aillilis
AALBORG
INDUSTR
ITIONER, SIPART PS2 6DR5000
Crete
part-turn actuators for counter clockwise operation direction. In this case the
parameters “7.SDIR” and 38." YDIR” should be set to “FALL”.
-
Parameter list yw
‘Menu line Function Parameter values Unit | Factory setting Se
Tum (parka actuator)
WAY (linear actuator)
LIWAY (linear actuator
: oes without sine correction) ee
acta | veer nen _ncSt (part-turn actuator:
with NCS)
-neSt (partum actuator
with NCS, inverted)
| Rated anale of rotation for feedback 30°
2.YAGL” 33° >
IL” | (anust correspond to gear ratio) 33° eee, =
Stroke range (optional setting) OFF.
When used, the value must correspond with pad c
these of the th (Phot lever 339.
a:ywaye | theset ofthe leverage ratio on the actuator eis a On
Driver pin must be set tothe value ofthe |...(@horlever 909).
actuator travel or, if this value is not scaled, 40,50.60. 10.
‘to the next lager scale value 90,110,130
(long lever 90°)
INITA | Tniiatition axtomatialip oini/no HAT Se 7 Z
SINITM | Titallsstion (manually) 207A Si as €
Died mA OMA 2
6SCUR | Cunentrange of setpoint 91020 A pus 4MA
et point direction ag) Fae
7spiR | Setpoint di jcate ane SE E
‘ESPRA | Sei point for san oF split ange Dw 1000) % 0 355)
9'SPRE | Set point for end of slit ran 0.010 1000 %. 00 r
A
10-TSUP_| Setpoint amp up pe : Q
TLTSDO— Setpoint amp dows 10400 7 7 =
Set point function
Linear Lin
12sFcr Equal percentage 1:25, 1:33, 1350] 1-25 1-33, 1-50 Lin i
Inverse equal-percentage 1:25, 1:33, 1:50 | nl-25, n1-33 ,n1-S0 s
Frcly adjustable FEE,
TESIO™ | Setpoint taming point at 0%
Mast 3%
to we 0.001000 %
328119 95%
338120 100%
Auto
34.DEBA_| Dead zone of controller a
SEA | Stan of manipulated variable imiting 0.010 1000
36.YE | End of manipulated variable iting 0.010 1000
Standardisation of POS:
37-YNRM | manipulated variable FLOW
Direction of manipulated % SE
38.YDIR | variable for display Falling, FALL
Without
‘Tight closing with “Top only
39-YCLS | manipulated variable Bottom only.INDUSTRIES
AALBORG
&
Parameter list continued
‘Customer
Menu tine Function Parameter values | Unit | Factory setting | Cosveme
40,YCDO_| Value for ight losing, bottom 0.010 100.0 % 03 Gr
SSLYCUP _| Value for tight clsing, top 0.010 100.0 % WS
Function of BI I:
None OFF i
‘Only message (NO/NC contact aon
1 | Block configuring (NO contact) Loe orF
“2BINI® | Block configuring and manual (NO contact) bLoe2
Drive valve to pos. up (NOINC contact) uP /-uP
Drive valve to pox down (NO/NC contact) | doWn/-doWn
Block movement (NOINC contact) StoP /- StoP
Function of BI 2:
; e@ None OFF =
10. | Only message (NOMNC contact) on /-on OFF
. “S.BIN2® | Drive valve to pos. up (NOINC contat) AP uP
Drive valve to pos. down (NOINC contact) | doWn/-doWn
Block movement (NO/NC contact) StoP /-StoP
Without oFF
44.4FCT® | Alarm function ae OFF ere
AAlemax. A2=max. NA|NA
@SAi__| Response threshold oF alarm | D016 1000 % TOO. o
46.A2 | Response threshold of alarm 2 0.010 1000 % 90.0, ZS
Function of alarm output
cw | oui ae
47.4FCT® | Fault+ not automatic y 4 L
Fault + not automatic + BI nab \
('P" means logical OR operation)
‘Monitoring time for faut message Auto
48.5TIM_| contol deviation” 010 100, i
Response threshold for full message “Auto ala
49-4LIM | «control deviation” 0.00 100.0 ay
'50.STRK | Limit for stroke integral oe
1 to 1.0089
oe OFF
S1.4DCHG | Limit for direction change ie
OFF
52.1, ZERO | Limit for end stop monitoring, bottom woe
OFF
53. OPEN | Limit for end stop monitoring, top oo Sa
3 aa OFF
'54.1,DEBA | Limit for dead zone monitoring Pe
Preset (story sting) FS
‘no nothing activated 1
‘Str start of factory setting afer pressing |
SS.PRST. | key for5 see, sa
“OCAY” display following successful
factory setting ¥
“CAUTION: preset results in “NO INIT"
Tif tum i seleted its not possible to set 33 ; 3
ap ue if 1.YFCT = tur has been
> ts only appear with selection 12.SFCT = FrE
a tialisation has not yet been carrie
st evil