Professional Documents
Culture Documents
EXPERIENCE
Experience the LUXURY
with Unparalleled
Essence of Pleasance Total Home Control
a3etechsupport@lutron.com | www.lutron.com/asia
Entire Home Solutions | HomeWorks Entire Home Solutions | HomeWorks
Employee Details Compatibility Chart of Dimmable lamps with Lutron dimming power modules
Name:
Direct Dimming Indirect Dimming
Lamp Type
Leading Training 0-10V DALI
Company Name: Incandencet /Halogen Yes Yes No No
MLV Yes No No No
myLutron Email ID:
ELV Depend on transformer Yes No No
Lutron account number: LED (Needs Driver) Depend on driver Depend on driver Depend on driver Depend on driver
Device:
Any equipment's which is directly connected to QS link is called as device.
Key terms in HomeWorks system 03
Switch Leg:
Smallest output controlled by HomeWorks system is called as switch leg
Designing steps for HomeWorks systems 04
PDU:
Power required by device is express in PDU (power draw units). The device which receives 230V
Summery of HomeWorks design 05
doesn't consume PDUs e.g. Switching module. The device which doesn't receive 230V will consume
PDUs from QS link e.g. keypad & QSM.
HomeWorks Wireless
99 99 16 6 (RF link) 5
(RF Link)
1
Entire Home Solutions | HomeWorks Entire Home Solutions | HomeWorks
Design Steps For HomeWorks System Step 3 Determine The Control Station Plan,
Add Convenience and Expand The Functionality:
Step 1 Select System Components Wired Keypads
The processor is the heart of the lighting control system providing intelligence and offering a centralized
connection point for control and communication. International seeTouch keypad Palladiom keypad Alisse keypad
Models available with 2-10 Models available with Models available
Low voltage QS Link Power programmable buttons 2-8 programmable with 1-9
Processor Wire landing Board
enclosure supply Select models available buttons programmable
with raise/lower buttons Dynamic backlight buttons
and infrared receiver management
Control up to 4 10A Control up to 4 5A Control up to 4 10A Provide control of dimmable LED in addition to Contact Closure Input / Output Integration
zones of lighting zones of lighting zones of lighting incandescent/ halogen / electronic low voltage,
fixtures fixtures fixtures (Switched relay or magnetic low voltage light sources
Provide 1 CCO 0-10V dimming International seeTouch Alisse Contact closure Wallbox contact DIN-rail Switching Power
DIN-rail DALI power modules DIN-rail Motor power modules keypad keypad Interface closure input interface module
2 3
Entire Home Solutions | HomeWorks Entire Home Solutions | HomeWorks
Roller Shades Drapery Venetian Roman Sky Light Kirbe Smart Shade Panel
A/V equipment Touch Panel Control Security System
(by other) (by other) (by other)
Add one power supply for each shades/drape. Plug In Power Supply
Note : Integration is done on LEAP (Lutron Extensible Application Protocol)
QS link Modbus
FCU
4 5
Entire Home Solutions | HomeWorks
1 SELECT SYSTEM COMPONENTS 2 ADD LOAD CONTROLLERS 4 MOTORIZED SHADES, DRAPERIES AND OTHER LOADS
3 ADD CONTROLS
6 7
Entire Home Solutions | HomeWorks Entire Home Solutions | HomeWorks
QS Link limit : 100 devices & 512 Switch legs per link
Leading Trailing
edge / edge / Type of load
Device Switch-leg PDUs DIN RAIL Switch
Switching 0-10 V Forward Rivers
Power Min Load which
Product Description Model number count Module Name Legs Max / Zone criteria / zone module can
count count Phase Phase
control
Dimming Dimming
1 Link HomeWorks® QSX processor HQP7-1 1 0 -8
Switching
2 Link HomeWorks® QSX processor HQP7-2 1 0 -8 Module 2000 W
4 Yes No No No NA Any type
Power Supply QSPS-DH-1-75-H 0 0 +75 LQSE-4S-10D or 10A
of Switching
lighting
Low voltage enclosure 14 inch L-LV14-230 NA NA NA Switching 1000W loads.
Module 4 Yes No No No or 5A NA
Low voltage enclosure 21 inch L-LV21-230 NA NA NA LQSE-4S5-230D
Wirelanding board QS-WLB NA NA NA
0-10-volt
Connect Bridge CONNECT-BDG2-2 0 0 0 0-10 V
4 Yes Yes No No 20 drivers NA analog
LQSE-4T-10D
Hight power Switching module (DIN-rail) LQSE-4S10-D 1 4 0 drivers
8 9
Entire Home Solutions | HomeWorks QS Entire Home Solutions | HomeWorks
Use UPS power supply for giving control input power to DIN rail power modules
Load phase dimming power module properly in case of Line dimmable LEDs
Use terminal blocks with bypass jumpers for termination of loads on DIN rail power modules
Do Install occupancy sensor 1.5 m away from HVAC duct and hot lamp source
Maximum
Wiring between Minimum Size of cable and specifica on
Distance
Processor to QS devices 150m Lutron QS link cable 1 Sq.mm
Processor to QS devices 600m Lutron QS link cable 4 Sq.mm
Processor to Ethernet Switch 95m CAT6
Hybrid repeater to Hybrid repeater 305m Lutron QS link cable 1 Sq.mm
Wired QSM to wired sensors 46m 3 core 0.5 Sq.mm
QSE IO/WCI/SeeTouch CCI to CCI input device 45m 2 core 0.5 Sq.mm
DALI module to DALI driver 300m 2 core 1.5 Sq.mm
2 core 1-4 Sq.mm power wire
0-10 V module to 0-10 V driver 150m
2 core 1.5 Sq.mm dimming wire
38 m Lutron QS link cable 1 Sq.mm
Smart shade panel output to Shade EDU 61m Lutron QS link cable 1.5 Sq.mm
152m Lutron QS link cable 4 Sq.mm
10 11