Professional Documents
Culture Documents
The user, through its own analysis and testing, is solely responsible for making the final selection of the system and components and assuring that all performance, endurance,
maintenance, safety and warning requirements of the application are met.OFFER The user OFanalyze
WARNING
must SALE all aspects of the application, follow applicable industry standards, and follow
the information concerning the product in the current product catalog and in any other materials provided from Parker or its subsidiaries or authorized distributors.
The items described in this document are hereby offered for sale by Parker-Hannifin Corporation,
The products described in this catalog can expose you to chemicals, including Lead, which is known its subsidiaries or its authorized
to the State distributor.
of California to causeThis offerand
cancer and birth
its acceptance
defects or
are governed
To the by the
extent that provisions
Parker stated in theordetailed "Offer of Sale" elsewhere in this document.
other reproductive harm.orFor
its subsidiaries
more informationauthorized distributors provide component
go to www.p65warnings.ca.gov. or system options based upon data or specifications provided by the user, the user is
responsible for determining that such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of the components or systems.
OFFER OF SALE
The items described in this document are hereby offered for sale by Parker-Hannifin Corporation, its subsidiaries or its authorized distributor. This offer and its acceptance
are governed by the provisions stated in the detailed "Offer of Sale" elsewhere in this document.
Contents
D, H, and V-Pak Series
Introduction........................................................................................................................ 2-3
Ordering Information.......................................................................................................... 4-9
Installation Information.................................................................................................. 10-14
Technical Information.......................................................................................................... 15-27
D-Paks 18.9 (5) 3.4 - 10.2 (0.9 - 2.7) 0.37 (0.5) - 2.24 (3) 207 (3000)
H-Paks 37.9 (10), 75.7 (20), 113.6 (30), 151.4 (40) 3.4 - 36.3 (0.9 - 10.4) 0.37 (0.5) - 14.9 (20) 207 (3000)
V-Paks 37.9 (10), 75.7 (20), 113.6 (30), 151.4 (40) 7.6 - 59.1 (2.0 - 15.6) 1.5 (2) - 14.9 (20) 207 (3000)
Standard Features
Standard
• VerticalFeatures
Design Benefits
• Submerged Pump
Vertical Design Benefits
• Saves Floor Space
Spare ReturnPump
• Submerged Ports QuieterFloor
• Saves Operation,
Space Elimination of Potential
• Precision Pump
Spare Return Mounting Adapters
Ports Leak Point
• Quieter Operation, Elimination of Potential
Suction Strainer
• Precision Pump Mounting Adapters • Longer Pump Life
Leak Point
Glycerine
• Suction Filled Pressure Gage with Shut Off
Strainer ProtectsPump
• Longer PumpLife
from Contamination
• Glycerine
Oil Level Gage
Filledwith Thermometer
Pressure Gage with Shut Off • Improved Diagnostics
Protects Pump from Contamination
Relief
• Oil Valve
Level Gage with Thermometer Helps to Maintain
• Improved Trouble-Free Performance
Diagnostics
• SAE Drainand
Breather Plug
Fill Cap • Easy To Fill
Protects Reservoir
Against System Shock
• SAE
Parker Connector
Drain Plug Technology • Easy
Prevents Leaks
To Fill Reservoir
•• Parker
Available with Digital
Connector Drives
Technology • Prevents Leaks
(See DCP Pak section of this catalog)
• Available with Digital Drives
Schematic
(See DCPSymbol
Pak section of this catalog)
(Hydraulic Schematic - Basic Unit)
Schematic Symbol
(Hydraulic Schematic - Basic
P Unit)
T P T
“O” “O”
OPTION X P T P A X OPTION X P T P A X
MANIFOLD
“O” MANIFOLD
“O”
OPTION X T
P B
A X
X OPTION X T
P B
A X
X
MANIFOLD MANIFOLD
T B X T B X
M SPARE
M SPARE
M RETURN M RETURN
SPARE “OMIT” SPARE
RETURN OPTION RETURN
COMP
“OMIT”
CONTROL
OPTION
SAE X SAE X
-12 -12 COMP
CONTROL
SAE X
D & H-PAK BASIC UNIT SAE X
V-PAK BASIC UNIT
-12 ——————————— -12 —————————
NO OPTIONS
D & H-PAKORBASIC
ACCESSORIES
UNIT NO OPTIONS OR ACCESSORIES
V-PAK BASIC UNIT
———————————
“O” OPTION MANIFOLD —————————
“OMIT” OPTION PUMP COMPENSATOR
NO OPTIONS OR ACCESSORIES NO OPTIONS OR ACCESSORIES
“O” OPTION MANIFOLD
“O” OPTION MANIFOLD “OMIT” OPTION PUMP COMPENSATOR
3 “O” OPTION MANIFOLD
Parker Hannifin Corporation
Parker Hannifin Corporation Hydraulic Pump Division
Maryville,
Parker Ohio USA
Hannifin Corporation
Hydraulic Pump and Power Systems Division 3
United States Hydraulic Pump Division
3 Maryville, Ohio USA
HY28-2661-CD/US Hydraulic Power Units
D-Paks Ordering Information D-Pak Series
D5 P
Reservoir Pressure Pump Flow D = Dual Rated* Motor Hp Manifold Directional Manapak Options
18.9 Liters Control W = No Motor** Control Control and
(5 Gal) Valve Valves* Accessories
J
24VDC) N.O. (Energize coil to close) Double AB
*Do not select a motor smaller than 2 Hp with these flow rates. Supply/Return
Porting Block/
Port or
Code Subplate Other
If No Motor Electric Motor Description HP Actuator Port
Code or Manifold Type
or Dual Rated @ RPM-Frame-Phase Size
U1 1/2 @ 1725-56C-1 Pressure and Return
P & T Ports Convertible to
O Port Block with Safety
T1 1 @ 1725-56C-1 SAE-12 Str. Thr'd S5 Option
Relief Valve
T3 1 @ 1725-56C-3 D03 Single Station
A & B Ports Spare P & T
W G 56C (no motor)** S3 Subplate with Safety
SAE-8 Str. Thr'd SAE-10 Ports
Relief Valve
D G 2 @ 1760 / 2 @ 1450-56C-3 DUAL RATED
D05 Single Station
D K 3 @ 1760 / 3 @ 1455-56C-3 DUAL RATED A & B Ports Spare P & T
S5 Subplate with Safety
SAE-10 Str. Thr'd SAE-12 Ports
W L 182TC/184TC (no motor)** Relief Valve
Double AB
Double AB
Double AB
Double AB
Double AB
Units less valves will be supplied with station cover plates installed.
From H-Pak
Options &
Accessories
Code Configuration
Omit End of Model Code
AC10 Drive configured per the
\
following selections
DCP Option Not Available on 1/2 and 1 Hp Units
OR Reduced
Flow
Reservoir Pressure Pump Control Pump Flow D = Dual Rated* Motor Hp Manifold
Control W = No Motor**
= Omit if not required Manifolds are mounted vertically. Bottom station is number 1.
P
Directional Manapak Options
Control Valve Control Valves• and
Accessories
Directional
NFPA Nominal Flow
Code Control Valve Description Circuit Symbol
Mounting Pad GPM (LPM)
Model Number
Double AB
Double AB
Double AB
Double AB
Units less valves wil be supplied with station cover plates installed.
NFPA
Manapak Control Valve Model Nominal Flow
Code Mounting Circuit Symbol
Valves Function Number GPM (LPM)
Pad
Flow
1 FM2DDKN D03 7 (26.5)
Control
Flow
2 FM3DDKN D05 12 (45.4)
Control
Pilot Operator
3 CPOM2DDN D03 7 (26.5)
Check
Pilot Operator
4 CPOM3DDN D05 12 (45.4)
Check
*Manapak valves mounted in order of callout.
First valve will be nearest DCV; last valve will be on manifold.
381 (15.00 )
19.1 (.75 )
343 (13.50 )
"B" 318 (12.50 ) T
B A
“O” & “S3” OPTION MANIFOLD
(P & T BLOCK & D03 SINGLE STATION)
BASIC UNIT
PRESSURE GAGE
WITH NEEDLE VALVE
SPARE RETURN PORT
1/2" NPTF
WITH DROP PIPE
“O” (“P” & “T” BLOCK)
OR “S3” (“D03” SUBPLATE)
“A” * SHOWN-SEE MANIFOLD OPTIONS
B A FILLER
BREATHER
OIL LEVEL
SIGHT GAGE
T
263.1
(10.36) TANK DRAIN
SAE-12 (PLUGGED)
38.1
(1.5)
B A
B A
33.3
“B” (1.31)
.56 DIA. MOUNTING
HOLES - 4 PLACES
T
ELECTRIC MOTOR
P
355.6
(14.00)
FOR V-PAKS
OIL LEVEL
SIGHT GAGE
38.1
T
(1.5)
P
409.5 3.1
(16.12) (.12)
“M5*” OPTION MANIFOLD
(MULTI-STATION D05 MANIFOLD)
SHOWN WITH OPTION “O” RETURN FILTER
Code KW(HP)-RPM-Frame-Phase
B A
B A
Dimensions
Dimensions
– Basic–H2,Basic and
3, 4,H2, 4, and
3,V2, 3, 4 V2, 3, 4 Filter Option
FilterReference
Option Reference
(20, 30, (20,
40 Gallon
30, 40 Tank)
Gallon Tank) SPARE RETURNSPARE
PORT RETURN PORT
3/4" NPTF 3/4" NPTF
Inch equivalents
Inch equivalents
for millimeter
for dimensions
millimeter dimensions
are shown are
in (**).
shown in (**). WITH DROP PIPE
WITH DROP PIPE
38.1 38.1
“B” (1.5) “B” (1.5)
.56 DIA. MOUNTING
.56 DIA. MOUNTING IN IN
HOLES - 4 PLACES
HOLES - 4 PLACES
SPARE RETURNSPARE
PORT RETURN PORT
3/4" NPTF WITH3/4" NPTF WITH
DROP PIPE DROP PIPE
431.8 431.8
(17.0) (17.0) ELECTRIC MOTOR
ELECTRIC MOTOR
T
508.0 508.0 PUMP PREFILL PUMP
PORT PREFILL PORT
P
(20.0) (20.0) FOR V-PAKS (8-15
FORGPM
V-PAKS
ONLY)
(8-15 GPM ONLY)
PUMP COMPENSATOR
PUMP COMPENSATOR
CONTROL CONTROL
22.9 22.9 FOR V-PAKS FOR V-PAKS
(.9) “O” (.9)
& “S5” OPTION
“O” & “S5”
MANIFOLD
OPTION MANIFOLD
(NOT INCLUDED(NOT
ON H-PAKS)
INCLUDED ON H-PAKS)
(P & T BLOCK(P&&D05
T BLOCK
SINGLE& D05
STATION)
SINGLE STATION)
BASIC UNIT BASIC UNIT
ROTATION ARROW
ROTATION ARROW
FILLER FILLER
BREATHER BREATHER
A-D03
B-D05
B-D03
A-D05
A-D03
B-D05
B-D03
A-D05
LIFT EYES - 2 PLACES
LIFT EYES - 2 PLACES
SPARE RETURNSPARE
PORT RETURN PORT
3/4" NPTF 3/4" NPTF
WITH DROP PIPE
WITH DROP PIPE
OIL LEVEL OIL LEVEL
SIGHT GAGE SIGHT GAGE
OUT OUT
38.1 38.1
(1.5) (1.5)
T
Motor Motor
Motor
Description
Motor DescriptionDimension Dimension
“M5*” OPTION
“M5*”
MANIFOLD
OPTION MANIFOLD
Code
Motor CodeMotorKW(HP)-RPM-Frame-Phase
Description
KW(HP)-RPM-Frame-Phase “A” * Dimension
“A”
“B”
* “B” (MULTI-STATION
(MULTI-STATION
D05 MANIFOLD)
D05 MANIFOLD)
Code KW(HP)-RPM-Frame-Phase
U1 .37(.5)U1 .37(.5) -1725-56C-1
-1725-56C-1 266.70 (10.50)266.70
“A”* (10.50)
19.05 19.05 (.75)
(.75) “B” SHOWN WITHSHOWN
OPTIONWITH
“N” RETURN
OPTION “N”
FILTER
RETURN FILTER
C1
U1 .56(.75) C1 .56(.75) -1725-56C-1
-1725-56C-1
.37(.5) -1725-56C-1 279.40
279.40 (11.00)
266.70 (11.00)
19.05
(10.50) (.75) 19.05 (.75)
19.05 (.75)
T1
C1 .75(1)T1
.56(.75) .75(1) -1725-56C-1
-1725-56C-1
-1725-56C-1 298.45
298.45 (11.75)
279.40 .75 (11.75)
(19.05)
(11.00) .75 (19.05)
19.05 (.75)
T3 .75(1)T3 .75(1) -1725-56C-3
-1725-56C-3 266.70 (10.50)266.70 (10.50)
19.05 (.75) 19.05 (.75)
T1 .75(1) -1725-56C-1 298.45 (11.75) .75 (19.05)
F 1.1(1.5)F-1725-56C-3
1.1(1.5) -1725-56C-3
273.05 (10.75)273.05 (10.75)
19.05 (.75) 19.05 (.75)
T3 .75(1) -1725-56C-3 266.70 (10.50) 19.05Reservoir
(.75)
G 1.5(2)G-1725-56C-3 1.5(2) -1725-56C-3
298.45 (11.75)298.45 (.75) 19.05 (.75) Reservoir
(11.75)
19.05 Reservoir Dimension
Reservoir Dimension
DG 2 (1.5)-1725 - 56C-3 DUAL RATED 359 (14.1) Code
19.05 (.75) Size
Code “C”
Size “C”
K 2.2(3)K-1725-56C-3 2.2(3) -1725-56C-3
320.55 (12.62)320.55 (12.62)
19.05 (.75) 19.05 (.75)
Reservoir
151.4 LitersReservoir
151.4
491.74 Dimension
Liters 491.74
DK 3 (2.2) - 1725-182TC DUAL RATED 435 (17.1) 19.05 (.75)
L 3.7(5)L-1725-184TC-3
3.7(5) -1725-184TC-3
365.25 (14.38)365.25
28.70(14.38)
(1.13) 28.70
H2 or(1.13)
V2 Code H2 or V2Code “C”
(20 Gal) (19.36)
(20 Gal) (19.36)
B A B A
ML 5 (3.75) M
5.6(7.5) 1725 - 5.6(7.5)
184TC - 3-1725-213TC-3
- -1725-213TC-3 435406.40
406.40 (16.00) 35.05
(17.1) (16.00)
28.7035.05
(1.38) (1.13) (1.38)
H2113.6
or V2 Liters
151.4 Liters 491.74
G G
113.6
599.95Liters 599.95
H3 or V3 H3 or V3 (19.36)
(1.38) (1.38) (30 Gal) (20 Gal)
B A B A
NM 7.5 (5.6)N
7.5(10) 1725 - 7.5(10)
213TC - -1725-215TC-3
--1725-215TC-3 458413.51
3 413.51 (16.28) 35.05
(18) (16.28)
35.0535.05
(1.38) (23.62)
(30 Gal) (23.62)
PN 10 (7.5) -P-1725-254TC-3
11.2(15) 1725 -11.2(15)
215TC - 3-1725-254TC-3 473447.80
447.80 (17.63) 85.09
(18.6) (17.63)
35.0585.09
(3.35) (1.38) (3.35)
H375.7
or V3 Liters
113.6 Liters
75.7
733.04 599.95733.04
Liters
H4 or V4 H4 or V4
S 14.9(20)S-1725-256TC-3
14.9(20) -1725-256TC-3
492.25 (19.3) 492.25 (3.35) 85.09 (3.35) (40 Gal) (30 Gal)
85.09(19.3) (40 Gal)(23.62)(28.86)
(28.86)
P 15 (11.2) - 1725 - 254TC - 3 522 (20.5) 85.09 (3.35)
* Reference dimension
* Reference
consult
dimension
factory consult
if criticalfactory
to application.
if critical to application. H4 or V4 75.7 Liters 733.04
S 20 (14.9) - 1725 - 256TC - 3 DUAL RATED 522 (20.5) 85.09 (3.35) (40 Gal) (28.86)
15 15 Parker Hannifin
Parker
Corporation
Hannifin Corporation
Parker Hannifin
Hydraulic Pump Corporation
Hydraulic
DivisionPump Division
Hydraulic Pump
Maryville, Ohio and
Maryville,
USA Power Systems Division
Ohio USA
12 United States
HY28-2661-CD/US Hydraulic Power Units
Technical Information
Catalog HY28-2661-CD/US Vertical Power Units D, H, and V-Pak Series
Technical Information VolumeD,
Series Control
H, V-Paks
Manifold Options
Inch equivalents for millimeter dimensions are shown in (**).
X
RETURN P T “A” RETURN P T “A”
PORT X P A X PORT PORT X P A PORT
SAE-10 SAE-8 SAE-10 SAE-8
T B
“B” T TB
“B” T
X PORT PORT
D03 SAE-8 D03 SAE-8
87.4 P P
COVER (3.44) 52.3 MNTG
PLATE SURFACE
(2.06) 31.8
(1.25)
44.2
PUMP (1.75) PUMP
SUPPLY SUPPLY
B A B A
85.9
(3.38) 47.8
(1.88)
22.0 44.5
(.87) (1.75)
O S3
T B X PORT T
B
44.5 PORT
D05 SAE-10 (1.75) D05 SAE-10
COVER MNTG
P
17.5 53.8
(.69) (2.12)
O S5
MANIFOLD OPTION
FOR SUPPLY & RETURN CONNECTIONS SUBPLATE OPTION
(37.9, 75.7, 113.6, 115.4 LIT FOR USE WITH D3W VALVE
(10, 20, 30, 40 GAL) RESERVOIR UNITS) (NFPA D05)
Manifold Options
Inch equivalents for millimeter dimensions are shown in (**).
RETURN
PORT
Option M33/M35 SAE-10
X
P T
A
3 AND 5 STATIONS)
"A"&"B"PORTS
B
SAE-8
T
A
G B
"G"
SAE-6 D03
MNTG
SURFACE
33.3
(1.31)
PUMP
SUPPLY
54.0
(2.12)
PER STATION
3 AND 5 B A
STATION
G
AVAIL. 54.0
4.25 B A (2.12)
22.1 1.06
(0.87)
44.5
(1.75)
RETURN
Option M53/M55 PORT
SAE-12
X
P T
A
3 AND 5 STATIONS
"A"&"B"PORTS
B
SAE-8
A
P
G B
"G"
SAE-6 D05
MNTG
SURFACE 31.8
(1.25)
PUMP
SUPPLY
82.6 (3.25)
PER STATION
3 AND 5 B A
STATION
AVAIL.
165.1 G 82.6
(6.50) (3.25)
B A
39.6
17.5 (1.56)
(0.69)
54.0
(2.12)
T T
INVERTED
INVERTED
INVERTED
INVERTED
UPRIGHT
UPRIGHT
UPRIGHT
UPRIGHT
P
B A
B A G
B A
Pressure Control
Pressure Control Option
Option "B"
"B"–Unloading Valve
– Unloading Valve
T T T T
INVERTED
INVERTED
INVERTED
INVERTED
INVERTED
INVERTED
UPRIGHT
UPRIGHT
UPRIGHT
UPRIGHT
UPRIGHT
UPRIGHT
P P
B A B A
B A B A G G
B A B A
T
INVERTED
INVERTED
UPRIGHT
UPRIGHT
B A
"D"PAK WITH
"H"PAK WITH "OMIT" MANIFOLD "H"PAK WITH
"OMIT","S3","S5","S6","M3*","M5*","M6*"
"OMIT","S5","S6","M5*","M6*" MANIFOLDS (CONNECTED TO SYSTEM RETURN ) MANIFOLDS
3.4-19.3 LPM (0.9-5.1 GPM) FLOW RATES ONLY 23.84-46.56 LPM (6.3-12.3 GPM) FLOW RATES ONLY
(PLUMBED DIRECTLY BACK TO TANK) (PLUMBED DIRECTLY BACK TO TANK)
19
18 Parker Hannifin
Parker Hannifin Corporation
Corporation
Parker Hannifin
Hydraulic
Hydraulic Corporation
Pump Division
Pump Division
Hydraulic
Maryville, Pump and Power Systems Division
Ohio USA
Maryville, Ohio USA
16 United States
HY28-2661-CD/US Hydraulic Power Units
Technical Information
Catalog HY28-2661-CD/US Vertical Power Units V-Pak Series
Technical Information VolumeV-Paks
Series Control
P T HIGH
SOL
P
P
SAE
SOLENOID IS LOW WATT
-6 WITH DIN. 43650 CONNECTOR
AND MANUAL OVERRIDE
HI LO
SOL SOL
HI
LO
“C” OPTION T
“D” OPTION T
BI-PRESSURE HIGH LOW BI-PRESSURE HIGH LOW
LOW SOL
REMOTE COMPENSATOR PSI PSI REMOTE COMPENSATOR PSI PSI
STANDBY
W/LOW PRESS. STANDBY
HIGH HIGH
SOL SOL
P P
HI LO HI LO
SOL SOL SOL SOL
HI HI
LO LO
“F” OPTION
PROVISION FOR
CUSTOMER SUPPLIED
REMOTE COMPENSATOR
SAE -6
37 FLARE
P T
P P
T
T
PUMP COMPENSATOR
PRESSURE (INLET) PORT
PUMP COMPENSATOR
TANK (RETURN) PORT
OPTION B RETURN LINE AIR/OIL HEAT EXCHANGER (B1 OR B2) OPTION L CHECK VALVE–RETURN LINE BYPASS
OPTION C WATER/OIL HEAT EXCHANGER OPTION N RETURN LINE FILTER
OPTION E SYSTEM COOLING/FILTER LOOP OPTION O RETURN LINE FILTER
OPTION H PRESSURE FILTER OPTION R COMBINATION TEMP/LEVEL SWITCH (R1 OR R2)
OPTION J WELD COUPLING FOR HEATER
OPTION K CHECK VALVE–PUMP OUTLET
SEE MANIFOLD
OPTIONS
SAE - 10
SAE - 6
SAE - 10
SAE - 6
SAE - 10
SEE
COMPENSATOR
OPTIONS
SAE - 12
CONNECTED TO RETURN
LINE WITH OPTION “B1” & “B2”
19.8
[0.78]
P
10.8
[0.43]
129.5
[5.1]
OPTION "B1" REF.
AIR/OIL
HEAT EXCHANGER
16.3
[0.64]
16.9
[0.67]
16.9
[0.67]
12.7
[0.50]
10.2 12.7
[0.40] [0.50]
10.2
[0.40]
SPARE RETURN PORT
3/4" NPTF
SPAREWITH DROP PIPE
RETURN PORT
3/4" NPTF
WITHOPTION "M", "N", "O" OR "V"
DROP PIPE
RETURN FILTER
OPTION "M", "N", "O" OR "V"
RETURN FILTER
T
T
TP
T
P
P
130
[5.1]
130
OPTION "B1" [5.1] OPTION "A"
AIR/OIL PUMP CASE HEAT EXCHANGER
HEAT EXCHANGER (USED ON "V" PAKS ONLY)
OPTION "B1" OPTION "A"
AIR/OIL PUMP CASE HEAT EXCHANGER
HEAT EXCHANGER (USED ON "V" PAKS ONLY)
26.5
89.7
[1.04] [3.53]
26.5
89.7
[1.04] [3.53]
DIM DIM
"A" "A"
REF OPTION "R1" OR" R2" REF
FLOAT/TEMP. SWITCH
DIM (1/2" ELEC. CONN.) DIM
"A" "A"
REF OPTION "R1" OR" R2" REF
A-D03 B-D03
FLOAT/TEMP.
OPTION "H" SWITCH A-D03 B-D03
B-D05 A-D05 (1/2" ELEC.
PRESSURE FILTERCONN.) B-D05 A-D05
A-D03 B-D03
OPTION "H" A-D03 B-D03
B-D05 A-D05
PRESSURE FILTER B-D05 A-D05
FLOAT 2"
BELOW
LOW LEVEL
FLOAT 2"
BELOW
LOW LEVEL
OPTION “E” WATER MODULATING VALVE WITH “C” HEAT EXCHANGER & 10 GALLON TANK
DRAIN (REF.)
OPTION “E” WATER MODULATING VALVE WITH “D” HEAT EXCHANGER and 10 GALLON TANK
BULB WELL
105.2
[4.14]
53.5
[2.11] 19.1
[0.75]
T
WITH DROP PIPE
P
P
OPTION "B2"
128.0
AIR/OIL [5.04]
HEAT EXCHANGER OPTION "A"
PUMP CASE HEAT EXCHANGER
(USED ON V-PAKS ONLY)
129.5 124.5
[5.10] [4.90] 89.7
[3.53]
DIM DIM
"A" "A"
REF OPTION "R1" OR "R2" REF
FLOAT/TEMP. SWITCH
(1/2"ELEC. CONN.)
OPTION "H"
PRESSURE FILTER
FLOAT 2"
BELOW
LOW LEVEL
q
38.0
[1.49]
Dimensions – H2,
Dimensions 3, 4,
– H2, 3,and V2,V2,
4, and 3, 43,(20, 30,30,
4 (20, 40 Gallon Tank)
40 Gallon Accessories
Tank) (continued)
Accessories (continued)
InchInch
equivalents for millimeter
equivalents dimensions
for millimeter are shown
dimensions in (**).
are shown Installation
in (**). information
Installation is forisreference
information only.only.
for reference Consult
Consult
factory or visit Parker's Econfigurator for detailed information.
factory or visit Parker's Econfigurator for detailed information.
SPARESPARE
RETURN PORT PORT SPARESPARE
RETURN PORT PORT
RETURN
RETURN 3/4" NPTF
3/4" NPTF
3/4"WITH
NPTFDROP
WITH DROP 3/4"WITH
NPTFDROP
WITH DROP
TUBE (REF.) TUBE (REF.)
TUBE (REF.)
TUBE (REF.)
24 24 Parker Hannifin
Parker Corporation
Hannifin Corporation
Hydraulic PumpPump
Hydraulic Division
Division
Maryville,
Parker Ohio USA
Hannifin
Maryville, Ohio Corporation
USA
21 21 Hydraulic Pump and Power Systems Division
24 United States
HY28-2661-CD/US
HY28-2661-CD/US Hydraulic
Hydraulic Power
Power Units
Catalog
TechniHY28-2661-CD/US
cal In formation Vertical Power Units Series
H and H, V-Packs
V-Pak Series
Technical Information VolumeH, Control
Technical Information Series V-Paks
OPTION “E” WATER MODULATING VALVE WITH “C” HEAT EXCHANGER & 20/30/40 GALLON TANK
(20 GALLON TANK SHOWN)
1.5" REF
DRAIN (REF.)
OPTION “E” WATER MODULATING VALVE WITH “D” HEAT EXCHANGER & 20/30/40 GALLON TANK
6.5" REF
4.62" REF
BULB WELL
DCP
DCPPAK
PakDIMENSIONS
Dimensions
UNITS WILL BE CONFIGURED PER CUSTOMER’S MODEL CODE.
UNITS ARE TESTED PER CONFIGURATION TO ENSURE PROPER OPERATION.
*DIMENSION SHOWN IS DEPTH OF THE AC10 AS MEASURED FROM THE MOTOR FEET. REF H PAK DIMENSIONS
EARLIER IN THE CATALOG FOR MORE INFORMATION.
**** Represents maximum operating pressure with pump/motor combination. This will be the maximum relief valve or compensator setting.
D****
D &
andHRepresents
Pak - Pump/Motor
H Pak maximum operatingCombinations
- Pump/Motor Maximum
pressure with pump/motor Operating
combination. When Pressure
used on power unit products,Bar (PSI)
the highest relief valve or
compensator setting will be 3000 PSI. Combinations Maximum Operating Pressure Bar (PSI)
Pump Code Motor KW (HP)
Motor KW (HP)
DPump
&Flow
HFlow
Pak
at
at- Pump/Motor
Code
.37 (.5) Combinations
.37 (.5) .60 (.75)
.60 (.75) .75 (1) Maximum
.75 (1) 1.1 (1.5)
1.1 (1.5) 1.5 (2) Operating
1.5 (2) 2.2 (3) 3.7 (5)Pressure
2.2 (3) 5.6Bar
(7.5) (PSI)
5.6 (7.5) 7.5
3.7 (5)
(10) 11.2 (15)
7.5 (10)
14.9 (20)
11.2 (15) 14.9 (20)
1725 RPM Max Operating Pressure (Theoretical)
1725
LPMRPM
Pump Code
(GPM) MaxMotor KW Pressure
Operating (HP) (Theoretical)
LPM3.4(GPM)
Flow(0.9)at .37 (.5) .60
55.8(810) (.75) 111.7(1620)
84.1(1220) .75 (1) 1.1 (1.5) 223.4(3240)
167.5(2430) 1.5 (2) 2.2 (3) 3.7 (5) 5.6 (7.5) 7.5 (10) 11.2 (15) 14.9 (20)
119.3(1730) 159.3(2310) 239.2(3470)
1725
3.4 RPM 55.8(810)
4.9 (1.3)
(0.9)
40.0(580) 60.0(870) 80.0(1160)
Max Operating
84.1(1220) 111.7(1620) 167.5(2430) Pressure (Theoretical)
223.4(3240)
6.8 (1.8) 29.6(430) 44.1(640) 59.3(860) 88.3(1280) 118.6(1720) 177.2(2570) 275.0(3988) 275.0(3988)
LPM (GPM)
4.98.7(1.3)
(2.3) 40.0(580)
22.8(330) 60.0(870)
34.5(500) 80.0(1160)
46.2(670) 119.3(1730)92.4(1340)
69.0(1000) 159.3(2310) 239.2(3470)
138.6(2010) 231.0(3350)
3.4 (0.9) 55.8(810) 84.1(1220) 111.7(1620) 167.5(2430) 223.4(3240)
10.2 (2.7) 20.0(290) 30.3(440) 40.0(580) 60.0(870) 80.7(1170) 120.7(1750) 201.3(2920)
6.8
4.9(1.8)
(1.3) 29.6(430)
40.0(580) 44.1(640)
60.0(870) 59.3(860)
80.0(1160) 88.3(1280)159.3(2310)
119.3(1730) 118.6(1720) 177.2(2570) 275.0(3988)
239.2(3470)
12.1 (3.2)
6.8 (1.8) 15.9(230)
29.6(430) 24.1(350)
44.1(640) 31.7(460)
59.3(860) 48.3(700) 118.6(1720)
88.3(1280) 64.1(930) 177.2(2570) 160.6(2330) 241.3(3500)
96.5(1400) 275.0(3988)
8.7 (2.3)
17.0 (4.5)
22.8(330)
11.0(160)
34.5(500)
17.2(250)
46.2(670)
22.8(330)
69.0(1000)
33.8(490)
92.4(1340) 138.6(2010)
45.5(660) 138.6(2010)
231.0(3350)
115.1(1670) 172.4(2500) 228.9(3320)
69.0(1000) 231.0(3350)
8.7 (2.3) 22.8(330) 34.5(500) 46.2(670) 69.0(1000) 92.4(1340)
10.2
19.3(2.7)
10.2 (5.1)
(2.7) 20.0(290)
10.3(150) 30.3(440)
20.0(290) 15.2(220)
30.3(440) 40.0(580)
20.7(300)
40.0(580) 60.0(870) 80.7(1170)
30.3(440)
60.0(870) 80.7(1170)
40.7(590) 120.7(1750)
61.4(890)
120.7(1750) 201.3(2920)
102.0(1480)
201.3(2920) 153.1(2220) 204.1(2960) 275.0(3988)
23.8 (6.3) 8.3(120) 12.4(180) 16.5(240) 24.8(360) 33.1(480) 49.6(720) 82.7(1200) 124.1(1800) 165.5(2400) 248.2(3600)
12.1 (3.2) 15.9(230) 24.1(350) 31.7(460) 48.3(700) 64.1(930) 96.5(1400) 160.6(2330) 241.3(3500)
30.7(3.6)
13.7 (8.1) 13.8(200) 9.7(140)
21.4(310) 12.4(180)
28.3(410) 18.6(270) 24.8(360)
42.7(620) 45.5(660)
57.2(830)37.2(540) 62.7(910)
85.5(1240) 93.8(1360)
142.7(2070) 125.5(1820) 187.5(2720) 251.0(3640)
214.4(3110)
17.0 (4.5) 11.0(160) 17.2(250) 22.8(330) 33.8(490) 69.0(1000) 115.1(1670) 172.4(2500) 228.9(3320)
35.6 (9.4) 8.3(120) 11.0(160) 16.5(240) 21.4(310) 32.4(470) 53.8(780) 81.4(1180) 108.2(1570) 162.0(2350) 215.8(3130)
17.0
19.3(4.5)
(5.1) 11.0(160)
10.3(150) 17.2(250)
15.2(220) 22.8(330)
20.7(300) 33.8(490)
30.3(440) 45.5(660)
40.7(590) 69.0(1000)
61.4(890) 115.1(1670)
102.0(1480) 172.4(2500)
153.1(2220) 275.0(3988)
204.1(2960)228.9(3320)
46.6 (12.3) 8.3(120) 11.7(170) 15.9(230) 24.1(350) 40.0(580) 60.0(870) 80.0(1160) 120.0(1740) 160.0(2320)
23.8 (6.3) 8.3(120) 12.4(180) 16.5(240) 24.8(360) 33.1(480) 49.6(720) 82.7(1200) 124.1(1800) 165.5(2400) 248.2(3600)
19.3 (5.1) 10.3(150) 15.2(220) 20.7(300) 30.3(440) 40.7(590) 61.4(890) 102.0(1480) 153.1(2220) 204.1(2960) 275.0(3988)
30.7 (8.1) 9.7(140) 12.4(180) 18.6(270) 24.8(360) 37.2(540) 62.7(910) 93.8(1360) 125.5(1820) 187.5(2720) 251.0(3640)
23.8
35.6(6.3)
(9.4) 8.3(120) 12.4(180)
8.3(120) 16.5(240)
11.0(160) 24.8(360) 21.4(310)
16.5(240) 33.1(480)32.4(470)
49.6(720) 82.7(1200)
53.8(780) 124.1(1800)
81.4(1180) 108.2(1570)165.5(2400)
162.0(2350) 248.2(3600)
215.8(3130)
46.6 (12.3) 8.3(120) 11.7(170) 15.9(230)
32.7 (8.6) 9.0(130) 11.7(170) 17.2(250) 23.4(340)24.1(350) 40.0(580)
35.2(510) 60.0(870)
59.3(860) 80.0(1160)
88.3(1280) 120.0(1740) 160.0(2320)
117.9(1710) 176.5(2560) 236.5(3430)
39.5 (10.4) 7.6(110) 9.7(140) 14.5(210) 19.3(280) 29.0(420) 49.0(710) 73.1(1060) 97.9(1420) 146.2(2120) 195.5(2835)
Motor KW (HP)
Pump LPM (GPM) @ 1725 RPM 1.5 (2) 2.2 (3) 3.7 (5) 5.6 (7.5) 7.5 (10) 11.2 (15) 14.9 (20)
V-Pak - Pump/Motor
PVP16
Combinations
7.6 (2.0)
Maximum Operating Pressure Bar
72.4(1050) 108.2(1570) 179.3(2600) 266.1(3860)
(PSI)
PVP16 9.5 (2.5) 64.1(930) 232.4(3370)
94.5(1370) 155.1(2250) Motor KW (HP)
PVP16
Pump 11.4@
LPM (GPM) (3.0)
1725 RPM 57.2(830)
1.5 (2) 84.8(1230)
2.2 (3) 137.9(2000)
3.7 (5) 206.8(3000)
5.6 (7.5) 7.5 (10) 11.2 (15) 14.9 (20)
PVP16 7.6 (2.0)
13.2 (3.5) 72.4(1050)
51.7(750) 108.2(1570) 124.1(1800) 266.1(3860)
75.8(1100) 179.3(2600) 184.8(2680) 246.1(3570)
PVP16 9.5 (2.5)
15.1 (4.0) 64.1(930)
46.9(680) 94.5(1370) 113.8(1650) 232.4(3370)
68.9(1000) 155.1(2250) 168.2(2440) 223.4(3240)
PVP16 11.4
17.0 (3.0)
(4.5) 57.2(830)
43.4(630) 84.8(1230)
63.4(920) 137.9(2000) 153.8(2230) 204.8(2970) 305.4(4430)
103.4(1500) 206.8(3000)
PVP16 13.2
18.9 (3.5)
(5.0) 51.7(750)
40.0(580) 75.8(1100)
58.6(850) 124.1(1800) 142.0(2060) 246.1(3570)
96.5(1400) 184.8(2680) 188.9(2740) 281.3(4080)
PVP16 15.1
20.8 (4.0)
(5.5) 46.9(680)
37.9(550) 68.9(1000)
55.2(800) 113.8(1650) 132.4(1920) 223.4(3240)
89.6(1300) 168.2(2440) 175.1(2540) 261.3(3790)
PVP16 17.0
22.7 (4.5)
(6.0) 43.4(630)
35.2(510) 63.4(920)
51.7(750) 103.4(1500)
83.4(1210) 153.8(2230) 163.4(2370) 305.4(4430)
123.4(1790) 204.8(2970) 244.1(3540)
PVP16 18.9
24.6 (5.0)
(6.5) 40.0(580)
33.1(480) 58.6(850)
48.3(700) 96.5(1400)
77.9(1130) 142.0(2060) 153.0(2220) 281.3(4080)
115.8(1680) 188.9(2740) 228.2(3310)
PVP16 20.8
26.5 (5.5)
(7.0) 37.9(550)
31.0(450) 55.2(800)
45.5(660) 89.6(1300)
73.8(1070) 132.4(1920)
108.9(1580) 144.8(2100) 261.3(3790)
175.1(2540) 215.1(3120)
PVP16
PVP33 22.7
30.3 (6.0)
(8.0) 35.2(510) 51.7(750) 83.4(1210)
66.2(960) 123.4(1790)
97.9(1420) 129.6(1880) 244.1(3540)
163.4(2370) 193.1(2800) 255.1(3700)
PVP16
PVP33 24.6
32.2 (6.5)
(8.5) 33.1(480) 48.3(700) 77.9(1130)
64.1(930) 115.8(1680)
93.1(1350) 123.4(1790) 228.2(3310)
153.0(2220) 182.7(2650) 242.7(3520)
PVP16
PVP33 26.5
34.1 (7.0)
(9.0) 31.0(450) 45.5(660) 73.8(1070)
60.7(880) 108.9(1580)
88.9(1290) 117.2(1700) 215.1(3120)
144.8(2100) 174.4(2530) 231.0(3350)
PVP33 30.3
36.0 (8.0)
(9.5) 66.2(960)
57.9(840) 97.9(1420)
84.8(1230) 129.6(1880) 166.2(2410) 255.1(3700)
112.4(1630) 193.1(2800) 220.6(3200)
PVP33 32.2 (10.0)
37.9 (8.5) 64.1(930)
55.2(800) 93.1(1350)
81.4(1180) 123.4(1790) 159.3(2310) 242.7(3520)
106.9(1550) 182.7(2650) 206.8(3000)
PVP33 34.1 (10.5)
39.7 (9.0) 60.7(880)
53.1(770) 88.9(1290)
77.9(1130) 117.2(1700) 152.4(2210) 231.0(3350)
102.7(1490) 174.4(2530) 202.7(2940)
PVP33 36.0 (11.0)
41.6 (9.5) 57.9(840)
51.0(740) 84.8(1230)
75.2(1090) 112.4(1630) 146.9(2130) 220.6(3200)
98.6(1430) 166.2(2410) 194.4(2820)
PVP33 37.9
43.5 (10.0)
(11.5) 55.2(800)
49.0(710) 81.4(1180)
72.4(1050) 106.9(1550)
95.1(1380) 159.3(2310)
141.3(2050) 206.8(3000)
186.8(2710)
PVP33 39.7
45.4 (10.5)
(12.0) 53.1(770)
47.6(690) 77.9(1130)
69.6(1010) 102.7(1490)
91.7(1330) 152.4(2210)
135.8(1970) 202.7(2940)
180.0(2610)
PVP33 41.6
47.3 (11.0)
(12.5) 51.0(740)
46.2(670) 75.2(1090)
66.9(970) 98.6(1430)
88.3(1280) 146.9(2130)
131.0(1900) 194.4(2820)
173.7(2520)
PVP33 43.5
49.2 (11.5)
(13.0) 49.0(710)
44.8(650) 72.4(1050)
64.8(940) 95.1(1380)
85.5(1240) 141.3(2050)
126.9(1840) 186.8(2710)
167.5(2430)
PVP33 45.4
51.1 (12.0)
(13.5) 47.6(690)
43.4(630) 69.6(1010)
62.7(910) 91.7(1330)
82.7(1200) 135.8(1970)
122.7(1780) 180.0(2610)
162.0(2350)
PVP33 47.3
53.0 (12.5)
(14.0) 46.2(670)
42.1(610) 66.9(970)
60.7(880) 88.3(1280)
80.0(1160) 131.0(1900)
118.6(1720) 173.7(2520)
157.2(2280)
PVP33 49.2
54.9 (13.0)
(14.5) 44.8(650)
40.7(590) 64.8(940)
59.3(860) 85.5(1240)
77.9(1130) 126.9(1840)
115.1(1670) 167.5(2430)
152.4(2210)
PVP33 51.1
56.8 (13.5)
(15.0) 43.4(630)
39.3(570) 62.7(910)
57.2(830) 82.7(1200)
75.2(1090) 122.7(1780)
111.7(1620) 162.0(2350)
147.5(2140)
PVP33 53.0 (14.0) 42.1(610) 60.7(880) 80.0(1160) 118.6(1720) 157.2(2280)
PVP33 54.9 (14.5) 40.7(590) 59.3(860) 77.9(1130) 115.1(1670) 152.4(2210)
PVP33 56.8 (15.0) 39.3(570) 57.2(830) 75.2(1090) 111.7(1620) 147.5(2140)
Efficiency regulations and motor technology are constantly changing. The following information is general in
nature and could be affected by future changes in the motor industry.
CE Stamp
Motors that meet the IE3 efficiency standard (as of this writing) will have a CE stamp. The 2Hp, 3Hp and
dual-rated motors offered on the power units in this catalog have the CE stamp. Motors larger than 3Hp that
are not dual rated may not have a CE stamp.
Horsepower Ratings
The 2Hp and 3Hp motors are capable of delivering their full power rating at 50Hz and 60Hz. This may or may not
be the case for larger motors. While most motors can deliver their full rated horsepower at both frequencies, they
may not maintain their IE3 efficiency rating at full power at 50Hz, which they must do in order to carry the CE
mark. For example, a CE stamped dual-rated motor may be name-plated 10Hp @ 60Hz/7.5Hp @ 50Hz. In most
cases this is not an issue because the pump will be flowing less oil at 1500 RPM (50Hz) than it is at 1800 RPM
(60Hz). Less flow requires less horsepower for the same pressure. It is something to be aware of in case the
full 10Hp is expected at 50Hz. If it is, you may need to specify a 15Hp dual-rated motor in order to get 10Hp at
50Hz. The model code pages show the exact power rating for each motor at both frequencies.
The motors do not have grounded motor shafts, so if the inverter output has high harmonic content or if the unit
is expected to run a long time at low speeds, it may be advisable to supply or request a motor with a grounded
shaft. This grounding prevents arcing across the shaft bearings which leads to pitting.
90 34.1 9 90 68.2 18
Efficiency - %
Overall Efficiency
Overall Efficiency
80 30.3 8 80 60.6 16
Flow
70 26.5 7 Flow 70 53.0 14
60 22.7 6 60 45.4 12
KW HP KW HP
Flow
Flow
w
15.1 4
w
11.9 16.0 30.3 8 lo 23.9 32.0
lo lF
ll F ul
Fu 22.7 6 atF 17.9 24.0
Power
11.4 3 8.9 12.0
r at Power w er
7.6 2 owe 6.0 8.0 15.1 4 t Po 11.9 16.0
utP pu
In
3.8 1
Inp 3.0 4.0 7.6 2 6.0 8.0
Power wer
Compensated Compensated Po
0 0 0 0 0 0 0 0
Bar 0 69 138 207 275 Bar 0 69 138 207 275
PSI 0 1000 2000 3000 4000 PSI 0 1000 2000 3000 4000
Pressure Pressure
NOTE: The efficiencies and data in the graph are good WHERE:
only for pumps running at 1800 RPM and stroked to Q = Actual Output Flow in GPM
maximum. To calculate approximate horsepower for the
other conditions, use the following formula: PSI = Pressure At Pump Outlet
[ ]
Q x (PSI) N CHp= Input Horsepower @ Full compensation
HP = + (CHp) x @ 1800 RPM (from graph read at
1714 1800
operating pressure)
Actual GPM is directly proportional to drive speed and
maximum volume setting. Flow loss, however, is a N = Drive Speed in RPM
function of pressure only.
6 12 15 30
400 1000
B C E
Input Torque (In.-Lb.)
D D
Horsepower HP
Horsepower HP
F 10 25
C A E 800
300
4 8 10 20
B D 600
E
6 200 15
A C
D 400
2 4 5 10
C 100
B B 200
2 5
A A
0 0 0 0 0 0
0 1000 2000 3000 0 1000 2000 3000
Pressure - PSI Pressure - PSI
MOTOR KW (HP) MOTOR KW (HP)
1.5(2) 2.2(3) 3.7(5) 5.6(7.5) 7.5(10) 11.2(15) 5.6(7.5) 7.5(10) 11.2(15) 14.9(20)
Compensator Setting Bar (PSI) Compensator Setting Bar (PSI)
PVP16 110.3 151.7 206.8 206.8 206.8 206.8 PVP33 151.7 186.2 206.8 206.8
FULL STROKE (1600) (2200) (3000) (3000) (3000) (3000) FULL STROKE (2200) (2700) (3000) (3000)
Pump Control Option “H” with PVP16 Pump Control Option “H” with PVP33
Horsepower Limiting Horsepower Limiting
Factory Compensator Settings Factory Compensator Settings
1.1(1.5)
By Cooler KW (HP)
B2
.75(1)
.60(.8)
.45(.6)
A
.37(.5)
.30(.4)
B1* B1
.22(.3)
Horsepower Removed
By Reservoir RESERVOIR SIZE LITERS (GALLONS) Heat removal is based on
18.9(5) 37.9(10) 75.7(20) 113.6(30) 151.4(40) static ambient air at 29.4oC
(85oF) and max. oil temperature
KW (HP) REMOVAL .15(.2) .28(.38) .43(.58) .51(.68) .60(.81)
of 57.2oC (135oF).
Sample Power Comparison When Used on a Transfer, Clamp, and Transfer Application.
Sample power comparison when used on a transfer, clamp and transfer application.
The blue line represents the power consumed using a single speed pump.
The blue line represents the power consumed using a single speed pump.
The orange line shows the power consumption using a Parker DCP in 2 speed mode.
The orange line shows the power consumption using a Parker DCP in 2 speed mode.
1.8
1.6
1.4
1.2
1
KWH
0.8
0.6
0.4
0.2
0
2‐spd KWHrs 1‐spd KWHrs Accum KWHrs
PARKER’S
DCP
PAK
is
available
in
5
factory
set
options.
The
software
and
settings
that
are
required
for
the
selected
option
will
be
downloaded
and
tested
before
the
unit
is
shipped.
The
5
options
are
described
in
the
following
section.
Once
the
unit
is
HY28-2661-CD/US Hydraulic Power Units
received
it
can
be
installed
and
used
without
any
programming
from
the
customer.
If
desired,
some
variables
can
be
adjusted
Safety &via
Technical
the
unit’s
kInformation
eypad,
or
additional
edits
can
be
performed
by
using
a
laptop
computer.
H-Pak Series
For
detailed
with DCP
information
regarding
the
drive
please
refer
to
the
drive’s
product
manual
HA502703U001,
available
at
parker.com
or
contact
Parker’s
SSD
Division.
Available Configurations:
WARNING: Branch circuit protection with a maximum rating of 5KA current limiting must be supplied
WARNING - USER RESPONSIBILITY
per local electrical codes.
R SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH,
D PROPERTY DAMAGE.
ormation from Parker-Hannifin Corporation, its subsidiaries and authorized distributors provide product or system options for further investigation
pertise.
alysis and testing, is solely responsible for making the final selection of the system and components and assuring that all performance, endurance,
ning requirements of the application are met. The user must analyze all aspects of the application, follow applicable industry standards, and follow
he product in the current product catalog and in any other materials provided from Parker or its subsidiaries or authorized distributors.
ts subsidiaries or authorized distributors provide component or system options based upon data or specifications provided by the user, the user is
hat such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of the components or systems.
OFFER OF SALE
document are hereby offered for sale by Parker-Hannifin Corporation, its subsidiaries or its authorized distributor. This offer and its acceptance
ns stated in the detailed "Offer of Sale" elsewhere in this document.
! !
*
*
The
setting
*The default switch default
when
switch
ordering
setting
wvoltage
hen
ordering
control voltage
(option control
(option
V) will V)
will
be
If
be 0-10VDC. 0-‐10VDC.
0-5VDC
If
is0-‐5VDC
required is
required
the customerthe
must
change the
switch
customer
settingsmust
for change
0-5VDC. the
switch
settings
for
0-‐5VDC.
If
Dinstall
If DI2 is not used, I2
is
not
a ujumper
sed
install
between a
jumper
DI1band etween
DI2.DI1
and
DI2.
Discrete Speed
Discrete
speed
cControl:
ontrol:
If
oIfption
option “D”
“D”
is selected
is
selected
the
uthe unit
nit
w ill
bwill be configured
e
configured
to operate
to
operate
at 8 different
at
8
different
speeds
bspeeds
ased
on
based
the
on the
combination
combination
of making 3 inputs
of
making
3
inputs
active.
active.
There
There
are
are
also
also
two
two
ddiscrete inputsthat
iscrete
inputs
that need
need
to
tobe
be wired
wired
by
tby
he
cthe customer
ustomer
to enable
to
enable
the
the drive.
drive.
DI1
DI1
and DI2
and
D I2
nneed tobe
eed
to
be“ON”
“ON” (held
(held
at
2at4VDC)
24VDC) to start
to
start
the
dthe drive.
rive.
If either
If
either
input
input
goes
lgoes low
ow
the
the
unit
unit
will
will
stop.
stop.
See
the
See the
wiring
wiring example below. The unit will be factory set to operate at the speeds shown in the diagram. These
example
below.
The
unit
will
be
factory
set
to
operate
at
the
speeds
shown
in
the
diagram.
These
speeds
can
be
changed
by
speeds can be
changed by the customer
the
customer
using
the
kusing
eypad
the or
ckeypad
omputer
or computer
interface
(ref
interface (refoperating
to
the
AC10
to the AC10 operating manual).
manual).
CAUTION: Disabling
CAUTION:
Disabling
the
the
drive
drive
DOES
DOES
NNOT remove
OT
remove
power
power
from
from
the
the motor.
motor.
High
High
voltage
voltage
can
bcan be present
e
present
atotor
at
the
m the lmotor leads
eads
even
evenwhen
whenthe
themmotor
otor
is
nisot
not running.
running.
To
To ensure
ensure
the
the motor
motor
is tsafe
is
safe
to m
o
wire,
wire,
ake
make sure
sure
the
the disconnect
disconnect
is
locked
is
in
locked
the
OFF
inposition,
the OFF
position, incoming power is removed and the AC10’s display and LEDs are off, indicating the capacitors
incoming
power
is
removed
and
the
AC10’s
display
and
LED’s
are
off,
indicating
the
capacitors
are
discharged.
are discharged.
If DI2
is not used, install a jumper between DI1 and DI2.
If DI2 is not used install a jumper between DI1 and DI2.
Factory
Factory settings settings
for option for
option
Q: Q When :
When
motormotor
current
current > >95%
95%
FLA,
FLA,
DDO1
O1
turns
turnson.
on.
See
See F310
F310 in
AinC10
AC10 manual.
manual.
When
motor
current
<
75%
FLA,
DO1
turns
off.
See
F311
in
AC10
manual.
WhenF310
motor is
acurrent n
absolute
< 75% number,
FLA,ie
DO1 19
amps.
turns off. See F311 in AC10 manual.
F311
F310 is an absolute number, e.g. 19 i s
a
p ercentage,
i e
1 5%.
D O1
amps.
turns
on
when
the
motor
current
exceeds
19
amps
and
turns
off
when
the
motor
F311 current
is a percentage, is
less
than
e.g. (19-‐19x15%)
15%. DO1 or
1turns
6.15
aon
mps.
when the motor current exceeds 19 amps and turns off when the motor
is less than (19-19x15%) or 16.15 amps.
current
These
values
can
be
changed
by
the
customer
using
the
keypad
or
computer
interface
(ref
to
the
AC10
operating
manual).
These values can be changed by the customer using the keypad or computer interface (ref to the AC10 operating manual).
NOTE:
If
your
application
requires
a
lot
of
force
during
pre-‐travel
or
consumes
flow
during
clamping,
the
system
may
hunt
as
NOTE:the
Ifmyour otor
capplication urrent
crosses
requires the
MIN
a lotand
ofMforce
AX
current
during levels.
Option
pre-travel orD
consumes
(speed
determined
flow during by
inputs,
clamping,not
current)
the system may
bmay
e
a
hunt
better
o ption
i n
as the motor current crosses the MIN and MAX current levels. Option D (speed determined by inputs, not current) may be a t hese
c ases.
better option in these cases.
CAUTION:
Disabling
the
drive
DOES
NOT
remove
power
from
the
motor.
High
voltage
can
be
present
at
the
motor
leads
even
when
the
motor
is
not
running.
To
ensure
the
motor
is
safe
to
wire,
make
sure
the
disconnect
is
locked
in
the
OFF
position,
CAUTION: Disabling the drive DOES NOT remove power from the motor. High voltage can be present at the motor leads
even incoming
when thepmotor ower
is
isremoved
and
the
not running. ToAensure
C10’s
display
the motor and
LED’s
is safe are
to
off,
wire, indicating
make tsure he
capacitors
are
discharged.
the disconnect is locked
in the OFF
position, incoming power is removed and the AC10’s display and LEDs are off, indicating the capacitors are discharged.
If DI2If
isDI2
not is
nused
ot
used
installinstall
a ajumper
jumper
between
between
DDI1
I1
aand
nd
DI2.
DI2.
OPTIONAL BY CUSTOMER
If
DI2
is
not
used
install
a
jumper
between
DI1
and
DI2.
If DI2
is not used, install a jumper between DI1 and DI2.
Operating Notes
• Jog the electric motor once and verify that the • It is recommended that every 4,000 operating hours
electric motor is rotating in the same direction as the or once a year, whichever occurs first, the filler/
arrow on the electric motor housing. If direction is breather cap and suction strainer should be replaced.
incorrect, reverse two of the three leads on a
3-phase electric motor.
Fluid Recommendations
• D and H-Pak power units are tested and relief Premium quality hydraulic oil with a viscosity range
valve is set at maximum pressure of the pump/ between 150-250 SSU (30-50 cst.) at 100°F (38°C).
motor combination. Normal operating viscosity range between 80-1000 SSU
• V-Pak power units are tested and pressure control (17-180 cst.). Maximum start-up viscosity is 4000 SSU
valves are factory preset. If adjustments are needed, (1000 cst.).
follow the procedure below: Begin adjusting relief NOTE: Consult Parker when exceeding 160°F (71°C)
valve and pump compensator control valve to operation. Oil should have maximum anti-wear
increase pressure gradually. (NOTE: Always set relief properties, rust, and oxidation treatment.
valve 250 PSI higher than pump compensator
pressure control valve or severe overheating will
occur.) Filtration
• If pump fails to prime, vent pump discharge to For maximum pump and system component life, the
atmosphere to establish fluid flow. system should be protected from contamination at a
level not to exceed 125 particles greater than 10 microns
• Reservoir temperature should not exceed 66°C (150°F). per milliliter of fluid. (SAE Class 4 / ISO 16/13.) Due to
System reliability and component service life will be the nature of variable displacement pumps, variations
reduced when system is operated at higher in pump inlet conditions, fluid acceleration losses,
temperature. system aeration, and duty cycle must be carefully
• Clean fluid = improved system reliability and longer considered before specifying suction line filtration.
component service life, change filter elements Contact your Parker representative for assistance.
whenever filter indicators indicate a dirty element NOTE: For additional information refer to latest edition
condition. of Bulletin No. HY13-2600-550-001
HY13-2600-550-xxx..
Dimensions*
Pump Mounting Adapter
G
A G A
DIA. D P B DIA. D P B
DIA. DIA. DIA. DIA.
DIA. DIA.
G
G
876631 SAE AA 56C 6.7 5.0 5.88 N/A 4.50 3.50 1.63 3/8-16 0.44 2.00 YES YES 1 3 lb.
876632 SAE AA 182TC/256TC 9.0 5.3 7.25 N/A 8.50 5.00 1.63 3/8-16 0.56 2.00 YES YES 1 4 lb.
876633 SAE A 56C 6.7 5.0 5.88 N/A 4.50 4.25 2.10 3/8-16 0.44 3.25 YES YES 1 4 lb.
876634 SAE A 182TC/256TC 9.0 5.3 7.25 N/A 8.50 5.00 2.10 3/8-16 0.56 3.25 YES YES 1 4 lb.
876635 SAE A 182TC/256TC 9.0 5.3 7.25 N/A 8.50 5.88 2.10 3/8-16 0.56 3.25 YES YES 1 5 lb.
875343 SAE B 182TC/256TC 11.4 9.0 7.25 10.25 8.50 5.75 2.88 1/2-13 0.53 4.00 YES NO 2 7 lb.
875344 SAE B 182TC/256TC 11.4 9.0 7.25 10.25 8.50 6.81 2.88 1/2-13 0.53 4.00 YES NO 2 8 lb.
876683 SAE B 182TC/256TC 9.0 8.8 7.25 N/A 8.50 6.38 2.88 1/2-13 0.53 4.00 NO YES 1 7 lb.
876684 SAE C 182TC/256TC 9.0 9.3 7.25 N/A 8.50 6.69 3.56 5/8-11 0.53 5.00 NO YES 1 20 lb.
NOTE: It is the responsibility of the user to check the listed dimensions to ensure suitability of mounting adapter with pump/coupling/motor combination.
Application Formulas
• 1 GPM at 1500 PSI = 1 HP (General Rule) • 1 HP = 42.4 BTU/Min.
• 1 Gallon = 231 Cubic Inches (3.7854 Liters) • 1 Gallon = 3.7854 Liters
• 1 Gallon Oil = 7.08 Lbs.
• 1 bar = 14.5 PSI
• 25.4mm = 1 Inch
GPM x PSI
HP =
1714 x Pump Efficiency
HP x 63025
Torque =
RPM
HP x 63025
RPM =
Torque
Motor Information
At 440V — 3-Phase Motor Draws 1.25 AMP/HP
At 220V — 3-Phase Motor Draws 2.5 AMP/HP
At 110V — Single Phase Motor Draws 10 AMP/HP
The items described in this document and other documents and descriptions provided by Parker Hannifin Corporation, Hydraulics Group, and its authorized distributors (“Seller”)
are hereby offered for sale at prices to be established by Seller. This offer and its acceptance by any customer (“Buyer”) shall be governed by all of the following Terms and
Conditions. Buyer’s order for any item described in its document, when communicated to Seller verbally, or in writing, shall constitute acceptance of this offer. All goods or work
described will be referred to as “Products”.
1. Terms and Conditions. Seller’s willingness to offer Products, or accept an order for 11. Buyer’s Obligation; Rights of Seller. To secure payment of all sums due or otherwise,
Products, to or from Buyer is expressly conditioned on Buyer’s assent to these Terms Seller shall retain a security interest in the goods delivered and this agreement shall be
and Conditions and to the terms and conditions found on-line at www.parker.com/ deemed a Security Agreement under the Uniform Commercial Code. Buyer authorizes
saleterms/. Seller objects to any contrary or additional term or condition of Buyer’s Seller as its attorney to execute and file on Buyer’s behalf all documents Seller deems
order or any other document issued by Buyer. necessary to perfect its security interest. Seller shall have a security interest in, and lien
2. Price Adjustments; Payments. Prices stated on the reverse side or preceding pages upon, any property of Buyer in Seller’s possession as security for the payment of any
of this document are valid for 30 days. After 30 days, Seller may change prices to reflect amounts owed to Seller by Buyer.
any increase in its costs resulting from state, federal or local legislation, price increases 12. Improper Use and Indemnity. Buyer shall indemnify, defend, and hold Seller
from its suppliers, or any change in the rate, charge, or classification of any carrier. The harmless from any claim, liability, damages, lawsuits, and costs (including attorney
prices stated on the reverse or preceding pages of this document do not include any fees), whether for personal injury, property damage, patent, trademark or copyright
sales, use, or other taxes unless so stated specifically. Unless otherwise specified by infringement or any other claim, brought by or incurred by Buyer, Buyer’s employees,
Seller, all prices are F.O.B. Seller’s facility, and payment is due 30 days from the date or any other person, arising out of: (a) improper selection, improper application or other
of invoice. After 30 days, Buyer shall pay interest on any unpaid invoices at the rate of misuse of Products purchased by Buyer from Seller; (b) any act or omission, negligent
1.5% per month or the maximum allowable rate under applicable law. or otherwise, of Buyer; (c) Seller’s use of patterns, plans, drawings, or specifications
3. Delivery Dates; Title and Risk; Shipment. All delivery dates are approximate and furnished by Buyer to manufacture Product; or (d) Buyer’s failure to comply with these
Seller shall not be responsible for any damages resulting from any delay. Regardless of terms and conditions. Seller shall not indemnify Buyer under any circumstance except
the manner of shipment, title to any products and risk of loss or damage shall pass to as otherwise provided.
Buyer upon tender to the carrier at Seller’s facility (i.e., when it’s on the truck, it’s yours). 13. Cancellations and Changes. Orders shall not be subject to cancellation or change
Unless otherwise stated, Seller may exercise its judgment in choosing the carrier and by Buyer for any reason, except with Seller’s written consent and upon terms that will
means of delivery. No deferment of shipment at Buyers’ request beyond the respective indemnify, defend and hold Seller harmless against all direct, incidental and conse-
dates indicated will be made except on terms that will indemnify, defend and hold Seller quential loss or damage. Seller may change product features, specifications, designs
harmless against all loss and additional expense. Buyer shall be responsible for any and availability with notice to Buyer.
additional shipping charges incurred by Seller due to Buyer’s changes in shipping, 14. Limitation on Assignment. Buyer may not assign its rights or obligations under this
product specifications or in accordance with Section 13, herein. agreement without the prior written consent of Seller.
4. Warranty. Seller warrants that the Products sold hereunder shall be free from defects 15. Entire Agreement. This agreement contains the entire agreement between the
in material or workmanship for a period of eighteen months from the date of delivery Buyer and Seller and constitutes the final, complete and exclusive expression of the
to Buyer. The prices charged for Seller’s products are based upon the exclusive terms of the agreement. All prior or contemporaneous written or oral agreements or
limited warranty stated above, and upon the following disclaimer: DISCLAIMER OF negotiations with respect to the subject matter are herein merged.
WARRANTY: THIS WARRANTY COMPRISES THE SOLE AND ENTIRE WARRANTY 16. Waiver and Severability. Failure to enforce any provision of this agreement will
PERTAINING TO PRODUCTS PROVIDED HEREUNDER. SELLER DISCLAIMS ALL not waive that provision nor will any such failure prejudice Seller’s right to enforce that
OTHER WARRANTIES, EXPRESS AND IMPLIED, INCLUDING MERCHANTABILITY provision in the future. Invalidation of any provision of this agreement by legislation or
AND FITNESS FOR A PARTICULAR PURPOSE. other rule of law shall not invalidate any other provision herein. The remaining provisions
5. Claims; Commencement of Actions. Buyer shall promptly inspect all Products upon of this agreement will remain in full force and effect.
delivery. No claims for shortages will be allowed unless reported to the Seller within 10 17. Termination. This agreement may be terminated by Seller for any reason and at
days of delivery. No other claims against Seller will be allowed unless asserted in writing any time by giving Buyer thirty (30) days written notice of termination. In addition, Seller
within 60 days after delivery or, in the case of an alleged breach of warranty, within 30 may by written notice immediately terminate this agreement for the following: (a) Buyer
days after the date within the warranty period on which the defect is or should have commits a breach of any provision of this agreement (b) the appointment of a trustee,
been discovered by Buyer. Any action based upon breach of this agreement or upon receiver or custodian for all or any part of Buyer’s property (c) the filing of a petition
any other claim arising out of this sale (other than an action by Seller for any amount for relief in bankruptcy of the other Party on its own behalf, or by a third party (d) an
due to Seller from Buyer) must be commenced within thirteen months from the date of assignment for the benefit of creditors, or (e) the dissolution or liquidation of the Buyer.
tender of delivery by Seller or, for a cause of action based upon an alleged breach of 18. Governing Law. This agreement and the sale and delivery of all Products here-
warranty, within thirteen months from the date within the warranty period on which the under shall be deemed to have taken place in and shall be governed and construed
defect is or should have been discovered by Buyer. in accordance with the laws of the State of Ohio, as applicable to contracts executed
6. LIMITATION OF LIABILITY. UPON NOTIFICATION, SELLER WILL, AT ITS OPTION, and wholly performed therein and without regard to conflicts of laws principles. Buyer
REPAIR OR REPLACE A DEFECTIVE PRODUCT, OR REFUND THE PURCHASE PRICE. irrevocably agrees and consents to the exclusive jurisdiction and venue of the courts
IN NO EVENT SHALL SELLER BE LIABLE TO BUYER FOR ANY SPECIAL, INDIRECT, of Cuyahoga County, Ohio with respect to any dispute, controversy or claim arising out
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF, OR AS THE RESULT of or relating to this agreement. Disputes between the parties shall not be settled by
OF, THE SALE, DELIVERY, NON-DELIVERY, SERVICING, USE OR LOSS OF USE OF arbitration unless, after a dispute has arisen, both parties expressly agree in writing to
THE PRODUCTS OR ANY PART THEREOF, OR FOR ANY CHARGES OR EXPENSES arbitrate the dispute.
OF ANY NATURE INCURRED WITHOUT SELLER’S WRITTEN CONSENT, EVEN IF 19. Indemnity for Infringement of Intellectual Property Rights. Seller shall have no
SELLER HAS BEEN NEGLIGENT, WHETHER IN CONTRACT, TORT OR OTHER LEGAL liability for infringement of any patents, trademarks, copyrights, trade dress, trade
THEORY. IN NO EVENT SHALL SELLER’S LIABILITY UNDER ANY CLAIM MADE BY secrets or similar rights except as provided in this Section. Seller will defend and
BUYER EXCEED THE PURCHASE PRICE OF THE PRODUCTS. indemnify Buyer against allegations of infringement of U.S. patents, U.S. trademarks,
7. Contingencies. Seller shall not be liable for any default or delay in performance if copyrights, trade dress and trade secrets (“Intellectual Property Rights”). Seller will
caused by circumstances beyond the reasonable control of Seller. defend at its expense and will pay the cost of any settlement or damages awarded in
8. User Responsibility. The user, through its own analysis and testing, is solely an action brought against Buyer based on an allegation that a Product sold pursuant to
responsible for making the final selection of the system and Product and assuring that this Agreement infringes the Intellectual Property Rights of a third party. Seller’s obliga-
all performance, endurance, maintenance, safety and warning requirements of the tion to defend and indemnify Buyer is contingent on Buyer notifying Seller within ten (10)
application are met. The user must analyze all aspects of the application and follow days after Buyer becomes aware of such allegations of infringement, and Seller having
applicable industry standards and Product information. If Seller provides Product or sole control over the defense of any allegations or actions including all negotiations
system options, the user is responsible for determining that such data and specifica- for settlement or compromise. If a Product is subject to a claim that it infringes the
tions are suitable and sufficient for all applications and reasonably foreseeable uses of Intellectual Property Rights of a third party, Seller may, at its sole expense and option,
the Products or systems. procure for Buyer the right to continue using the Product, replace or modify the Product
9. Loss to Buyer’s Property. Any designs, tools, patterns, materials, drawings, confi- so as to make it noninfringing, or offer to accept return of the Product and return the
dential information or equipment furnished by Buyer or any other items which become purchase price less a reasonable allowance for depreciation. Notwithstanding the
Buyer’s property, may be considered obsolete and may be destroyed by Seller after foregoing, Seller shall have no liability for claims of infringement based on information
two consecutive years have elapsed without Buyer placing an order for the items which provided by Buyer, or directed to Products delivered hereunder for which the designs
are manufactured using such property. Seller shall not be responsible for any loss or are specified in whole or part by Buyer, or infringements resulting from the modification,
damage to such property while it is in Seller’s possession or control. combination or use in a system of any Product sold hereunder. The foregoing provisions
10. Special Tooling. A tooling charge may be imposed for any special tooling, including of this Section shall constitute Seller’s sole and exclusive liability and Buyer’s sole and
without limitation, dies, fixtures, molds and patterns, acquired to manufacture Products. exclusive remedy for infringement of Intellectual Property Rights.
Such special tooling shall be and remain Seller’s property notwithstanding payment of 20. Taxes. Unless otherwise indicated, all prices and charges are exclusive of excise,
any charges by Buyer. In no event will Buyer acquire any interest in apparatus belonging sales, use, property, occupational or like taxes which may be imposed by any taxing
to Seller which is utilized in the manufacture of the Products, even if such apparatus authority upon the manufacture, sale or delivery of Products.
has been specially converted or adapted for such manufacture and notwithstanding 21. Equal Opportunity Clause. For the performance of government contracts and
any charges paid by Buyer. Unless otherwise agreed, Seller shall have the right to alter, where dollar value of the Products exceed $10,000, the equal employment opportunity
discard or otherwise dispose of any special tooling or other property in its sole discre- clauses in Executive Order 11246, VEVRAA, and 41 C.F.R. §§ 60-1.4(a), 60-741.5(a), and
tion at any time. 60-250.4, are hereby incorporated.