Professional Documents
Culture Documents
2). Issues with 4G MIMO mode control can cause by following statement, except:
1. Inappropriatea selection between the two transmission schemes
2. Ping-Pong between spatial diversity and spatial multiplexing
3. Switching between transmission schemes to create additional signalling
4. Inappropriate' selection between spatial diversity and spatial multiplexing
5. All options are incorrect
4). In the 3GPP evolved release 10, transmission modes are support to:
1. Single Antenna Port or Tx Diversity & 4x4 MIMO in the downlink
2. Tx Diversity & Closed Loop Spatial Mux with single Layer
3. 8x8 MIMO in the downlink or Dual Layer Beamforming
4. Tx Diversity & Closed Loop Spatial Mux (Close Loop MIMO)
5. All options are incorrect
8). When is the best timing to get measurement of UL RSSI Interference that possible indicate
internal hardware problem?
1. At non busy hour get the RSSI_PUCCH_L EVEL
2. At busy hour get the RSSI_PUSCH_ EVEL
3. At non busy hour get the RSSI_PUSCH_L EVEL
4. At busy hour get the RSSI_PUCCH_ EVEL
5. All options are incorrect
12). Which event that The non-contention based random access are applicable to ?
1. All Event
2. RRC re-establishment
3. handover and DL data arrival
4. Initial Access
5. All options are incorrect
17). Handover are essenstial procedure for UE moving from cell to cell. What are the 4G Handover Event ?
1. Al—Interfreq, A2—Intrafreq, A3—BetterCell, A4—BetterCell, A5— CoverageBased
2. Al Intrafreq, A2 Interfreq, A3 BetterCell, A4 InterRAT, A5- CoverageBased
3. A1—Intrafreq, A2—InterRAT, A3—CoverageBased, A4— Interfreq, A5 BetterCelI
4. Al BetterCell, A2 Intrafreq, A3- Interfreq, A4- CoverageBased, A5 InterRAT
5. All options are incorrect
19). Is there any relation between low 2G CSSR and high capacity ?
1. Yes there is, CSSR is all about congestion
2. It depends on the CSSR formula
3. Depend on the site to site distance
4. No relation because CSSR is about Quality
5. All options are incorrect
20). Which of the following that you will not do if you find 2G TBF Downlink Success Rate is not pass
the target baseline ?
1. Adjust GTRX number and CDED/CDEF
2. Switch GTRX to better quality TRXs
3. Reset the GTRX, GENA, EGENA
4. Downtilt from 4 to 10
5. All options are incorrect
24). When throughput test shows low throughput value for TCP, but UDP throughput is high, what could
be the cause?
1. Not enough BTS baseband capacity
2. Shaping is enabled in the transport path between the core and eNodeB
3. Packet loss somewhere between the core network and eNodeB
4. Test is done too close to the site
5. All options are incorrect
26). what is below is not correct condition that cell reselection will trigger in 4G inter-frequency?
1. Squal <= SlntraSearchQ
2. RSRQ >= qQualMin + slntraSearchQ
3. Srxlev <= SnonlntraSearc hP (benar)
4. RSRP <= qrxlevmin + slntraSearchP
5. All options are incorrect
27). what is below is not correct condition that cell reselection will trigger in 4G intra frequency?
1. Qrxlevmeas - Qrxlevmin <= Sintrasearch
2. Srxlev <= Sintrasearch (benar)
3. Qrxlevmeas <= Qrxlevmin + Sintrasearch
4. Qrxlevmeas - Qrxlevmin < Sintrasearch
5. All options are incorrect
29). Which of the following parameter mush have the same setting for Pcell and Scell when CA is activated?
1. riEnable (rank indication reporting enables). 2. periodicCqFeedback Type (periodic CQI feedback type) 3.
cqPerSbCycK (Periodic CQI sub-bands cycles) 4. caShecFairFact (carrier aggregation scheduling fairness
control).
1. 1), 2) and 4)
2. 1), 2), 3) and 4)
3. 2), 3) and 4)
4. 1), 3) and 4)
5. All options are incorrect
35). How many carrier per pipe maximum for AHHB Nokia AirScale RRH 4T4R ?
1. Up to 16
2. Up to 8
3. Up to
12 4 Up to
4
5. All options are incorrect
36). In 4G Intrafreq handover, in what condition UE will not measure or report any neighbor cells RSRP ?
1. If RSRP of neighbor cell is lower than threshold1, only neighbor cell is measured
2. If RSRP of serving cell is greater than threshold1, only serving cell is measured
3. if RSRP of neighbor cell is greater than threshold1, only serving cell is measured
4. If RSRP of serving cell is lower than threshold1, only serving cell is measured
5. All options are incorrect
39). For Volte services, which QCI will be use as resources bearer ?
1. QCl2 and QCI8
2. QCI3 and QCI5
3. QCI1 and QCI5
4. QCI3 and QCI7
5. All options are incorrect
41). The CQI is defined as a table containing 16 entries with modulation and coding schemes (MCSs).
Which one is correct for representing the modulation ?
1. CQI 1-6 = QPSK, CQI 7-9 = 16QAM, CQI 10-15 = 64QAM
2. CQI 1-5 = QPSK, CQI 6-8 = 16QAM, CQI 9-15 = 64QAM
3. CQI 1-6 = QPSK, CQI 7-10 = 16QAM, CQI 11-15 = 64QAM
4. CQI 1-6 QPSK, CQI 7-11 = 16QAM, CQI 12-15 = 64QAM
5. All options are incorrect
43). What is the parameter you will change if you want to decide the absolute priority of the 4G serving cell
1. cellReSelPrio (This is the priority of the own cell. It depends on the layering plan. The cell reselection
priority parameter defines the absolute priority of the serving layer. 0 means the lowest priority. Equal
priorities between RATs are not supported according to [3GPP 36.304].)
2. uCelResPrio (Depends on layering plan. LTE prio > 3G prio > GSM prio. Absolute priority of the UTRA
carrier frequency. Equal priorities between RATs are not supported according to [3GPP 36.304].
3. gcelResPrio (LTE prio > 3G prio > GSM prio. Its value depends on layering plan of the operator. Usually
GERAN would be the last resort coverage layer and low priority is used. Absolute priority of the GERAN
carrier frequency. Equal priorities between RATs are not supported according to [3GPP 36.304].
4. eutCelResPrio (Depends on layering plan. Absolute priority of the EUTRA carrier frequency. Equal
priorities between RATs are not supported according to [3GPP 36.304].
5. All options are incorrect
44). There is 4 types on preamble, what is the significant difference between this 4 types ?
1. PRB Number
2. Reference Signal
3. Cell Range
4. Guard Time
5. All options are incorrect
47). Which of the folllowing is not correct about the reason of 4G ERAB Drop ?
1. HARQ ACK/NACK RLF
2. PUSCH RLF
3. TA Expiry
4. Srxlev > 0 and Squal > 0
5. All options are incorrect
48). Which network element of NOKIA's LTE solution performs the E2E monitoring and reporting functions?
1. Flexi NG
2. Charge@once
3. PCS-5000
4. Netact
5. All options are incorrect
49). What parameter to define the maximum numbers of preambles allowed in one preamble ramping cycle ?
1. PowerRampStepPRACHpreamble (“The power ramping step size parameter defines the power
increment step size for Random Access preamble transmission.”)
2. PRACHRequired ReceivedCI
3. PRACH_Preamble_retrans
4. UETxPowerMax PRACH
5. All options are incorrect
50). Which network element always triggers the user network authentication process
1. S-GW
2. MME
3. P-GW
4. eNodeB
51). A new site is on air with condition low revenue sites. What will you NOT do ?
1. Recommend to add more new site to increase the revenue
2. Check the antenna if properly directed to residence
3. Check the coverage parameter
4. Check the hardware if properly working
5. All options are incorrect
52). What is the bad impact on applying Closed Loop Power Control in 4G ?
1. UL RSSI will degraded
2. DL User Throughput will degraded
3. No bad Impact
4. UL User Throughput will degraded
5. All options are incorrect
54. Select the factor that does NOT improve the Spectral Efficiency In Massive MIMO ?
1. Multiuser gain
2. UL interference cancellation
3. 3D beamforming
4. SINR Improvement due to narrower UE beam
5. All options are incorrect
57. Without this feature VOLTE call will drop when it leaves the LTE coverage ?
1. SRVCC to WCDMA/SRVCC to GSM
2. Service based Mobility Threshold
3. Service Mobility Trigger,
4. Dedicated Mobility Thresholds for SRVCC
5. All options are incorrect
60. Which of the following options does NOT improve the latency as part of the Radio Network Optimization
Procedures?
1. Enabling/Disabling Proactive Scheduling
2. Tuning the scheduling request period
3. Tuning DRX cycle duration
4. Increasing PUCCH capacity
5. All options are incorrect
63. How does MIMO improve spectral efficiency, network capacity and throughput
1. By using multiple uplink and downlink transmitters
2. By using multiple receiv and transmit antennas
3. By using multiple eNB sites
4. By using multiple transmit and receive amplifiers
5. All options are incorrect
66. What air interface technology has been defined for LTE uplink ?
1. SC_FDMA
2. WCDMA
3. GSMK
4. OFDMA
68. what is below is correct condition that cell re-selection will trigger measurement in 4G intra-frequency?
1. If cannot do inter-frequency handover then do intra-frequency handover
2. Cell re-selection only happen in 4G Inter-frequency
3. Qrxlevmeas > Qrxlevmin + Sintrasearch
4. Qrxlevmeas <= Qrxlevmin + Sintrasearch
5. All options are incorrect
69. what is below is correct condition that cell reselection will trigger in 4G inter-frequency?
1. RSRP <= qrxlevmin + sNonlntraSearchP
2. If cannot do intra-frequency handover then do inter-frequency handover
3. RSRP > qrxlevmin + sNonlntraSearchP
4. Cell re-selection only happen in 4G Intra-frequency
5. All options are incorrect
70.You are in optimizing 1 new site, you see 2G TCH Blocking is not Pass the target KPI. What will you do ?
1. Disable the Halfrate so the cell can go full rate to accomade full service
2. Check if VOLTE 4G is not activated yet
3. Adding PDCCH channel to reduce the tch blocking
4. reduce the SDCCH channel, so that no UE can not do setup
5. All options are incorrect
72. What will you do if find cell with high PRB Utilization ?
1. Wait until any PO new site suurounding released and ON AIR
2. Offload to 3G with high BB Util
3. Downtilt from 2 to 10
4. Try to do payload sharing to neighbor cells
5. All options are incorrect
74. in Mapinfo you can map the entire site in region to get
information visually. What is the function if highlighted yellow in
picture ?
1. To query selected data from table
2. To plot the position of the site in the map
3. To visually mapping the category of point
4. To make buffer like 5 Km from point
5. All options are incorrect
75. After check MDT, you find that low SNIR happen across the main street. What is the best will you do?
1. Check if any multiple server in main street and do coverage audit
2. Switch off all sites, except one site to cover the street
3. Uptilt all cells that cover the main street to get best coverage
4. Downtilt all cells that cover the main street to get best coverage
5. All options are incorrect
77. Which factors can NOT be a cause for bad KPI for HOSR ?
1. IMSI
2. X2 quality
3. Layer Priority
4. UL RSSI
5. All options are incorrect
79. You are in optimizing 4G New Site, but you find that the Packet Loss Rate is high. What will you do first?
1. Check in hourly basis if packet loss is happen frequently or just a spike
2. Immediately escalate to transport Engineer to seek support
3. Perform drive test to check the field impact
4. Check hardware alarm if any baseband module broken
5. All options are incorrect
80. You are optimizing 1 new site and 4G Payload suddenly increase and impact to your CSSR KPI, what will
you not do immediately?
1. Check if any site surrounding site if shutdown
2. Check if any promo campaign to up the sales
3. Check your validity of your measurement if any double counting
4. Payload Increase is good, so make justification for CSSR KPI
5. All options are incorrect
81. From Drive Test Result, to check coverage of the cells, What plotting will you used ?
1. RxQual on dedicated mode
2. RxLevel (dBm) on idle mode
3. RxQual on Idle mode
4. RxLevel (dBm) on dedicated mode
5. All options are incorrect
83. Do you think this formula is correct or not CSSR 4G = RRC – SR% X RAB-SR% X S1-SR%?
1. Not correct, because CSSR 4G only count RRC-SR
2. Correct, but must confirm to customer if S1-SR included or not
3. Correct, but must be confirm to customer if S1-SR included or Not
4. Correct and must have this 3 component
85. There is a complain 2G cannot make a call at all, what the best should you check ?
1. Check 2G can do PS data
2. Check if connected to correct SGSN
3. Check BCCH frequency is clear or not from interference
4. Check LAC-CI already registered in Core
88.Which sentence is NOT true concerning Cell trace and Subscriber trace?
1.Both Cell trace and subscriber Trace, indentify UE based upon their IMSI
2. Cell trace records all the UEs connected to the hell, whereas Subscriber Trace record only specific UE
3. The cell trace, trace activation command is sent to the enb, whereas the Subscriber Trace, Trace
Activation command is sent to the MME
4. Cell trace does not capture the subscriber identify, whereas Subscriber Trace captures the IMSI
89.Which statement(s) correctly describe the SBTS site configuration evolution” <br/>1. Cell sets define on
sub baseband module level are combined in independent building blocks to build an SBTS configuration
<br/>2.LTE and SRAN cell set can flexibly combined to build target configuration <br/>3.”Cell set” approach is
adobted from LTE. Requires higher effort on LTE migration from legacy RAT to SRAN in comparison to the
“Profile” approach <br/>4. “Cell set” concept is only applicable to the shared operation SRAN cells
1. 2 and 3
2. 2 and 4
3. 1 and 4
4. 1 and 4
92.Which of the following is NOT a use case for NPO MUSA tool?
1.Coverage Optimisation
2.Multilayer SRAN coverage
simulation 3.Neighbours analysis and
processing 4.Automated parameter
audit
93.To troubleshoot an ul throughput problem in a live network, a drive test log has been collected with
simultaneous TTI trace. In order to find the correct UE in MAC TTI trace, which information is required from
the drive test log?
1. IMSI
2. Data Radio Bearer
ID 3.C-RNTI
4.M-TMSI
94.Which is NOT a possible couse for an eNodeB-triggered radio link failure (FDD
case)? 1.PDDCH Order Failure
2.Max RLC
Retransmission 3.CQI RLF
4.HARQ RLF
95.Which tool does NOT belong MINT (Management and Intelligence Tool) Suite?
1.PKDB
2.Network Auditor
3.PB2
4.RADAR
97.Which 3GPP release starts using the term LTE Advance Pro?
1.Rel 14
2. Rel 13
3. Rel 15
4. Rel 12
98. Nokia Single RAN solution is designed to support multiple Radio Access Technologies with common or
shared functionalities. Which og the following statement are correct?<br/> 1.Single FSMF baseband capacity
can be shared between GSM+WCDMA or GSM+LTE but not LTE+WCDMA<br/>2.Common BTS OAM to
simply site creation commissioning and configuration process, where IOMS is re-used to handle SRAN
operability<br/>3.SRAN solution is compatible with FSME, FSMF and Air Scale system module<br/>4.Air
Scale System Module can be used as two logical SBTSs in full subrack, or one logial SBTS and one logial
LNBTS and one logial LNBTS in full subrack
1.2 and 4
2.1 and 2
3.2 and 3
4.1 and 4
99. Select all the statements) which are correctly describing the Uplink Power Control
function/algorithm:<br />1. Uplink Power Control is trade-off between inter-cell interference and own
cell throughput<br />2. Closed loop ULPC is UE oriented, SIN and RSSI target window power control
steering<br />3. Interference Aware ULPC replace Closed Loop ULPC for PUSCH/SRS, but keep OLPC algorithm
untouched<br />4. UL Interference Offset feature overcomes the impact of power restrictions on PUCCH
allocating PUCCH away from power restrick region.
1. 1, 2, 3 and 4
2. 1, 3 and 4
3. 1 and 3
4. 2 and 4
100.Which protocol stack layer within the enb is responsible for uplink and downlink adaptation?
1. RLC Layer
2. MAC Layer
3. Physical Layer
4. PDCP Layer
101.What could be the reason for high average ping round trip time under good radio conditions in an
unloaded network?
1.256 QAM in downlink is disabled causing bandwidth limitation and hence lager ping response scheduling
delay
2. Uplink periode CQI reporting interval is too long
3. Uplink pro-active scheduling timer value is shorter than ping transmission interval
4. Not enough Scheduling Request resources to accomdate al RRC connected UEs in the call
102. Which statement is Incorrect about KPI : E-UTRAN Drop Ratio, RAN View?
1. E-RAB release due to “No Radio Resources Available” initiated by enb are caunted as abnormal releases
2.RAN point of view means that as abnormal E-RAB drops only those ones Initiated by enb are counted
3.This KPI describes the radio of abnomally released (dropped) E-RAB from RAN point of view
4. In denominator of the formula normal E-RAB releases due to successful HO to Ehrdpd are not counted
107. Which Global NPO community contains network planning and optimization guidance material grouped
per technology or product?
1. NPO Service Wiki
2. NPO Modular Working Item Wiki
3. Services Community
4. Radio Community Wiki
108. Which of the following is NOT correct about the reason of 4G ERAB Drop?
1.PUSH RLF
2.Srxlev > 0 and Squal > 0
3.CQI Report RLF
4. HARQ ACK / NACK RLF
5. All Options are incorrect
110.Which interface allows application data transfer through the Serving Gateway
1. LTE Uu
2. X2
3. S1-MME
4. S1-U
111.Which managed objects are not a part of GSM technology (more than one option can be valid)
1.WCEL
2. BTS
3. TRX
4. BCF
113.Which answer can NOT be applied to the following statement: When a UE is in RRC_Connected mode and
RRC security is active, the UE can trigger Radio Link Failure (RLF) and initiated RRC Connection Re
establishment due to:
1.T310 Timer
Expiry 2.TA Timer
Expiry
3.Reaching the maximum number of UR RLC retransmissions
4.Handover failure (T304 expiry)
115.You are in optimizing 1 new site and 4G Payload suddenly increase and impact to your CSSR KPI, what will
you NOT do immediately?
1.Check your validit of your measurement if any double counting
2.Check if any site surrounding site if shutdown
3. Payload Increase is good, so make justification for CSSR KPI
4. Check if any promo compaign to up the sales
117.Cloud based RAN uses the cloud operating model. Which of the following is NOT a benefit of Telco Cloud:
1.Optimized hardware utilization by resource sharing
2.Simplified Operations by allowing multiple organization to use same platform simultaneously
3.Decoupled software and hardware as there is not vendor lock in for hardware
4.Increased end user throughput by improving spectral efficiency
118.Which of the following MIMO statement is TRUE for radio pilot overhead?
1.In TDD, it is independent of the number of spatially multiplexed Ues
2.In FDD, It depends on number of antennas and the number of spatially multiplexed UEs
3.In TDD, it depends on number of antenna and the number of spatially multiplexed UEs
4.In FDD, it is only independent on the number of spatially multiplexed Ues
122.Which scheduler considers the UL interference level and the signal strength of each UE during resource
allocation?
1.Interference aware
scheduler 2.Fair scheduler
3.Channel aware scheduler
4.Channel unaware
scheduler
127.You are in optimizing 1 new site, you see 2G TCH Blocking is not Pass the target KPI. What will you do?
1.Adding PDDCH channel to reduce the tch blocking
2.Enable the Halfrate so the cell can increase capacity
3.Add the SDCCH channel to reduce TCH Blocking
4.Disable the halfrate so the cell can go full rate to accomade full service
129.How many subframes are within each half-frame in a LTE TDD Frame Type
2? 1.14
2.7
3.5
4.10