Professional Documents
Culture Documents
Preface
Main Operation Screen ESM-3723 series Temperature + Humidity control devices, are designed for the control of industrial
Process High Alarm Process Low Alarm
ESM-3723 ESM-3723
processes. PID or On / Off control form under the control of the process is a device that can
Alarm Alarm
Output Output
O1 O1 respond to your special needs.
SET SET
ON ON ü ü
1.1 Environmental Ratings
Temperature+Humidity
OFF
OFF When SET button is pressed for 3 Note1: If programming Programming Mode
Process Value Process Value seconds, “P” led turn. If programming mode accessing password Entering Screen
Alarm Set Alarm Set mode entering password is different is 0, Temperature Unit Press SET button for
from 0, programming mode entering screen is observed accessing to the Operating Temperature : 0 to 50 °C
Deviation Band Alarm screen will be observed. instead of programming password entering
Alarm screen
Output Max. Operating Humidity : 90% Rh (non-condensing)
Password Entering Screen Password Entering Screen
ON
ESM-3723 ESM-3723
O1 O1 Altitude : Up to 2000 m.
SET SET
c
OFF Forbidden Conditions:
ü ü Corrosive atmosphere
Process Value
( - Alarm Set) ( +Alarm Set)
Explosive atmosphere
Home applications (The unit is only for industrial applications)
Deviation Range Alarm Enter programming mode accessing
password with increment and
Press SET/OK button for
entering the password.
ESM-3723 77 x 35 DIN Size
Alarm
Output
decrement buttons. Digital Temperature+Humidity Controller 1.2. General Specifications
Note2: If programming mode accessing password is 0, only three parameters are accessible, and the
parameter values can be changed. - 4 Digits for Temperature Display
ON Temperature Unit Selection Standard
Programming Screen - 4 Digits for Humidity Display
230VV( ±%15)50/60Hz
ESM-3723
Parameter Value - Temperature Sensor Input Optional Supply
OFF
ESM-3723 ESM-3723
NTC, PTC, PT-100, 0/2..10V, 0/4..20mA or ProNem Mini PMI-P Voltage Power Supply
O1
13 14 2
29 mm / 1.14 inch
Temperature Sensor Input : NTC, PTC, PT-100,0/2..10VZ,0/4..20mAZ or Note-1: If input type is selected PTC or NTC (BC= 2, 3), Temperature sensor is given with the Repair and maintenance service information:
ProNem Mini PMI-P device.For this reason, if input type is selected as PTC,sensor type (V = 0,1 or 2) or if input type is Emko Elektronik Sanayi ve Ticaret A.Þ.
NTC input type : NTC (10 kW @25 °C ) selected as NTC, sensor type (V = 0, 3 or 4) must be declared in ordering information. Demirtaþ Organize Sanayi Bölgesi Karanfil Sk. No:6 16369 BURSA/TURKEY
Phone : +90 224 261 1900
Fax : +90 224 261 1912
15 16 3 4
2.3 Panel Mounting and Removing 3.2 Device Label and Connection Diagram 5.1 Programming Mode Parameter List Hysteresis Parameter for Temperature ( Default = 0.1 °C )
230VV CONNECTION DIAGRAM Temperature Unit Selection Parameter ( Default = 0 ) From 1 to 10°C for NTC,PTC, PT-100 (0°C, 100°C)
1 From 1 to 18°F for NTC,PTC ,PT-100 (32°F, 212°F)
°C selected. From 0.1 to 10.0°C for NTC, PTC, PT-100 (0.0°C,100.0°C)
PTC Temperature and 0/4..20mA Humidity Sensor Input connection
1 °F selected. From 0.1 to 18.0°F for NTC, PTC, PT-100 (32.0°F,212.0°F)
Decimal Seperator Enabling Parameter ( Default = 0 ) From 1 to 10°C for ProNem Mini PMI-P (-20°C, 80°C) ,From 1 to 18°F for ProNem Mini
PMI-P (-4°F,176°F),From 0.1 to 10.0°C for ProNem Mini PMI-P (-20.0°C,80.0°C)
P/N : ESM-3723-5.2.5.0.1/01.01/1.2.0.0
5A @250VV 3x3A@ 250V V 230 VV ± 15% None. From 0.1 to 18.0°F for ProNem Mini PMI-P (-4.0°F,176.0°F).
50/60Hz - 1.5VA
In ON/OFF control algorithm, temperature
HEAT
ALARM/
ALARM
Only Temperature parameters with decimal seperator.
a
HUM.
HEAT.
value is tried to keep equal to set value by Temperature
HUM.
3
2 Only Humidity parameters with decimal seperator. opening or closing the last control element.
2 1 2 3 4 5 6 7 8 9 10 11 12 ON/OFF controlled system, temperature
Only Temperature and Humidity parameters with decimal seperator. thSt thSt
1-Before mounting the device in your panel, make 1-Pull mounting clamps from left and right value oscillates continuously. Temperature
N L Set
sure that the cut-out is of the right size. fixing sockets. Note : When value of or parameters are changed , the values of , , , , value’s oscillation period or amplitude
2-Pull the unit through the front side of the - + , , , , , , , , , , , , and parameters around set value changes according to Time
2-Insert the device through the cut-out. If the N 230 VV ± 15%
mounting clamps are on the unit, put out them panel 14A T Fuse 50/60Hz - 1.5VA should be changed accordingly. controlled system. For reducing oscillation Control
c
L period of temperature value, a threshold Output
before inserting the unit to the panel. Before starting to remove the unit
Note : , and parameters are shown, if the Temperature sensor analogue input type zone is formed below or around set value ON
3- Insert the mounting clamps to the fixing sockets from panel, power off the unit and
( 0/2..10V or 0/4..20mA ) is selected. and this zone is named hysteresis. Time
that located left and right sides of device and the related system. OFF
make the unit completely immobile within the ProNem Mini PMI-P Temperature and Humidity Sensor Input Connection Temperature Sensor Scale Selection Parameter ( Default = 0 ) Minimum Temperature Set Value Parameter ( Default = 10.0°C)
panel Analogue (Temperature) input range is determined with this parameter. Temperature set value can not be lower than this value. This parameter value can be
(1) (2) adjusted from minimum value of device scale to maximum temperature set value
3. Electrical Wiring Diagram 0..10V Z veya 0..20mA Z parameter
Temperature Sensor Input P/N : ESM-3723 - 5.6.6.0.1/01.01/1.6.6.0 (1) (2)
2..10V Z veya 4..20mA Z Maximum Temperature Set Value Parameter ( Default = 40.0 °C )
NTC, PTC, PT-100, 0/2..10V, 0/4..20mA 5A @250VV 3x3A@ 250V V 230 VV ± 15%
50/60Hz - 1.5VA Temperature Sensor Scale Low Limit Parameter : ( Default = 0 ) Temperature set value can not be greater than this value.
HEAT
or ProNem Mini PMI-P This parameter value can be adjusted from minimum temperature set value parameter
ALARM/
a
ALARM
12
HUM.
It can be adjusted from -1999 to ( -1). At this value analogue input becomes;
HEAT
Must be determined in order.
HUM.
GND
VCC
SDA
SCL
to maximum value of the device scale.
11
(1) (2)
Humidity Sensor Input If =0, according to the device type 0V Z or 0mA Z
10
0/2..10V, 0/4..20mA or 1 2 3 4 5 6 7 8 9 10 11 12 If
(1)
=1, according to the device type 2V Z or 4mA Z
(2)
Temperature Sensor Offset Parameter ( Default = 0 )
9
YELLOW
ProNem Mini PMI-P
BROWN
BLACK
GREEN
L
8
WHITE
Must be determined in order. N L From -10 to 10°C , NTC,PTC , PT-100 (0°C, 100°C)
N
7
Power Supply Voltage Temperature Sensor Scale High Limit Parameter : ( Default = 100 ) From -18 to 18°F, NTC,PTC , PT-100 (32°F, 212°F)
- +
6
P/N : ESM-3723
(1) (2)
According to the device type 10V Z or 20mA Z
14A T Fuse 50/60Hz - 1.5VA Shield From -18.0 to18.0°F NTC, PTC , PT-100 (32.0°F,212.0°F)
115VV( ±%15) 50/60Hz, L
4
Note : , parameters are shown, if the Temperature sensor analogue input type is selected . P ( -4°F, 176°F ),From -10.0 to 10.0°C, ProNem Mini PMI-P ( -20.0°C, 80.0°C ),
24VW ( ±%15) 50/60Hz ,
2
10...30 VZ 1.5 W Temperature Control Selection Parameter On/Off or PID ( Default = 0 ) From -18.0 to18.0°F, ProNem Mini PMI-P ( -4.0°F,176.0°F )
1
c
If this parameter select 1, parameter will be not observed.
Power Supply Input
Make sure that the power supply voltage is the same indicated on
the instrument. Auto Tune (Limit Cycle Tuning) Selection Parameter ( Default = ) Note : parameter ProNem Mini PMI-P type device are not observed.
Switch on the power supply only after that all the electrical Hysteresis Parameter for Humidity ( Default = 1 )
connections have been completed. Device does not do(Limit cycle Tuning) operation. From 1 to 10 for Humidity Sensor (0%RH, 100%RH)
N a L Supply voltage range must be determined in order. While installing
the unit, supply voltage range must be controlled and appropriate Device does operation. From 0.1to 10.0 for Humidity Sensor (0.0%RH,100.0%RH)
7 8 supply voltage must be applied to the unit. In ON/OFF control algorithm, Humidity Humidity
PID - Proportional Control Parameter ( Default =50 ) value is tried to keep equal to set value by
External
Note-1
Fuse This parameter value can be adjusted form 0 to 100. opening or closing the last control element.
c
(1A T) There is no power supply switch on the device. So a power supply ON/OFF controlled system, temperature hhSt hhSt
Supply
switch must be added to the supply voltage input. PID - Integral Parameter( Default = 1000 )
Switch value oscillates continuously. Temperature Set
Power switch must be two poled for seperating phase and neutral, This parameter value can be adjusted form 0 to 3600. value’s oscillation period or amplitude Time
c On/Off condition of power supply switch is very important in
electrical connection. PID - Derivative Parameter ( Default = 250 ) around set value changes according to
Control
External fuse that on Vpower supply inputs must be on phase
controlled system. For reducing oscillation Output
Supply Voltage This parameter value can be adjusted form 0 to 3600. period of temperature value, a threshold
230VV ( ±%15) 50/60Hz , connection. ON
115VV ( ±%15) 50/60Hz , PID -Period Time Parameter ( Default = 1 ) zone is formed below or around set value
External fuse that on Z power supply inputs must be on (+) Time
24VV( ±%15)50/60Hz , connection. This parameter value can be adjusted form 1 to 50 second. and this zone is named hysteresis.
24VW( ±%15) 50/60Hz ,
OFF
10...30 VZ 1.5 W
Must be determined in order.
Note-1: External Fuse is recommended
Note : Shield (Black) pin must be connected to number 10 (GND) of the terminal block. i (1) It is valid, if the device type 0/2...10V Z Temperature Sensor Input.
(2) It is valid, if the device type 0/4...20mA Z Temperature Sensor Input .
i (1) It is valid, if the device type 0/2...10V Z Humidity Sensor Input.
(2) It is valid, if the device type 0/4...20mA Z Humidity Sensor Input .
5 6 9 10
4.Front Panel Definition and Accessing to the Menus 5. Changing and Saving Temperature and Humidity Set Value Minimum Humidity Set Value Parameter (Default = Minimum Value of Device Scale) Humidity Alarm Set Parameter ( Default = 60 )
Humidity set value can not be lower than this value. This parameter value can be adjusted This parameter value can be programmed between humidity minimum alarm set
Main Operating Screen Temperature Set Value Screen from minimum value of device scale to maximum Humidity set value parameter parameter and humidity alarm set maximum parameter.
5 6 7 8 ESM-3723 ESM-3723
O1 O1 Maximum Humidity Set Value Parameter (Default = Maximum Value of Device Scale) Humidity Alarm Hysteresis Parameter ( Default = 0)
SET SET
Humidity set value can not be greater than this value. This parameter value can be This parameter value can be adjusted form 0 to %50 of the device scale.
ESM-3723
adjusted from minimum humidity set value parameter to maximum value of the
O1 O
C ü ü device scale. Humidity Alarm Set Minimum Parameter(Default =Minimum Value of Device Scale)
1 A1 O
F
SET
3 Humidity Sensor Offset Parameter ( Default = 0.0 )
if humidity alarm is active, this parameter value can be adjusted from minimum value of
device scale to humidty alarm set maximum parameter value.
O2 P From -10 to 10%RH for Humidity Sensor (0%RH-100%RH)
When SET button pressed ‘’S’’ led will Temperature set value can From -10.0 to 10.0%RH for Humidity Sensor (0.0%RH-100.0%RH) Humidity Alarm Set Maximum Parameter(Default =Maximum Value of Device Scale)
2 A2
ü 4 be active and temperature set value will
be displayed.
be changed with increment
and decrement buttons. Temperature Alarm Function Selection Parameter ( Default = 0 )
if humidity alarm is active, this parameter value can be adjusted from humidity alarm set
minimum parameter to maximum value of the device scale.
Temperature Set Value Screen Humidity Set Value Screen Temperature Alarm is inactive.
Humidity Alarm On Delay Time Parameter(Default = 0)
ESM-3723 ESM-3723
Process High alarm selected. Humidity Alarm On Delay Time can be defined with this parameter. It can be adjusted
9 10 11 12 Process Low alarm selected.
from 0 to 99 minutes.
SET SET
Humidity Alarm Delay After Power On Parameter(Default = 0)
BUTTON DEFINITIONS
Deviation Band alarm selected. When power is first applied to the device, this time delay must be expired for activation of
1. Increment Button :
ü ü Humidity alarm. It can be adjusted from 0 to 99 minutes.
** In main operation screen, press this button to change display temperature and humidity sensor Deviation Range alarm selected.
value. Buzzer Function Selection Parameter( Default = 0 )
** It is used to increase the value in the Temperature and Humidity Set screens and Programming mode. Note : If this parameter is select 0, Temperature Alarm parameters , , , , and Buzzer is inactive.
When SET button pressed Goes Humidity SET
2. Decrement, Silencing Buzzer Button : will be not observed.
temperature set value can be saved. value screen. Buzzer is active during temperature alarm
** It is used to decrease the value in the Set screen and Programming mode.
** It is used to silence the buzzer. Humidity Set Value Screen Humidity Set Value Screen Temperature Alarm Set Parameter ( Default = 50.0 °C ) Buzzer is active during humidity alarm
3. Set Button: This parameter value can be programmed between temperature minimum alarm set
** In the main operation screen; if this button pressed for the first time, Temperature set value will be ESM-3723 ESM-3723
parameter and temperature alarm set maximum parameter. Buzzer is active during Temperature sensor failures.
displayed. Value can be changed using increment and decrement buttons. When Enter button is 5.1 Changing and Saving Humidity Set Value
SET SET
Temperature Alarm Hysteresis Parameter ( Default = 0) Buzzer is active during Humidity sensor failures.
pressed again, value is saved and Humidty set value will be displayed next. Value can be changed using This parameter value can be adjusted form 0 to %50 of the device scale.
increment and decrement buttons. When Enter button pressed again, value is saved and returns back Buzzer is active during Temperature sensor failures or temperature alarm.
to main operating screen. ü ü Alarm Set Minimum Parameter (Default = Minimum Value of Device Scale)
Buzzer is active during Humidity sensor failures or Humidity alarm.
4.Enter Button: if temperature alarm is active, this parameter value can be adjusted from minimum value of
** To access the programming screen; in the main operation screen, press and hold this button for 5 device scale to temperature alarm set maximum parameter value. Buzzer is active during Temperature sensor failures or Humidity sensor failures
Humidity set value can be When SET button pressed Humidity
seconds. Alarm Set Maximum Parameter ( Default = Maximum Value of Device Scale)
changed with increment set value can be saved. Buzzer is active during Temperature sensor failures or Humidity sensor failures
** It is used to save value in the Set screens (Temperature or Humidity) and programming screen. if temperature alarm is active, this parameter value can be adjusted from temperature
and decrement buttons. or temperature alarm or humidity alarm.
alarm set value parameter to maximum value of the device scale.
LED DEFINITIONS Main Operating Screen Buzzer Active Time ( Default = )
Temperature Alarm On Delay Time Parameter ( Default = 0)
5.A1 led : If buzzer function selection parameter value = 0, this parameter is not observed.
ESM-3723 Temperature Alarm On Delay Time can be defined with this parameter. It can be
** It is active when Temperature alarm statuses. Buzzer active time can be define with this parameter. It can be adjusted from 1 to 99
adjusted from 0 to 99 minutes.
6. O1 Led : SET minutes. When this parameter is 1, if decrement button is pressed, is observed. In
** This led indicates that heating output is active. Temperature Alarm Delay After Power On Parameter ( Default = 0) this condition buzzer is active till buzzer silence button is pressed.
7.Celcius led : When power is first applied to the device, this time delay must be expired for activation of
ü temperature alarm. It can be adjusted from 0 to 99 minutes.
Button Protection Parameter ( Default = 0 )
** Indicates that device is in oC mode.
There is no protection.
8.Fahrenheit led : Humidity Alarm Function Selection Parameter ( Default = 0 )
** Indicates that device is in oF mode. Temperature set value can not be changed.
Goes back to main operation screen. Humidity Alarm is inactive.
9. O2 Led :
** This led indicates that Humidifier output is active. Humidity set value can not be changed.
Process High alarm selected.
10.A2 Led : Temperature set value and Humidity set value can not be changed
** This led indicates that Humidifier Alarm is active. Temperature set value parameter ( Default =50 °C ) Process Low alarm selected.
11.Precent Sign ledi : Temperature set value, can be programmed between minimum temperature set value and Programming Mode Accessing Password ( Default = 0 )
** Indicates that device is in Humidity Set screen or Humidifier output is active . maximum temperature set value . Deviation Band alarm selected. It is used for accessing to programming mode. It can be adjusted from 0 to 9999. If it is 0,
12.Program led : password is not entered for accessing to the parameters. When the password screen is not
Nem Set Parametresi (Default = 60%) Deviation Range alarm selected.
** Indicates that device is in programming mode . set as “12” , If the user enters ‘12’ in password screen and parameters are
Humidity set value, can be programmed between minimum Humidity set value and maximum
Note : If this parameter is select 0, Humidity Alarm parameters , , , , and accessed and they can changed.
temperature set value .
will be not observed.
If no operation is performed in Humidity set value changing mode and temperature set value
i changing mode for 20 seconds, device turns to main operation screen automatically.
7 8 11 12