Professional Documents
Culture Documents
K ELECTRICAL
SECTION
LIGHTING SYSTEM
LT B
E
CONTENTS
PRECAUTIONS .......................................................... 4 Disassembly and Assembly .................................... 15 F
Precautions for Supplemental Restraint System Bulb Replacement .................................................. 15
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN- HEADLAMP HIGH/LOW BEAM .......................... 15
SIONER” .................................................................. 4 PARKING LAMP .................................................. 15 G
General Precautions for Service Operations ............ 4 FRONT TURN SIGNAL LAMP ............................ 15
HEADLAMP ................................................................ 5 HEADLAMP AIMING CONTROL ............................. 16
Component Parts Location ....................................... 5 Schematic ............................................................... 16
H
System Description .................................................. 5 Removal and Installation of Headlamp Aiming
LOW BEAM OPERATION ..................................... 5 Switch ..................................................................... 17
HIGH BEAM OPERATION .................................... 5 RELATED OPERATION ...................................... 17
FLASH-TO-PASS OPERATION ............................ 5 Switch Circuit Inspection ........................................ 17 I
COMBINATION SWITCH READING FUNCTION..... 5 FRONT FOG LAMP .................................................. 18
EXTERIOR LAMP BATTERY SAVER CONTROL..... 5 Component Parts Location ..................................... 18
Schematic ................................................................ 6 System Description ................................................. 18 J
Terminals and Reference Values for BCM ............... 7 FRONT FOG LAMP OPERATION ....................... 18
Terminals and Reference Values for IPDM E/R ....... 8 COMBINATION SWITCH READING FUNCTION... 18
CONSULT-II Functions (BCM) ................................. 9 EXTERIOR LAMP BATTERY SAVER CONTROL... 18
LT
CONSULT-II BASIC OPERATION ......................... 9 Schematic ............................................................... 19
WORK SUPPORT ................................................. 9 Terminals and Reference Value for BCM ............... 20
DATA MONITOR ................................................... 9 Terminals and Reference Values for IPDM E/R ...... 20
ACTIVE TEST ..................................................... 10 CONSULT-II Function (BCM) ................................. 21 L
CONSULT-II Functions (IPDM E/R) ....................... 10 CONSULT-II Function (IPDM E/R) ......................... 21
CONSULT-II BASIC OPERATION ....................... 10 Front Fog Lamps Do Not Illuminate (Both Sides) ... 21
DATA MONITOR ................................................. 10 Front Fog Lamp Does Not Illuminate (One Side) ... 21 M
ACTIVE TEST ......................................................11 Front Fog Lamp Indicator Does Not Illuminate ....... 21
Headlamps High Do Not Illuminate (Both Sides) ....11 Front Fog Lamps Do Not Go OFF (Both Sides) ..... 22
Headlamp High Does Not Illuminate (One Side) ....11 Aiming Adjustment .................................................. 22
High Beam Indicator Does Not Illuminate ...............11 Bulb Replacement .................................................. 23
Headlamps Low Do Not Illuminate (Both Sides) ... 12 Removal and Installation ........................................ 23
Headlamp Low Does Not Illuminate (One Side) ... 12 TURN SIGNAL AND HAZARD WARNING LAMPS... 24
Headlamps High Do Not Go OFF (Both Sides) ...... 12 Component Parts Location ..................................... 24
Headlamps Low Do Not Go OFF (Both Sides) ...... 12 System Description ................................................. 24
Aiming Adjustment ................................................. 13 TURN SIGNAL LAMP LEFT OPERATION .......... 24
PREPARATION BEFORE ADJUSTING .............. 13 TURN SIGNAL LAMP RIGHT OPERATION ....... 24
LOW BEAM AND HIGH BEAM ........................... 13 HAZARD WARNING LAMP WARNING OPER-
ADJUSTMENT USING AN ADJUSTMENT ATION .................................................................. 24
SCREEN (LIGHT/DARK BORDERLINE) ............ 14 INTERLOCKED OPERATION REMOTE KEY-
Removal and Installation ........................................ 14 LESS ENTRY SYSTEM ...................................... 24
RELATED OPERATION ...................................... 14 COMBINATION SWITCH READING FUNCTION... 25
Schematic ............................................................... 26
LT
PRECAUTIONS PFP:00011
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER” GKS000F7
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
● To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
● Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
● Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
General Precautions for Service Operations GKS000F8
HEADLAMP PFP:26010
A
Component Parts Location GKS000TA
SKIB7590E
G
● BCM (Body Control Module) controls headlamps low and high operation. H
● IPDM E/R (Intelligent Power Distribution Module Engine Room) operates headlamp bulbs according to
CAN communication signals from BCM.
● Combination meter operates high beam indicator lamp according to CAN communication signals from I
BCM.
LOW BEAM OPERATION
J
When the lighting switch is in 2ND position, BCM detects the HEAD LAMP1 and 2 (ON) by BCM combination
switch reading function. And then, BCM sends low beam request signal (ON) through CAN communication.
When receiving low beam request signal (ON), IPDM E/R turns ON headlamp low relay in IPDM E/R. And
then headlamp bulbs (low) go ON. LT
Schematic GKS000TC
TKWB2970E
A
Ter- Signal Measuring condition
Wire Signal
minal input/ Ignition Reference value
color name Operation or condition
No. output switch B
OFF Approx. 0 V
F
Lighting switch HIGH beam
(Operates only HIGH beam
switch)
G
PKIB4957J
Approx. 1.0 V
OFF Approx. 0 V H
Approx. 2.0 V
Ignition LT
11 L switch Input ACC — Battery voltage
(ACC)
L
M
OFF
Approx. 1.2 V
OFF
Approx. 1.2 V
Ignition
38 O switch Input ON — Battery voltage
(ON)
39 L Input/
CAN − H — — —
Output
40 P Input/
CAN − L — — —
Output
Battery
57 LG power Input OFF — Battery voltage
supply
67 B Ground — ON — Approx. 0 V
Battery
70 Y power Input OFF — Battery voltage
supply
25 B Ground — — — Approx. 0 V
CONSULT-II can display each diagnostic item using the diagnostic test mode shown following.
BCM diagnosis part Diagnosis mode Description D
WORK SUPPORT The setting for each function can be changed.
HEADLAMP DATA MONITOR BCM input data is displayed in real time.
E
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal.
SELF-DIAG RESULTS Refer to BCS-18, "SELF-DIAG RESULTS" .
BCM
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read. F
ACTIVE TEST
Test item Description
TAIL LAMP Tail lamp relay is operated by switching ON-OFF.
HEAD LAMP Headlamp high relay and headlamp low relay is operated by switching ON−OFF.
RR FOG LAMPNOTE —
FR FOG LAMP Front fog lamp relay is operated by switching ON-OFF.
NOTE —
CORNERING LAMP
CONSULT-II can display each diagnostic item using the diagnostic test mode shown following.
Diagnosis Mode Description
SELF-DIAG RESULTS Refer to PG-7, "SELF-DIAG RESULTS" .
DATA MONITOR The input/output data of IPDM E/R is displayed in real time.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST IPDM E/R sends a drive signal to electronic components to check their operation.
Inspection 1 Result Inspection 2 Result Inspection 3 Result Inspection 4 Result Replace or repair F
Check “HI BEAM OK — — Replace BCM.
SW” status on
OK Replace lighting
the BCM data NG — — G
monitor. switch.
Check BCM
OK self-diagnosis Check CAN com-
result. munication. Refer ● Repair harness or H
to LAN-2, "Pre- connector.
Start “EXTER- U1000 — — —
cautions When
NAL LAMPS” Using CONSULT- ● Replace BCM.
on the IPDM E/ II" . I
R active test,
and check if Start “EXTER- Check headlamp Replace headlamp
OK
headlamps NAL LAMPS” on high circuits bulbs.
high illuminate. the IPDM E/R OK between head-
Check head- Repair harness or J
active test, and lamps and NG
lamp high cir- OK connector.
check head- grounds.
NG cuits between lamps high output
IPDM E/R and voltage of IPDM NG — — Replace IPDM E/R. LT
headlamps. E/R.
Repair harness or
NG — — — —
connector.
L
Headlamp High Does Not Illuminate (One Side) GKS001EP
Inspection 1 Result Inspection 2 Result Inspection 3 Result Inspection 4 Result Replace or repair
Check status on OK — — Replace BCM.
the BCM data
monitor:
OK ● “HEAD LAMP Replace lighting
SW 1” NG — —
switch.
Check BCM ● “HEAD LAMP
OK self-diagnosis SW 2”
result.
Start “EXTER- Check CAN com-
NAL LAMPS” on munication. Refer ● Repair harness or
the IPDM E/R to LAN-2, "Pre- connector.
U1000 — — —
active test, and cautions When
Using CONSULT- ● Replace BCM.
check if head-
lamps low illumi- II" .
nate. Start “EXTER- Check head- Replace headlamp
OK
NAL LAMPS” on lamp low circuits bulbs.
Check head- the IPDM E/R OK between head-
OK active test, and lamps and Repair harness or
lamp low cir- NG
check headlamps grounds. connector.
NG cuits between
IPDM E/R and low output volt-
age of IPDM E/R. NG — — Replace IPDM E/R.
headlamps.
Repair harness or
NG — — — —
connector.
PKIC4641E I
PKIC5211E
If the vehicle front body has been repaired and/or the headlamp assembly has been replaced, check aiming.
Use the aiming chart shown in the figure.
● Basic illumination area for adjustment should be within the range shown on the aiming chart.
Adjust headlamp accordingly.
Removal and Installation GKS001CV
PKIC1223E
RELATED OPERATION
Front bumper. Refer to EI-2, "FRONT BUMPER" .
NOTE:
After installation, perform aiming adjustment. Refer to LT-13, "Aiming Adjustment" .
PKIC4642E
Schematic GKS001JP
TKWB2971E
A
● Pawls (A)
● Headlamp aiming switch (1)
B
D
PKIC0914E
RELATED OPERATION
Switch panel assembly. Refer to IP-2, "INSTRUMENT PANEL ASSEMBLY" . E
SKIB3413J I
LT
SKIB7590E
Schematic GKS001CY
LT
TKWB2972E
PKIB4955J
Approx. 0.8 V
Ignition switch
11 L Input ACC — Battery voltage
(ACC)
OFF
PKIB4956J
Approx. 1.0 V
Ignition switch
38 O Input ON — Battery voltage
(ON)
39 L Input/
CAN − H — — —
Output
40 P Input/
CAN − L — — —
Output
Battery power
57 LG Input OFF — Battery voltage
supply
67 B Ground — ON — Approx. 0V
Battery power
70 Y Input OFF — Battery voltage
supply
Front fog lamp Lighting switch must be in Front fog lamp switch: OFF Approx. 0 V
16 V Output ON
LH the 1ST position Front fog lamp switch: ON Battery voltage
Front fog lamp Lighting switch must be in Front fog lamp switch: OFF Approx. 0 V
17 W
RH
Output ON
the 1ST position
B
Front fog lamp switch: ON Battery voltage
25 B Ground — — — Approx. 0 V
Input/ C
26 P CAN − L — — —
Output
Input/
27 L CAN − H — — —
Output
D
CONSULT-II Function (BCM) GKS000U0
Inspection 1 Result Inspection 2 Result Inspection 3 Result Inspection 4 Result Replace or repair
Check “HI BEAM OK — — Replace BCM.
G
SW” status on
OK Replace lighting
the BCM data NG — —
monitor. switch.
H
Check BCM
OK self-diagnosis Check CAN com-
result. munication. Refer ● Repair harness or
Start “EXTER- to LAN-2, "Pre- connector.
U1000 — — — I
NAL LAMPS” cautions When
Using CONSULT- ● Replace BCM.
on the IPDM E/
R active test, II" .
and check if Start “EXTER- Check front fog Replace front fog J
front fog lamps OK
NAL LAMPS” on lamp circuits lamp bulbs.
illuminate. Check front the IPDM E/R OK between front fog
fog lamp cir- OK active test, and lamps and Repair harness or
NG
cuits between check front fog grounds. connector. LT
NG
IPDM E/R and lamp output volt-
front fog age of IPDM E/R. NG — — Replace IPDM E/R.
lamps.
Repair harness or L
NG — — — —
connector.
The front fog lamp is a semi-sealed beam type which uses a replaceable halogen bulb. Before performing
aiming adjustment, make sure of the following.
● Keep all tires inflated to correct pressure.
● Place vehicle on level surface.
● Set that there is no-load in vehicle other than the driver (or equivalent weight placed in driver’s position).
Coolant, engine oil filled up to correct level and full fuel tank.
Adjust aiming in the vertical direction by turning the adjusting screw (A).
PKIC1070E
1. Set the distance between the screen and the center of front fog
lamp lens as shown.
2. Turn front fog lamps ON.
3. Adjust front fog lamps using adjusting screws so that the top
edge of the high intensity zone is in the figure.
When performing adjustment, if necessary, cover the headlamps
and opposite front fog lamp.
PKIC1644E
A
● Front fog lamp connector (1)
● Front fog lamp bulb socket (2)
Front fog lamp : 12V - 35W (H8) B
D
PKIC1071E
SKIB2519J
SKIB7591E
● BCM (Body Control Module) controls turn signal lamps (left and right) and hazard warning lamps opera-
tion.
● Combination meter operates turn signal indicator lamps (left and right) according to CAN communication
signals from BCM.
TURN SIGNAL LAMP LEFT OPERATION
When the lighting switch is in TURN LH position, BCM detects the TURN LH (ON) by BCM combination switch
reading function. BCM outputs the turn signal (left) to turn signal lamps (left) intermittently. And then, turn sig-
nal lamps (left) start flashing operation. BCM sends turn indicator signal (left) through CAN communication.
Combination meter receives turn indicator signal (left) through CAN communication, and make turn signal indi-
cator (left) start flashing operation.
TURN SIGNAL LAMP RIGHT OPERATION
When the lighting switch is in TURN RH position, BCM detects the TURN RH (ON) by BCM combination
switch reading function. BCM outputs the turn signal (right) to turn signal lamps (right) intermittently. And then,
turn signal lamps (right) start flashing operation. BCM sends turn indicator signal (right) through CAN commu-
nication.
Combination meter receives turn indicator signal (right) through CAN communication, and make turn signal
indicator (right) start flashing operation.
HAZARD WARNING LAMP WARNING OPERATION
When the hazard switch is in ON position, BCM detects the hazard switch signal ON. BCM outputs the turn
signal (left and right) to turn signal lamps (left and right) intermittently. And then turn signal lamps (left and
right) start flashing operation. BCM sends turn indicator signal (left and right) through CAN communication.
Combination meter receives turn indicator signal (left and right) through CAN communication, and makes turn
signal indicator (left and right) start flashing operation.
INTERLOCKED OPERATION REMOTE KEYLESS ENTRY SYSTEM
The remote keyless entry system is triggered by input from key fob. When key fob is used to activate remote
keyless entry system, BCM judges that the condition of hazard warning lamps operation meets. Then BCM
outputs the turn signal (left and right) to turn signal lamps (left and right) intermittently. And then turn signal
lamps (left and right) start flashing operation. BCM sends turn indicator signal (left and right) through CAN
communication.
Combination meter receives turn indicator signal (left and right) through the CAN communication makes turn
signal indicator (left and right) start flashing operation.
LT
Schematic GKS000WE
TKWB2973E
A
Ter- Signal Measuring condition
Wire
minal Signal name input/ Ignition Reference value
color Operation or condition
No. output switch B
OFF Approx. 0 V
C
Lighting, turn, wiper
Combination switch
2 BR Input ON
switch input 5 (Wiper intermittent Turn signal switch to right
dial position 4) D
PKIB4957J
Approx. 1.0 V E
OFF Approx. 0 V
F
Lighting, turn, wiper
Combination switch
3 GR Input ON
switch input 4 (Wiper intermittent Turn signal switch to left
dial position 4)
G
PKIB4957J
Approx. 1.0 V H
Ignition switch
11 L Input ACC — Battery voltage
(ACC)
ON Approx. 0 V I
Hazard switch
29 L input OFF Hazard switch
signal OFF Battery voltage
OFF LT
Approx. 1.2 V
Ignition switch
38 O Input ON — Battery voltage
(ON)
39 L Input/
CAN − H — — —
Output
40 P Input/
CAN − L — — —
Output
Battery power
57 LG Input OFF — Battery voltage
supply
Flasher output
60 V Output ON Turn signal switch
(Left) To left
SKIA3009J
OFF Approx. 0 V
Flasher output
61 W Output ON Turn signal switch
(Right) To right
SKIA3009J
67 B Ground — ON — Approx. 0 V
Battery power
70 Y Input OFF — Battery voltage
supply
CONSULT-II can display each diagnostic item using the diagnostic test mode shown following.
BCM diagnosis part Diagnosis mode Description
DATA MONITOR BCM input data is displayed in real time.
FLASHER
ACTIVE TEST Operation of electrical loads can be checked by sending driving signal to them.
ACTIVE TEST
Test item Description
FLASHER Turn signal lamp (right or left) can be operated by ON-OFF operations.
A
Inspection 1 Result Inspection 2 Result Inspection 3 Result Inspection 4 Result Replace or repair
Check “TURN OK — — — — Replace BCM.
SIGNAL R” sta-
OK Replace lighting B
tus on the BCM NG — — — —
data monitor. switch.
Inspection 1 Result Inspection 2 Result Inspection 3 Result Inspection 4 Result Replace or repair F
Check “TURN OK — — — — Replace BCM.
SIGNAL L” sta-
OK Replace lighting
tus on the BCM NG — — — — G
data monitor. switch.
Start “FLASHER” on Check cir- Replace turn sig-
Start “FLASHER” OK
the BCM active test, cuits between nal lamp LH bulbs.
Check turn sig- on the BCM H
and check if turn sig- OK turn signal
nal lamp cir- active test, and
nal lamps LH illumi- OK lamps LH and Repair harness or
cuits between check turn signal NG
nate. NG grounds. connector.
BCM and turn LH output volt-
signal lamps age of BCM. NG — — Replace BCM. I
LH.
Repair harness or
NG — — — —
connector.
J
Hazard Warning Lamps Do Not Operate But Turn Signal Lamps Operate GKS000WK
Inspection 1 Result Inspection 2 Result Inspection 3 Result Inspection 4 Result Replace or repair
OK — — — — — — Replace BCM. LT
OK — — — — Replace BCM.
Check hazard switch Repair connector
L
Check “HAZ- signal circuits: OK for connection,
ARD SW” status Check hazard bend and loose fit.
● between hazard
on the BCM data switch signal out- OK
NG Check haz- switch and ground
monitor. put voltage of NG Repair harness or
ard switch between BCM and NG M
BCM. ●
connector.
hazard switch.
Replace hazard
NG — —
switch.
PKIB8657E
RELATED OPERATION
Side turn signal lamp. Refer to LT-30, "SIDE TURN SIGNAL LAMP" .
Removal and Installation GKS000WO
PKIB8656E
NOTE:
Support side turn signal lamp harness with tape so that it won't fall into the front fender.
CAUTION:
Install the lamp housing with the bead facing up.
● Pawls (A)
● Lighting and turn signal switch (1) B
PKIC1018E
E
RELATED OPERATION
Steering column cover. Refer to IP-2, "INSTRUMENT PANEL ASSEMBLY" .
F
LT
● Pawls (A)
● Hazard switch (1)
PKIC1019E
RELATED OPERATION
Cluster lid C. Refer to IP-2, "INSTRUMENT PANEL ASSEMBLY" .
LT
TKWB2974E
CONSULT-II can display each diagnostic item using the diagnostic test mode shown following.
BCM diagnosis part Diagnosis mode Description
COMB SW DATA MONITOR BCM input data is displayed in real time.
1. CHECK SYSTEM A
Check which system malfunctioning switch belongs to input/output 1 - 5. And confirm that other switches in
malfunctioning system operate normally on the BCM data monitor. B
J
SKIB7592E
Check results
Other switches in malfunctioning system operate normally.>>Replace lighting switch or wiper switch. LT
Other switches in malfunctioning system do not operate normally.>>GO TO 2.
2. CHECK HARNESS L
Check malfunctioning system circuits between BCM and combination switch.
OK or NG
M
OK >> GO TO 3.
NG >> Repair harness or connector.
HATCH–BACK
B
LT
TKWB2975E
SEDAN
TKWB2976E
PKIC1021E
F
LT
L
SKIB7594E
M
Related Operation
Back door finisher upper. Refer to EI-15, "BACK DOOR TRIM" .
HIGH-MOUNTED STOP LAMP (SEDAN WITHOUT REAR SPOILER)
● High-mounted stop lamp mounting screws (A)
● High-mounted stop lamp (1)
PKIC1022E
PKIC1023E
Related Operation
Rear parcel shelf finisher. Refer to EI-18, "REAR PARCEL SHELF FINISHER" .
HIGH-MOUNTED STOP LAMP (SEDAN WITH REAR SPOILER)
● High-mounted stop lamp mounting bolts (A)
● High-mounted stop lamp cover (1)
● High-mounted stop lamp (2)
● Rear spoiler (3)
SKIB7595E
Related Operation
Rear spoiler. Refer to EI-13, "REAR SPOILER" .
REAR COMBINATION LAMP (STOP LAMP)
Refer to LT-49, "Removal and Installation" .
LT
TKWB2977E
SKIB7590E
G
● BCM (Body Control Module) controls parking, license plate and tail lamp operation. H
● IPDM E/R (Intelligent Power Distribution Module Engine Room) operates parking, license plate and tail
lamps according to CAN communication signals from BCM.
I
PARKING, LICENCE PLATE AND TAIL LAMP OPERATION
When the lighting switch is in 1ST position, BCM detects the LIGHTING SWITCH 1ST POSITION (ON) by
BCM combination switch reading function. And then, BCM sends position light request signal (ON) through
J
CAN communication.
When receiving position light request signal (ON), IPDM E/R turns ON tail lamp relay in IPDM E/R. And then,
parking, license plate and tail lamps go ON.
Combination meter receives position light request signal (ON) through CAN communication, and makes posi- LT
tion lamp indicator turn ON.
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" . L
Schematic GKS000X3
TKWB2978E
A
Ter- Signal Measuring condition
Wire
minal Signal name input/ Ignition Reference value
color Operation or condition
No. output switch B
OFF Approx. 0 V
C
Lighting, turn, wiper
Combination switch
2 BR Input ON
switch input 5 (Wiper intermittent Lighting switch 1ST
dial position 4) D
PKIB4957J
Approx. 1.0 V E
Ignition switch
11 L Input ACC — Battery voltage
(ACC)
F
G
OFF
H
Lighting, turn, wiper PKIB4960J
PKIB4958J
Approx. 1.2 V LT
Ignition switch
38 O Input ON — Battery voltage
(ON)
39 L Input/ L
CAN − H — — —
Output
40 P Input/
CAN − L — — —
Output M
Battery power
57 LG Input OFF — Battery voltage
supply
67 B Ground — ON — Approx. 0 V
Battery power
70 Y Input OFF — Battery voltage
supply
Inspection 1 Result Inspection 2 Result Inspection 3 Result Inspection 4 Result Replace or repair
Check “TAIL OK — — Replace BCM.
LAMP SW” status
OK Replace lighting
on the BCM data NG — —
monitor. switch.
Check BCM
OK self-diagnosis Check CAN com- ● Repair harness or
result. munication. Refer connector.
Start “EXTER- to LAN-2, "Pre-
U1000 — — — ● Replace BCM.
NAL LAMP” on cautions When
Using CONSULT- ● Replace IPDM E/
the IPDM E/R
active test, and II" . R.
check if park- Start “EXTER- Replace parking,
Check circuits
ing, license NAL LAMP” on OK license plate and tail
Check park- between parking,
plate and tail the IPDM E/R lamp bulbs.
ing, license OK license plate and
lamps illumi- active test, and
plate and tail tail lamps and Repair harness or
nate. OK check parking, NG
lamp circuit grounds. connector.
NG between IPDM license plate and
E/R and park- tail lamps output
ing, license voltage of IPDM NG — — Replace IPDM E/R.
plate and tail E/R.
lamps. Repair harness or
NG — — — —
connector.
A
Inspection 1 Result Inspection 2 Result Inspection 3 Result Replace or repair
● Replace BCM.
OK — —
Lamps go off Check “IGN ON ● Replace IPDM E/R. B
when ignition SW” status on the OK Replace BCM.
Check ignition switch
switch is OFF. BCM data monitor.
NG ON signal input voltage Repair harness or con-
of BCM. NG
Make sure that lighting nector. C
switch is OFF. And then Lamps go off
check if ignition switch when ignition — — — — Replace IPDM E/R.
is ON or OFF when switch is ON. D
parking, license plate
and tail lamps go off. Start “EXTERNAL Check “TAIL LAMP SW” OK Replace BCM.
LAMP” on the OK status on the BCM data
Lamps do not Replace lighting
IPDM E/R active monitor. NG
go off when
test, and check if
switch. E
ignition switch
parking, license
is ON and OFF.
plate and tail lamps NG — — Replace IPDM E/R.
go off.
F
Bulb Replacement GKS000XB
J
PKIC1055E
Related Operation
Trunk lid finisher inner. Refer to EI-23, "TRUNK ROOM TRIM & TRUNK LID FINISHER" . LT
LICENSE PLATE LAMP (HATCH–BACK)
● License plate lamp bulb socket (1)
● License plate lamp bulb (2) L
SKIB7596E
PARKING LAMP
Refer to LT-15, "Bulb Replacement" .
TAIL LAMP
Refer to LT-49, "Bulb Replacement" .
PKIC1056E
Related Operation
Trunk lid finisher. Refer to EI-23, "TRUNK ROOM TRIM & TRUNK LID FINISHER" .
LICENSE PLATE LAMP (HATCH–BACK)
● Plastic clip (A)
● License plate lamp (1)
● Back door (2)
SKIB7597E
PARKING LAMP
Refer to LT-14, "Removal and Installation" .
TAIL LAMP
Refer to LT-49, "Removal and Installation" .
STOP/TAIL LAMP BULB, REAR TURN SIGNAL LAMP BULB AND BACK–UP LAMP BULB
(SEDAN)
B
Stop/tail lamp (1) : 12V - 21/5W
Rear turn signal lamp (2) : 12V - 21W (amber)
Back–up lamp (3) : 12V - 21W C
E
PKIC1034E
Related Operation
F
Trunk side finisher. Refer to EI-12, "TRUNK LID FINISHER" .
STOP/TAIL LAMP BULB, REAR TURN SIGNAL LAMP BULB AND BACK–UP LAMP BULB
(HATCH–BACK) G
Stop/tail lamp (1) : 12V - 21/5W
Rear turn signal lamp (2) : 12V - 21W (amber)
H
Back–up lamp (3) : 12V - 21W
J
SKIB7601E
PKIC1035E
Related Operation
Trunk side finisher. Refer to EI-23, "TRUNK ROOM TRIM & TRUNK LID FINISHER" .
CAUTION:
Seal packing cannot be reused.
SKIB2526J
HATCH BACK
B
LT
TKWB2979E
SEDAN
TKWB2980E
MAP LAMP A
PKIA0182E
F
SKIB7603E J
Removal and Installation GKS000XH
MAP LAMP
● Pawls (A) LT
● Map lamp (1)
PKIC1038E
SKIB7604E
MAP LAMP
● Sunroof switch mounting screw (A)
● Sunroof switch (1)
PKIC1039E
SKIB7605E
G
Room lamp (when room lamp switch is in DOOR position) ON/OFF is controlled by timer according to signals H
from key switch, front door switch driver side, front door lock actuator (driver side) (unlock sensor), etc.
room lamp timer control settings can be changed within 5 seconds.*
* Factory setting gradual dimming and brightening time is 1 second. I
INTERIOR ROOM LAMP TIMER OPERATION
BCM performs timer control (30 seconds)* to turn ON/OFF of the room lamp when room lamp switches are in
DOOR position. In addition to it, dimming/brightening control also takes place for maximum 5 seconds*. J
● When BCM detects driver door is unlocked, and the key is not inserted in the ignition key cylinder (key
switch OFF), it determines that conditions for interior room lamp timer operation are met, and turns the
room lamp ON for 30 seconds. LT
● When BCM detects key is removed from ignition key cylinder (key switch OFF), it determines that condi-
tions for interior room lamp timer operation are met, and turns the room lamp ON for 30 seconds.
● When BCM detects driver door is closed, and the key is not inserted in the ignition key cylinder (key switch L
OFF), it determines that conditions for interior room lamp timer operation are met, and turns the room
lamp ON for 30 seconds.
BCM does not activate the timer even a door other than the driver door is opened. M
*: Setting can be changed by CONSULT-II. Refer to LT-59, "WORK SUPPORT (INT LAMP)" .
Conditions for Canceling Timer
Timer operation is cancelled in any of the following conditions.
● Driver door is locked.
● Driver door is opened.
● Ignition key switch is ON.
INTERIOR ROOM LAMP BATTERY SAVER FUNCTION
If the room lamp switch is in DOOR position and the room lamp left illuminated due to incompletely closed
door, BCM turns OFF the room lamp in 30 or 60 minutes to prevent run down of the battery. (Timer setting can
be changed by CONSULT-II. Refer to LT-60, "WORK SUPPORT (BATTERY SAVER)" .)
● When the ignition key switch is turned from ON to OFF, the timer is activated.
● When any of the following switch signal condition is changed with the ignition key switch in OFF position,
the timer is activated when the change is occurred.
Switch signals: front door switch driver side and passenger side signal, rear door switch LH and RH signal,
front door lock actuator (driver side) (unlock sensor) signal, key switch signal, central door unlock switch signal
and remote control unlock signal.
Schematic GKS000XK
LT
TKWB2981E
SKIB3419J
PKIB4960J
SKIB3419J
PKIB4950J
Approx. 11.0 V
48 W
Rear door switch
Input OFF Rear door switch LH
C
LH signal OFF (closed)
D
PKIB4960J
MODE 1 2 3 4 5 6 7
Time (sec.) 0.5 1 2 3 4 5 0
NOTE: J
Check if door lock operates normally.
Inspection 1 Result Replace or repair
LT
OK Replace BCM.
Check “SET I/L D-UNLCK INTCON” status on the BCM work support.
NG Change set value.
L
Bulb Replacement GKS000XQ
ROOM LAMP
● Room lamp lens (1)
M
● Room lamp bulb (2)
Room lamp : 12V - 8W
PKIC1048E
ROOM LAMP
● Metal clip (A)
● Room lamp lens (1)
PKIC1049E
ILLUMINATION PFP:27545
A
System Description GKS000XT
LT
Schematic GKS000XU
TKWB2982E
LT
TKWB2983E
PKIC1053E
Related Operation
Glove box assembly. Refer to IP-2, "INSTRUMENT PANEL ASSEMBLY" .
ASHTRAY ILLUMINATION
● Ashtray illumination bulb socket (1)
● Ashtray illumination bulb (2)
Ashtray illumination bulb : 12V - 1.4W
PKIC1054E
Related Operation
Instrument finisher D. Refer to IP-2, "INSTRUMENT PANEL ASSEMBLY" .
LT