Professional Documents
Culture Documents
Department of Education
Direction: Identify the following signs and symbols. Choose your answers from the box below. Write the letter of the
correct answer.
1. Which system is responsible for providing high voltage surge to the spark plugs at the correct time?
I. It must supply an electric spark with sufficient heat in order to ignite the air fuel mixture in the combustion chamber
of the engine.
II. It must maintain the spark long enough to permit the combustion of all fuel charges in the cylinder of the engine.
III. It must draw the spark to each cylinder combustion can begin at specific time during the stroke of compression for
every cylinder engine.
5. Which part of the ignition system responsible for supplying current to starter in order to crank
6. What component works like a transformer that increases the battery voltage into thousands of volts?
7. Which part of the ignition system responsible for reducing the battery voltage to the coil during engine
operation?
9.Refer to the choices inside the box on item number 7, which of the following belongs to the secondary
circuit?
10.Which of the following are safety measures in checking the ignition system?
A. Do not used ordinary pliers for checking the spark plug lead shorting to ground (earth) in order to
sparking.
B. Disconnect first the negative cable of the battery when checking resistance of coil, cut all wires connected
C. Do not used jumper wire in checking the ignition system for continuity.
D. All of the above.
11. Why it is strictly avoided to use spark test on common lead wire to earth when there is leak gasoline to any
12.What should be the first step of the technician before proceeding to servicing procedures in the ignition
system components?
A. Gather information, regarding the problem to be serviced. If possible ask the driver or the owner of the
vehicle.
C. List all parts or items that has been checked and detected by the used of the appropriate instrument for
D. If possible used service repair manual being your guide for the maintenance and servicing of contact
13.Which of the following are the safety measures in conducting a spark test or triggering test?
I. Do not use conductive pliers with only insulated handle. In high energy ignition system the spark will
II. It will jump around or through the insulation and give a dangerous shock
III.See to it that there is no fuel or fuel vapor near where the spark will occur. The spark will ignite the fuel
III. Do not allow spark to short onto dipstick, cam/rocker cover or battery as this can cause an explosion of
14.In conducting a spark test, what is the first procedure that the technician should follow?
B. Connect battery both positive and negative terminal post, then, switch on ignition switch.
C. Remove the spark plugs from the engine by the use of spark plug wrench.
D. Connect the spark plug no. 1 to high tension. wire no. 1 then, attach ground electrode of the spark plug mm
15.Which part of the ignition coil consisting of several thousand turns of very fine wire located inside or near
II. EXPLANATION
3. Elaborate the steps in conducting spark test using sparkplug tester.10 pts
Republic of the Philippines
Department of Education
Direction: Read and understand each question very carefully. Write the letter of the correct answer.
1. What component is located at the center of the ignition coil, a laminated soft iron or steel?
2. After conducting a primary coil resistance test without resistor, the readings shows 2.6-4.0 ohms. What does the
result indicate?
3. Ronaldo conducted a primary coil resistance test with the use of resistor. The result shows 1.9-2.2 ohms which is
higher than the required ohms or resistance. What is condition of the coil?
result means?
5.What should be the minimum and maximum requirement reading when conducting a secondary coil resistance test with
resistor?
II. SEQUENCING
For nos. 6-15, arrange the following procedure in a correct order of steps.
A. Spark Testing While Engine is Running (1-6)
____6. If there’s no spark, proceed to the triggering test of the primary circuit to determine if there will be
_____8. Used non-conductive pliers /insulated pliers hold the extender about 3/8 inch (10mm) the distance allowed
directly to ground in the black head engine.
_____9. While the engine is running , observe the sparking across the gap.
_____10. Before operating the engine turn it to correct direction of rotation by hand with socket wrench and handle.
_____11. Disconnect the spark-plug cable from the spark plug one by one while the engine is running.
III. ENUMERATION
IV. EXPLANATION
31-35. What should be done if the reading in the resistance test is not within the specified range?
Direction: Make an illustration with explanation of how the primary and secondary circuit
Criteria 5 4 3 2 1
Correctness The illustration is The illustration is Some parts of the Some parts of the Most parts of the
of the correct, clear and correct and illustration is illustration is illustration is
Illustration understandable. understandable but incorrect and incorrect, difficult incorrect, difficult
not clear. difficult to to understand and to understand and
understand but not clear. not clear.
clear.
All parts of the The illustration The illustrations The illustrations The illustrations
Completeness primary and lacks atleast 2 lacks atleast 3-4 lacks atleast 5-6 lacks atleast 7-8
of the Label secondary circuit are labels. labels. labels. labels.
labeled.
Correctness of The explanation The explanation The explanation The explanation The explanation
the Expanation provides correct has atleast 2 has atleast 3-4 has atleast 5-6 has atleast 7-8
sequence of how the incorrect sequence incorrect sequence incorrect sequence incorrect sequence
primary and of how the of how the of how the of how the
secondary circuit primary and primary and primary and primary and
works. secondary circuit secondary circuit secondary circuit secondary circuit
works. works. works. works.
Department of Education
I. IDENTIFICATION
1.
2.
3.
4.
5. 6.
11.
7.
10.
8.
9.
B. Parts of Breakerless Type of Ignition System
12. 13.
14.
21.
20.
19.
18. 15.
16.
17.
18.
II.
ENUMERATION
1. What are the parts of the ignition system? Give at least 4 and its uses. (2 pts each)
2. What are the safety measures in checking the ignition system? Give atleast 3. (1 pt each)
III. EXPLANATION
____28. If spark does not occur, check contact point, condenser, ignition coil, and insulator in the primary lead.
____29. Mark cut on crankshaft pulley align to the specified degrees of spark.
____30.Loosen the distributor assembly fixing adjusting bolt. Ignition switch turn on, turn the distributor assembly go against
rotor rotation, see to it that gap adjusted correctly, then, turn the assembly, by setting contact point gap about to open.
___31.Turn the crankshaft to correct direction of rotation in order to set piston no.1 at compression stroke, both values closed.
Republic of the Philippines
Department of Education
I. IDENTIFICATION
Direction: Identify and fill-in the blanks with the correct answer.
_______________1. It is the point in the distributor assembly that distributes high voltage from coil
center cable to different spark plug.
_______________2. It is a type of distributor assembly that consist of the following parts; contact
point, condenser, springs, lobes, contact set attaching screw, breaker plate, dwell-angle adjusting
slot, vacuum advance unit and primary lead.
_______________3. The rotating parts of the distributor assembly that distributes high voltage from
coil center cable to different spark plug.
_______________4. It is a key-operated main power switch that opens and closes the circuit that
supplies current to the ignition and other electrical system.
_______________5. It is device connected into the ignition primary circuit to reduce battery voltage to
the coil during engine operation.
_______________6. A device that distributes in the ignition system, the rotary switch that directs high
voltage surges to engine cylinders in the proper sequence.
_______________7. A type of distributor assembly composed of the following parts: pick-up coil
assembly, reluctor, pick-up coil, pole piece, mounting bracket, permanent magnet, reluctor teeth,
cap clip, connector, pick up coil lead and vacuum advance unit.
__ ____________8. It is the ignition system component that sets as a transformer to step-
up( increase) the battery voltage into many thousand of volts.
___ ___________9. It is connected across the contact point to prevent arcing and burning. It also
provides the storage of electricity when breaker point opens.
______________10. It is a device in the system that serves as lighter to produce spark on the gap.
____________11. It is a wire connected from the distributor assembly lead wire with insulated
terminal to the negative sign of coil.
____________12. It prevents heat and help to cool the coil.
____________13. It is the center of the ignition coil, a laminated soft iron or steel.
____________14.This winding is surrounded the secondary coil windings which is approximately 200
turn of 20-gauge wire.
____________15.It is winded in the core approximately 22,000 turns of very fine wire.
II. ENUMERATION
1. What are the materials needed in conducting a spark test? Give at least 5 (5pts)
2. What are the safety measures in conducting spark test? Give atleast 3 (3 pts)
III. EXPLANATION