Professional Documents
Culture Documents
RECEIVER INSTALLATION:
IMPORTANT:
WHEN INSTALLING CEILING FAN REMOTE CONTROL WITH ANY EXISTING
WALL MANUAL FAN CONTROLS, THEY MUST BE REPLACED WITH A 2 POLE
ON/OFF SWITCH.
(Note: Disconnect the remote control during maintenance and cleaning by turning off the switch)
2. Connect mains input cables on the Remote Control Receiver, marked “AC POWER INPUT L” (Brown) and
“AC POWER INPUT N” (Blue) to the mains Active and Neutral connections. NOTE: EARTH CABLE
(GREEN) MUST BE WIRED DIRECTLY TO THE BODY OF THE CEILING FAN (refer to the instructions
supplied with your ceiling fan).
3. Connect wires from Remote Control Receiver marked “TO FAN WIRES L” (Brown) and “TO FAN WIRES
N” to the appropriate Active and Neutral input wires on the ceiling fan.
4. Connect light output from Remote Control Receiver marked “TO LIGHT/LIVE” (Black) the light ACTIVE
cable located on the ceiling fan.
NOTE: IF LIGHT OUTPUT FROM CEILING FAN REMOTE CONTROL IS NOT REQUIRED, OUTPUT CABLE
MUST BE TERMINATED VIA AN END CAP SCREW TERMINAL AND SUFFICIENTLY INSULATED.
5. Set the pairing code switch (marked DIP SWITCH) to the same code on both receiver and transmitter (See
“Paring Code Switches” section).
6. Insert the receiver into the hanging bracket. The fan canopy can then be raised to conceal both the receiver
and bracket. NOTE: Some fans may not provide suitable room for installation of the Remote Control
Receiver into the bracket/canopy assembly. In this case, receiver may be installed into the roof adjacent to
the ceiling fan location and in accordance with current wiring regulations.
FUNCTIONS OF TRANSMITTER:
LIGHT : ON/OFF- Press and release immediately to turn on or off the light. TRANSMITTER
FAN : Press to toggle the fan to High, Medium or Low speed, or to turn
off the fan.
DELAY OFF: when pressed, light will automatically turn off after 3 minutes.
When pressed, and when light is off, the light will turn on and
then turn off after 3 minutes
LIGHT TIMER: To activate, press this key, then use △ or ▽ keys to select
the desired time from 0.5 ~ 24 hours, light will turn off
automatically after that time.
FAN TIMER: To activate, press this key, then use △ or ▽ keys to select the
desired time from 0.5 ~ 24 hours. Fan will turn off
automatically after that time.
FAN AUTO : Sets the fan control to manual or automatic mode. The default
setting is manual mode.
TEMP. : When remote is in “FAN AUTO” mode, use △ or ▽ keys to
select the desired room temperature. The fan will
automatically very speeds depending upon the variance in
temperature between desired temperature and actual temperature.
- Variance 0℃~1℃, fan will turn on at low speed automatically.
- Variance 2℃~3℃, fan will turn on at medium speed automatically.
- Variance ≧4℃, fan will turn on at high speed automatically.
℃/℉ : Change between ℃ or ℉ by using a pen, or other small object to push
button located on rear of unit as shown (RIGHT).
Note : when Battery Low” symbol is shown on the LCD,
batteries should be replaced.
Temperature Unit
button
TROUBLE SHOOTING:
Warning: The power must be switched OFF prior to commencing troubleshooting procedures.
.
interfering with remote operation. with ON/OFF switch for remote
1 Fan is not operating Power to the fan has been switched - Switch isolation switch ON, to power the
or not operating correctly OFF at the isolation switch. remote receiver unit.
Remote Control Receiver wiring is - Verify wiring connections according to label
incorrect. and wiring diagram.
Transmitter and receiver Paring (DIP) - Set transmitter and receiver to same switch
switches do not match. setting.
The remote control is out of range of - Move remote control closer to the receiver
the receiver.
Other devices operating on similar - Change pairing code switches on both
2. Fan operates only at frequency receiver and remote.
close range
Battery is flat. - Replace battery with same type (9V).
3. Fan is operating RF interference or interference from - Change paring (DIP) switch settings to a
intermittently, or turning similar ceiling fans in neighbouring different code. Each pair of transmitter and
on without remote buildings. receiver must have unique DIP switch code.
- Replace with all new batteries. Do not mix up
Battery is flat
the old and new battery.
SPECIFICATION:
Receiver: 220-240V~ 50Hz, For fan motor: Max 100W (Min 5W); For fan lights: Max 300W (Tungsten
filament) or MAX 120W (CFL), Non dimming function.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Any claim under this warranty must be made within 2 years of the date of purchase of
the product. To make a claim under the warranty; at your own expense take the
product (with proof of purchase – receipt or similar) to the store where you purchased
the product or contact Brilliant Lighting at the address below.