Professional Documents
Culture Documents
986 Group 3 Transmission-Manual PDF
986 Group 3 Transmission-Manual PDF
-.8e;~s:;TL.,,-
Technicallnformation
cardiagn.com
Contents:
Group 3
Transmission,manualtransmission
Foreword
The workshop documentationfor the Boxster model has the designation "Boxster" Technical Manual
and contains Technical Information as well as instructions on Repairs.
cardiagn.com
1 Engine,part 2 (as of Repair Group 15) *4
2 Fuel, exhaust,engine electronics
3 Transmission,manualtransmission
3 Transmission,automatic transmission
4 Runninggear
5 Body
6 Body equipment,exterior
7 Body equipment,interior
8/ 9 Air conditioning/ Electrics
9 Circuit diagrams, part 1 (up to and includingthe '99 model) *5
9 Circuit diagrams, part 2 (as of the '00 model) *6
*1 The two folders with Group 0 are to be regarded as one folder; i.e. file the "TechnicalInformation"
notices only in front of the repair descriptions in the folder "Group0 -Diagnosis, part 1"
(up to Repair Group 45).
*2
Thesecond folder "Group0 -Diagnosis, part 2" (as of Repair Group 69) includesthe further
RepairGroupsbelongingto GroupO.
*3
The two folders with Group 1 are to be regarded as one folder; i.e. file the "TechnicalInformation"
notices only in front of the repair descriptions in the folder "Group1 -Engine, part I" (up to
Repair Group 13).
*4
Thesecond folder "Group1 -Engine, part 2" (as of Repair Group 15) includesthe furtherRepair
Groupsbelongingto Group1.
Foreword
Printed in Germany -34, October 1999 VORW.CHP
Foreword Boxster
*5
The two folders with Group 9 are to be regarded as one folder; i.e. file the 'Technical Information"
notices only in front of the repair descriptions in the folder "Group9 -Circuit diagrams, part I" (up to
the '99 model).
*6
The second folder "Group9 -Circuit diagrams, part 2" (as of the '00 model) includesthe further
circuit diagrams belongingto Group 9.
cardiagn.com
Title page: "Repair"
> Repair Groups: overview
> Table of Contents,repairs
> General/technical data
> Instructions on repairs
As can be seen from the breakdown,the publishedTechnical Informationis in the front part of each
folder -numbered according to the Groups. The Table of Contentsassigned to each Group will be
periodicallyupdated.
Note
Sheets that already exist in the "Boxster"TechnicalManualand are updated or revised and thereby
exchanged by a supplementare designated "Replacementsheet". Revisionsor technical modificationson
pages of these replacementsheets are identified for the user with a vertical bar at the margin.
Foreword
VORW.CHP Printed in Germany -34, October 1999
Boxster Overview of repair groups
cardiagn.com
Group 1: Engine 1
Engine-Crankcase, suspension 10
Engine-Crankshaft, pistons 13
Group 1: Engine 1
Engine-Cylinder head,valve drive 15
Engine-Lubrication 17
Engine-Cooling 19
Group 5: Body 5
Bodyfront 50
Bodycenter,roof, frame 51
Bodyrear 53
Lids,flaps 55
Door front,centrallockingsystem 57
cardiagn.com
Bumpers
Glazing,windowcontrol 64
Exteriorequipment 66
Interiorequipment 68
Passengerprotection 69
Group 7: Body equipment, interior 7
Linings,insulation 70
Seatframes 72
Seatupholsteries,covers 74
Group 9 Electrics 9
Instruments,
alarmsystem 90
Radio,telephone,on-boardcomputer,navigation 91
Windshieldwiperandwashersystem 92
Lights,lamps,switchesexterior 94
Lights,lamps,switchesinterior,theftprotection 96
3 Power transmission
3 Technicaldata (transmissionG 86) 3 1
30 Clutch, control
30 50 37 Removing
Clutch
Disassembling
Bleeding boosttheand clutch
spring:
installing
and assembling
system.
allocation
clutch pedal.
and
clutch. grease specification 30. 1
30 01 07 30- 5
3005 19 30. 7
30 30- 15
cardiagn.com
34 Manual transmission -Actuation, housing
34 01 55 Adjusting
Changing
Removing
Disassembling intermediate
and and checking
installing
and assembling
assembling lever transmission
theshift
transmission shift
(transmission
and transmission console.
selector oilG 86 (transmission cables.
connection) G
case 86 cover G 86) 34- , 1
34 08 19 34- 2a
34 12 19 34- 2e
34 33 15 34- .2m
34 35 19 34- 3
34 35 37 34- .11
34 55 37
(transmission
Disassembling G and 86) assembling transmission case (transmission G 86) 34-19
343737 34 -25
39 0919 Removing
Disassembling and installing
and assembling
differential the (transmission
differential (transmission
G 86) G 86) 39 -1
39 0937 39 -5
39 0815 Adjusting the drive set (transmission G 86) 39-11
-
~
cardiagn.com
'-Y
34350001
cardiagn.com
171~96
Example: CWA 14 07 6
. 3-2
9863_1
3 Technical data (transmission
Printed in Germany -30,
G 86)
1999
Boxster Transmission
cardiagn.com
1 st gear 8 -Transmission case cover
Manual transmission
cardiagn.com
Tightening torques
Retaining
plate,reversinglight
switchon transmissionhousing M8 25 (18)
cardiagn.com
Transmissioncasecoveron
transmissionhousing M8 25 (18)
Switchinterlockon
transmissionhousing M8 25 (18)
Torx screwfor
reverseidler shaft M8 35 (26)
Coverfor interiorshiftrod
on transmissionhousing M8 20 (15)
Balljournalfor releaselever
on transmission housing M8 25 (I8)
Coverfor finaldrive
on transmissionhousing M8 25 (18)
Bracketfor shiftcableson
transmissionhousing MID 45 (33)
Rockerholderon
transmission
housing M8 23 (17)
Gearshiftleveron
interiorshiftrod M6 23 (17)
Transmissionsupporton
transmissionhousing MID 65 (48)
cardiagn.com
Hydraulic mount on
support side part M8 25 (18)
Driveshafton
transmission
flange M8 39 (29)
Clutchslavecylinderon
transmission M8 23 (17)
8
I
6
I
~
0 ~ 0
n
'1)
~
0
0
cardiagn.com
~
[/
r 0
~
0
,t1) 0
~ 0
~
~~;ii)
I!
!
~--- .I
.-~~~
.
L-. -~
I
1 ~O
I (
2 ~ ~o\ J
I .~o I
] ~/
0
~
11 I I
3 4 5
J
~
Boxster Clutch, control
Note:
No. Designation Qty. Removal Installation
Releaselever 1
2 Releasebearing 1 Do not wash out bear-
ings. Replace noisy bear-
ings. Do not grease slid-
ing surface of release
bearing or guide tube
3 Retainerspring
Note
4 Cylinder-head 6
bolt The bolts always must be tightened and loosend in
several steps and crosswise in order to prevent
deformation of the thrust-plate housing
cardiagn.com
5 Thrust plate
7 Pan-head
screw 8 Initialtorque 25 Nm
MIO x I x 50 (18 ftl b.)
Finaltorque 900
9 Needlebush
1
Boxster Clutch, corltrol
cardiagn.com
pedal to move forward abruptly. In order to Containerquantity30 litres = 000.043.203.67
avoid damageI the pedal must be guided
manually.
682 -96
4. The bleeder valve on the clutch slave cylinder 5. Switchoff and disconnect the bleedingdevice.
must be opened until clear, bubble-freebrake Correctthe brakefluid levelif necessary.
fluid emerges.
Use a collecting bottle for precise examination
of the emerging brake fluid for cleanlinessand
freedom from bubbles.
'-
~
>1Jr
cardiagn.com
189 -96
690/1 -96
Note
If the system was open previously(e.g. for com-
ponent replacement),the minimumfilling or
bleedingtime must be 30 seconds.
""
~
Boxster Clutch, actuation
cardiagn.com
with a cotter pin (arrow at No.5). Furthermore,the distancebetweenthe bearing
Important: secure the cotter pin (bend it over). pins of the boost spring is 3 mm less.
465_98
32_1_98
BoxsterpedalsbeforeMod.'98
~---
~~@
~
cardiagn.com
':::- \\\
6x "'..""'. ...
'.
.:.' ~ .
4 .5a :
~
5b / ~
r:;;5)
/ (Ql) ~ ~
~
..'
.'
...:
'. ..
' 5a
"..., '.
(Ql) j
."
5 :
3_c:s;::'>~" ..~~: i
2
? ~
~ 1 :
465_98
~"
\\\
Boxster Clutch, actuation
Note:
No. Designation Qty. Removal Installation
cardiagn.com
Insertthe cotter pin (0'3 mm) boost spring and clutch
intothe assemblybore and pedal lever.
bendover ends. Observeproper allocation
Thenundothe threefastening when replacingthe boost
nutsof the bracket(arrows) spring.* *
and removethe boostspring Observe assemblyand
togetherwith bracketand adjustmentspecification
clutchpedallever (No.6) for the bracket (assembly
instructions under
Installation,step 3)
5a Boost spring bearing 2 Replace if necessary.
Alwaysobserve note with
regard to greasing* *
5b Pin 1 Always observe note with
regard to greasing**
6 Clutch pedal lever 1 Removetogetherwith boost
spring No.5 and bracket
6X Bushings 2 Remainin the clutch pedal Check,replace if
lever necessary.
Lubricate. Use grease
specified*
Lubricate the bushings of the clutch and brake pedals (6X and 14X)with "Optimol, Optitemp LG 2"
grease, part No.: 000.043.203.37 (deliveryquantity: 80 g tube).
* Information can be found in RepairGroup 30 -Servo No. 30 Clutch boost spring: allocationand
grease specification. In the case where lubricatingthe boost spring bearing surfaces is not
permissible,the assemblyinstructions under Installation,steps 2.1 and 2.2 can also be followed.
1
Clutch, actuation Boxster
Removal
Warning 4. Detachdiagnosticsocket.
cardiagn.com
cotter pin (Fig. 478_98).
1. Disconnectbatterygroundcable.
2. Removedriver'sseat(to facilitatework).
3. Removeair duct (A). 5. Detach relaycarrier, unclip and lower into the
The air duct is plugged in, footwell.
86_98
7. There is an assemblybore in the guide rod 10. Undo fastening nuts from boost spring
for the clutch boost spring. Insert a 3 mm ~ bracket (arrows).
cotter pin in this bore, and bend over the Requirement: Boost spring secured with
ends (securing: refer to Fig. 478_98). a cotter pin.
Removeclutch pedal lever together with
8. Removepin between the clutch push rod and boost spring and bracket. The bracket is not
clutch pedal lever. removableon the Boxster before Mod. '98.
cardiagn.com
478_98
Installation
1. Inspect all bearing bushings X for clutch pedal
lever and replace them if necessary. Lubricate
sliding surfaces of the bearing bushingsX
(Fig. 466_98) and the pedal bearing axle
with Optimal, Optitemp LG 2,
part No. 000.043.203.37.
2. Assembleboostspring,bracketandclutch
A -Clutch pedal lever 466_98 pedallever.
B -Brake pedal
C -Steering outer tube
Descriptionin 2.1 or 2.2.
X -Bearing bushings 2.1 BoxsterMod. '98/ partlyMod.'99
2.2 Boxsterfrom currentMod.'99
1 -Retainer
Note
Differenttypes of boost springs can be fitted
in the Boxster.
Observeproper allocationwhen replacingthe
boost spring and/or the bracket.
cardiagn.com
spring components not coated. bracket, bearing pins on the boost spring, and
the boost spring in the boost spring pot).
Grease pin for boost spring (arrow) with mating
bearing on the boost spring push rod, the boost
spring bearing (arrows)and the bearing pins on
the boost spring with Optimol, Optitemp LG 2;
part No. 000.043.203.37.
First remove old grease with solventnaphtha.
~
""'
/
'- Do not lubricate (prohibited) 467_98
Note
Silver bracket (986.423.571.00) and boost
spring with white marking (986.423.081.08
Lubricationnecessary (arrows) 31_1_98 Mod. '98/ partly Mod. '99 or 986.423.081.11
from current Mod. '99) must be used only in this
combinationand installed only in the Boxster.
3. Installationand adjustmentspecificationfor
boost spring bracket.
Install preassembled boost spring bracket
with clutch pedal lever.
Not valid for Boxster vehicles before Mod. '98
(bracket cannot be unscrewedor adjusted).
\
To do this: \
~)
4. 1.+5.
Step 1:
Tighten the three fastening nuts (arrows) only
2. \I~
slightly (the bracket must still be movable),
Step 2:
Tighten the clutch master cylinder to 10 Nm
(7.5 ftlb.) (if the clutch master cylinder was
cardiagn.com
32_98
detached).
Step3: Note
Press the clutch pedal againstthe direction of The push rod of the clutch save cylinder should
travel until the pull stop in the clutch master not be lubricated in general (for all versions).
cylinder is reached.
4. Fit new retainer on the pedal bearing axle.
Step 4: On vehicles as of Mod. '98, subsequently
Removecotter pin (retaining pin) on the spring secure the retainer by wedging it with a
cup so that the clutch pedal is pressed against mandrel.
the rubber stop in the boost spring bracket.
5. Install clutch pedal switch.
Step 5: First pull operating plunger out of the switch
The bracket is screwed down with the clutch as far as it will go.
pedal pressed back (to make full use of the By means of its self-adjustmentfunction,the
slots). Tighten hexagon nuts (arrows)in the switch then compensatesfor tolerances in
prescribed sequence.Tighteningtorque: the pedals.
7.5 Nm (5.5 ftlb.),
Sequence: Sa / Sb / Sc
.
Printed in Germany -24, 1998 986307
~-::::?'
Clutch, actuation Boxster
6. Checkthe interlockswitchadjustment
on
vehicleswith interlock.
cardiagn.com
49_98
7. Installrelaycarrier,diagnosticsocketandair
duct.
cardiagn.com
Boost spring with white marking. Observe
Note replacement procedure and grease specification.
~"'r~ ~
31_98
* Distinction(ldentification
469_98
cardiagn.com
very of the boost spring.
469_98
47O_98
'"'"
,',
3.2 Boxster Mod. '98 partly Mod. '99
(boost spring bracket can be unscrewed)
467_98
Note 4. Greasespecification
The hexagon bolt 999.423.315.06 and the
fuse 999.166.022.02 for connectionto the It is essentialto observe the following
optimised clutch pedal are included in the grease specificationduring assembly
scope of delivery of the boost spring. work on the pedals.
This corresponds to the same scope as for
4.1 Pedal bearing axle
the boost spring version No.3 (from current
Mod. '99). Lubricationrequired in most cases.
Greasethe bearing bushings marked X and the
pedal bearing axle with Optimal, Optitemp LG 2,
Part No. 000.043.203.37.
cardiagn.com
as standard and in the event of replacement.
1 -Retainer
4.2 Push rod of clutch master cylinder 4.3.2 Boxster Mod. '98 partly Mod. '99
(boost spring bracket can be unscrewed)
Do not grease, as this could cause damage.
A. Standard boost spring:
Push rod open on one side. Componentnot
coated.
4.3 Spring boost area Grease pin for boost spring (arrow)with mating
Lubricationmay be required or prohibited, bearing on the boost spring push rod, the boost
according to the spring boost version. spring bearing (arrows)and the bearing pins on
In general,the following applies: Do not grease the boost spring with Optimol, Optitemp LG 2,
coated components,as this erodes the coating. part No. 000.043.203.37.
First remove old grease with solventnaphtha.
4.3.1 Boxster up to Mod. '98
(boost spring bracket cannot be unscrewed) The boost spring and the boost spring housing
A. Standard boost spring: are greased with a special grease on the inside.
Push rod open on one side. Componentnot This grease is not availableas a spare part.
cardiagn.com
coated. Replacethe entire boost spring (with boost
spring housing)if necessary.
Grease pin for boost spring with mating bearing
on the boost spring push rod, the boost spring
bearing and the bearing pins on the boost
spring with Optimol, Optitemp LG 2, part
No. 000.043.203.37.
First remove old grease with solvent naphtha. ""
31_1_98
/ '.
cardiagn.com
.""\
467_98
Note
cardiagn.com
3. Cleanthe drain and filler screw.
Tools
cardiagn.com
No. Designation Special tool Explanation
Lockingbridge 9619
Removal
1. Removecentre console (see Group68, Inte- 4. Disengagethe selector and shift cables on
rior equipment). the shift console. To do this, slide the locking
sleeveforward as far as it will go and turn it
2. Shifttransmissionto neutralandfix shiftlever clockwiseto removalposition.
withspecialtool 9619.
9619
cardiagn.com
==:=;;:
- -<-
-~
602-96
3. Removeshiftconsolecover.
1 -Selector cable (blue) 603-96
2 -Shift cable (black)
3 -Adjuster open
4 -Adjuster closed
5 -Support bracket
~
Boxster Manual transmission -Actuation, housing
Installation
Note
/
Preconditionsfor this are:
cardiagn.com
~ ..;..
~f/.J~2.]3 ~ ~
/5/ /,
_/ /
Note ./
;\/~!
Boxster Manual transmission -AI~tuation, housing
Tools
cardiagn.com
459-97
...
...
.-'
/
'-" ~ :,
7
cardiagn.com
./
'"...
3
JlJ
t
3
~
595-96
1 -Selector cable (blue)
2 -Shift cable (black)
3 -Spacer nut
4 -Holder
5 -B+ wire
6 -Holder
'/
~
Boxster Manual transmission -Actuation, housing
Removal
Note
The shift cable and selector cable can be 3. Disengageshift and selector cables on the
exchanged onlytogether, as they possess transmission.
a common locking piece. Until date of manufacture 21.4.97
cardiagn.com
-
--.J
~
~
\.
Note
The shift and selector cables must not be
excessivelybent or kinked.
C-:
:::;.;.;-
Manual transmission -Actuation, housing Boxster
Note
The transmission shift lever must be removed
so that retaining clip "A" can be removed.
To do this, remove retaining clip "G", unclip joint
rod at the top and unscrew securing screw "F",
cardiagn.com
(refer to Workshop EquipmentManual, 7. Disengageshift and selector cables on the
Chapter2.4, No. 21) shift cor]sole. To do this, slide the locking
sleeveforward as far as it will go and turn it
clockwiseto removalposition.
4 ~~
~
,...'
/
#.
',/'/i
1 ~
(
482-97
:::22
~
~
Boxster Manual transmission -Actuation, ass. housing
--
cardiagn.com
AI \.
/ ~
B-.=::::::;:
-AI \
\\~ ,p1~:;;;'
..~.+::
'::'~\":,:~'!""I;(
'\i
604_96
."/i
,\
\\\
\\\ ~~~:\!;!
A -Shift and selector cables 604_96
B -B+ wire
Installation
The shift and selector cables are designed so
that installationand adjustmentare a single
work step.
Preconditions
for this are
--
,.,-
Manual transmission -Actuation, ass. housing Boxster
Note
Alwaysreplace micro-encapsulatedsecuring
screw "F"and tighten to 23 Nm (17 ftlb.).
604_96
cardiagn.com
lever support. Tighteningtorque of the
fastening nuts: 10 Nm (7.5 ftlb.).
:-~,
;f&
~
~
671-1-96
2
cardiagn.com
i.::.j~
~
5 ..,/
~/
\/
:;/
:::22
1 -Selector cable (blue) 603-1-96
2 -Shift cable (black)
3 -Adjuster (open)
4 -Adjuster (closed)
5 -Support bracket
7. Clipin shiftconsolecover
"':;:-~
~
Boxster Manual transmission -Actuation, housing
Tools
~ > - S~p~~;:=:
A177USA
y..
cardiagn.com
c
477-97
A Removaltool Commerciallyavailable
(refer to Technical Equipment
Manual,Chapter 2.4, No. 21)
B Threadedpiece VW771/15
c Hexagon-headbolt Commercially available;
M10x 110 make a 5mm wide and 3 mm
deep groove in the head.
cardiagn.com
461-97
Transmission connection:
A -Relay shaft
B -Shift lever
C -Intermediate lever
D -Stop cap
E -Lock nut
F -Rubber washer (as of date
of manufacture 22.4.97)
Note
The intermediate lever is machine-caulkedas
standard after adjustment of the shift
mechanism.
If the transmission connection or parts of the
transmission connection are replaced during
repairs, the caulked intermediatelever must be
exchangedfor an adjustableintermediatelever
and readjusted.
cardiagn.com
1 st, 2nd, 5th or reverse gear cannotbe
engaged.
461-97
1. Move shift lever to neutral position and
disengage shift cables on the transmission. Transmission connection
Use a commerciallyavailableremovaltool for
this purpose (refer to Workshop Equipment A -Relay shaft
Manual,Chapter 2.4, No. 21) B -Shift lever
C -Intermediate lever
2. Disengageend piece of intermediatelever D -Stop cap
at shift lever "8", E -Lock nut
F -Rubber washer (as of date of manufacture
22.4.97)
Note
The face sides of the intermediatelever end
pieces must be at right anglesto the centre
axis of the ball pins.
cardiagn.com
484-97
Note
Ball socket and ball pin versions with retaining
clips must be lubricated with a light coat of
Universallow-temperaturegrease.
Do not grease ball socket and ball pin
versions without retaining clips (as of date of
manufacture22.4.97).
cardiagn.com
Tools
cardiagn.com
233-96g
Removal
1. Secure engine in installationposition on the 9. Unscrewthe clutch slave cylinder and hang
transport carrier with special tools 10 -222 A up at the side with the hose connected.
and 9591/1.
Note
The clutch pedal must not be pressed if the
slave cylinder has been removed.
Danger of injury from flying piston rod.
Affix a warning note in the vehicle!
cardiagn.com
194-96
3. Removestabilizerbar.
cardiagn.com
right-hand sides.
11. Disengage shift cables on the transmission.
As from date of manufacture 22.4.1997 Note
"--"
I.,
AI
..\ c
-.-:::./""?~~~--
462-97 435-97
A = Transmissionsupport
B = Hydraulicmount
12. Place a transmissionjack underneaththe C = M12 Fasteningnut
transmission and secure the retaining strap,
--
'\.J-
I~
1
Manual transmission -Actuation, housing Boxster
cardiagn.com
193-96
A = Washer
193-96
Installation
Installation is performed in reverse order, taking
the following points into account.
Stabilizer mount to
stabilizer bar (M1 0) 46 Nm (34 ftlb
cardiagn.com
Drive shaft to trans-
mission flange (M8) = 39 Nm (29 ftlb.)
Transmissionprop to
transmission (MID) = 65 Nm (48 ftlb.)
Gearshiftlever on interior
shift rod (M8)* = 23 Nm (17 ftlb.
* Note
Tools
cardiagn.com
2
25 22
I
~~~~~;~~~~~
18 -~ @'i!-- ~
cardiagn.com
19 /F,'l
24
17
16
21 """
20 ~ '26
/~~ 4-
c1:J:
27
23
"
Manual transmission -Actuation, housing Boxster
Note
If the 5th and reverse gears stick or catch after adjustmentof the gear changing mechanism,before re-
moving and disassemblingthe transmissionfirst remove the lock for the 5th and reverse gears, inspect it
and, if necessary,replace it (see Page 34 -32)
Note:
No. Designation Qty. Removal Installation
cardiagn.com
grease and drive it in as
far as it will go using the
special tool VW 192
9 Hexagon-head
bolt 1 Tighteningtorque 25 Nm
(18 ftlb.)
10 Tab washer
Note:
No. Designation Qty. Removal Installation
cardiagn.com
17 Spacer 1
18 Torx screw 1 Tightening torque 40 Nm
(29 ftlb.)
19 Spacer
22 Input shaft
23 Output shaft
24 Relayshaft 1
25 Shift rod and shift fork, 3rd
and 4th gears
26 Interior shift rod 1
27 Shift rod with shift fork for 1 Replacethe shift rod for
1 st / 2nd / 5th and 5th and reverse gears
reversegears only as a complete
assemblywith shift
fork and driver
Disassembly 3. Pull the ball bearing for the input shaft out of
the transmission housing using the special
Note tools V.A.G. 1582 and V.A.G. 1582/2.
cardiagn.com
~ 540 and drain off the gear oil.
43-96
A = Puller with grip
,
c
E
42-96
44-96
-E
Boxster Manual trar,smission -Alctuation, housing
Assembly
1. Assemblethe input and output shafts with the
shift rods and install them together in the trans-
~-$/
mission housing. I ~I
46 -96
3. Installthe switchinterlock.
cardiagn.com
Pushthe locking slide to the center position
and ensure that no gear is engaged.
45 -96
Insertthe switchinterlock.
2. Insertthe relayshaftandthe interiorshiftrod, Guidethe relayshaftintothe switchinterlock.
~1.
Manual transmission -Actuatioln, housing Boxster
Note
Tighten the screws -B -only by 1/2 of a turn
cardiagn.com
each so that the ball bearing is not tilted and
thereby damaged.
47 -96
Tools
cardiagn.com
6
2 Threadedpiece VW771/15
3 Pressurepiece 9247/1
4 Pressurepiece VW295 a
5 Pressurepiece 3005
6 Pull-intool andextractor P 254
7 Threadedadapter Standard
(MIO/M8) (e.g. Messrs. Kukko 18 -008 A)
14 17 .""""~-15
16
~ ~~..""'I~:~~,"
./ ~ I
I
'"""""'~~')
,..
cardiagn.com
.~ \ . v
.~ ~
~. .
A/.~'/~r.)~t~
~~J --~1
I
12
I
13 I~
I
I ~ I
~
i:""~::.P"'1 5
6
i 2 3 4
~
'1
1
~
Boxster Manual transmission -Actuation, housing
Note:
No. Designation Qty. Removal Installation
cardiagn.com
7 Retainingsleeve 1 Force out with a suitable Do not reinstall (required
internal puller and special only during manufacture
tool VW771 in Production)
8 Tapered roller bearing 1 Removewith the special Press in with the special
outer race tools VW 771, VW771/15 tool 3005 and a suitable
and standardthreaded plunger (e.g. special tool
adapter WI 407)
9 Adjusting shim "S4" x Note the thickness for Measureagain if
refitting necessary(see Page
39 -15 and 39 -25)
10 Pressure plate 1
11 Rubber disc 1 If necessary,drill a hole in Replace if necessary
the disc and pull out with a
sheetrnetalscrew
Note:
No. Designation Qty. Removal Installation
cardiagn.com
and a suitable internal
puller (e.g. Kukko 21/4,
23.5 -30 mm)
Disassembly
1. Removethe outer race for the small tapered
roller bearing using special tools VW 771, VW VW407
771/15 and a commerciallyavailable
threaded adapter (MID/M8).
3005
-
'0
ki' 57 -96
\
cardiagn.com
2. Press in the needle roller bearing for the input
\,\\
shaft in the correct position with special tool
~1\ \fIN 295 a.
Measurethe installationdimensionfrom the
_\\ cover upper edge to the bearing upper edge.
56-96
Assembly
1. Press in the outer race for the small tapered
roller bearing using special tool 3005. ,t ~
~
6"~,
@
~(,
"'W':'
/(Q
I'a"=216mm 58 -96
.
5
~
34 55 37 Disassembling
Printed in Germany, 1996
and assembling transmission
9863419
case cover (transmission G 86) 34 -23
Manual transmission -Actuation, housing Boxster
cardiagn.com
"a" = 1 mmi 59- 96
Tools
1
mmf:J:mmm
~ 2 r; I 6 7
\\~:~
cardiagn.com
3 9
4 ~ ~;:~-:;*~~~~V;:;id 6)12
?- -0)
5
~ ~
10 11
~
13
~
34 37 37 Disassembling and assembling the transmission housing (transmission G 86) 34 -25
Printed in Germany, 1996 9863425
No. Designation Special tool Explanation
1 Stri~ingtool \IW 771
2 Bridlge \!IN 771/29
3 Pu"lintoolandextractor P 254
4 Driv~~nmandrel \!IN295
5 Hoqk VW681
6 pre$sure piece 9247/4
,
7 Pre$surepiece 3128
8 Pre$suredisc VW511
9 Pre$surepiece 30 -205
.
10 Pre$surepiece 40-202
cardiagn.com
Pre~surepiece 9247/1
12 DrivF~n
mandrel V'N 195
13 Thr~adedpiece V'N771/15
cardiagn.com
Note:
r~o. Designation Qty. Removal Installation
5 Rev,rsing
lightswitch 1
6 Torqidalsealingring 1 Alwaysreplace,lightlyoil
7 Capl
cardiagn.com
8 TaPfredrol~erbearing 1 Pulloutwith special Press in with a suitable
out~rrace tools 3128 andWI 771/29 pressure piece
Note:
No. Designation Qty. Removal Installation
16 Toroidalsealingring 1 Alwaysreplace,lightlyoil
17 Shaft seal 1 Pullout with the special Fill the chamber between
tool vnN681 (also possible the dust lip and sealing
cardiagn.com
with transmission installed) lip with multi-purpose
grease. Drive in in the
correct position using the
special tool VW 195 (5.5
mm under the upper
edge of the cover)
18 Tapered roller bearing 1 Drive out with a suitable Press in with the special
outer race (small) * aluminiumor copper tools
mandrel (~6...8 mm) 30 -205 and VW295
19 Adjusting shim "S2" x Note the thickness for Remeasurethe thickness
reinstallation if necessary
20 Adapter
21 Balljournal 1 Tighteningtorque 25 Nm
{I8 ftlb.}
22 Sleeve 2 Press in in the correct
position
23 Transmission
housing
24 Oil filler screw 1 Tighteningtorque 25 Nm
(18 ftlb.)
25 Shaft seal 1 Sameas No. 17 same as No. 17
Note:
No. Designation Qty. Removal Installation
Note
If the parts marked with an .(asterisk) are replaced, readjustmentis necessary(see Page 39 -11).
cardiagn.com
Disassembly Assembly
1. Pull out the tapered roller bearing outer race 1. Press in the needle roller bearing for the input
with the special tools 3128 and VW771/29. shaft in the correct position, using the special
tools VW295 and 40 ~202 (do not strike).
cardiagn.com
A = sqrew MID x 135 92 -96
t
94 -96
y
~~
2T
93 -96
II!
2. Press-in~epth of the sleeve for transmission
venting. I
96 -96
1 -Plastic bushing
2 -Toroidal sealing ring
cardiagn.com
a = 21:t q.5 mm 95 -96 3 -Bushing with lock for 5th and reverse
gears
3. Assembl~instructions for the lock for 5th 4 -Spring
and reve~segears
4. Assemblyend position of the lock for 5th
Insert t e spring "4" into the plastic bushing andreversegears.
"1" and urn it counterclockwiseunder slight
pressur until the spring engages at the The lug (arrow A) of the bushingfor 5th and
base of the plastic part. Positionthe bushing reverse gears must alwayscome to the stop
"3" onto the spring so that the bent spring opposite to the groove (arrow B) of the plas-
end lies in the groove providedfor that pur- tic bushing.
pose. P ess the spring together with the
bushing"3", tighten by approx. 1 turn
counter lockwise (to the left) until the lug of
the bus ing "3" is above the groove in the
plastic ushing. Press the lug of the bushing
"3" into he groove of the plastic bushing"I"
as far a the stop surface. Turn the bushing
"3" cloc wise (to the right) and release it.
The bus ing "3" springs into the assembly
end position.
97 -96
Tools
0 4
cardiagn.com
No. Designation Special tool Explanation
1 Tubular piece 9238
2 Pressureplate VW 401
3 Pressureplate VW402
4 Measuringbridge 3167
{:)
1 ""~ 21
1 """""""'IB
20
cardiagn.com
./
1 i (iff'~19
~~ "" 1
0 2
'e~,-"'-""-::---=
~---/ - 3
~4
'I~I---""
(::) "" 5
6 9==7
8
~I~r---~~~ 11
0
cardiagn.com
the same gear wheel
6 Selectorsleeve 1 Pay attention to the instal-
lation position
7 Snap ring (color blue) 1 Markfor refitting Remeasurethe snap ring
if the input shaft and syn-
chronizing elementNo.8
are to be replaced
8 Synchronizingelement 1 Press off Heat up to approx.
100 °C and press on
{high collar faces the 3rd
gear loose gear wheel}
9 3rd gear synchronizing
ring 1 Sameas No.5 Same as No.5
1
Manual transmission -Gears, shafts, into gearsh. Boxster
Note:
No. Designation Qty. Removal Installation
cardiagn.com
17 Ne~dle-roller
bearing 1 See Page 34 -28 See Page 34 -28
18 Tralnsmission
housing
19 Ne,dle-roller
bearing 1 See Page 34 -22 See Page 34 -22
21 Tr~nsmission
casecover 1
cardiagn.com
VW402
A = Separatingdevice 89 -96
r1
cardiagn.com
~ 83 -96
c B
4. Determinethe snap ring for the 4th gear.
To do this, determine the thickest ring which
can still just be used.
1162 -35
85 -96
1179 -35
Note
Deter~ine the snap ring for the 5th gear in
exactlylthe same way.
5. Hea
i the synchronizing elements for the 3rd
cardiagn.com
.
"."
/
VW 401
"""""
"»»"'"
0' -~
9238
VW 401
1. Cla~pthe inputshaftin the visewith protec- 3. With a depth gauge, measurefrom the
tiveliaws. housingto the lower input shaft groove.
cardiagn.com
Dimension"a" = 28.5 mm 64- 96
'-
...
"
"
Dimension
"b" = 26.8 mm 63 -96
~
35 Manual transmission -Gears, shafts, into gearsh. Boxster
5. Measurelthethickness of the lower snap ring 8. Determinethe thickest snap ring which can
(No. 8, ~age 34 -14): still just be used.
Dimension"x"
x=a- ~
= 28.1 -26.8 mm
= 1.7 mm
~
6. Measurelthe
thicknessof the snapring in
accorda~ce
with the table:
Measurement thickness
result
cardiagn.com
(mm)
65 -96
(mm)
1.48...1)56 1.54
1.57...1)65 1.63
1.66...1)74 1.72
1.75...1)83 1.81
1.84...1192 1.80
1.93...2(01 1.99
2.02...2~10 2.08
2.11...2(20 2.17
2.21...2~27 2.25
2.28...2~35 2.33
Tools
cardiagn.com
100-96
-,
8-0 iI ..
I
9-9 II
Ii.
35
cardiagn.com
I
10-. I
I /34
12--0 I
"'=='
13--@ L, .lr33:=
14J::I V- 32
r-31
15-0
20~ ~~/-1
16~ (~Z~ 2
17--0 (:, 3
18-0 'C:::)---4
0..."'-- 5
191 0---6
~;~"- 7
~11
L j ~
,36
--1
~
Boxster Manual transmission -Gears, shafts, into gearsh.
Note:
No. Designation Qty. Removal Installation
cardiagn.com
the reverse gear
(see Page 35 -17).
5 Needle-rollerbearing 1 Mark for refitting Fit with the same gear
wheel
6 Snap ring * 1 Mark for refitting Remeasureif necessary
(colour blue)
Synchronisingelement 1 Using a suitable separating Heatto approx. 1000 C
device (e.g. Kukko 17/2), and press on (high collar
press off together with the facing the 5th gear loose
5th gear loose gear wheel gear wheel)
8 5th gear synchronisingring 1 Same as No.3 Same as No.3
Note:
r~o. Designation Qty. Removal Installation
13 4th gear fixed gear wheel* * 1 Press off with special tool Heat up to approx.
VW402 laaoG and press on in
the correct position
(groove or high collar
faces 3rd gear)
14 Sna~ring * 1 Sameas No.3 Sameas No.3
15 3rd gear fixed gear wheel 1 Sameas No. 13 Same as No. 13, groove
faces 4th gear
16 2nd gear loose gear wheel 1 Same as No.2
cardiagn.com
(seePage35 -17).
19 Needle-roller
bearing 1 Sameas No.5 Same as No.5
21 Snap ring *
1 Same as No.6 Same as No.6
(col6ur blue)
25 Needle-roller
bearing 1 Sameas No.5 Same as No.5
27 Tapered roller bearing 1 Press off with tapered Heatto approx. 100 °C
inner race roller bearing outer race and press on with a
and special tools VW401 suitable tubular piece
and VW402 (e.g. special tool
VW415 a). Press again
after heat exchange
1
Boxster Manual transmi~ision -Gears, shafts, into gearsh.
Note:
No. Designation Qty. Removal Installation
cardiagn.com
34 Pressure plate 1 See Page 34 -21
36 Transmission
cover 1 See Page 34 -22
37 Transmission
housing 1 See Page 34 -25
* Note
Since snap rings of different sizes and thicknessesare used,the individualsnap rings must be identified
(e.g. with numbers).The thickness of the individualsnap ring must be determinedagain if a directly af-
fected romponent is replaced.
Catalog!ue).
1
Manual transmission -Gears, shafts, into gearsh. Boxster
Dlisassembly Assembly
1. Check the synchronisingrings for wear.
Note To do this, press the ring into the shift sleeve
Whenrepla ing the tapered roller bearings and measurethe gap dimension"a" with a
(No.1 and o. 27), determine the installation feeler gauge in positions A, Band C.
position bet re removing the output shaft (see Add up the measuredvalues and divide by 3.
Actual Mea urementon Page 39 -17). The value obtained must not be below
O.5mm.
1. Press offl the tapered roller bearing inner race.
.
The oute~race must be used for this purpose.
cardiagn.com
'- 'B
1162_35
cardiagn.com
3. Installthe selector sleeves in the correct posi-
tion. The slanted side (arrow 1) faces the
reverse gear loose gear whee! (No.2) in the
case of the 5th and reverse gear selector
sleeve,and it faces the 2nd gear loose gear
wheel(No. 16) in the case of the 1st and 2nd
gear selector sleeve.
7 9 2
cardiagn.com
'"."(oj \ /'
~ "-
1 2 3 4 8 5 6
53.96
,.
:~(
1
/"-.-
~
Boxster Final drive -Differential, differential lock
Note:
No. Designation Qty. Removal Installation
cardiagn.com
6 Speedometer-drivegear 1
7 Tachometer sensor 1
9 Transmissionhousing 1
* Note
In this transmission,
the speedometer-drive
gear andtachometersensorhaveno function.
Removal Installation
1. Removethe flanged shaft.
To do this, place a chisel or spacer "A"under Note
the flanged shaft and pull out the flanged shaft The flanged shafts are installed with polygonal
by turning the screw "8", bearings. The rough running of these
bearings when the flanged shafts are not
installed does not indicate that the
bearings are faulty. The polygonal bearings
can be replaced only with the flanged shaft.
cardiagn.com
with the new snap ring "A".
\i
39250001
Tools
lO~
'~~~~;~~~~~~
?
cardiagn.com
,
E
39090001
~,?' ~.\
~
,~
r
~-'~:::~1
-
17
\~~~~~~ -
;~
~,~~~i~~;~~~~~~=~:;;~~~~~~==
-= ~ -===~?J=
c \-." Q ~ ~
16 :~~~~ _!!-
5 _..:~~
cardiagn.com
3 -_= ~_4~
~
5
9 "
11
7~~3~ 4
8 . ~G~2
10 ~~, 1
12
13
14
49-R-96
./
---0:-
~
1
'\':"-"":~.
Boxster Final drive -Differential, differential lock
Note:
No. Designation Qty. Removal Installation
1 Speedometer-drivegear 1
2 Tapered roller bearing 1 Removewith commercially Heat to approx. 1000 C,
inner race' availabletwo-arm puller and put into position and
special tool P 263 press again after heat
exchange
3 Tapered roller bearing 1 Same as No.2 Sameas No.2
inner race *
cardiagn.com
continueturning with a
rotational angle of 45°,
5 Crown wheel' 1 Force off with a mandrel If required, heat up to
through the threaded holes approx. 1000 C
6 Dowel pin 1 Drive in in the correct
position
7 Axle 1
8 Differential bevel gear 2
(small)
9 Differentialbevel gear 2
(large)
10 Thrust washer assembly 1 Insert with gear oil
Differentialhousing* 1
12 Tapered roller bearing 1 Drive out using a suitable Press in with special
outer race aluminiumor copper tools VW511 (or 2050)
mandrel(0-6...8 mm) and VW295
13 Adjusting shim "S1" x Note the thickness for Remeasurethe thickness
installation if necessary
14 Coverfor final drive. 1 Seal with Loctite 574
Note:
r~o. Designation Qty. Removal Installation
* Note
If the parts marked with an * (asterisk)are replaced, readjustmentis necessary(see Page 39 -13).
cardiagn.com
Disassembly
1. Forcethe crownwheeloff the housing.
c:..:>
c:..:>
<..) ("")
51 -96
cardiagn.com
2. Heat up the crown wheel to approx. 100 DC
and put it into position.
50 -96
Assembly
1. Installthe differentialbevelgears.
Insertlargedifferentialbevelgearsandfix
them with the flanged shafts (without snap
ring).
52 -96
Insertthe small differentialbevel gears offset A = Use centering pins (shop-made)
by 1800 and swivel them in by turning the for guidance.
flangeshafts.
Alignthe thrustwasherassemblyandsmall
differentialbevelgears.
Tools
cardiagn.com
18O_99
lrools
No. Designation Special tool Explanation
1 Centring disc VW 385/4
cardiagn.com
7 Dial gauge extension V'N385/56 30 mm long
10 Clampingsleeve VW521/12
11 Adjushnentdevice VW 521/4
12 Measuringlever VW388
16 Measuringmandrel VW385/1
17 Holder VW792/1
18 Holder 3177
19 End plate V'N385/33
20 Lever VW296
General
Careful adjustmentof the output shaft and crown wheel are crucial to the service life and smooth running
of the final drive. Therefore, output shafts and crown wheels are paired with each other as early as during
manufactureand are checked by special inspection machinesto ensure that the tooth bearing is in a
good position and that there is low noise in both rotation directions.
The deviation"r" referred to the master gauge "Ro"is measuredfor the drive sets supplied as spare
parts and is recorded on the outer circumference of the crown wheel. Everydrive set (output shaft and
crown wheel) must be replaced only together.
cardiagn.com
cardiagn.com
173 -96 155 -96
Vo -Hypoid offset
Whencarrying out assemblywork on the final drive, readjustmentof the output shaft and crown wheel or
drive set is necessaryonly if parts are being replaced which directly influencethe adjustmentof the final
drive. In order to avoid unnecessaryadjustmentwork, pay attention to the following table:
cardiagn.com
Transmission
case x
cover
Differentialhousing x
Taperedroller bear- x
ing for output shaft
Driveset x x
Cover for final drive x
-
~
~
~
cardiagn.com
-
154 -96
If the output shaft and crown wheel haveto be 3. Divideup the total disc thickness"Stot" in S3
adjusted, it is best to follow the sequence below and S4 so that the measurementfrom the
in the interest of rational working: crown wheel center to the front of the drive
pinion correspondsto the installationdimen-
1. Determinethe total disc thickness "Stot" (Sl sion "R" measuredduring production.
plus S2) for the correct preload of the tapered
roller bearings/differentials. 4. Divideup the total disc thickness "Stat" in Sl
and S2 so that the stipulated circumferential
2. Determinethe total disc thickness "Stot" (S3 backlashis present betweenthe crown wheel
plus S4) for the correct preload of the tapered and output shaft.
roller bearings/outputshaft.
H
Boxster Final drive.. Differential, differential lock
cardiagn.com
tion "r". Note the value.
Readjustmentof the output shaft in accordance Fit the inner races for the tapered roller bear-
with the instructions below is necessary only if Ings
the drive set is replaced. If other parts which (see Rep. Gr. 35, Disassemblingand assem-
also influencethe output shaft position are bling the output shaft).
changed,make the adjustmentvia the previously Secure the lower tapered roller bearing
determined installationposition. (arrow).
(See Page 39 -17 for actual measurement).
cardiagn.com
Install the outer races for the tapered roller
bearings without adjusting shims in the trans-
mission housingor in the transmissioncase
cover. Alwaysuse rubber washer and press-
ure plate for measuringthe disc thickness
and for measuringthe S4 disc.
172 -96
Note
Pressureplatesof variousthicknessescanbe in- Placethe transmission
housingon the work-
stalled. bench.
Using the special tool VW296, press on the Turn the transmissionthrough 1800 so that
output shaft head until the tapered roller the transmissioncase cover faces upwards.
bearinglouter race fits closely in the trans-
missionicase cover.
cardiagn.com
158 -96
Stat. = Measurementresult
+ pressing
;0
~ I" Pressing
I (constantvalue) 0.15 mm
Measurementresult +1.45 mm
Stat. 1.60mm
0 -o.~
157 -96
1-
Boxster Final drive -Differential, differential lock
cardiagn.com
Screw the screw into the shaft head in order to
turn the output shaft. Adjustthe setting collar of the special tool
VW385/1 to the dimension"a" = 35 mm,"
Fit the measuring tools.
Adjust the movable setting collar
to the dimension "b" = 65 mm.
~ ~
39080001
cardiagn.com
39080003 output shaft head and displays the max,
deflection (reversingpoint), The measured
Set the master gauge, special tool 385/30, value is the dimension "e"(black number
to the dimensionRo = 59.65 mm and range),
place on the measuring mandrel.
Set the dial gauge (3 mm measurement Example0.46 mm
range)with 1 mm preload to "0".
L- -.,)
"~I
- 1M
3908005
39090004
S4 = Stat. -S3
Example
cardiagn.com
Note
Pressure plates of 14.8 mm or 15.3 mm can
be installed.
Example
cardiagn.com
39080005
.
39 -24 39 08 15 Adjusting the drive set (transmission G 86)
5186395 Printed in Germany -30, 1999
Boxster Final drive ..Differential, differential lock
cardiagn.com
Prel 1.00 mm
~ VW 387 Read-otfvalue
X =
0.88 mm
0.12 mm
Adjustingshim $4 0.77 mm
Value X + 0.12 mm
New shim thickness $4 0.89 mm
Note
Note
Handlethe holder and dial gauge with care so
that they do not become misadjusted.
cad
Boxster Final drive -Differential, differential lock
Determining the total disc thickness "5tot." 6. Secure the special tool VW 387 with the dial
(51 + 52). gauge and extensionto the housing,and set
Readjustmentof the crown wheel is necessary if to "0" with 1 mm preload.
are replaced.
Note
The output shaft must be removed in order to
determine the preload of the tapered roller
I
bearings on the differential.
cardiagn.com
1. Removethe sealing rings and tapered
roller bearing outer races for the differential A = Dial gauge extension, 182_99
and take out the adjusting shims approx. 30...40 mm long
(seelPage 34 -27). 7. Move the differential up and down. Read off
and note the play at the dial gauge.
2. Install the tapered roller bearing outer races
Example: 1.42 mm
without adjusting shims (see Page 34 -27).
_99
Note Note
Whenmeasuringthe play, do not turn the Whenreadjustingthe drive set, also adjust
differential,otherwise the measurement the output shaft and perform a check
result will be corrupted. (see Page 39 -19).
8. Calculate"Stat.".
"Stat." = measurementresult + pressing.
Example
Measurementresult 1.42mmmrn
Pressing (constant value) + 0.50
"Stat," = 1.92 mm
cardiagn.com
outer race in the transmissionhousing.
~ 1-:
'--
1. Install the output shaft with the adjusting 6. Fit the dial gauge holder with the dial gauge
shims "S3"and "S4". so that a right angle is produced between
the dial gauge axis and the lever.
2. Insert the differential, fit the cover and tighten
all fastening screws with the stipulated
tighteningtorque.
cardiagn.com
tool VW521/12 into the differential and clamp
it securely.
Note Example:
If the friction coefficient of the output shaft is
too lowJthe special tool 3177 must be fitted so 1 st measurement 0.84 mm
that an exact circumferential backlashcan be 2nd measurement 0.85 mm
measured. 3rd measurement 0.84 mm
The differential can then only be inserted in such 4th measurement + 0.83 mm
a way that the aperture of the bevel gears faces Total 3.36 mm
the output shaft.
Average circumferentialbacklash:
3.36 : 4 = 0.84 mm
S2 = Stat.
-Average circumferentialbacklash
cardiagn.com
+ Take-off(constant value)
Take-off= 0.15 mm
Example:
Stat. 1.92 mm
Average circumferential
8. Repeatthe measuring procedure another backlash 0.84 mm
three times after continuingto turn the crown 1.08 mm
whee!through 900 in each case. Add up the Take-off(constantvalue) + 0.15 mm
measured values and calculate the average S2 1.23 mm
circumferentialbacklash.
Withthe assembled special tool 3177, install Note
the differential offset by 1800 and repeat the Discs of 0.45 mm...I.OO mm thickness
measuringprocedure. are available(0.05 mm increments).
Different tolerances allowthe required disc
Note
thicknessto be measuredexactly.
If the individualmeasured values deviate from
each other by more than 0.06 mm during this
measurement,installation of the crown wheel
or the drive set itself is not in order.
Inspectthe assemblywork and replace the
drive set if necessary.
Example:
Stat. 1.92 mm
S2 1.23 mm
S1 0.69 mm
Note
Discs of 0.45 mm...I.OO mm thickness are avail-
able (0.05 mm increments).
Different tolerances allowthe required disc thick-
ness to be measuredexactly.
cardiagn.com
12. Install determinedadjusting shims uSl" on
the crown wheel side and uS2"opposite the
crown wheel.
Note
Theindividualmeasurement resultsmay
deviatefrom eachother by max.0.05 mm.
-~,~~~ -5
cardiagn.com
Group 3
Transmission, manual transmission
Trbl86S.chp
Boxster S Table of Contents
3 Transmission
3 Technicaldata 3-101
35 50 19 Removing
and installingsealingring for inputshaft. . 35-101
cardiagn.com
I
39 22 19 I
Removing
andinstallingsealingring for halfshaftflange. . 39-101
cardiagn.com
34350002
8
3 Technical data (Boxster 5) 3 -101
Printed in Germany -33, 1999 8653_101
Boxster Transmission 3
3 Technical'data (Boxster 5)
cardiagn.com
34350005
1 000410
T
Transmission type
T
Index for version
I
Serial number
within transmission number
= normal differential
cardiagn.com
t
Drive haft on transmission
flange MIa 81 (60)
Clutchlslave cylinder on
transn)ission M8 23 (17)
cardiagn.com
Guide~ubefor release
bearin~ on transmission M8 24 (18)
MI2 85 (63)
Trans~iSSion
on en~ine MID 45 (33)
Rever~inglight switch
on tra~smission M12 15(11.0)
Brack~tfor shift cables on
trans~ission MIa 45 (33)
Tools
cardiagn.com
34350004
Removal I
34350006
cardiagn.com
8. Removedrive shafts at the transmissionand
protect the shafts againstdamage (use scrap
pieces of hose with a diameter of 30 mm).
4. Remove~tabilizer.
Warning!
5. Removerear muffler
(see servo No. 26 33 19).
& The clutch pedal must not be
pressed if the slave cylinder has
been removed.
6. Remover~ar cross member (V strut) Danger of injury from flying
piston rod.
7. Remove~eatshield.
> Affix a warning note where it can
be seen in the vehicle!
C apter 2.4, No. 21). 14. Removetransmission support with left and
right hydraulic mounts.
Note
"'"
cardiagn.com
34120001
34120002
Note
The shiftandcablesmustnotbe excessively
bent~r kinked.
~ft
~
Manual transmission -Actuation, ass. housing Boxster
cardiagn.com
34350003
3. Carefullymove transmissionin and properly 4. Fit the clutch slave cylinder and tighten
fas~ento engine. fastening screw to 23 Nm (17 ftlb.).
Note
5. Bleedthe clutchsystem.
Diagonalbrace on
cardiagn.com
carrier side section
and body (MID) = 65 Nm (48 ftlb.]
Stabilizer mounton
stabilizer (M1 0) = 46 Nm (34 ftlb.)
Transmissionsupport on
transmission(M12) = 85 Nm (63 ftlb.
Hydraulicmount on carrier
side section (MB)= 23 Nm(17 ftlb.J
\8
34 49 19 Removing and installing cap for selector force mechanism -Boxster S
Tools
cardiagn.com
500_98
34 49 19 Removing and installing cap for selector force mechanism -Boxster S 34 -107
.
Printed in Germany -33, 1999 86534107
Manual transmission -Actuation, ass. housing Boxster
cardiagn.com
075_98
A -Closure Icap
34 -108 3449 19 Removing and installing cap for selector force mechanism -Boxster S
86534107 Printed in Germany -33, 1999
Boxster Manual transmission -Actuation, ass. housing
Removal
1. Relmovetransmission,
cardiagn.com
484_98
Installation
1. Insertclosure cap and snap ring into the
housingbore.
4. Installtransmission.
34 49 19 Removing and installing cap for selector force mechanism -Boxster S 34 -109
Printed in Germanv -33. 1999 86534107
Boxster Manual transmission -Gears, shafts, into gearsh.
cardiagn.com
c
117_97
.
35 50 19 Removing and installing sealing ring for input shaft -Boxster S 35 -101
Printed in Germany -35, 1999 86S35101
Manual transmission -Gears, shafts, into gearsh. Boxster
Removal
3. Removeguidetubefor releasebearing (
Ir~\
cardiagn.com
139_1_97
Note
139_97
8
35 -102 35 50 19 Removing and installing sealing ring for input shaft -Boxster S
86S35101 Printed in Germany -35, 1999
I~
Boxster Manual transmission -Gears, shafts, into gearsh.
Installation
1. Pu$hassemblysleeve9255 ontothe toothing 3. Drive in sealing ring with special tool 9628 as
of ,he inputshaft. far as the mounting face.
~\ ~F--
? \d
cardiagn.com
141_97 142_97
2. Fill the space betweenthe dust and sealing 4. Install guide tube for release bearing.
lips on the sealing ring with grease (e.g. Liqui - Always renewfastening screws and tighten
Moly). with 24 Nm (18 ftlb.)
5. Fitreleaseleverwith releasebearing.
35 50 19 Removing and installing sealing ring for input shaft -Boxster S 35 -103
Printed in Germany -35, 1999 86S35101
~-
~
Boxster Final drive -Differential, differential lock
Tools
cardiagn.com
B
c
128;.97
39 22 19 Removing and installing sealing ring for halfshaft flange -Boxster S 39 -101
Printed in Germany -33, 1999 86539101
Final drive -Differential, differential lock Boxster
cardiagn.com
1 -Halfshaft flange 116_97.
2 -Snap ring
3 -Sealing ring
Boxster Final drive -Differential, differential lock
Note
Removal
cardiagn.com
135_97
134_97
Note
Pullout left halfshaftflange by screwing in the
hexagcpn-head bolts "A" on alternate sides. The
bolts ~ust be supported on the rib reinforce-
mentsIof the cover (see Figure).
39 22 19 Removing and installing sealing ring for halfshaft flange -Boxster S 39 -103
Printed in Germany -33, 1999 86539101
Final drive -Differential, differential lock Boxster
Installation
1. Fill the space between the dust and sealing 3. Greasethe snap ring well and drive in the half-
lips with grease (e.g. Liqui -Moly) and drive in shaft flange using the special tools P254 and
the sealing ring up to the mountingface using 9247/1.
special to!ol9252.
cardiagn.com
'- ~~~
/
\.\ 136_97
/K~
A -New snap ring 175_97
3!~ -104 39 22 19 Removing and installing sealing ring for halfshaft flange -Boxster S
86539101 Printed in Germany -33, 1999