Professional Documents
Culture Documents
User Guide
Revision 2.8
Contents
1. Download and install the tracker driver .................................................................................... 4
2. Connect the tracker to the computer .................................................................................... 4
2.1 TLW1 series ................................................................................................................................ 4
2.2 TLD1 series ................................................................................................................................. 4
2.3 TLP1 series .................................................................................................................................. 5
3. Configure the tracker.................................................................................................................... 5
3.1 Run the program ...................................................................................................................... 5
3.2 Choose a com port then click open ................................................................................... 6
3.3 Status............................................................................................................................................ 6
3.4 Network ....................................................................................................................................... 7
3.4.1 RAN Setting ....................................................................................................................... 7
3.4.2 Protocol .............................................................................................................................. 7
3.4.3 Online-config Server ...................................................................................................... 8
3.4.4 Primary Server .................................................................................................................. 8
3.4.5 Secondary Server............................................................................................................. 8
3.4.6 Data Acquisition............................................................................................................... 8
3.4.7 Heartbeat ........................................................................................................................... 8
3.4.8 Protocol Messages .......................................................................................................... 8
3.4.9 Pull current network configuration from device ................................................... 8
3.5 Advance....................................................................................................................................... 8
3.5.1 LEDs always on ................................................................................................................. 9
3.5.2 Towing alarm .................................................................................................................... 9
3.5.3 Sleep mode ....................................................................................................................... 9
3.5.4 Bluetooth............................................................................................................................ 9
3.5.5 Vibration ............................................................................................................................. 9
3.5.6 Jammer Alarm .................................................................................................................. 9
3.5.7 Driving Behavior via GNSS ........................................................................................... 9
3.5.8 Driving Behavior via Accelerometer .......................................................................... 9
3.5.9 Pull current advance configuration from device ................................................... 9
3.6 OBDII .......................................................................................................................................... 10
The USB serial ports section only shows the necessary com ports in default. If customer
want to see show all ports, please check “All ports”.
The program will recognize the tracker model name and enable corresponding page
buttons (Status, Network, Advance, OBDII, I/O, Alerts, Console). However, the Status,
Network and Console will be always enabled once the com port is successful opened.
3.3 Status
This page shows the read only information from device. The information may vary based on
different models. If customer wants to update the status information:
(1) If you are at this page, please click one more time on the Status button.
(2) If you are at another page, please click the status button to shift back to Status
page, then one more click on the Status button to get the latest information.
3.4.2 Protocol
Set the device protocol, TCP/UDP/MQTT(available in next version soon)
(1) MQTT
MQTT will use a new data server setting. When customer select MQTT,
new ip and port have to be set. Then the tracker will report to the MQTT
server.
3.4.7 Heartbeat
Keep alive packet sending interval
3.5 Advance
3.5.4 Bluetooth
Enable/disable the Bluetooth of the device. The device Bluetooth name also
can be changed here.
3.5.5 Vibration
Configure the vibration alarm
Note:
Please use INSTALLED command to calibrate the tracker accelerometer. The
calibration instructions can be found in the tracker command list.
3.6.5 Others
Only when the tracker is connected to a vehicle with ignition on, the vehicle
dashboard information will be shown.
3.7 I/O
3.8 Alerts
This page is only for TLP1 series products. The alerts will be enabled by checking it. Customer
can adjust the detail alert settings by click the side button.
If the setting doesn’t show in the configuration page (Network, Advance, OBDII, I/O, Alerts),
customer can use command to configure device in the console. Any command (supported by
tracker) can be sent in the console.
(1) Connect the first device to computer, then open the program
(4) After the program says the file is imported, click either of below button
(6) Click “Save to Device”. Then the program will start to write.
(7) When the program shows below, please power on another device then connect
it to the computer
4. Known issue
When the program stuck or crash, please close the program then open it again. Then
disconnect and re-connect the device again as well. We’ll keep optimizing the program.