 3 channel
or Off and press ENTER.
2 Premium Sound.
3 Not available in AM and FM mode.
4 Certain audio systems.
248
10 Infotainment system
Audio functions
Automatic volume control5 are only intended for the user to be able to
The auto volume control function allows the adapt the sound reproduction according to
personal taste. 10
audio volume to increase as the speed of the
car increases. There are three levels to choose
from: Low, Medium and High.
5 Not Performance
Radio functions
250
10 Infotainment system
Radio functions
``
251
10 Infotainment system
Radio functions
For further programme interruption settings, 3. Scroll to Advanced radio settings… and Activating/deactivating News
see EON and REG see page 253. The pro- press ENTER. 1. Press MENU and then ENTER.
10 gramme functions are modified via the menu
4. Scroll to TP and press ENTER. 2. Scroll to News and press ENTER.
system, see page 244.
5. Scroll to TP station… and press ENTER. News from current station/all stations
Alarm > Either TP from current station or TP The radio can interrupt with news from only the
This function is used to warn of serious acci- set (current) station or from all stations.
from all stations is shown on the dis-
dents and catastrophes. The alarm cannot be
play. 1. Select an FM station.
temporarily interrupted or deactivated. The
message ALARM! appears on the display 6. Press ENTER. 2. Press MENU and then ENTER.
when an alarm message is transmitted.
Activating/deactivating TP search 3. Scroll to Advanced radio settings… and
Traffic information – TP TP search is useful during long journeys while press ENTER.
This function allows traffic informa- an audio source other than the radio is being 4. Scroll to News station… and press
tion broadcast within a set station's played. The function automatically searches ENTER.
for traffic information within different
G021220
G021222
such as Pop music and Serious
The radio can interrupt with traffic information News classic. The PTY symbol indicates
from only the set (current) station or from all This function allows news broad- that the function is active. This function allows
stations. casts within a set station's programme types broadcast within a set sta-
G021221
RDS network to break through. The tion's RDS network to break through.
1. Select an FM station.
message News shows that the func-
2. Press MENU and then ENTER. tion is active. Activating/deactivating PTY
1. Select FM1 or FM2 with FM/AM.
252
10 Infotainment system
Radio functions
2. Press MENU and then ENTER. Display of programme type Automatic frequency update – AF
3. Scroll to PTY and press ENTER. The programme type of the current station can The AF function selects one of the strongest
10
be shown on the display. transmitters for a set station. The radio may
4. Scroll to Select PTY… and press sometimes need to search through the entire
ENTER. FM wavelength to find a strong transmitter. If
NOTE
> A list of programme types appears: this occurs, the radio mutes and PI Seek
Current affairs, Information etc. The Not all radio stations support this function.
Press EXIT to cancel. appears in the display.
PTY function is activated by selecting
programme types and deactivated by Activating/deactivating display Activating/deactivating AF
clearing all PTYs. 1. Press MENU and then ENTER. 1. Press MENU and then ENTER.
5. Select the desired programme types or 2. Scroll to PTY and press ENTER. 2. Scroll to Advanced radio settings… and
Clear all PTY… press ENTER.
3. Scroll to Show PTY and press ENTER.
Search PTY 3. Scroll to AF and press ENTER.
This function searches the entire wavelength
for the selected programme type.
Radio text
Some RDS stations transmit information on Regional radio programmes – REG
1. Activate PTY. programme content, artists, etc. This informa- This function causes the radio to con-
2. Press MENU and then ENTER. tion can be shown on the display. tinue with a regional transmitter even
G021223
if its signal strength is low.
3. Scroll to PTY and press ENTER. Activating/deactivating radio text Regional indicates that the function
4. Scroll to Search PTY and press ENTER. 1. Press MENU and then ENTER. is active. The regional function is normally
2. Scroll to Radio text and press ENTER. deactivated.
If the radio finds any of the selected pro-
gramme types, >| To seek appears on the dis- Activating/deactivating REG
play. Press the navigation button to con- 1. Press MENU and then ENTER.
tinue searching for another broadcast of the 2. Scroll to Advanced radio settings… and
selected programme types. press ENTER.
3. Scroll to Regional and press ENTER.
``
253
10 Infotainment system
Radio functions
254
10 Infotainment system
CD functions
> An empty position is marked on the dis- When a CD containing audio files is inserted
play. The text Insert disc shows that a into the player the disc's folder structure is loa-
Navigation button – Fast forward/rewind, new disc can be inserted. The ded in. It may take a while before playback
track selection and menus CD changer can hold up to 6 CD discs. starts due to the quality of the disc.
CD changer position selection* 2. Inserting a CD in the CD changer. Navigation and playback
CD eject If a disc with audio files is inserted in the
CD insertion/eject
A CD will stay in the ejected position for CD player then the disc's folder structure is
CD insertion/eject slot approx. 12 seconds. Following which it is re- shown by pressing ENTER. The folder struc-
inserted in the player and playback continues. ture is navigated in the same way as the audio
MODE - Selection of audio source (CD, system's menu structure. Audio files have the
AUX, USB*) Eject individual discs by pressing the eject but-
ton (3). symbol and folders have the symbol .
TUNING - Knob for track selection Start audio file playback with ENTER.
Eject all discs with a long press on the eject
button. The entire magazine is emptied disc by When the playback of a file is finished the play-
Starting playback (CD player)
disc. The message EJECT ALL is shown in the back of the other files in the same folder con-
If a music CD is in the player when the audio
display. tinues. Folder change takes place automati-
system is in CD mode then playback is started
``
CD functions
cally when all files in the current folder have NOTE Activating/deactivating, random (CD
been played back. changer)
10 It is only possible to scroll between random
Press left/right on the navigation button if the If a normal music CD is being played:
CD tracks 1 on the current disc.
display is not wide enough to show the whole 1. Press MENU and then ENTER.
audio file name.
Different messages appear on the display 2. Scroll to Random and press ENTER.
Fast-wind/change CD tracks and audio depending on which random function has been
3. Scroll to Single disc or All discs and press
files selected:
ENTER.
Short presses right/left on the navigation but- • RANDOM means that the tracks from only
ton are used to scroll between one music CD are played The option All discs only applies to the music
CD tracks/audio files. Long presses are used CDs in the changer.
• RND ALL means that all tracks on all
to fast-wind CD tracks/audio files. TUNING (or music CDs in the CD changer are played. If a CD with audio files is being played:
the steering wheel keypad) can also be used
for this purpose. • RND FLD means that the audio files in a 1. Press MENU and then ENTER.
folder on the current CD are played.
2. Scroll to Random and press ENTER.
Scan CD Activating/deactivating, random (CD
This function plays the first 10 seconds of each 3. Scroll to Single disc or Folder and press
player)
CD track/audio file. Press SCAN to activate. ENTER.
If a normal music CD is being played:
Interrupt with EXIT or SCAN to continue play- The function is deactivated when another CD
back of the current CD track/audio file. 1. Press MENU and then ENTER.
is selected.
2. Scroll to Random and press ENTER.
Random Disc text
This function plays the tracks in random order. If a disc with audio files is being played: If title information is stored on a music CD then
The random CD tracks/audio files can be scrol- 1. Press MENU and then ENTER. it can be shown on the display2.
led through in the normal way.
2. Scroll to Random and press ENTER. Activating/deactivating
3. Scroll to Folder or Disc and press 1. Start CD playback.
ENTER. 2. Press MENU and then ENTER.
3. Scroll to Disc text and press ENTER.
256
10 Infotainment system
CD functions
CDs
Using low quality CD discs could result in poor
or non-existent sound. 10
IMPORTANT
Only use standard discs (12 cm in diameter).
Do not use CD discs with adhesive disc
labels. The heat in the CD player may cause
the label to come off, damaging the
CD player.
257
10 Infotainment system
Overview 4. TP 3. TP
FM MENU 5. Disc text 4.* Audio settings…
10
1. News 6.* Audio settings… USB MENU*
2. TP CD MENU 1. Playlist
3. PTY… For CD changer* with CD disc 2. Random…
4. Radio text selected.
3. News
5. Advanced radio settings… 1. Random…
4. TP
6.* Audio settings… 2. News
5. Track information
AM MENU 3. TP
6. Audio settings…
1.* Audio settings… 4. Disc text
Phone functions*
10
Phone functions*
G020244
SIM card reader With the IDIS system (Intelligent Driver
Information System), incoming phone calls and
SMS messages can be delayed so that con-
General centration can be focused on driving when IDIS The phone can only be used with a valid SIM
determines that the traffic situation requires a card Subscriber Identity Module. Cards are
• Always put traffic safety first. available from various network operators. In
high level of attention.
• If the driver needs to use the privacy hand- the event of problems with the card, contact
set*, park the car in a safe place first. Incoming calls and SMS messages can be your network operator.
• Switch off the phone system when refuel- delayed 5 seconds before they are diverted. If
ling the car. the current traffic situation still requires a high
NOTE
level of attention from the driver then the
• Switch off the system near blasting work. incoming call is diverted to the voice mail. The built-in phone cannot read 3G type SIM
• Volvo recommends that an authorised Missed calls are shown in the display. cards (3G only). Combined 3G/GSM cards
Volvo workshop carries out phone system work. Contact your network operator if a
servicing. IDIS be disconnected using menu function 6.5, replacement SIM card is required.
see page 266.
Phone functions*
G019809
G020243
the SIM card holder.
4. Carefully press in the SIM card holder.
Centre console control panel.
When the phone is active, the steering wheel
VOLUME - Control the background vol- keypad is locked to phone functions. To con-
Menus ume from the radio, for example, during a trol the audio system, the phone must be in
Page 266 describes how to control phone call standby mode (standby).
functions with the menu system.
Number and letter buttons
ENTER – Works the same as on the control
MENU - Opens the main menu panel
Traffic safety
For safety reasons, parts of the phone menu EXIT – Works the same as on the control
EXIT - End/refuse calls, clear entered char-
system cannot be accessed at speeds in panel
acters
excess of 8 km/h. Call volume – Increase/decrease
Navigation button – Scroll in menus and
character rows Navigation buttons – Scroll in menus
ENTER – Accept calls. A press of the but-
ton reveals latest dialled numbers
PHONE - On/off and standby mode
``
Phone functions*
Phone functions*
``
Phone functions*
6. Scroll to SIM card or Phone memory and 4. Enter the first few letters of the item and 6. Enter the first few letters of the item and
press ENTER. press ENTER, or simply press ENTER. press ENTER, or simply press ENTER.
10
Searching for contacts in the phone book 5. Scroll to the item to be erased and press 7. Scroll to an item and press ENTER.
Use the down arrow of the navigation button ENTER.
8. Hold EXIT depressed to leave the menu
instead of MENU for direct access to the
6. Scroll to Erase and press ENTER. system.
Search menu.
Erase all contacts Calling using speed dial
1. Press MENU. 1. Press MENU. Briefly press the required keypad button,
2. Scroll to Phone book… and press 2. Scroll to Phone book… and press followed by ENTER.
ENTER. ENTER.
3. Scroll to Search and press ENTER. NOTE
3. Scroll to Erase SIM or Erase phone and
4. Enter the first few letters of the item and press ENTER. It takes a short time before speed dialling
press ENTER, or simply press ENTER. becomes available after the phone has been
If required, enter phone code. The factory-set activated.
5. Scroll to an item and press ENTER. default code is 1234.
Copying entries between the SIM card Speed dial To use the speed dial function Speed dial…
and Phone book A keypad button (1–9) can be used as a speed must be activated in the Phone book… menu,
1. Press MENU. dial number for a contact in the phone book. see page 268.
2. Scroll to Phone book… and press 1. Press MENU.
ENTER. Calling from the phone book
2. Scroll to Phone book… and press 1. Press MENU.
3. Scroll to Copy all… and press ENTER. ENTER.
4. Scroll to SIM to phone or Phone to SIM 2. Scroll to Phone book… and press
3. Scroll to Speed dial… and press ENTER.
and press ENTER. ENTER.
4. Scroll to Select numbers and press > All contacts in the phone book memory
Deleting contacts from the phone book ENTER. are displayed. The number of contacts
1. Press MENU.
5. Scroll to the digit of the keypad button for displayed can be reduced by entering
2. Scroll to Phone book… and press the speed dial number and press ENTER. part of the contact's name.
ENTER. 3. Scroll to a contact and press ENTER.
3. Scroll to Search and press ENTER.
Phone functions*
1 A maximum of 5 phones.
``
operator for information on message settings. 4.6.2 When busy 6.1.2. Manual select
Normally, these settings should not be altered.
10 4.6.3. Not answered 6.2. SIM security
3.3.1. SMSC number Select if the PIN code should be on, off or if the
4.6.4. Not reachable
3.3.2. Validity time… phone should automatically give the PIN code.
4.6.5. Fax calls
3.3.3. Message type… 6.2.1. On
4.6.6. Data calls
6.2.2. Off
4. Call settings 4.6.7. Cancel all
6.2.3. Automatic
4.1. Send my number
5. Change phone
Displays or hides your phone number to/from 6.3. Edit PIN code
the person you call. Contact your network 5.1. Car phone Change PIN code. Write down and save the
operator regarding ex-directory numbers. Select the built-in phone. code in a safe place.
4.2. Call waiting 5.2. Add phone 6.4. Sounds and volume
Be alerted during a phone call that there is Add mobile phones to the list Added phones. 6.4.1. Ring volume
another incoming call. 5.3-7. Added phones Adjust the ring tone volume.
4.3. Auto answer Select to connect to one of the added phones
(up to 5 phones). 6.4.2. Ring signals…
Automatically answers incoming calls.
4.4. Auto redial There are seven different ring tones.
Automatically calls a previously engaged num- NOTE 6.4.3. Mute radio
ber. The menu above only applies to cars with The radio can be switched off/on.
4.5. Voice mail number BluetoothTM handsfree.
6.4.4. Message beep
Stores voice mail number.
4.6. Call divert 6. Phone settings 6.5. IDIS
Choose when and what type of calls are to be 6.1. Selecting network If the IDIS function is deactivated, incoming
diverted to a specified phone number. Choose a network automatically or manually. calls are not delayed, regardless of the driving
The selected network is shown in the display in situation.
4.6.1. All calls
the phone's basic mode. 6.6. Reset phone settings
This setting only applies during the call in pro-
6.1.1. Automatic Reset the system's factory settings.
gress.
Bluetooth handsfree*
``
Bluetooth handsfree*
4. Choose one of the mobile phones in the the mobile phone can be controlled from the NOTE
audio system display. audio system.
10 Some mobile phones require that the
5. Enter the number series shown in the audio To call changeover from handsfree is confirmed
system display via the mobile phone key- 1. Make sure that the text PHONE is shown from the phone's keypad.
pad.
at the top of the display and that the
Alternative 2 - via the phone's menu system symbol is visible. Making and receiving calls
1. Activate the handsfree function with 2. Dial the number or use the phone book,
PHONE. If there is a phone connected, see page 272. Incoming call
disconnect the connected phone. Calls are accepted with ENTER even if the
3. Press ENTER. audio system is in CD or FM mode for example.
2. Search with the phone's BluetoothTM, see Refuse or end with EXIT.
The call is interrupted with EXIT.
the mobile phone's manual.
3. Select My Car in the list of units detected Disconnecting the mobile phone Auto answer
Automatic disconnection takes place if the The automatic answer function means that
in your mobile phone.
mobile phone moves out of the audio system's calls are accepted automatically. Activate/
4. Enter the PIN code '1234' into the mobile range. For more information on connection, deactivate under Phone Menu… Call
phone when prompted for the PIN code. see page 271. options… Automatic answer.
5. Select to connect to My Car from the Manual disconnection takes place by deacti-
mobile phone. In-call menu
vating the handsfree function with one long
Press MENU or ENTER during an ongoing call
The mobile phone is registered and connected press on PHONE. The handsfree function is
to access the following functions:
automatically to the audio system while the text also deactivated when the engine is switched
Synchronising appears on the display. For off or when a door is opened1. • Mute microphone - audio system micro-
more information on how mobile phones are phone is muted.
When the mobile phone has been discon-
registered, see page 271. nected an ongoing call can be continued with • Transfer call to mobile - the call is trans-
When the connection is established the symbol the mobile phone's built-in microphone and ferred to the mobile phone.
is shown and the mobile phone's speaker.
BluetoothTM name is shown in the display. Now
Bluetooth handsfree*
Bluetooth handsfree*
Bluetooth handsfree*
twice for the second etc. Continue pressing for 3. Bluetooth… Menu structure - BluetoothTM
more characters, see the table on page 263. handsfree with built-in phone
3.1. Change phone 10
A short press on EXIT deletes an input char- 1. Call register…
3.1.1. Add phone
acter. One long press on EXIT clears all input 1.1. Last 10 missed calls
characters. / on the navigation button 3.1.2–6.Added phones3
1.2. Last 10 received calls
scrolls between the characters. 3.2. Remove phone
1.3. Last 10 dialled calls
3.3. Connect fr. mobile phone
Menu structure - BluetoothTM 2. Phone book…
3.4. Car Bluetooth info
handsfree 2.1. Search
4. Call options…
NOTE 2.2. Copy fr. mobile phone
4.1. Automatic answer
The menu for BluetoothTM handsfree is 3. Bluetooth…
4.2. Voice mail number
available in two variants. For cars with only 3.1. Remove phone
BluetoothTM handsfree and for cars with 5. Phone settings…
built-in phone and BluetoothTM handsfree. 3.2. Connect fr. mobile phone
5.1. Sounds and volume…
3.3. Car Bluetooth info
5.1.1. Ring volume
1. Call register… 4. Call options…
5.1.2. Ring signals…
1.1. Last 10 missed calls 4.1. Automatic answer
5.1.3. Mute radio
1.2. Last 10 received calls 4.2. Voice mail number
5.2. Synchronise phone book
1.3. Last 10 dialled calls 5. Change phone
2. Phone book… 5.1. Carphone
2.1. Search 5.2. Add phone
2.2. Copy fr. mobile phone 5.3–7. Added phones3
3 A maximum of 5 phones.
``
Bluetooth handsfree*
6. Phone settings…
10
275
Type designation................................................................................... 278
Dimensions and weights....................................................................... 280
Engine specifications............................................................................ 283
Engine oil............................................................................................... 284
Fluids and lubricants............................................................................. 286
Fuel....................................................................................................... 289
Wheel and tyres, dimensions and pressure ......................................... 290
Electrical system................................................................................... 292
Type approval....................................................................................... 294
Symbols in the display.......................................................................... 295
276
SPECIFICATIONS
11 Specifications
Type designation
11
278
11 Specifications
Type designation
279
11 Specifications
Dimensions
11
C Load length, floor, folded seat 1766 H Rear track 1544A A with 15" wheel
B with 16" and 17" wheels
D Load length, floor 989 1531B
F Height 1457
280
11 Specifications
Weights WARNING
Kerb weight includes the driver, the fuel tank
The car's driving characteristics change
90% full and all fluids. depending on how heavily it is loaded and
The weight of passengers and accessories, how the load is distributed.
and towball load (when a trailer is hitched, see
table) influences the payload and is not
11
included in the kerb weight.
Permitted maximum load = Gross vehicle
weight - Kerb weight.
NOTE
The documented kerb weight applies to
cars in the standard version - i.e. a car with-
out extra equipment or accessories. This
means that for every accessory added the
loading capacity of the car is reduced cor-
respondingly by the weight of the acces-
sory. For decal location, see page 278.
Examples of accessories that reduce load- Max. total weight
ing capacity are the Kinetic/Momentum/
Summum equipment levels, as well as other Max. train weight (car+trailer)
accessories such as Towbar, Load carriers,
Space box, Audio system, Auxiliary lamps, Max. front axle load
GPS, Fuel-driven heater, Safety grille, Car- Max. rear axle load
pets, Cargo cover, Power seats, etc.
Weighing the car is a certain way of ascer- Equipment level
taining the kerb weight of your own partic-
ular car. Max. load: See registration document.
Max. roof load: 75 kg.
``
281
11 Specifications
Engine Maximum weight, braked trailer (kg) Maximum towball load (kg)
1.6 1200 50
D2 1300 75
11
2.0F 1350 75
2.0 1350 75
others 1500 75
Engine Maximum weight, unbraked trailer (kg) Maximum towball load (kg)
1.6, 2.0 and 2.0F 650 50
others 700 50
282
11 Specifications
Engine specifications
Overview
Engine Engine Output Output Torque (Nm/ No. of Bore Stroke Swept Com-
code (kW/rpm) (hp/rpm) rpm) cylinders (mm) (mm) volume pression
(litres) ratio
1.6 B4164S3 74/6000 100/6000 150/4000 4 79 81.4 1,596 11.0:1
11
2.0F B4204S4 107/6000 145/6000 185/4500 4 87.5 83.1 1,999 10.8:1
283
11 Specifications
Engine oil
Adverse driving conditions Volvo recommends Castrol oil products. Viscosity chart
Adverse driving conditions can lead to abnor-
mally high oil temperature or oil consumption. IMPORTANT
Below are some examples of adverse driving In order to fulfil the requirements for the
conditions. engine's service intervals all engines are
Check the oil level more frequently for long filled with a specially adapted synthetic
11 engine oil at the factory. The choice of oil
journeys:
has been made very carefully with regard to
• towing a caravan or trailer service life, starting characteristics, fuel
consumption and environmental impact.
• in mountainous regions
An approved engine oil must be used in
• at high speeds
order that the recommended service inter-
• in temperatures colder than -30 °C or hot- vals can be applied. Only use a prescribed
ter than +40 °C grade of oil for both filling and oil change,
The above also apply to shorter driving dis- otherwise you will risk affecting service life,
starting characteristics, fuel consumption
tances at low temperatures. and environmental impact.
Choose a fully synthetic engine oil for adverse Volvo Car Corporation disclaims all war-
driving conditions. It provides extra protection ranty liability if engine oil of the prescribed
for the engine. grade and viscosity is not used.
284
11 Specifications
Engine oil
Engine variant Engine code Recommended oil grade Volume, incl. oil filter
(litres)
1.6 B4164S3 Oil grade: ACEA A5/B5 4.0
11
2.0F B4204S4 Viscosity: SAE 5W–30 4.3
D2 D4162T 3.8
D4 D5204T 5.9
A SAE 0W-30 applies for Europe, SAE 5W-30 applies for other markets
285
11 Specifications
Overview
IMPORTANT
The recommended transmission fluid must
be used to prevent damage to the gearbox.
Do not mix with any other transmission fluid.
11 If the transmission is topped up with a dif-
ferent fluid, contact a workshop nearby for
servicing. Volvo recommends that you con-
tact an authorised Volvo workshop.
Gearbox oil
Manual gearbox Volume (litres) Prescribed transmission fluid
IB5 2.1 BOT 130 M
B6 1.6
M66 1.9
286
11 Specifications
Fluids
Fluid System Volume Recommended oil grade
(litres)
Coolant 1.6 5.8 Coolant recommended by Volvo mixed with 50% waterA, see the packaging. The thermostat
starts opening at:
2.0 and 2.0F 6.5 11
petrol engine (1.6) 82 °C,
T5, automatic 7.5
petrol engines 90 °C,
gearbox
diesel engines 82 °C
D2 6.2
diesel engine (D2) 83 °C
D3 and D4 8.5
Power steer- Power steering 1.0 – 1.2 WSS M2C204-A or equivalent product with same specifications.
ing fluid
Washer fluid 4-cyl. Petrol/Die- 4.0 Use a washer antifreeze recommended by Volvo, mixed with water for temperatures below
sel freezing.
``
287
11 Specifications
11 Petrol: T5 approx. 62
Diesel: D2 approx. 52
Diesel: see page 148
Diesel: D3 and D4 approx. 60
A Water quality must fulfil the standard STD 1285.1.
B Refrigerant quantity varies depending on engine variant. Volvo recommends that you contact an authorised Volvo workshop for the correct information.
288
11 Specifications
Fuel
To bear in mind
Tips that the driver can use in order to reduce
consumption:
• Drive gently and avoid unnecessary accel-
eration as well as braking too hard.
• Drive with the correct air pressure in the
tyres and check this regularly - select ECO
tyre pressure for best results.
• Choice of tyres can affect fuel consump-
tion - seek advice on suitable tyres from a
dealer.
289
11 Specifications
290
11 Specifications
Variant Tyre size Speed Load, 1 - 3 persons Max. load Max. load
(km/h)
Front (kPa) A Rear Front (kPa) Rear (kPa) ECO pressureB
(kPa)
205/55 R16 0–160 230 220 250 250 250
D3
205/50 R17 11
D4 160+ 270 220 290 270 -
215/45 R18
291
11 Specifications
Electrical system
General The battery capacity is dependent upon the capacity as the original battery (see the label
The car has a voltage-regulated AC alternator. equipment level in the vehicle. If the starter on the battery).
The electrical system is single-pole and uses battery is replaced, therefore, you must ensure
the chassis and engine casing as a conductor. that you switch to a battery with the same
11
Battery
12 700 B 135 80
A Cars equipped with High Performance audio system.
B Cars equipped with diesel, keyless drive, Premium Sound audio system, fuel-driven heater or RTI.
Bulbs
Lighting Output (W) Type
Dipped beam, cars with halogen lamps 55 H7
Main beam, cars with Dual Xenon or ABL (Active Bending Lights) 55 H7
Front direction indicators, cars with Dual Xenon or halogen, rear direction indicators 21 PY21W
292
11 Specifications
Electrical system
Fog lamps 35 H8
Type approval
BR
TW
ETC093LPD0155
294
11 Specifications
``
Symbol Meaning Page Symbol Meaning Page Information symbols in the centre
console display
Low oil pres- 54, 56 Left direction 53
Symbol Meaning Page
sure indicators
Surround sound (only 248
Premium Sound)
G021216
11
Seatbelt 18, 56 Right direction 53
reminder indicators News 252
G021221
Alternator not 56 Other information symbols in the Programme types 252
charging
combined instrument panel
G021222
Symbol Meaning Page
Rain sensor* 69 Regional radio pro- 253
Fault in brake 56, 165
grammes
system
G021223
Cruise control* 71 Audio files 255
Main beam 53
Directory in CD disc 255
indicator
G021220
Phone* 269
11
Airbag, passenger 25
seat, deactivated
297
12 Alphabetical Index
298
12 Alphabetical Index
299
12 Alphabetical Index
300
12 Alphabetical Index
Electrical system...................................... 292 Error messages in BLIS........................... 172 Frequency update, automatic.................. 253
Emergency calls...................................... 260 Expectant mothers, seatbelt...................... 19 Front seats, heated.................................... 95
Emergency equipment External dimensions................................ 280 FSC, environmental labelling..................... 14
warning triangle.................................. 195 Extra mats................................................ 110 Fuel
Emergency puncture repair..................... 199 CO2 emissions.................................... 289
Emission control consumption....................................... 289
fault indicator........................................ 55 F fuel consumption, display..................... 66
fuel economy...................................... 194
Engine block heater................................. 156
Fan fuel filter.............................................. 148
fuel-driven........................................... 101 12
A/C........................................................ 94 level indicator........................................ 55
Engine compartment............................... 216 ECC...................................................... 97 parking heater..................................... 101
coolant................................................ 222 refuelling............................................. 146
Fast-wind................................................. 256
oil........................................................ 218
First aid equipment.................................. 196 Fuses....................................................... 234
power steering fluid............................ 223
box in the engine compartment.......... 235
Engine oil................................. 218, 219, 284 Flexifuel.................................................... 156
changing............................................. 234
adverse driving conditions.................. 284 adaptation........................................... 157
general................................................ 234
capacities........................................... 284 Floor mats................................................ 110 relay/fuse box in the passenger com-
filter..................................................... 218 Fluids, capacities..................................... 286 partment............................................. 238
oil grade.............................................. 284
Fluids and oils.................................. 218, 286
oil pressure........................................... 56
Fluids and oils, checks, engine compart-
Engine specifications............................... 283
ment......................................................... 218 G
Entry, keyless............................................. 85
Fluids and oils general............................. 218 Gearbox
Environmental labelling, FSC, owner's
Fog lamps manual................................................ 159
manual....................................................... 14
rear........................................................ 63 Gear selector assistance (GSI - Gear shift
EON - Enhanced Other Networks............ 254
Fog lamps, on/off...................................... 63 indicator).................................................. 159
Equalizer.................................................. 248
Fold down the rear seat backrest ........... 118
301
12 Alphabetical Index
302
12 Alphabetical Index
303
12 Alphabetical Index
304
12 Alphabetical Index
Power sunroof........................................... 82 Random, CD and audio files.................... 256 Remote control........................................ 126
RDS functions.......................................... 251 replacing the battery........................... 133
Power windows......................................... 76
blocking................................................ 77 resetting.............................................. 254 Remote control, HomeLink
passenger seat..................................... 77 Reading lamps, see Lighting................... 111 programmable ..................................... 87
rear seat................................................ 77 Rear seat ................................................. 118 Remote control key................................. 155
Programme type...................................... 253 battery replacement............................ 133
Rearview and door mirrors
detachable key blade......................... 127
PTY – Programme type........................... 252 automatic retracting/extending...... 80, 85
functions............................................. 126
Puncture, see Tyres......................... 195, 197 compass............................................... 78
door...................................................... 80 Remote control key system, type appro-
Putting calls on hold................................ 262 val............................................................ 294
electrically retractable........................... 80
interior................................................... 78 Resetting the door mirrors......................... 80
Recirculation Reverse gear inhibitor.............................. 159
A/C........................................................ 94
Rims
ECC...................................................... 98
cleaning.............................................. 206
305
12 Alphabetical Index
Roof load, max. weight ........................... 281 Side airbag SIPS........................................ 26 Steering wheel
Rustproofing............................................ 211 SIM card.................................................. 260 cruise control........................................ 71
keypad.................................... 71, 73, 261
SIPS bags.................................................. 26
steering wheel adjustment.................... 74
SMS......................................................... 265
S read..................................................... 265
Stone chips and scratches...................... 210
306
12 Alphabetical Index
T removing............................................. 183 U
specifications...................................... 180
Tailgate Towing eye.............................................. 175 Unlocking......................................... 131, 134
driving with open tailgate................... 145 settings................................................. 85
TP – Traffic information............................ 252
locking/unlocking........................ 126, 134 Upper mounting points, child seat............ 44
Traffic information.................................... 252
Tank volume............................................ 286 USB, connection...................................... 246
Trailer....................................................... 177
Technical data, engine............................. 283
cable................................................... 179
Temperature
actual temperature............................... 93
Trip computer............................................ 66
V 12
passenger compartment, electronic cli- Tuning Radio............................................ 250
mate control.......................................... 99 Type approval, remote control key sys- Ventilation.................................................. 93
passenger compartment, manual cli- tem........................................................... 294 Vibration damper..................................... 179
mate control.......................................... 96 Type designation..................................... 278 Volume
Testing the alarm system......................... 139 Tyres audio system...................................... 246
Timer direction of rotation............................ 193 auto volume control............................ 249
A/C........................................................ 95 driving characteristics......................... 190 media player....................................... 246
ECC...................................................... 98 general................................................ 190
Tools........................................................ 195 maintenance....................................... 190
307
12 Alphabetical Index
12 Weights
kerb weight......................................... 281
Wheels
changing............................................. 197
installation........................................... 198
removal............................................... 197
rims..................................................... 192
snow chains........................................ 192
spare wheel........................................ 195
Whiplash injury.......................................... 29
WHIPS
child seat/booster cushion................... 29
whiplash injury...................................... 29
Windscreen wipers.................................... 68
rain sensor............................................ 69
Winter tyres.............................................. 193
Wiper
rear window.......................................... 69
308
Kdakd8Vg8dgedgVi^dcIE&'*'.:c\a^h] Int.!6I&%)+!Eg^ciZY^cHlZYZc!<iZWdg\'%&%!8deng^\]i©'%%%"'%&%Kdakd8Vg8dgedgVi^dc