Professional Documents
Culture Documents
PRINCIPLE OF OPERATION
For information on the operation of the system, refer to relevant section 204-05 -
Vehicle Dynamic Suspension of the workshop manual.
1. Confirm which, if any, warning lights and/or messages were displayed on the
instrument cluster. For a list of messages, Refer to the relevant section of the
workshop manual.
Visual inspection
MECHANICAL ELECTRICAL
1. Use the approved diagnostic system or a scan tool to retrieve any diagnostic
trouble codes (DTCs) before moving onto the symptom chart or DTC index.
Make sure that all DTCs are cleared following rectification.
SYMPTOM CHART
Vehicle does Suspension Two chimes Water ingress Visually inspect the
not sit level fault repeated to wiring wiring harness and
regularly harness or connectors for water
Red connectors ingress. Visually inspect
indicator the system for air
permanently Air leak(s) leakage and refer to the
illuminated Calibration guided diagnostic routine
corrupt on the approved
diagnostic system. Check
cross-link the system calibration
valve fault using the approved
diagnostic system. For
Height sensor front and rear cross link
fault valve tests refer to the
Reservoir guided diagnostic routine
valve stuck on the approved
open diagnostic system. Check
for height sensor DTCs
Exhaust valve and refer to the DTC
stuck closed index. For reservoir and
exhaust valve tests refer
Corner valves to the guided diagnostic
stuck open routine on the approved
Air suspension diagnostic system. Check
control module for corner valve DTCs
failure and refer to the DTC
index. Refer to the
warranty policy and
procedures manual if a
module is suspect.
Vehicle sits Suspension Two chimes, Water ingress Visually inspect the
too low fault amber to wiring wiring harness and
indicator harness or connectors for water
Hill permanently connectors ingress. Visually inspect
descent illuminated the system for air
control Air leak(s) leakage. For air
(HDC) One chime compressor temperature
fault, Air suspension
DSC amber compressor sensor, inlet air filter,
system not exhaust valve and air
available indicator temperature
permanently sensor fault compressor tests refer to
Dynamic illuminated the guided diagnostic
stability Inlet air filter routine on the approved
control ABS blockage diagnostic system. For
(DSC) indicator /restriction Air suspension control
permanently module lost
illuminated Air suspension communication with ABS
compressor module, refer to the lost
fault communication codes
Exhaust valve statement at the end of
stuck/sticking this table. Check for ABS
DTCs, Refer to the
Air suspension relevant section of the
control module workshop manual. Refer
lost to the warranty policy
communication and procedures manual if
with ABS a module is suspect.
module
ABS fault.
Air suspension
control module
failure
Vehicle sits Suspension Two chimes, Reservoir For reservoir valve and
too high fault amber valve stuck exhaust valve tests refer
indicator open to the guided diagnostic
permanently routine on the approved
illuminated Exhaust valve diagnostic system. Check
stuck closed for corner valve DTCs
Corner valves and refer to the DTC
stuck open index. Refer to the
warranty policy and
Air suspension procedures manual if a
control module module is suspect.
failure
Damage or
blockage in air
harness
DTC INDEX
NOTES:
Generic scan tools may not read the codes listed, or may read only 5-digit
codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit
code listed to identify the fault (the last 2 digits give extra information read
by the manufacturer-approved diagnostic system).
Intermittent faults may cause DTCs to be logged, however some DTCs may
be cleared during an ignition off, ignition on cycle. Carry out a road test (if
safe to do so), check the functionality of the system and retrieve any DTCs
before turning the ignition off.
B1A8455 Car Data does not Configure the car configuration file (CCF)
Configuration match that using the approved diagnostic system. Clear
Data expected for VIN the DTC and test for normal operation.
range/Air
suspension
incorrectly
configured
Servotronic
steering valve
circuit(s) high
resistance or
short circuit to
ground
Servotronic
steering valve
fault
Servotronic
steering valve
supply circuit
short circuit to
ground
Servotronic
steering valve
supply circuit
short circuit to
power
Servotronic
steering valve
fault
C112F72 Air Spring Valve Repeated or Refer to the approved diagnostic system for
frequent level corner valve checks.
activity in the
down direction
Corner valve
stuck open
C113066 Air Spring Air Repeated or Visually inspect the system for air leakage.
Supply frequent level Refer to the guided diagnostic routine for
activity in the up this code on the approved diagnostic system.
direction
Exhaust valve
stuck open
C11307A Air Spring Sir Unable to lift Visually inspect the system for an excessive
Supply vehicle air leak. Check the height sensor linkage(s)
for damage/restrictions. Visually inspect the
Detached air pipe air harness for evidence of melting, crushing,
Loose or burst air kinking or collapsing. Refer to the guided
pipe diagnostic routine for this code on the
approved diagnostic system.
Excessive air
spring leak
Height sensor
stuck
Height sensor
failure
Blockage in air
harness
C113192 Air Spring Air Unable to Visually inspect the system for air leakage.
Supply pressurize gallery Check the reservoir valve block pipes for
correct routing and installation.
Insufficient
pressure from
compressor
Reservoir valve
block pipes
incorrectly
installed (unions
reversed)
Pressure sensor
fault
C1A001C Control Module A momentary low Check the battery charge, condition and
voltage event circuit. Refer to the guided diagnostic routine
occurred for this code on the approved diagnostic
system.
Low battery
voltage
One or more
control valve
supplies
intermittent short
circuit to ground
C1A001D Control Module Isolation switch Refer to the guided diagnostic routine for
current monitor this code on the approved diagnostic system.
Refer to the warranty policy and procedures
One or more manual if a module is suspect.
valve supplies
short circuit to
ground
Air suspension
control module
failure
C1A0049 Control Module Water ingress to Visually inspect the wiring harness and
valve wiring connectors for water ingress. Refer to the
harness or guided diagnostic routine for this code on the
connector(s) approved diagnostic system. Refer to the
warranty policy and procedures manual if a
Valve supply module is suspect.
circuit(s) short
circuit to power
Air suspension
control module
internal electrical
failure
C1A0053 Control Module This is not a Carry out Air suspension deflation exit
fault, the system routine using the approved diagnostic
has been system or the routine listed at the end of this
deflated using section.
the diagnostic
routine
C1A0054 Control Module Air suspension If the problem is found during pre-delivery
control module inspection, check that the air suspension
not calibrated control module (RLM) is NOT in
manufacturing mode, calibration mode or
Air suspension tight tolerance mode using the approved
control module diagnostic system. Configure the RLM to
has been set into customer mode if necessary (tight tolerance
manufacturing, mode and manufacturing mode can be set
calibration or /cleared by starting then ending the
tight tolerance suspension geometry set process from IDS
mode menu. Refer to the relevant Technical
Service Bulletin). Clear the DTC and test for
normal operation. Only if the DTC re-occurs,
should the system be calibrated using the
approved diagnostic system. Clear the DTC
and test for normal operation.
C1A0119 LED Switch pack LED Refer to the guided diagnostic routine for
circuit, short this code on the approved diagnostic system.
circuit to power
One or more
LEDs short circuit
to each other
C1A031C Left Front Left-hand front Visually inspect the wiring harness and
Height Sensor height sensor connectors for water ingress. For height
signal voltage out sensor linkage, mounting and circuit tests
of range refer to the guided diagnostic routine on the
approved diagnostic system. Check the
Water ingress to height sensor bracket condition and security.
wiring harness or Check the height sensor for correct
connectors installation and torque of fixings. If any
Height sensor height sensor fixings are slackened or found
linkage to be loose, or a height sensor has been
disconnected changed, the vehicle ride height must be re-
calibrated. Calibrate the system using the
Height sensor approved diagnostic system. Refer to the
linkage damaged warranty policy and procedures manual if a
/bent module is suspect.
Height sensor
disconnected
Height sensor
linkage toggled
(now operating in
reverse direction)
Height sensor
bracket damaged
/bent
Height sensor
incorrectly
installed
Height sensor
installed on
wrong side of
vehicle
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Incorrect height
calibration
Air suspension
control module
failure
C1A0326 Left Front Left-hand front Visually inspect the wiring harness and
Height Sensor height sensor connectors for water ingress. Refer to the
signal voltage guided diagnostic routine for this code on the
stuck whilst approved diagnostic system. Refer to the
vehicle is driven warranty policy and procedures manual if a
module is suspect.
Water ingress to
wiring harness or
connectors
Height sensor
linkage
disconnected
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Air suspension
control module
failure
C1A0329 Left Front Left-hand front Visually inspect the wiring harness and
Height Sensor height sensor connectors for water ingress. Refer to the
signal invalid guided diagnostic routine for this code on the
approved diagnostic system. Check the
Water ingress to height sensor bracket condition and security.
wiring harness or Check the height sensor for correct
connectors installation and torque of fixings. If any
Height sensor height sensor fixings are slackened or found
linkage damaged to be loose, or a height sensor has been
/bent changed, the vehicle ride height must be re-
calibrated. Calibrate the system using the
Height sensor approved diagnostic system.
bracket damaged
/bent
Height sensor
incorrectly
installed
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Incorrect height
calibration
process
C1A0392 Left Front Left-hand front Check that the vehicle is free of obstructions.
Height Sensor height sensor Check the height sensor for correct
height changing installation and torque of fixings. If any
slower than height sensor fixings are slackened or found
expected to be loose, or a height sensor has been
changed, the vehicle ride height must be re-
Suspension calibrated. Calibrate the system using the
prevented from approved diagnostic system. Refer to the
moving guided diagnostic routine for this code on the
Height sensor approved diagnostic system. Check for an air
incorrectly spring leak. Check the air harness for
installed evidence of melting, crushing, kinking or
collapsing. Check the front and rear valve
Air spring leak block pipes for correct routing and
installation. Check the reservoir valve block
Air harness leak pipes for correct routing and installation.
Blocked Refer to the approved diagnostic system for
/damaged air corner, reservoir and exhaust valve checks.
harness Check the corner valve for leaks.
Blocked
/damaged gallery
pipe
Corner valve
stuck closed
Front or rear
valve block pipes
incorrectly
installed (unions
reversed)
Reservoir valve
block pipes
incorrectly
installed (unions
reversed)
Reservoir valve
stuck open
Exhaust valve
stuck closed
Pressure sensor
fault
Height sensor
failure
C1A041C Right Front Right-hand front Visually inspect the wiring harness and
Height Sensor height sensor connectors for water ingress. Refer to the
signal voltage out guided diagnostic routine for this code on the
of range approved diagnostic system. Check the
height sensor bracket condition and security.
Water ingress to Check the height sensor for correct
wiring harness or installation and torque of fixings. If any
connectors height sensor fixings are slackened or found
Height sensor to be loose, or a height sensor has been
linkage changed, the vehicle ride height must be re-
disconnected calibrated. Calibrate the system using the
approved diagnostic system. Refer to the
Height sensor warranty policy and procedures manual if a
linkage damaged module is suspect.
/bent
Height sensor
disconnected
Height sensor
linkage toggled
(now operating in
reverse direction)
Height sensor
bracket damaged
/bent
Height sensor
incorrectly
installed
Height sensor
installed on
wrong side of
vehicle
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Incorrect height
calibration
Air suspension
control module
failure
C1A0426 Right Front Right-hand front Visually inspect the wiring harness and
Height Sensor height sensor connectors for water ingress. Refer to the
signal voltage guided diagnostic routine for this code on the
stuck whilst approved diagnostic system. Refer to the
vehicle is driven warranty policy and procedures manual if a
module is suspect.
Water ingress to
wiring harness or
connectors
Height sensor
linkage
disconnected
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Air suspension
control module
failure
C1A0429 Right Front Right-hand front Visually inspect the wiring harness and
Height Sensor height sensor connectors for water ingress. Refer to the
signal invalid: guided diagnostic routine for this code on the
approved diagnostic system. Check the
Water ingress to height sensor bracket condition and security.
wiring harness or Check the height sensor for correct
connectors installation and torque of fixings. If any
Height sensor height sensor fixings are slackened or found
linkage damaged to be loose, or a height sensor has been
/bent changed, the vehicle ride height must be re-
calibrated. Calibrate the system using the
Height sensor approved diagnostic system.
bracket damaged
/bent
Height sensor
incorrectly
installed
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Incorrect height
calibration
process
C1A0492 Right Front Right-hand front Check that the vehicle is free of obstructions.
Height Sensor height sensor Check the height sensor for correct
height changing installation and torque of fixings. If any
slower than height sensor fixings are slackened or found
expected to be loose, or a height sensor has been
changed, the vehicle ride height must be re-
Suspension calibrated. Calibrate the system using the
prevented from approved diagnostic system. Refer to the
moving guided diagnostic routine for this code on the
Height sensor approved diagnostic system. Check for an air
incorrectly spring leak. Check the air harness for
installed evidence of melting, crushing, kinking or
collapsing. Check the front and rear valve
Air spring leak block pipes for correct routing and
installation. Check the reservoir valve block
Air harness leak pipes for correct routing and installation.
Blocked Refer to the approved diagnostic system for
/damaged air corner, reservoir and exhaust valve checks.
harness Check the corner valve for leaks.
Blocked
/damaged gallery
pipe
Corner valve
stuck closed
Front or rear
valve block pipes
incorrectly
installed (unions
reversed)
Reservoir valve
block pipes
incorrectly
installed (unions
reversed)
Reservoir valve
stuck open
Exhaust valve
stuck closed
Pressure sensor
fault
Height sensor
failure
C1A051C Left Rear Left-hand rear Visually inspect the wiring harness and
Height Sensor height sensor connectors for water ingress. Refer to the
signal voltage out guided diagnostic routine for this code on the
of range approved diagnostic system. Check the
height sensor bracket condition and security.
Water ingress to Check the height sensor for correct
wiring harness or installation and torque of fixings. If any
connectors height sensor fixings are slackened or found
Height sensor to be loose, or a height sensor has been
linkage changed, the vehicle ride height must be re-
disconnected calibrated. Calibrate the system using the
approved diagnostic system. Refer to the
Height sensor warranty policy and procedures manual if a
linkage damaged module is suspect.
/bent
Height sensor
disconnected
Height sensor
linkage toggled
(now operating in
reverse direction)
Height sensor
bracket damaged
/bent
Height sensor
incorrectly
installed
Height sensor
installed on
wrong side of
vehicle
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Incorrect height
calibration
Air suspension
control module
failure
C1A0526 Left Rear Left-hand rear Visually inspect the wiring harness and
Height Sensor height sensor connectors for water ingress. Refer to the
signal voltage guided diagnostic routine for this code on the
stuck whilst approved diagnostic system. Refer to the
vehicle is driven warranty policy and procedures manual if a
module is suspect.
Water ingress to
wiring harness or
connectors
Height sensor
linkage
disconnected
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Air suspension
control module
failure
C1A0529 Left Rear Left-hand rear Visually inspect the wiring harness and
Height Sensor height sensor connectors for water ingress. Refer to the
signal invalid guided diagnostic routine for this code on the
approved diagnostic system. Check the
Water ingress to height sensor bracket condition and security.
wiring harness or Check the height sensor for correct
connectors installation and torque of fixings. If any
Height sensor height sensor fixings are slackened or found
linkage damaged to be loose, or a height sensor has been
/bent changed, the vehicle ride height must be re-
calibrated. Calibrate the system using the
Height sensor approved diagnostic system.
bracket damaged
/bent
Height sensor
incorrectly
installed
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Incorrect height
calibration
process
C1A0592 Left Rear Left-hand rear Check that the vehicle is free of obstructions.
Height Sensor height sensor Check the height sensor for correct
height changing installation and torque of fixings. If any
slower than height sensor fixings are slackened or found
expected to be loose, or a height sensor has been
changed, the vehicle ride height must be re-
Suspension calibrated. Calibrate the system using the
prevented from approved diagnostic system. Refer to the
moving guided diagnostic routine for this code on the
Height sensor approved diagnostic system. Check for an air
incorrectly spring leak. Check the air harness for
installed evidence of melting, crushing, kinking or
collapsing. Check the front and rear valve
Air spring leak block pipes for correct routing and
installation. Check the reservoir valve block
Air harness leak pipes for correct routing and installation.
Blocked Refer to the approved diagnostic system for
/damaged air corner, reservoir and exhaust valve checks.
harness Check the corner valve for leaks.
Blocked
/damaged gallery
pipe
Corner valve
stuck closed
Front or rear
valve block pipes
incorrectly
installed (unions
reversed)
Reservoir valve
block pipes
incorrectly
installed (unions
reversed)
Reservoir valve
stuck open
Exhaust valve
stuck closed
Pressure sensor
fault
Height sensor
failure
C1A061C Right Rear Right-hand rear Visually inspect the wiring harness and
Height Sensor height sensor connectors for water ingress. Refer to the
signal voltage out guided diagnostic routine for this code on the
of range approved diagnostic system. Check the
height sensor bracket condition and security.
Water ingress to Check the height sensor for correct
wiring harness or installation and torque of fixings. If any
connectors height sensor fixings are slackened or found
Height sensor to be loose, or a height sensor has been
linkage changed, the vehicle ride height must be re-
disconnected calibrated. Calibrate the system using the
approved diagnostic system. Refer to the
Height sensor warranty policy and procedures manual if a
linkage damaged module is suspect.
/bent
Height sensor
disconnected
Height sensor
linkage toggled
(now operating in
reverse direction)
Height sensor
bracket damaged
/bent
Height sensor
incorrectly
installed
Height sensor
installed on
wrong side of
vehicle
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Incorrect height
calibration
Air suspension
control module
failure
C1A0626 Right Rear Right-hand rear Visually inspect the wiring harness and
Height Sensor height sensor connectors for water ingress. Refer to the
signal voltage guided diagnostic routine for this code on the
stuck whilst approved diagnostic system. Refer to the
vehicle is driven warranty policy and procedures manual if a
module is suspect.
Water ingress to
wiring harness or
connectors
Height sensor
linkage
disconnected
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Air suspension
control module
failure
C1A0629 Right Rear Right-hand rear Visually inspect the wiring harness and
Height Sensor height sensor connectors for water ingress. Refer to the
signal invalid guided diagnostic routine for this code on the
approved diagnostic system. Check the
Water ingress to height sensor bracket condition and security.
wiring harness or Check the height sensor for correct
connectors installation and torque of fixings. If any
Height sensor height sensor fixings are slackened or found
linkage damaged to be loose, or a height sensor has been
/bent changed, the vehicle ride height must be re-
calibrated. Calibrate the system using the
Height sensor approved diagnostic system.
bracket damaged
/bent
Height sensor
incorrectly
installed
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Incorrect height
calibration
process
C1A0692 Right Rear Right-hand rear Check that the vehicle is free of obstructions.
Height Sensor height sensor Check the height sensor for correct
height changing installation and torque of fixings. If any
slower than height sensor fixings are slackened or found
expected to be loose, or a height sensor has been
changed, the vehicle ride height must be re-
Suspension calibrated. Calibrate the system using the
prevented from approved diagnostic system. Refer to the
moving guided diagnostic routine for this code on the
Height sensor approved diagnostic system. Check for an air
incorrectly spring leak. Check the air harness for
installed evidence of melting, crushing, kinking or
collapsing. Check the front and rear valve
Air spring leak block pipes for correct routing and
installation. Check the reservoir valve block
Air harness leak pipes for correct routing and installation.
Blocked Refer to the approved diagnostic system for
/damaged air corner, reservoir and exhaust valve checks.
harness Check the corner valve for leaks.
Blocked
/damaged gallery
pipe
Corner valve
stuck closed
Front or rear
valve block pipes
incorrectly
installed (unions
reversed)
Reservoir valve
block pipes
incorrectly
installed (unions
reversed)
Reservoir valve
stuck open
Exhaust valve
stuck closed
Pressure sensor
fault
Height sensor
failure
C1A0762 Cross Cross articulation Follow the process detailed in the relevant
Articulation too large whilst special service message (SSM). Check the
vehicle is driven condition and security of the height sensor
bracket(s). Check the height sensor for
Water ingress to correct fitment and fixings torque. If any
wiring harness or height sensor fixings are slackened or found
connectors to be loose, or a height sensor has been
Height sensor changed, the vehicle ride height must be re-
linkage damaged calibrated. Calibrate the system using the
/bent approved diagnostic system.
Height sensor
linkage loose
/disconnected
Height sensor
bracket damaged
/bent
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
removed and
reinstalled
without being
recalibrated
New height
sensor installed
without
calibration
Incorrect height
calibration
Height sensor
failure
C1A081C Pressure Pressure sensor Refer to the guided diagnostic routine for
Sensor Supply supply voltage this code on the approved diagnostic system.
out of range Refer to the warranty policy and procedures
manual if a module is suspect.
Pressure sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Pressure sensor
failure
Air suspension
control module
failure
C1A091C Pressure Pressure sensor Refer to the guided diagnostic routine for
Sensor Signal signal voltage out this code on the approved diagnostic system.
of range Refer to the warranty policy and procedures
manual if a module is suspect.
Pressure sensor
disconnected
Pressure sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Pressure sensor
failure
Air suspension
control module
failure
C1A1064 Pressure Reservoir and air Check the reservoir and air spring pipes for
Fluctuates spring pipes correct routing and installation. Refer to the
When System incorrectly guided diagnostic routine for this code on the
Inactive installed to front approved diagnostic system. Refer to the
or rear valve warranty policy and procedures manual if a
block (unions module is suspect.
reversed)
Corner valve
stuck open
Pressure sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Pressure sensor
failure
Air suspension
control module
failure
C1A1164 Pressure Reservoir and air Check the reservoir and air spring pipes for
Fluctuates spring pipes correct routing and installation. For corner
When System incorrectly valve, reservoir valve, pressure sensor and
Inactive installed to front circuit tests refer to the guided diagnostic
or rear valve routine for this code on the approved
block (unions diagnostic system.
reversed)
Corner valve
internal leak
Reservoir valve
internal leak
Pressure sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Pressure sensor
failure
C1A1364 Pressure Does Exhaust valve Refer to the guided diagnostic routine for
Not Decrease stuck closed this code on the approved diagnostic system.
When Venting Check the Air suspension exhaust pipe and
Gallery Exhaust valve silencer for blockage/restriction. Check the
does not hold reservoir valve block pipes for correct routing
minimum and installation.
retention pressure
Gallery pipe
blocked/damaged
Pressure sensor
fault
Air suspension
exhaust silencer
blocked/restricted
Air suspension
exhaust pipe
blocked/damaged
Reservoir valve
block pipes
incorrectly
installed (unions
reversed)
C1A1864 Pressure Reservoir valve Refer to the guided diagnostic routine for
Increase Too stuck closed this code on the approved diagnostic system.
Rapid When
Filling Reservoir Reservoir pipe
blocked/damaged
Reservoir port
blocked/restricted
Pressure sensor
fault
C1A2064 Pressure Compressor fault Refer to the guided diagnostic routine for
Increase Too this code on the approved diagnostic system.
Slow When Reservoir pipe air Check the Air suspension intake pipe and
Filling Reservoir leak silencer for blockage/restriction.
Reservoir air leak
Intake filter
blocked/restricted
Intake pipe
blocked/restricted
Air suspension
intake silencer
blocked/restricted
Corner valve
stuck open
Pressure sensor
fault
Air compressor
cylinder head
temperature
sensor detached
from cylinder
head
Air compressor
cylinder head
temperature
sensor fault
Air compressor
fault
Air compressor
cylinder head
temperature
sensor
disconnected
Air compressor
cylinder head
temperature
sensor fault
Air compressor
disconnected
Air compressor
ground circuit
high resistance
Air compressor
fault
Air suspension
control module
failure
Air compressor
harness wiring
short circuit to
power
Air compressor
relay fault
Air suspension
control module
failure
Air compressor
harness wiring
short circuit to
ground or high
resistance
Air compressor
relay failure
Air suspension
control module
failure
C1A2729 Compressor Compressor relay DTC C1A2712 will be set first. Refer to the
Circuit control voltage guided diagnostic routine for this code on the
signal invalid approved diagnostic system. Refer to the
warranty policy and procedures manual if a
Air compressor module is suspect.
harness wiring
short circuit to
power
Air compressor
relay fault
Air suspension
control module
failure
C1A2864 Wrong Number Wrong number of Check/renew fuse as necessary. Refer to the
of LEDs LEDs illuminated electircal guides. Refer to the electrical
Illuminated on switch pack guides and check the switch pack and LED
wiring ciruits. Renew/repir as necessary.
Air suspension Refer to the warranty policy and procedures
control module manual if a module is suspect.
supply
(BATTERY) fuse
in battery
junction box
(BJB) failed
Switch pack
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
One or more
LEDs short circuit
to each other
Switch pack
failure
Air suspension
control module
failure
C1A2992 Switch Ride height Refer to the guided diagnostic routine for
Activation Too change switch this code on the approved diagnostic system.
Long activation too Refer to the warranty policy and procedures
long manual if a module is suspect.
Switch pressed
for more than
255 seconds
Switch pack
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Switch pack
failure
Air suspension
control module
failure
Switch pack
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Switch pack
failure
Air suspension
control module
failure
C1A3101 Left Front Left-hand front Refer to the guided diagnostic routine for
Corner Valve corner valve, this code on the approved diagnostic system.
general electrical Refer to the warranty policy and procedures
failure manual if a module is suspect.
Left-hand front
corner valve
failure
Air suspension
control module
failure
C1A3201 Right Front Right-hand front Refer to the guided diagnostic routine for
Corner Valve corner valve, this code on the approved diagnostic system.
general electrical Refer to the warranty policy and procedures
failure manual if a module is suspect.
Front valve block
disconnected
Right-hand front
corner valve
failure
Air suspension
control module
failure
C1A3301 Left Rear Left-hand rear Refer to the guided diagnostic routine for
Corner Valve corner valve, this code on the approved diagnostic system.
general electrical Refer to the warranty policy and procedures
failure manual if a module is suspect.
Left-hand rear
corner valve
failure
Air suspension
control module
failure
C1A3401 Right Rear Right-hand rear Refer to the guided diagnostic routine for
Corner Valve corner valve, this code on the approved diagnostic system.
general electrical Refer to the warranty policy and procedures
failure manual if a module is suspect.
Right-hand rear
corner valve
failure
Air suspension
control module
failure
C1A3501 Reservoir Valve Reservoir valve Refer to the guided diagnostic routine for
general electrical this code on the approved diagnostic system.
failure Refer to the warranty policy and procedures
manual if a module is suspect.
Reservoir valve
block
disconnected
Reservoir valve
block harness
wiring short
circuit to ground
or high resistance
Reservoir valve
block failure
Air suspension
control module
failure
C1A3601 Exhaust Valve Exhaust valve, Refer to the guided diagnostic routine for
general electrical this code on the approved diagnostic system.
failure Refer to the warranty policy and procedures
manual if a module is suspect.
Exhaust valve
disconnected
Exhaust valve
harness wiring
short circuit to
ground or high
resistance
Exhaust valve
failure
Air suspension
control module
failure
C1A3701 Front Cross- Front cross-link Refer to the guided diagnostic routine for
Link Valve valve general this code on the approved diagnostic system.
electrical failure Refer to the warranty policy and procedures
manual if a module is suspect.
Front valve block
disconnected
Front cross-link
valve failure
Air suspension
control module
failure
C1A3801 Rear Cross- Rear cross-link Refer to the guided diagnostic routine for
Link Valve valve general this code on the approved diagnostic system.
electrical failure Refer to the warranty policy and procedures
manual if a module is suspect.
Rear valve block
disconnected
Rear cross-link
valve failure
Air suspension
control module
failure
C1A5501 Ignition Switch Ignition switch Refer to the guided diagnostic routine for
Input Circuit input circuit; this code on the approved diagnostic system.
ignition on while
wake-up off or
ignition off while
engine running
Ignition switch
input circuit short
circuit to ground,
short circuit to
power or high
resistance
C1A681C Left Front Left-hand front Refer to the guided diagnostic routine for
Height Sensor height sensor this code on the approved diagnostic system.
Supply supply circuit Refer to the warranty policy and procedures
voltage out of manual if a module is suspect.
range
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Air suspension
control module
failure
C1A691C Right Front Right-hand front Refer to the guided diagnostic routine for
Height Sensor height sensor this code on the approved diagnostic system.
Supply supply circuit Refer to the warranty policy and procedures
voltage out of manual if a module is suspect.
range
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Air suspension
control module
failure
C1A701C Left Rear Left-hand rear Refer to the guided diagnostic routine for
Height Sensor height sensor this code on the approved diagnostic system.
Supply supply circuit Refer to the warranty policy and procedures
voltage out of manual if a module is suspect.
range
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Air suspension
control module
failure
C1A711C Right Rear Right-hand rear Refer to the guided diagnostic routine for
Height Sensor height sensor this code on the approved diagnostic system.
Supply supply circuit Refer to the warranty policy and procedures
voltage out of manual if a module is suspect.
range
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Air suspension
control module
failure
C1A721C Left Front Left-hand front Visually inspect the wiring harness and
Height Sensor height sensor connectors for water ingress. Refer to the
Mechanism signal voltage out guided diagnostic routine for this code on the
of range approved diagnostic system. Check the
(mechanical) height sensor bracket condition and security.
Check the height sensor for correct
Water ingress to installation and torque of fixings. If any
wiring harness or height sensor fixings are slackened or found
connectors to be loose, or a height sensor has been
Height sensor changed, the vehicle ride height must be re-
linkage calibrated. Calibrate the system using the
disconnected approved diagnostic system. Refer to the
warranty policy and procedures manual if a
Height sensor module is suspect.
linkage damaged
/bent
Height sensor
disconnected
Height sensor
linkage toggled
(now operating in
reverse direction)
Height sensor
bracket damaged
/bent
Height sensor
incorrectly
installed
Incorrect height
calibration
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Air suspension
control module
failure
C1A731C Right Front Right-hand front Visually inspect the wiring harness and
Height Sensor height sensor connectors for water ingress. Refer to the
Mechanism voltage out of guided diagnostic routine for this code on the
range approved diagnostic system. Check the
(mechanical) height sensor bracket condition and security.
Check the height sensor for correct
Water ingress to installation and torque of fixings. If any
wiring harness or height sensor fixings are slackened or found
connectors to be loose, or a height sensor has been
Height sensor changed, the vehicle ride height must be re-
linkage calibrated. Calibrate the system using the
disconnected approved diagnostic system. Refer to the
warranty policy and procedures manual if a
Height sensor module is suspect.
linkage damaged
/bent
Height sensor
disconnected
Height sensor
linkage toggled
(now operating in
reverse direction)
Height sensor
bracket damaged
/bent
Height sensor
incorrectly
installed
Incorrect height
calibration
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Air suspension
control module
failure
C1A741C Left Rear Left-hand rear Visually inspect the wiring harness and
Height Sensor height sensor connectors for water ingress. Refer to the
Mechanism signal voltage out guided diagnostic routine for this code on the
of range approved diagnostic system. Check the
(mechanical) height sensor bracket condition and security.
Check the height sensor for correct
Water ingress to installation and torque of fixings. If any
wiring harness or height sensor fixings are slackened or found
connectors to be loose, or a height sensor has been
Height sensor changed, the vehicle ride height must be re-
linkage calibrated. Calibrate the system using the
disconnected approved diagnostic system. Refer to the
warranty policy and procedures manual if a
Height sensor module is suspect.
linkage damaged
/bent
Height sensor
disconnected
Height sensor
linkage toggled
(now operating in
reverse direction)
Height sensor
bracket damaged
/bent
Height sensor
incorrectly
installed
Incorrect height
calibration
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Air suspension
control module
failure
C1A751C Right Rear Right-hand rear Visually inspect the wiring harness and
Height Sensor height sensor connectors for water ingress. Refer to the
Mechanism signal voltage out guided diagnostic routine for this code on the
of range approved diagnostic system. Check the
(mechanical) height sensor bracket condition and security.
Check the height sensor for correct
Water ingress to installation and torque of fixings. If any
wiring harness or height sensor fixings are slackened or found
connectors to be loose, or a height sensor has been
Height sensor changed, the vehicle ride height must be re-
linkage calibrated. Calibrate the system using the
disconnected approved diagnostic system. Refer to the
warranty policy and procedures manual if a
Height sensor module is suspect.
linkage damaged
/bent
Height sensor
disconnected
Height sensor
linkage toggled
(now operating in
reverse direction)
Height sensor
bracket damaged
/bent
Height sensor
incorrectly
installed
Incorrect height
calibration
Height sensor
harness wiring
short circuit to
ground, short
circuit to power
or high resistance
Height sensor
failure
Air suspension
control module
failure
C1B1862 Supply Voltage Inconsistent Refer to the guided diagnostic routine for
X-Ref Check battery voltages this code on the approved diagnostic system.
received by Air
suspension
control module
Air suspension
control module
supply circuit(s)
short circuit to
ground
Air suspension
control module
supply circuit(s)
high resistance
Air suspension
control module
failure
C1B1903 Door Status Door status Refer to the guided diagnostic routine for
Signal signal, pulse this code on the approved diagnostic system.
width modulated
failures
Incorrect
software loaded
to Air suspension
control module
Central junction
box to Air
suspension
module harness
wiring short
circuit to ground,
short circuit to
power or high
resistance
Central junction
box fault
Compressor
brush card
temperature
sensor harness
wiring short
circuit to ground,
short circuit to
power or high
resistance
Compressor
brush card
temperature
sensor failure
Air suspension
control module
failure
ECM failure
TCM not
configured
TCM failure
Transfer box
control module
not configured
Transfer box
control module
failure
ABS module
failure
SASM failure
Park brake
module not
configured
Park brake
module failure
Vehicle dynamic
suspension
system module
not configured
ABS module
failure
Electronic rear
differential
control module
not configured
Electronic rear
differential
control module
failure
Instrument
cluster failure
Incorrect
instrument
cluster CAN
configuration
Subsequent
Warning &
Message
Warning -
One Chime.
Message -
SUSPENSION
LOWERED
Meaning -
Vehicle has
lowered to
Access
height
because of
failure of
another
vehicle
system
ABS fault
U041786 Invalid Data Park brake fault Refer to the Network Communications
Received From section of the workshop manual.
Park Brake
Control Module
U042886 Invalid Data SASM not Check the security of the electrical
Received From configured connection. Configure/calibrate the SAS
Steering Angle /calibrated using the approved diagnostic system. Refer
Sensor Module to the Network Communications section of
(SASM) SAS fault the workshop manual.
Terrain
optimization
switch
disconnected
Terrain response
module not
configured
Terrain response
module failure
U1A3562 VIN Data VIN from Configure the instrument cluster using the
instrument approved diagnostic system.
cluster does not
match VIN at
time of calibration
Air suspension
control module
has been
swapped with
another vehicle
Instrument
cluster not
configured
Compressor
brush card
temperature
sensor harness
wiring short
circuit to ground,
short circuit to
power or high
resistance
Compressor
brush card
temperature
sensor failure
Compressor fault
U200701 Valve(s) Valve circuit DTC C1A001D will be set first. Visually
short circuit to inspect the wiring harness and connectors
ground between the Air suspension control module
and the control valves for water ingress.
Water ingress to Refer to the guided diagnostic routine for
wiring harness or this code on the approved diagnostic system.
connectors
Valve harness
wiring short
circuit to ground
or high resistance
Air suspension
control module
failure
U200711 Valve(s) Valve circuit Visually inspect the wiring harness and
short circuit to connectors between the Air suspension
ground when control module and the control valves for
system is inactive water ingress. Refer to the guided diagnostic
routine for this code on the approved
Water ingress to diagnostic system.
wiring harness or
connectors
Valve harness
wiring short
circuit to ground
or high resistance
Air suspension
control module
failure
Valve supply
circuit(s)
intermittent short
circuit to ground
or high resistance
Valve failure
Air suspension
control module
failure
U200767 Valve(s) Valve signal Visually inspect the wiring harness and
incorrect after connectors between the Air suspension
event control module and the control valves for
water ingress. Refer to the guided diagnostic
Water ingress to routine for this code on the approved
wiring harness or diagnostic system. Refer to the warranty
connectors policy and procedures manual if a module is
Valve supply suspect.
circuit(s) short
circuit to ground,
short circuit to
power or high
resistance
Air suspension
control module
failure
1. Key off.