Professional Documents
Culture Documents
OWNER'S MANUAL
WARNING:
FEATURES:
p ER SOURCE:
POWER INDICATOR
REAR CONTROLS
•
- .-
..
AC CORD WITH PLUG H-CENTER
(HORIZONTAL CENTER )
1. Connect the signal cable from your monitor to the TTL l/P (9 PIN "D"
2. Connect the power cord with specified outlet, and pull the PULL ON switch
to set the unit on. It will be a few seconds before the picture comes on
to the screen.
4. To adjust the picture to the center of the screen, use H-CENTER for
CAUTIONS:
1. Do not use or store this monitor in a place with much moisture or dust,
2. Do not cover the ventilation slits while in operation. This will prevent the
necessary ventilation.
3. When the screen surface filter develops dusts, clean with soft cloth
moistened with water. Special cleaning cloth is also available from your
local dealer.
4. When the monitor is not in use for a long time, be sure to pull the power
5 1. GND 6. Intensity
2. Shield GND 7. Video
3. l 8. H. Sync
1 4. r Not used 9. V. Sync
5.
MODEL: VIDE0-310/VIDE0-310A
PWB-1695-B R111 CRITICAL COMPONENT WARNING
s+12v 6.8(1/2W)
These critical components that are marked with a&_ on the schematic diagram
K9
B+ and the parts list are used to prevent shock, fire hazard and excessive
12V R108 X-radiation. All these special components must be replaced only with the same
lOK
R604 type identical to those in the schematic diagram and parts list.
ZD601 3.3K
EQAOl (1/2
C102 NOTE.
J!i6S Lt_ 10/ 1. All resistor values are in ohms, K = 1000, M = 1000000.
16V
Unspecified Carbon film, ±5% Y.W
(M) Carbon Solid,J: ±5%,unspecified: ±10%
(MFR) Metal film,±5%
JSV (CT) Cement wire-wound,±5%
2. All Capacitors are in µ,F. P represents pF
R610
NOTE 0602 Q603 820 Unspecified Ceramic,+80 3 (NP) Elyc. Non-polar, ±10";6
Q102
.J, Hot Chassis Ground
2SA673C 2 SC458
&. 2SC1213C. -20 (-ij±) Elyc. < 4.7µ,F +715 °
0%,others +510%
,& Cold Chassis Ground
Tantal. ±20"..b
-
3. This circuit diagram is original one. therefore there may be a slight difference
lOK 1K 22K 100/16V 470/ ZOKB 150 470 C421 from your set.
25V
s815~
V-SIZE 4. All marked voltage are taken under 3.5VP-P Video Input
C307 + D301 3.8VP-P Vertical Input
C503 47/10 3.6VP-P Horizontal Input
S4 .082(0) IN4148
V. DRIVE 0301
(ML) 2 SC458C
~01
.01
D501
IN4148
(2SC945Q) I
SR310
>47K
D302
(ML) C304 IN414
R304 22/16V (EU)
0501 12K + :1
I
(DTL) >8.2K
INPUT
C104
S2 O DUAL INTENSITY +c305 R319 .01 /
E1 O !ill.Ql.L.tjQ 22/10V lKB 500
E2 O GROUND
R305
(DTL) V-LIN
RmfiTHJrn
4 7K;, 5KD5
0.74V
C417 R418
S3 0 H-DRIVE
1.2
(l/2W)
R318
100 'J 150P 100
M ~ LI LI
T402
9+ SR404
9(G) (SU) RGP-lOM
12V 0403 ~----,
R703 0901 2SC681AYL
10K8
CENTER ZD901 2sC458C ® (2SC1617) SR402
RGP-
VR
13E82 R901
(2SC9450 l
I 19.5V 10G
820 I
r @
R413
56 (02.4VP-P(V) @11VP-P(V) @3.6VP-P(H) CZ) 3.4 VP-P (H)
R902 C901 C413
m JUl u
lOK 082
t 5V
(MLI
J .01
PF/630V
&. +
R42
2M8
C705 R705 FOCU
10.7V C411 51_ - - - - - -
47/10V 82 +c410 +C420
+ L402 4 70/25V 470/25V
22/160V
CJ/" D701
8+
12V
27uH
IN4148 0402
2SC1213C @1 SVP-P (H) @)180VP-P(H) @570VP-P(H)
PWB-1532-A07
47 SCHEME-DIA-1336F