Professional Documents
Culture Documents
Mark 50 Series
This brochure includes the following Series: • Sliding Gate Trim — unique seat design for un-
surpassed trim life and accuracy.
• MK50: a line of self-operating back pressure reg- • Jorcote Seat Coating — ceramic composite for
ulators designed with Jordan Valve’s sliding gate liquids, gases and especially steam. Very low
seats. friction with outstanding wear resistance and a
• MK51: The MK51 features a larger diaphragm temperature rating of up to 550°F (288°C). Steam
than a standard MK50 to provide even greater tested to 1,000,000 cycles and still maintained
sensitivity and more accurate regulation of your Class IV leakage.
required setpoint. • Jorlon Diaphragm — extremely durable, virtually
• MK50QC: The MK50QC features a “Quick universally applicable up to 450°F. Tested without
Change” dome for simple range spring replace- failure to over 1,000,000 full stroke cycles. Ideal
ments. Ideal for facilities with multiple back pres- for steam, gases and liquids. 316SST diaphragm
sure requirements as it is possible to stock one applicable up to 550°F.
valve with several spare springs to cover a wide • Straight-through Flow — The flow is straight
range of needs. through the valve seats and body. Direction of the
• MK50H: The MK50H features a handwheel that disc travel is perpendicular to the flow, not op-
is mounted on the adjusting screw to allow easy posed to the direction of the flow. Thus, the flow
setpoint changes. does not unbalance the seats. The MK50 can use
• MK50HP: The MK50HP option is an elongated a wider range of its stroke to give accurate con-
spring housing that features a large spring for trol; less offset and rangeability up to 20:1.
high pressure setpoints up to 450 psi (31,03 • Quiet Operation — typically 5-10 dB less than
bar). conventional globe style regulators. The disc
• MK50GP: The MK50GP option is used in grain and plate are always in contact, which eliminates
processing for starch cookers and other viscous chattering. Straight-through flow minimizes turbu-
services. lence. Multiple orifices in the plate and disc divide
• MK50CR: The MK50CR option has a special the flow stream into smaller flow components.
spring housing for use if the valve is in cryogenic • Minimum Maintenance — The MK50 sliding
services. gate seats require no special tools for disassem-
• MK501/502: The MK501 and MK502 meet higher bly. The seats are pre-lapped at the factory and
capacity requirements than standard back pres- are self-lapping while in operation ensuring a
sure regulators. continual tight shutoff.
Mark 50 Series
Ideal for gas and liquids
Superior for steam
Internal sensing
simplifies installation,
Jorlon diaphragm - proprietary
improves response
modified PTFE excellent for high
time
cycling, chemical resistance,
steam service
Sliding Gate Trim -
reduce or replace
Straight through flow:
trim with ease
less noise, less wear,
better rangeability,
longer seat life
-2-
Mark 50 Self-Operating Back Pressure Regulators
Specifications — MK50/50QC/51/50HP
Sizes: (1/4" & 3/8" sizes use 1/2" body with reducers) Seat Materials:
• Mark 50: 1/4" through 4" (DN8 through DN100) • Jorcote on SST — Standard
• Mark 50QC: 1/4" through 2" (DN8 through DN50) • Other materials available — Consult factory
• Mark 51: 1/4" through 3/4" (DN8 through DN20)
• Mark 50HP: 1/2" through 4" (DN15 through DN100) Diaphragm Materials:
• Jorlon - Standard
End Connections: • Stainless Steel - Standard
• Threaded – FNPT, BSPT, BSPP (1/4” – 2” only, DN8- • Buna-N - Standard
DN50) • Viton - Optional
• ANSI Flanges (150#, 300#, 600#)
• DIN Flanges (PN10/16, PN25/40) Service: Steam, water, oil, gas, air and chemicals
• JIS Flanges (upon request)
Shutoff: ANSI Class IV
Spring Housing:
• Ductile Iron — 1/4" - 2" (DN8 - DN50) Options:
• Ductile Iron — 2-1/2" - 4" (DN65 - DN100) • Double Bolting: improves the pressure rating of
Body Materials: the valve and ensures a tight seal between the
• Ductile Iron spring housing and the body for services with high
• Bronze (1/2" - 2", DN15-DN50) inlet pressures.
• Cast Iron (2-1/2" - 4", DN65-DN100) • High Pressure Spring Housing: the HP option
• Carbon Steel (A216 WCB) is an elongated spring housing that features a
• Stainless Steel (A351/CF8M) large spring for high pressure setpoints (up to 450
psi/31bar).
Trim Materials: • Handwheel: the H option is a handwheel that is
• 303SST — Standard on Ductile Iron, Bronze, mounted on the adjusting screw to allow for easy
Carbon Steel valves setpoint changes.
• 316SST — Standard on Stainless Steel valves • Exotic Alloys: where service conditions dictate the
• Monel, Hastelloy and other Alloys available use of specialty materials, the Mark 50 Series can
be produced with bodies, trim and seats in Monel,
Pressure Control Ranges: Select a range to match Alloy 20, Hastelloy B, Hastelloy C, Titanium and
your setpoint. For optimal performance, your setpoint others.
should fall in the upper portion of the selected range. • GP Option: grain processing modification for
Spring Ranges
starch cookers and other viscous services.
Model Size (DN • Cryogenic Service: CR option is a special spring
PSI BAR
housing for use if valve is in cryogenic conditions.
2 - 20 0,14 - 1,38
10 - 30 0,69 - 2,07 Cv Values & Maximum Differential Pressures
1/4" - 3/4"
20 - 45 1,38 - 3,10 Cv (Kv) Size (DN) Seat Material Max. ∆P PSI (bar)
(DN8 - DN20)
30 - 135 2,07 - 9,31 0.84 (0,74) 1/4" (DN8) Jorcote 500 (34)
80 - 185 5,52 - 12,76
1.6 (1,4) 3/8" (DN12) Jorcote 500 (34)
1/2 - 4 0,03 - 0,28
2-6 0,14 - 0,41 2.5 (2,2) 1/2" & 3/4"
50 & 50QC Jorcote 450 (31)
1" - 2" 4 - 13 0,28 - 0,90 4.4 (3,8) (DN15 & DN20)
(DN25 - DN50) 8 - 20 0,55 - 1,38 6.4 (5,5) 1" & 1-1/4"
Jorcote 450 (31)
15 - 80 1,03 - 5,52 9.5 (8,2) (DN25 & DN32)
45 - 150 3,10 - 10,34 15 (12,9) 1-1/2" (DN40) Jorcote 450 (31)
4 - 15 0,28 - 1,03 25 (21,5)
2-1/2" - 4"
7 - 24 0,48 - 1,65 2" (DN50) Jorcote 450 (31)
(DN65- DN100) 30 (25,8)
16 - 30 1,10 - 2,07
55 (47,3) 2-1/2" (DN65) Jorcote 150 (10)
75 - 190 5,17 - 13,10
1/2" - 2" 115 (99) 3" (DN75) Jorcote 150 (10)
100 - 320 6,89 - 22,06
(DN15 - DN40) 200 (172) 4" (DN100) Jorcote 150 (10)
50HP 150 - 450 10,34 - 31,02
2-1/2" - 4" 25 - 50 1,72 - 3,45
(DN65 - DN100) 40 - 130 2,76 - 8,96 Low Flow Cv’s: reduced Cv’s (Kv’s) are available. Cv
1/2 - 5 0,03 - 0,34 (Kv) ratings of smaller valves can be supplied in larger-
2 - 10 0,14 - 0,69 sized valves.
2 - 20 0,14 - 1,38 0.42 (0,36) 0.21 (0,18) 0.08 (0,07) 0.04 (0,03) 0.02 (0,02)
10 - 30 0,69 - 2,07
1/4" - 3/4" 0.008 0.004 0.002
51 20 - 50 1,38 - 3,45 0.0008 (0,0007)
(DN8 - DN20) (0,007) (0,003) (0,002)
20 - 70 1,38 - 4,83
40 - 105 2,76 - 7,24
25 - 150 1,72 - 10,34
30 - 170 2,07 - 11,72
-4-
Mark 50 Self-Operating Back Pressure Regulators
Notes:
1. Double bolting option is required to reach pressures indicated in parentheses ( ).
2. If weld flanges are supplied, use ratings in "TE" column or flange rating, whichever is less (i.e. ANSI 600/900 flanges or PN64/100 flanges).
3. Consult factory for maximum working pressure on 2-1/2" - 4" (DN65 - DN100) Mark 50HP Series
-5-
Mark 50 Self-Operating Back Pressure Regulators
Dimensions — MK50/MK50QC
B
9.00 MAX
Reducer
Bushing
A 1.69
A1 4.50
• Mark 50 / Mark 50QC*: Threaded & FSW Ends • Mark 50 / Mark 50QC*: Threaded & FSW Ends, Metric
Dimensions (inches) Weight Dimensions Wgt.
Size Mat'l Size Mat'l
A B B~QC C D (lbs.) A B B~QC C D (kg)
1/2" & DI/BRZ 3.62 8.50 10.25 1.69 5.12 10 DN15 DI/BRZ 91,95 215,90 260,35 42,93 130,05 4,5
3/4" CS/SS 3.62 8.50 10.25 1.69 5.12 12 & 20 CS/SS 91,95 215,90 260,35 42,93 130,05 5,4
DI/BRZ 4.12 10.00 11.37 2.62 7.09 21 DI/BRZ 104,65 254,00 288,80 66,55 180,09 9,5
1" DN25
CS/SS 4.18 10.75 12.00 2.63 7.09 25 CS/SS 106,17 273,05 304,80 66,55 180,09 11,3
1-1/4" DI/BRZ 4.12 10.00 11.37 2.62 7.09 21 DN32 DI/BRZ 104,65 254,00 288,80 66,55 180,09 9,5
DI/BRZ 4.50 10.25 11.37 2.31 7.09 23 DI/BRZ 114,30 260,35 288,80 58,67 180,09 10,4
1-1/2" DN40
CS/SS 4.81 11.00 12.25 2.25 7.09 31 CS/SS 122,17 279,40 311,15 57,15 180,09 14,1
DI/BRZ 4.50 10.25 11.37 2.75 7.09 26 DI/BRZ 114,30 260,35 288,80 69,85 180,09 11,8
2" DN50
CS/SS 5.50 11.00 12.25 2.75 7.09 35 CS/SS 139,70 279,40 311,15 69,85 180,09 15,9
* For MK50QC, use column B~QC. * For MK50QC, use column B~QC.
-6-
Mark 50 Self-Operating Back Pressure Regulators
Dimensions — MK50
D
A
A1
Dimensions — MK50
A
A1
• Mark 50: Flanged Ends, ANSI • Mark 50: Flanged Ends, Metric
Dimensions (inches) Weight Dimensions (mm)
Weight (kg)
ANSI A1 B C D (lbs.) Size Flange A1 B C D
Size
Flange DN PN
DI/ CS/ DI/ CS/ DI/ CS/ DI/ CS/ DI/ CS/ DI/ CS/
All All All All
BRZ SS BRZ SS BRZ SS BRZ SS BRZ SS BRZ SS
150# 7.25 7.25 8.50 8.50 1.69 5.12 13 15 10/16 184 130 216 240 43 130 5,9 6,8
1/2" 15
300# 7.50 7.50 8.50 8.50 1.69 5.12 14 16 25/40 184 130 216 240 43 130 6,4 7,3
150# 7.25 7.25 8.50 8.50 1.69 5.12 14 16 10/16 184 150 216 240 43 130 6,4 7,3
3/4" 20
300# 7.62 7.62 8.50 8.50 1.69 5.12 16 17 25/40 184 150 216 240 43 130 7,3 7,7
150# 7.25 7.25 10.0 10.75 2.62 7.09 26 34 10/16 184 160 273 262 67 180 11,8 15,4
1" 25
300# 8.751 7.752 10.00 10.75 2.62 7.09 28 37 25/40 184 160 273 262 67 180 12,7 16,8
150# 7.87 — 10.00 — 2.62 7.09 31 — 10/16 200 — 273 — 67 180 12,7 —
1¼" 32
300# 8.37 — 10.00 — 2.62 7.09 31 — 25/40 200 — 273 — 67 180 4,1 —
150# 8.75 8.75 10.25 11.22 2.31 7.09 42 46 10/16 222 200 279 285 59 180 19,1 20,9
1½" 40
300# 10.251 9.252 10.25 11.22 2.31 7.09 45 52 25/40 222 200 279 285 59 180 20,4 23,6
150# 10.00 10.00 10.25 11.42 2.75 7.09 46 50 10/16 254 230 279 290 70 180 20,9 22,7
2" 50
300# 10.50 10.50 10.25 11.42 2.75 7.09 49 55 25/40 254 230 279 290 70 180 22,2 24,9
Flanged Ends CS/SS Flanged Ends CS/SS
Weight Weight
Larger Sizes A B C D Larger Sizes A B C D
(lbs.) (kg)
125-150# 10.88 18.75 6.95 12.75 165 10/16 287 476 177 324 75
2-1/2" 65
250-300# 11.50 18.75 6.95 12.75 165 25/40 293 476 177 324 75
125-150# 11.75 18.75 6.95 12.75 185 10/16 313 476 177 324 84
3" 80
250-300# 12.50 18.75 6.95 12.75 185 25/40 313 476 177 324 84
125-150# 13.88 19.95 8.00 12.75 215 10/16 353 507 203 324 98
4" 100
250-300# 14.50 19.95 8.00 12.75 215 25/40 353 507 203 324 98
1. Not ANSI Standard. 1. Smaller sizes A1 not IFE and not per DIN 3202.
2. IFE only. 2. Larger sizes A not per DIN 3202.
-8-
Mark 50HP Self-Operating Back Pressure Regulators
Dimensions — MK50HP
-9-
Mark 51 Self-Operating Back Pressure Regulators
Dimensions — MK51
A
A1
• Mark 51: Threaded & FSW Ends • Mark 51, Flanged Ends
Dimensions (inches) Weight Dimensions (inches) Weight
Size Material
A B C D (lbs.) ANSI A1 B C D (lbs.)
Size
Flange
1/2" & DI/BRZ 3.62 10.25 2.25 7.12 12 DI/ CS/ DI/ CS/ DI/ CS/
All All
3/4" BRZ SS BRZ SS BRZ SS
CS/SS 3.62 10.25 2.25 7.12 13
1/2" & 150# 9.62 9.62 10.25 10.25 2.25 7.12 26 26
3/4" 300# 10.25 10.25 10.25 10.25 2.25 7.12 29 29
-10-
Mark 50 Self-Operating Back Pressure Regulators
Ordering Schematic
1 2 3 4 5 6 7 8 9 10
— — /
1 Model 5 Trim
50 Standard S3 303SS I3 303SSF/IFE (1" - 2")
50HP High Pressure S6 316SS I6 316SSF/IFE (1" - 2")
50QC Quick Change
6 Seat Material
51 Large Diaphragm
A 303SST (1/4" - 2") V 303SS/Jorcote
Size B 316SST (1/4" - 2") W 316SS/Jorcote
2 303SST/Teflon
Inches (DN) Inches (DN) Q R 316SST/Teflon Coated
Coated
025 1/4" (DN8) 150 1-1/2" (DN40)
038 3/8" (DN10) 200 2" (DN50) 7 Cv (Kv)
050 1/2" (DN15) 250 2-1/2" (DN65) (MK50/50HP only) 1 0.21 (0,28) 9 15 (12,93)
075 3/4" (DN20) 300 3" (DN80) (MK50/50HP only) 2 0.42 (0,36) A 25 (21,55)
100 1" (DN25) 400 4" (DN100) (MK50/50HP only) 3 0.84 (0,72) B 30 (25,86)
SW FSW
8 MK50HP Spring Range PSI (BAR)
F1 125#FE (Except IFE)
1/2" - 2" 2-1/2" - 4"
I5 150# IFE
A1 75-190 (5,17-13,10) 64 25-50 (1,72-3,45)
F5 150# FE (except IFE)
A7 100-320 (6,89-22,06) 82 40-130 (2,76-8,96)
F2 250# FE (except IFE)
A9 150-450 (10,34-31,02)
I3 300# IFE
F3 300# FE (except IFE) 8 MK51 Spring Range PSI (BAR)
I7 PN 10 DIN IFE (CS/S6) 04 1/2-5 (0,03-0,34)* 62 20-70 (1,38-4,83)
I6 PN 16 DIN IFE (CS/S6) 08 2-10 (0,14-0,69) 86 40-105 (2,76-7,24)
I8 PN 25 DIN IFE (CS/S6) 14 2-20 (0,14-1,38) 69 25-150 (1,72-10,34)
I4 PN 40 DIN IFE (CS/S6) 34 10-30 (0,69-2,07) 79 30-170 (2,07-11,72)
MK50, 2-1/2" - 4" 54 20-50 (1,38-3,45)
I1 125# IFE * Must use elastomer diaphragm
-12-
Mark 501/502 High Flow Back Pressure Regulators
Dimensions — MK501/502
A
A1
• Mark 501/502: Threaded & FSW Ends • Mark 501/502, Flanged Ends
Dimensions (inches) Weight Dimensions (inches) Weight
Size Material
A B C D (lbs.) ANSI A1 B C D (lbs.)
Size
Flange
1-1/2" DI/BRZ 4.50 10.25 2.75 7.09 26 DI/ DI/ CS/ DI/ CS/
CS/SS All All
- 2" BRZ BRZ SS BRZ SS
CS/SS 5.50 11.00 2.75 7.09 35
150# 10.00* 10.00* 10.25 11.22 2.31 7.09 42 46
1-1/2"*
300# 10.25* 10.25* 10.25 11.22 2.31 7.09 45 52
• Mark 501/502: Threaded & FSW Ends, 150# 10.00 10.00 10.25 11.42 2.75 7.09 46 50
2"
Metric 300# 10.50 10.50 10.25 11.42 2.75 7.09 49 55
Dimensions (mm) * Not IFE. Not ANSI Standard.
Size Weight
Material
(DN) A B C D (kg)
DI/BRZ 114 260 70 180 11,8
40 - 50
CS/SS 140 279 70 180 15,9 • Mark 501/502, Flanged Ends, Metric
Dimensions (mm)
Weight (kg)
Size Flange A1 B C D
(DN) PN
DI/ CS/ DI/ CS/ DI/ CS/
All All
BRZ SS BRZ SS BRZ SS
10/16 254 254 279 285 58,7 180 19,1 20,9
40
25/40 260 260 279 285 58,7 180 20,4 23,6
10/16 254 230 279 290 69,9 180 20,9 22,7
50
25/40 267 230 279 290 69,9 180 22,2 24,9
-13 -
MK50/0521
Mark 501/502 High Flow Back Pressure Regulators
Ordering Schematic
1 2 3 4 5 6 7 8 9 10 11 12
— — /
Size W 316SS/Jorcote
2
Inches (DN)
150 1-1/2" (DN40) 7 Cv (Kv)
200 2" (DN50) A 25 (22)
B 30 (26)
BR Bronze C 50 (43)