Professional Documents
Culture Documents
Piping Material Specification
Piping Material Specification
``
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
01900-0004
B included in Description.
BI-10-
29SEPT16 BI-10-
Note for Fugitive Emission Class B as per ISO 15848-1 included in sour
and toxic (non-sour) pipe classes.
DATE
B
Note for temperature limitation for sleeve plug valve, lubricated plug
NO.
REV
DISCIPLINE
ENGINEER New pipe classes 1CS2P02, 1CX4P06, 1CX4P09, 1CX4P20, 1LE2P01,
NLP / SSK
1LE2W13, 1NT0A02, 1SD0P01, 1SX0P02, 3CT2P09 and 6SD0U01 are
29/09/2016
DATE: B added.
PROJECT
LEAD
ENGINEER
ENGINEER 00 Issued for Design
TNPRAG / RD
/ RAG
DATE:
29/09/2016 00 New pipe classes 1CH2C01, 1LE2P07, 3SD0U01.
CERTIFIED
PB / RSJ / KR 45 lateral connection branch table included in pipe classes 1CA2P06,
29/09/2016 00 1CA2P09, 1CH2P01, 1CT2P06, 1CT2P09, 1SD0P10.
DATE:
CONSTRUCTION
AGENCY Pipe Class 1CA2P06 and 1CA2P09 wall thickness for NPS 60 and NPS
00 64 is revised.
DATE:
OPERATIONS Design Conditions and size range revised based on latest process
00 inputs as marked in Appendix-1.
Fluid Category for pipe class 1LE2U01 from Category ‘D’ to ‘N’. NDE
EDSD
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
TABULATION OF HOLDS
ENGG CERT
RSJ
RSJ
PAGE /
DESCRIPTION OF HOLD
SECTION
RAG
RAG
01900-0004
BI-10-
29SEPT16 BI-10-
NO. DATE
REV
00
B
DISCIPLINE
ENGINEER
NLP / SSK
29/09/2016
DATE:
PROJECT
LEAD
ENGINEER
ENGINEER
TNPRAG / RD
/ RAG
29/09/2016
DATE:
CERTIFIED
PB / RSJ / KR
29/09/2016
DATE:
CONSTRUCTION
AGENCY
DATE:
OPERATIONS
DATE:
CONTROL NUMBER
VERIFICATION
EDSD
DATE:
BY:
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
TABLE OF CONTENTS
ENGG CERT
RSJ
RSJ
1. SCOPE 6
RAG
RAG
2. INTRODUCTION 8
2.2 Definition 8
2.4 Abbreviations 9
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
3.1 General 15
01900-0004
29SEPT16 BI-10-
00
B
DISCIPLINE
ENGINEER
NLP / SSK
3.6 Threads 18
29/09/2016
DATE:
PROJECT
3.7 Threaded Piping Systems 18
LEAD
ENGINEER
ENGINEER
RAG / RD
TNP / RAG
29/09/2016
3.8 Jointing Of Small Bore Pipes 19
DATE:
CERTIFIED
PB / RSJ / KR 3.9 Bends and Elbows in Small Bore Piping 19
29/09/2016
DATE:
CONSTRUCTION 3.10 Pressure 19
AGENCY
DATE:
3.11 Pipe 20
OPERATIONS
3.12 Pipes in Molten Sulfur Service 21
DATE:
3.13 Pipe Fittings 21
CONTROL NUMBER
VERIFICATION
EDSD
3.14 Gaskets 25
DATE:
3.15 Bolts 26
BY:
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
3.16 Fabrication 26
OF THIS DRAWING IS COVERED, FOR ALL
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
3.22 Valves 29
DESCRIPTION
3.26 Materials 34
JO/EWO
01900-0004
29SEPT16 BI-10-
00
B
DISCIPLINE
ENGINEER
NLP / SSK
4.1 Field Definition Tables 36
29/09/2016
DATE:
PROJECT
4.2 Valve Trim Number Designations 39
LEAD
ENGINEER
ENGINEER
RAG / RD
TNP / RAG
29/09/2016
5. LIST OF PROJECT & REFERENCE STANDARDS 39
DATE:
CERTIFIED
PB / RSJ / KR 5.1 Project Specifications and Standards 39
29/09/2016
DATE:
CONSTRUCTION 5.2 Industry Codes, Standards and Specifications 46
AGENCY
DATE:
APPENDIX 1 – PIPE CLASS SERVICE INDEX 56
OPERATIONS
64
VERIFICATION
EDSD
DATE:
BY:
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
1. SCOPE
ENGG CERT
The main objective of Fadhili Gas Program is to support Saudi Aramco’s corporate
RSJ
RSJ
strategy to meet In-Kingdom energy demand and reduce the burning of liquid fuel.
RAG
RAG
Fadhili Gas Plant (FGP) is a grassroots gas processing facility with a total capacity of
2,500 MMSCFD located approximately 30 km North West of Khursaniyah Gas Plant
and 80 km West of Jubail.
The plant processes 2000 MMSCFD of non-associated gas from the Hasbah (HSBH)
offshore fields and an additional 500 MMSCFD of gas from the Khursaniyah (KRSN)
DESCRIPTION
1,535 MMSCFD (based on heating value of 1,080 BTU/SCF) of sales gas from HSBH
gas feed.
470 MMSCFD of low BTU fuel gas from KRSN gas geed for use in an adjacent
Cogeneration plant.
JO/EWO
01900-0004
29SEPT16 BI-10-
The plant forms part of the larger overall Fadhili Gas Program being executed by
DATE
SAUDI ARAMCO.
NO.
REV
00
B
The Fadhili Gas Plant (FGP) consists of five gas processing trains, four of these trains
DISCIPLINE
ENGINEER will process Hasbah offshore gas and one train will process Khursaniyah onshore gas.
NLP / SSK
The FGP also includes six 800 MTD Sulfur Plants with tail gas treatment. The
29/09/2016
DATE: Technology Provider for the Sulphur Recovery Unit with Tail Gas Treatment is Shell
PROJECT
LEAD
ENGINEER
ENGINEER
Global Solutions International B.V.
TNPRAG / RD
/ RAG
DATE:
29/09/2016 The Fadhili Gas Plant will be executed as three EPC Contracts.
CERTIFIED
PB / RSJ / KR
29/09/2016
Packages as below:
DATE:
CONSTRUCTION
AGENCY Package 01 – Fadhili Gas Inlet & Treatment Facilities
Saudi Arabian Oil Company (Saudi Aramco + Aramco Overseas Company B.V.)
CONTROL NUMBER
VERIFICATION
Facilities.
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PIL scope for the contract includes Engineering, Procurement, Construction, Pre-
00
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
01900-0004
29SEPT16 BI-10-
00
B
DISCIPLINE
ENGINEER Primary and Secondary roads within designated area -
NLP / SSK
29/09/2016 Class 3 fence and outer patrol road around Sulfur
DATE:
PROJECT Handling Facility
LEAD
ENGINEER
ENGINEER
TNPRAG / RD
/ RAG Type –III Saudi Aramco fence system around West
DATE:
29/09/2016 CSW Ponds, Flare Stacks, gravity sewer sump and
CERTIFIED
PB / RSJ / KR
Evaporation ponds.
29/09/2016
DATE:
CONSTRUCTION
AGENCY
DATE:
OPERATIONS
DATE:
CONTROL NUMBER
VERIFICATION
EDSD
DATE:
BY:
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
2. INTRODUCTION
ENGG CERT
RSJ
RSJ
This document summarizes the piping material classes and covers the minimum
mandatory requirements for the material specifications for piping bulk components
and valves for new piping for use in Fadhili Gas Plant, Sulfur Recovery Facilities
Project, whose design is in accordance with ASME B31.3.
2.2 Definition
DESCRIPTION
Amine Services All Amine solutions including MEA, MDEA, DGA, and
ADIP
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
General Services Includes Piping Classes required for plants and facilities
in b o t h normal fluid services and Category D fluid
service as defined in ASME B31.3
JO/EWO
01900-0004
29SEPT16 BI-10-
00
B
DATE:
29/09/2016 Category M Services As defined in ASME B 31.3
PROJECT
LEAD
ENGINEER
ENGINEER
RAG / RD
Utility services: Includes plant air, nitrogen, steam, condensate, BFW
TNP / RAG
29/09/2016 etc. may be included for consolidation and reduction in
DATE:
CERTIFIED required Pipe classes only, additions subject to
PB / RSJ / KR COMPANY approval.
29/09/2016
DATE:
CONSTRUCTION
AGENCY
2.3 Plant Specific Abbreviations
AGE - Acid Gas Enrichment
DATE:
OPERATIONS
AGR - Acid Gas Removal
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
MDEA - Methyldiethanolamine
ENGG CERT
RSJ
RSJ
2.4 Abbreviations
AG Above Ground
01900-0004
BI-10-
29SEPT16 BI-10-
00
B
DISCIPLINE
ENGINEER
NLP / SSK
BAL Ball
29/09/2016
DATE:
PROJECT
LEAD
ENGINEER BB Bolted Bonnet
ENGINEER
TNPRAG / RD
/ RAG
DATE:
29/09/2016 BBE Bevel Both Ends
CERTIFIED
PB / RSJ / KR
BC Bolted Cap (Cover)
29/09/2016
DATE:
CONSTRUCTION
AGENCY BE Bevel End
BS British Standard
DATE:
BTF Butterfly
BY:
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
BW Butt Weld
OF THIS DRAWING IS COVERED, FOR ALL
CA Corrosion Allowance
(DCC) NO. _____________________
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
CALC Calculation
ENGG CERT
RSJ
RSJ
CHE Check
RAG
RAG
CL Class / Rating
CONC Concentric
CONN Connector
DESCRIPTION
CS Carbon Steel
CU Copper
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
DEG Degree
DI Ductile Iron
DGN Design
JO/EWO
01900-0004
29SEPT16 BI-10-
DATE
DWG Drawing
00
B
DISCIPLINE
ENGINEER
NLP / SSK DSS Duplex Stainless Steel
29/09/2016
DATE:
PROJECT ECC Eccentric
LEAD
ENGINEER
ENGINEER
TNPRAG / RD
/ RAG
29/09/2016
EFW Electric Fusion Welding
DATE:
CERTIFIED
PB / RSJ / KR ENP Electroless Nickel Plating
29/09/2016
DATE:
CONSTRUCTION EPC Engineering, Procurement and Construction
AGENCY
DATE:
EPDM Ethylene Propylene Diene Monomer
OPERATIONS
EXP SEAT Expanding Seat
DATE:
F6 Hard Facing (API STD 600 Table 3 Trim 1)
CONTROL NUMBER
VERIFICATION
EDSD
FB Full Bore
DATE:
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
FEM Female
OF THIS DRAWING IS COVERED, FOR ALL
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
FLG Flange
RAG
RAG
FLGD Flanged
FP Full Port
FS Fire Safe
DESCRIPTION
GALV Galvanised
GO Gear Operator
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
GR Grade
GRAF Grafoil
GRAPH Graphite
JO/EWO
01900-0004
BI-10-
29SEPT16 BI-10-
00
B
DISCIPLINE
HD Heavy Duty
ENGINEER
NLP / SSK
29/09/2016
HF Hard Faced
DATE:
PROJECT
LEAD
ENGINEER
ENGINEER
HIC Hydrogen-Induced Cracking
TNPRAG / RD
/ RAG
DATE:
29/09/2016
HYDRAU Hydraulic
CERTIFIED
PB / RSJ / KR
29/09/2016
HO Handwheel Operator
DATE:
CONSTRUCTION
AGENCY
ID Inside Diameter
DATE:
OPERATIONS I/O Inner Ring/Outer Ring
JF Joint Factor
DATE:
BY:
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
LJ Lamination Joint
ENGG CERT
RSJ
RSJ
LO Lever Operator
RAG
RAG
LR Long Radius
LT Low Temperature
DESCRIPTION
MAT Material
MAX Maximum
JO/EWO
01900-0004
29SEPT16 BI-10-
DATE
00
B
DISCIPLINE
MIN Minimum
ENGINEER
NLP / SSK
29/09/2016
MP Medium Pressure Steam
DATE:
PROJECT
LEAD
ENGINEER
ENGINEER MSD Material Selection Diagram
TNPRAG / RD
/ RAG
29/09/2016
DATE: NACE National Association of Corrosion Engineers
CERTIFIED
PB / RSJ / KR
OD Outside Diameter
DATE:
CONTROL NUMBER
VERIFICATION
ORIF Orifice
DATE:
BY:
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
PE Plain End
ENGG CERT
RSJ
RSJ
PP Polypropylene
RAG
RAG
PRESS Pressure
R Radius
JO/EWO
01900-0004
29SEPT16 BI-10-
REV Revision
DATE
RF Raised Face
NO.
REV
00
B
DATE:
29/09/2016
SAEP Saudi Aramco Engineering Procedure
CONSTRUCTION
AGENCY
SAIP Saudi Aramco Inspection Procedure
DATE:
OPERATIONS SAMSS Saudi Aramco Materials System Specification
SB Screwed Bonnet
EDSD
SC Screwed Cap
DATE:
BY:
SCH Schedule
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
SCRD Screwed
(DCC) NO. _____________________
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
SMLS Seamless
ENGG CERT
RSJ
RSJ
SO Slip-On Flange
RAG
RAG
SR Short Radius
SS Stainless Steel
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
STD Standard
ISSUED FOR DESIGN
STL Steel
STELL Stellite 6
STR Strainer
JO/EWO
01900-0004
BI-10-
29SEPT16 BI-10-
SW Socket Weld
DATE
00
B
DISCIPLINE
TBE Threaded Both Ends
ENGINEER
NLP / SSK
29/09/2016
TEG Tri-Ethylene Glycol
DATE:
PROJECT
LEAD
ENGINEER
ENGINEER TEMP Temperature
TNPRAG / RD
/ RAG
29/09/2016
DATE: TF Taper Female
CERTIFIED
PB / RSJ / KR
TR Trim
CONTROL NUMBER
VERIFICATION
EDSD
UB Union Bonnet
DATE:
BY:
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
WT Wall Thickness
ENGG CERT
RSJ
RSJ
WDG Wedge
RAG
RAG
WLDD Welded
WN Weld Neck
WO Wrench Operator
XS Extra Strong
DESCRIPTION
01900-0004
BI-10-
29SEPT16 BI-10-
Piping systems, and all piping components, shall be designed and fabricated in
accordance with ASME B31.3-2012 edition and the relevant ASME Codes (where
DATE
00
B
DISCIPLINE
ENGINEER
NLP / SSK The limits of piping governed by codes other than ASME B31.3 shall be indicated
DATE:
29/09/2016 on the P&IDs. Each Pipe Class shall indicate the applicable ASME piping design
PROJECT
LEAD
code.
ENGINEER
ENGINEER
TNPRAG / RD
/ RAG
29/09/2016 For pipe classes identified as “LETHAL” in Pipe Class Service Index (Appendix 1)
DATE:
CERTIFIED shall be considered as Category M services and shall be designed to ASME
PB / RSJ / KR B31.3. Chapter VIII requirements.
29/09/2016
DATE:
CONSTRUCTION This document is to be read in conjunction with COMPANY Specifications,
AGENCY
Standards, Standard Drawings, Commodity Code Description and Codes and
DATE:
Regulations which also apply including Project specific amendments. In the
OPERATIONS event of any conflict of information, CONTRACTOR shall seek written
clarification from COMPANY before proceeding. Material selection and
corrosion control requirements shall comply with COMPANY standards and,
DATE:
where applicable, licensor standards.
CONTROL NUMBER
VERIFICATION
Charpy impact testing shall be carried out on all carbon steel pipes and wrought
EDSD
greater than 25mm (Min. temp for carbon steel Pipe Class set at 32 deg F
BY:
(0 deg.C)). Testing shall be in accordance with ASME B31.3 with impact values
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
being 34J min average and 27J min individual for a standard 10mm x 10mm
CERTIFICATE
specimen. Impact testing shall be carried out on the base metal, weld deposit
(DCC) NO. _____________________
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
Impact testing for Low Temperature Carbon Steel (LTCS) pipes (ASTM A333 and
ENGG CERT
RSJ
RSJ
A671) and wrought fittings (ASTM A420) shall be carried out in accordance with
applicable ASTM standard. For ASTM A671 pipes, impact testing as per
RAG
RAG
All material in wet sour service shall meet the requirements of SAES-L-133, 01-
SAMSS-016 & NACE MR0175/ISO 15156 and the Project Material selection guide
DESCRIPTION
(licensor unit), report (non Licensor units) & MATERIAL REQUIREMENT FOR CS
AND LOW ALLOY STEEL (RE-380920).
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
Pipe classes with wet sour service requirement are identified as NACE
MR0175/ISO 15156 in Appendix 1, Pipe Class Service Index.
01900-0004
(SOHIC), and Hydrogen Blistering are all mechanisms associated with hydrogen-
BI-10-
29SEPT16 BI-10-
All material for use in wet, sour services described in SAES-L-133, paragraph
NO.
REV
00
DISCIPLINE
ENGINEER SAES-L-133 paragraph 7.2.2.
NLP / SSK
DATE:
29/09/2016
Design sour gas in-plant piping systems and pipelines for resistance to SOHIC by
PROJECT
LEAD
ENGINEER observing the restrictions in SAES-L-136. Note that steels and weldments that
ENGINEER
TNPRAG / RD
/ RAG are resistant to HIC may be susceptible to SOHIC. To prevent SOHIC, welded
DATE:
29/09/2016 pipe (e.g. straight or spiral seam), shall not be used in sour gas unless it is stress
CERTIFIED relieved by heat treatment (see SAES-L-136)
PB / RSJ / KR
29/09/2016
DATE: The following should be considered to achieve HIC resistance in carbon steels:
CONSTRUCTION
AGENCY
1. Low Sulfur and phosphorous contents
DATE:
OPERATIONS 2. Vacuum degassing
DATE:
3. Low oxygen
CONTROL NUMBER
VERIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
The individual piping classes specify the amount of corrosion allowance included
in the pipe wall and fitting schedules.
and the relevant ASME Codes (where applicable) together with SAES-L-100,
SAES-L-105, SAES-L-310, and SAES-L-610.
All pressure – temperature ratings for flanged components are in accordance with
ASME B16.5 and ASME B16.47 Series A, Pipe Flanges and Flanged Fittings.
Other components are selected for the required ratings in accordance with the
standards to which they are manufactured.
JO/EWO
01900-0004
BI-10-
29SEPT16 BI-10-
All pressure and temperature limits shown in the Piping Classes are design
conditions and are not to be exceeded without making appropriate materials
DATE
changes.
NO.
REV
00
B
All pipe and fittings shall have the material specification and grade stamped,
DISCIPLINE
ENGINEER stenciled, or otherwise clearly marked with permanent marking method as per
NLP / SSK
individual pipe or fitting specification.
29/09/2016
DATE:
PROJECT
LEAD
ENGINEER Colour coding shall be applied as per 00-SAIP-07, SAES-A-206 and SAES-B-
ENGINEER
TNPRAG / RD
/ RAG 067.
29/09/2016
DATE:
CERTIFIED
PB / RSJ / KR
Utility Stations: The water, steam, air and nitrogen lines shall be marked and
29/09/2016
colour coded as specified in SAES-L-310.
DATE:
CONSTRUCTION
AGENCY 3.5 Service Limits and Pipe Wall Thickness
DATE:
Pipe wall thicknesses determined by contractor for individual Pipe Classes are
OPERATIONS suitable for the complete range of pressure/temperature limit combinations as
tabulated on Appendix 1 and additionally include the indicated corrosion
allowance together with requirements as specified in SAES-L- 310.
DATE:
Pipe Wall Thicknesses are as per Pipe Wall Thickness Calculations, Doc. No.
CONTROL NUMBER
VERIFICATION
D44-A-RE-589197.
EDSD
Note: For Carbon Steel Piping, the minimum nominal wall thickness shall not be
DATE:
less than the values listed in Table 2 of SAES-L-310 – Design of Plant Piping
BY:
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
stated on Appendix 1.
(DCC) NO. _____________________
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
Pipe wall thickness calculated in accordance with the Design Code referred
above. Where full vacuum design conditions are stated for a Pipe Class in the
ENGG CERT
RSJ
RSJ
The mill tolerances are selected corresponding to the material standards API
/ASTM.
Mill tolerance for fittings mating with ASTM A671 pipes (NPS 26 and above) shall
DESCRIPTION
Mill tolerance for fittings mating with ASTM A358 pipes (NPS 14 and above) shall
be as defined in ASTM A358.
In case of tie-ins the pipe wall thickness shall be verified and matched with
existing tie-in pipe wall thicknesses, where specifically called out in the Material
Selection Diagram.
JO/EWO
01900-0004
BI-10-
29SEPT16 BI-10-
Temperature and pressure limits shown in each Piping Class are design
condition and are not to be exceeded without prior approval of Company
DATE
Representative in writing. “Rating B16.5” indicates that the design condition of the
piping system are still within the pressure and temperature limits established by
ASME/ANSI B16.5 standard, Table “2” (showing the maximum no-shock working
NO.
REV
00
B
DATE:
29/09/2016 Pipe wall thickness for RTR/PVDF pipe classes shall be provided by RTR/PVDF
PROJECT
LEAD
vendors, based on vendor’s manufacturing standards.
ENGINEER
ENGINEER
TNPRAG / RD
/ RAG
DATE:
29/09/2016 3.6 Threads
CERTIFIED
PB / RSJ / KR
All screwed connections shall have taper threads in accordance with ASME
29/09/2016
B1.20.1 (NPT), and be limited to NPS 1.1/2” (2” maximum where required for
DATE:
CONSTRUCTION
maintenance) in hazardous services. For non-hazardous services threaded
AGENCY connections shall be in accordance with SAES-L-110 para 7.
DATE:
3.7 Threaded Piping Systems
OPERATIONS
As a general design policy to reduce the incidence of leakage, the use of
DATE:
threaded joints and unions (where permitted by the Pipe Class) shall be kept to a
minimum, consistent with ease of pipe work fabrication, installation and
CONTROL NUMBER
VERIFICATION
maintenance.
EDSD
Threaded joints shall be kept to a minimum and shall be seal welded according to
DATE:
glasses, level alarms and controllers, etc.), control, relief, and sampling valves,
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
pumps and other mechanical equipment, screwed plugs in drain and vent valves,
OF THIS DRAWING IS COVERED, FOR ALL
and atmospheric vent and drain connections downstream of last isolation valve.
(DCC) NO. _____________________
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
Threaded joints shall not be used in sour service except for hydrotest vents
and/or drains and orifice flange taps.
ENGG CERT
RSJ
RSJ
All threaded connections that require seal welding, shall meet the requirements
RAG
RAG
Threaded plugs on hydrostatic vents, not provided with a valve, shall be seal
welded after testing has been carried out.
Joint for seal weld shall be assembled dry without sealing compounds or tape.
DESCRIPTION
400 deg F (204 deg C) & below – use PTFE Jointing Tape, or approved jointing
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
compound.
Above 400 deg F ( 204 deg C) – Seal weld wherever possible, otherwise seek
clarification from COMPANY to use jointing compound to manufacturer’s
standards.
JO/EWO
01900-0004
29SEPT16 BI-10-
With the exception of galvanized piping, straight lengths of small bore piping NPS
DATE
00
reducers, caps, etc. and valves, flanges, shall be socket welded wherever SW is
B
DISCIPLINE
ENGINEER
permitted as per Appendix 1.
NLP / SSK
29/09/2016
DATE: 3.9 Bends and Elbows in Small Bore Piping
PROJECT
LEAD
ENGINEER
ENGINEER
RAG / RD
In small bore welded piping NPS 2” and smaller, hot or cold formed bends with a
TNP / RAG
29/09/2016
radius of 5D (Nominal Diameter) min. are permitted except in Sour Services
DATE:
CERTIFIED
unless otherwise stated. The maximum permissible ovality after bending is 5%
PB / RSJ / KR on outside diameter. The maximum permissible thinning on the back of the bend
DATE:
29/09/2016 shall be 12½% of nominal wall thickness.
CONSTRUCTION Long radius elbows, 1½D, shall be used for 2"NPS and below unless otherwise
AGENCY
stated in Project documentation. It shall be determined whether a 5D bend is
required for process reasons, e.g. to reduce pressure drop, abrasive service etc.
DATE:
OPERATIONS in accordance with SAES-L-105, SAES-L-136, 01-SAMSS-039, all applicable
Saudi Aramco and Project Specifications.
DATE:
3.10 Pressure
CONTROL NUMBER
VERIFICATION
All pressures given in this standard are gauge pressure, unless otherwise stated.
EDSD
Pressure testing for all plant piping is to be in accordance with applicable ASME
REVISIONCERTIFICATION
code, SAES-A-004, SAES-L-150 and all other pertinent specifications and design
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
practices mentioned therein. Lube and Seal Oil is to be tested with its own fluid.
00
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
Pressure testing of fire water piping shall be as per SAES-B-017, clause 12.6.
ENGG CERT
RSJ
RSJ
3.11 Pipe
All pipes shall comply with COMPANY technical requirements in accordance with
RAG
RAG
Minimum pipe size shall be NPS ¾” unless stated otherwise in the individual Pipe
DESCRIPTION
Classes. Smaller sizes may be permitted for instrument connections and steam
tracing etc., only where specifically stated.
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
Non-standard pipe sizes are NPS 1/8”, ¼”, 3/8”, 1¼”, 2½”, 3½”, 5”, 7” & 9” and
ISSUED FOR DESIGN
22” shall not be used in any Pipe Class, except where specifically shown on
P&IDs.
For nominal pipe sizes greater than NPS 24”. Pipe sizes shall, wherever possible,
increase in increments of 6 inches up to and including NPS 48”. Above NPS 48”,
nominal pipe sizes shall increase in increments of 4 inches.
JO/EWO
01900-0004
29SEPT16 BI-10-
Pipe sizes not included in ASME B36.10 / B36.19 shall not be used (unless
DATE
00
B
Carbon steel and low temperature carbon steel pipe shall be seamless up to and
DISCIPLINE
ENGINEER including NPS 24” and SAW / EFW for Pipes larger than NPS 24”.
NLP / SSK
29/09/2016
DATE: API 5L pipe a n d all other welded carbon steel pipe shall be 100% radiographed
PROJECT
LEAD
ENGINEER and have a joint factor of 1.
ENGINEER
TNPRAG / RD
/ RAG
DATE:
29/09/2016 Low Alloy Steel pipe (2.1/4 Cr-1Mo) shall be seamless up to and including NPS
CERTIFIED
PB / RSJ / KR
16 and SAW/EFW for Pipes larger than NPS 18 with 100% radiography and joint
29/09/2016
factor of 1.0.
DATE:
CONSTRUCTION
AGENCY Stainless steel pipes Series 300 (e.g. SS304/304L or SS316/316L), Duplex SS,
6Mo (254 SMO SS) shall be seamless up to and including NPS 12” and EFW
DATE: for pipes NPS 14” and larger, together with 100% radiography and joint factor of
OPERATIONS
1.0.
DATE:
CS/LTCS pipe sizes 1-1/2" & smaller Single random length (5 to 7m)
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
CS/LTCS pipe sizes 2" to 48” Double random lengths (11 to 13m)
00
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
Note: Where equipment is supplied with non-standard nozzle sizes, these shall
be adjusted to a standard size by means of a reducing fitting immediately
DESCRIPTION
All buried steel pipe shall be externally protected against corrosion per
Project Specification For External Coating (D44-H-RE-380909) and COMPANY
Specification SAES-H-002.
01900-0004
BI-10-
29SEPT16 BI-10-
00
B
DISCIPLINE
ENGINEER
NLP / SSK
a) Minimum Corrosion Allowance 3.2mm
29/09/2016
DATE:
PROJECT
b) Maximum Corrosion Allowance 6.4mm
LEAD
ENGINEER
ENGINEER
RAG / RD
TNP / RAG
For Jacketed Lines
29/09/2016
DATE:
CERTIFIED
PB / RSJ / KR a) Minimum Corrosion Allowance 6.4mm
29/09/2016
DATE:
CONSTRUCTION
3.13 Pipe Fittings
AGENCY
All pipe fittings shall comply with COMPANY technical requirements in
DATE: accordance with SAES-L-105, all appropriate listed Specifications and Standard
OPERATIONS Drawings, including Project specific amendments.
DATE:
Pipe Classes where more than one class of socket weld fitting is listed, such as
class 3000 and class 6000, reducing fittings shall be specified to the higher rating
CONTROL NUMBER
VERIFICATION
Socket weld or threaded fitting shall not be used in sour service. Butt-weld fittings
DATE:
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
Butt-weld elbows shall be long radius (R=1.5D). Short radius elbows are non-
OF THIS DRAWING IS COVERED, FOR ALL
preferred and used only where required due space limitation. Company approval
(DCC) NO. _____________________
is required for their use. Mitered, reduced and street elbows (one end female
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
Carbon steel and low temperature carbon steel butt weld fittings shall be
RAG
RAG
seamless up to and including NPS 24”. Fittings greater than NPS 24” shall be
EFW with 100% radiography of weld seam and joint efficiency factor of 1.0.
Low Alloy Steel fittings (2.1/4 Cr-1Mo) shall be seamless up to and including NPS
16 and SAW/EFW for Fittings larger than NPS 18 with 100% radiography and
joint factor of 1.0.
DESCRIPTION
Stainless steel butt weld fittings Series 300 (e.g. SS304/304L or SS316/316L),
Duplex SS, 6Mo (254 SMO SS) shall be seamless up to and including NPS
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
12”. Fittings greater than NPS 14” shall be EFW with 100% radiography of weld
ISSUED FOR DESIGN
Unless otherwise stated, the minimum end wall thickness of butt welded fittings
shall be equal to the thickness of the connected pipe.
All piping components of 304L and 316L Stainless Steel shall have the
mechanical properties in accordance with the straight grade and with the
JO/EWO
01900-0004
chemical composition in accordance with the low grade, i.e.., be “Dual Certified”
BI-10-
29SEPT16 BI-10-
DATE
00
B
DATE:
29/09/2016 3.13.2 Nipples
PROJECT
LEAD
ENGINEER
ENGINEER The minimum wall thickness for Nipples to allow for increased mechanical
RAG / RD
TNP / RAG
strength shall be:
29/09/2016
DATE:
CERTIFIED
PB / RSJ / KR Carbon and low alloy steels Sch 80
29/09/2016 Stainless steels Sch 40S
DATE:
CONSTRUCTION
Galvanised steel (threaded) Same as pipe schedule
AGENCY
In vibrating service where bracing cannot be effectively provided, Sch.160
DATE: minimum nipples for carbon steel piping systems.
OPERATIONS
3.13.3 Unions
DATE:
Unions may only be used where indicated on Pipe Classes; they shall not be
CONTROL NUMBER
VERIFICATION
used in:
EDSD
Hydrogen service
DATE:
BY:
Steam service
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
Hot or cold formed bends NPS 3” and larger, having radii of 2” x NPS or greater,
shall comply with CONTRACTOR’s technical requirements for the supply of pipe
bends which shall be reviewed by COMPANY with particular reference to wall
DESCRIPTION
3.13.5 Flanges
ISSUED FOR DESIGN
Flanges up to and including NPS 24” shall be in accordance with ASME B16.5
JO/EWO
01900-0004
. Flanges NPS 26” & above, shall be in accordance with ASME B16.47,
BI-10-
29SEPT16 BI-10-
series A (MSS SP 44) unless otherwise stated. Flanges not covered by the
DATE
00
B
DISCIPLINE
these cases the Flange standard and rating shall be ascertained from Site
ENGINEER
NLP / SSK
supplied data and / or field verification.
29/09/2016
DATE:
PROJECT
The thickness of Blind Flanges to NPS 26” & larger shall conform to ASME
LEAD
ENGINEER
ENGINEER
B16.47, series A (MSS SP 44) unless otherwise stated.
RAG / RD
TNP / RAG Blind Flanges not covered by the above shall be designed and fabricated
29/09/2016
DATE: according to ASME VIII, div. 1.
CERTIFIED
PB / RSJ / KR
29/09/2016 Slip-on flanges may be used in utility services and as out-of-spec flanges with
DATE:
CONSTRUCTION
COMPANY’s written approval provided that the following limitations are met:
AGENCY
a) Shall not be used for temperatures above 752 deg F (400 deg C).
DATE:
OPERATIONS
b) Shall not be used when the corrosion allowance is above 3.0 mm.
c) Shall not be used in cases where large temperature cycles can occur.
DATE:
d) Shall not be used in classes 600lb or higher.
e) Shall not be attached directly to pipe fittings.
CONTROL NUMBER
VERIFICATION
flanges.
BY:
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
Flange facing finish shall be per SAES-L-109 unless otherwise stated. Ring joint
(DCC) NO. _____________________
flanges shall be used in all classes rated 900lb and above. Unless specified in
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
individual Pipe Classes, flat faced flanges shall only be used when mating to cast
iron, bronze or non-metallic flanges or to flat face flanges on equipment. Flat face
ENGG CERT
RSJ
RSJ
The flange finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to
6.3 micro-metres) Ra per ASME B46.1 except otherwise stated.
Special PIKOTEK gasket can be used with raised-face, flat face and RTJ flanges
of varying configurations in all pressure classes.
Blind flanges which may require boring shall be limited to NPS 4” and above. For
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
blind flanges requiring tapping or boring less than NPS 4”, qualification in acc.
ISSUED FOR DESIGN
with ASME SEC.VIII, Div.2 shall be submitted for review and acceptance by
the Chairman, piping standard committee as stated in SAES-L-109.
Spectacle Blinds shall be used for all isolation, pipe sizes and flange ratings and
shall comply with Saudi Aramco Standard Drawings. Spectacle Blinds not
covered by the above Standard Drawings and non-ferrous material shall be
JO/EWO
01900-0004
designed and fabricated in accordance with ASME B16.48. In flanged joints using
BI-10-
29SEPT16 BI-10-
a spectacle blind, one flange shall be fitted with jackscrews as per Saudi Aramco
DATE
Drawing AC-036630.
00
B
DISCIPLINE
SPACERS and BLANKS by developing a new SA-175-special reflecting the
ENGINEER
NLP / SSK
requirements of standard drawing AD-036633, 02-SAMSS-011 & SAES-W-011.
29/09/2016 The following shall be captured as a minimum within the new SA -175:
DATE:
PROJECT
LEAD
ENGINEER
ENGINEER
RAG / RD
Company approval of NDT Personnel and Procedures to 02-SAMSS-
TNP / RAG
29/09/2016
011, SAES-W-011 and ASME V
DATE:
CERTIFIED
PB / RSJ / KR If spectacle plate is constructed by welding:
29/09/2016
DATE:
CONSTRUCTION o Company approval of Welding Procedure Specification (WPS)
AGENCY
and Procedure Qualification Records (PQR) to SAES-W-011
and ASME IX
DATE:
OPERATIONS
o Full Penetration Welding achieved
ASME Sec V
EDSD
DATE:
BY:
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
spacer and
ISSUED FOR DESIGN
spade
1. Spades for line size ≥12 inches for all piping classes shall be installed in a
horizontal pipe run with the spade in the vertical position.
JO/EWO
01900-0004
29SEPT16 BI-10-
due to freezing. A ring spacer and spade shall be used for this service for
DATE
3.14 Gaskets
NO.
REV
00
B
DISCIPLINE
ENGINEER
All gaskets shall comply with COMPANY technical requirements in accordance
NLP / SSK with SAES-L-109, all listed specification and standard drawings, including any
DATE:
29/09/2016
Project specific amendments.
PROJECT
LEAD
ENGINEER
ENGINEER
TNPRAG / RD
/ RAG RTJ gaskets, when specified shall comply with SAES standard SAES-L-109.
29/09/2016
DATE:
CERTIFIED “Flexible Graphite” compounds shall contain min.98% pure Carbon, leachable
PB / RSJ / KR
chlorides of 50ppm max. and total sulphur of 500ppm max., except where
29/09/2016
DATE: specific Service requirement is determined otherwise.
CONSTRUCTION
AGENCY
For design temperature above 752 Deg F (400 Deg.C), in spiral wound gasket,
DATE: suitable gasket filler material such as combination of mica layers and graphite
OPERATIONS fillers or equivalent shall be used or as defined by the Process Licensor.
DATE:
Spiral wound gaskets shall be used with raised face flanges.
Spiral wound gaskets shall be with inner ring of SS316L as a minimum or
CONTROL NUMBER
VERIFICATION
equivalent to base piping class material grade and outer ring in carbon steel
EDSD
connect by flange (such as copper alloy or stainless steel to carbon steel where
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
the potential for galvanic corrosion exists), insulating gasket PIKOTEK type or
OF THIS DRAWING IS COVERED, FOR ALL
approved equal with isolating sleeves and washers shall be used as per SAES-L-
(DCC) NO. _____________________
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
Compressed fiber, asbestos-free gaskets shall be limited to water and air service.
ENGG CERT
RSJ
RSJ
Elastomeric material shall only be used with plastic flanges, flat faced. Composite
flat gasket, PIKOTEK or approved equal, may be used in place of soft iron ring
RAG
RAG
3.15 Bolts
All bolting shall comply with the technical requirements in accordance with SAES-
L-109, all listed specifications and standard drawings, including any Project
specific amendments. Bolts, studs and nuts shall be threaded according to ASME
DESCRIPTION
Where their lengths shall be in metric and diameter shall be in imperial unit
system. Metric lengths shall be in 5 mm increments.
Bolting shall be ceramic / fluoropolymer coated or Hot dip galvanized as per D44-
H-RE-380909, clause 7.5 and 09-SAMSS-107.
01900-0004
29SEPT16 BI-10-
DATE
All jackscrews and hexagonal head bolt shall have threads extended to underside
of the head.
NO.
REV
00
B
Bolt tensioning shall also be applied when critical joints have been identified (e.g.
DATE: cyclic service etc.) and when criticality code is indicated in the unit Stress Critical
CONTROL NUMBER
Line List.
VERIFICATION
EDSD
3.16 Fabrication
DATE:
SAES-L-350.
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
Branch connections and their reinforcement shall not cover the girth weld and
reinforced pad shall be of the same pipe material.
DESCRIPTION
Positive Material Identification (PMI) shall be carried out on all pressure retaining
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
alloy material components, flange bolting, welds and welding overlays to ensure
ISSUED FOR DESIGN
that nominal composition of the alloy has been correctly supplied and installed.
01900-0004
temperature.
BI-10-
29SEPT16 BI-10-
Pneumatic test shall be carried for the lines as proposed in Technical Query raised
DATE
00
B
DISCIPLINE
ENGINEER
NLP / SSK For Hydrostatic Testing of 300 type Stainless Steels, water with very low chloride
DATE:
29/09/2016 content (less than 50ppm) shall be used in order to avoid pitting and stress
PROJECT corrosion cracking.
LEAD
ENGINEER
ENGINEER
TNPRAG / RD
/ RAG
29/09/2016
Installation of plastic piping shall be done by personnel trained in the proper
DATE:
CERTIFIED
handling and usage of applicable materials and equipment prior to the start of
PB / RSJ / KR installation. Assembly of RTR (Reinforced Thermosetting Resin) piping shall be
DATE:
29/09/2016 of “restrained” type (adhesive-bonded, butt and wrap or mechanical) and heating
CONSTRUCTION blankets shall be used to cure adhesive bonded joints. Adhesive (for RTR piping),
AGENCY
solvent cement and primer (for CPVC Chlorinated Polyvinyl Chloride piping) shall
be used within the manufacturer’s expiry date on the label. Heating blankets shall
DATE:
OPERATIONS be used to cure RTR adhesive bonded joints. Flat washers shall be used
under nuts and bolts heads on non-metallic flanges.
DATE:
3.17 Post Weld Heat Treatment (PWHT)
CONTROL NUMBER
VERIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
Street tees (one end female threaded, the other end male threaded) are not
permitted. Stub-Ins (with or without reinforcement) shall be in accordance with
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
code.
Pipe plugs for use in steel piping shall be solid-body, round stock or forged. Fittings
standards shall be in accordance as per the following table:
01900-0004
29SEPT16 BI-10-
00
B
DISCIPLINE
90 deg SR (Short Radius) Elbows ASME 16.28 02-SAMSS-005(*)
ENGINEER
NLP / SSK Swaged Nipples BS 3799 None
29/09/2016
DATE:
PROJECT (*) CS/LTCS only (**) Such as Thredolet, Weldolet, etc.
LEAD
ENGINEER
ENGINEER
TNPRAG / RD
/ RAG
29/09/2016
3.19 Standard Sub-Assemblies
DATE:
CERTIFIED
PB / RSJ / KR
Vent, drain, instrument connections and utility stations standard assembly
29/09/2016
drawings shall be developed by the CONTRACTOR and included in the Piping
DATE: Material Specification. These Standard Drawings should incorporate components
CONSTRUCTION
AGENCY from the appropriate Pipe Class and in addition conform to requirements of
COMPANY Standards including any Project specific amendments.
DATE:
OPERATIONS
3.20 Special Piping Items
All special piping items shall comply with COMPANY Standards and standard
DATE:
drawings including any Project specific amendments. Items shall be listed,
CONTROL NUMBER
VERIFICATION
identified, procured and installed fully in accordance with all relevant process and
piping standards. Installation shall conform to Manufacturer’s recommendations.
EDSD
DATE:
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
RAG
RAG
3.22 Valves
All valves shall comply with COMPANY technical requirements in accordance
with SAES-L-105, SAES-L-108 and all listed specifications and standard
drawings, including any Project specific amendments. These shall include, but
not limited to the following:
01900-0004
29SEPT16 BI-10-
00
B
DATE:
29/09/2016 04-SAMSS-047 Steel High Performance Butterfly Valves (Including
PROJECT
LEAD
ENGINEER
Triple-Offset)
ENGINEER
TNPRAG / RD
/ RAG
DATE:
29/09/2016 04-SAMSS-048 Valve Inspection and Testing Requirements
CERTIFIED
PB / RSJ / KR
04-SAMSS-050 Gate Valves, Through Conduit Type, API SPEC 6D
29/09/2016
DATE:
CONSTRUCTION
AGENCY
04-SAMSS-051 Ball Valves, API SPEC 6D
DATE:
04-SAMSS-053 Steel Lubricated Plug Valves - Flanged and Welding End
OPERATIONS
06-SAMSS-001 Selection and Qualification of Elastomeric Sealing Materials
DATE:
and Manufacturers
CONTROL NUMBER
VERIFICATION
Types of valves and trim shall be in accordance with the individual Line classes,
EDSD
All SW gate, globe and check valves shall conform to API 602 as applicable
BY:
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
All ball and globe valves shall be reduced bore, unless required by process
(DCC) NO. _____________________
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
Ball valves NPS 6” and larger in Classes 150 and 300, and all sizes in Class 600
ENGG CERT
RSJ
RSJ
Gate and check valve bore dimension shall be supplied in accordance with the
specified standard.
Check valve type shall be Dual Plate check valve for NPS 2 and above. In case of
dissimilar check valve scenario (as per P&ID), Swing type check valve shall be
used.
Dual Plate check valve shall be considered double flanged for below sizes and
DESCRIPTION
wafer lugged type for other sizes. This shall be further verified with vendors based
on vendors manufacturing range and shall be revised accordingly.
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
Rating Size
ISSUED FOR DESIGN
01900-0004
BI-10-
29SEPT16 BI-10-
DATE
Fire safe design shall be applicable for soft seated Ball, Butterfly and Plug Valves
and shall NOT be applicable for Metal Seated Ball, Butterfly, Plug Valves (with
graphite seals) and Gate, Globe, Check Valves (with graphite packing).
NO.
REV
00
B
Face to Face – end to end dimensions shall be in accordance with ASME B16.10
EDSD
Steel –end flanges on valve NPS 2 to NPS 24 shall be in accordance with ASME
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
B16.5. Steel –end flanges on valve NPS 26 and larger are in accordance with
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
Gear operated valves shall be used f o r sizes (including and above) & rating as
per below table in order to provide the recommended operational effort. Bevel
ENGG CERT
RSJ
RSJ
sizes may be equipped with gear operators, valve vendors shall provide gear
operator for the valves.
VALVE TYPE
01900-0004
Valve trim designators for gate, globe and check valves shall be in accordance
BI-10-
29SEPT16 BI-10-
The use of clamp-on type chain wheels for valves larger than 2” NPS shall
require COMPANY written approval.
NO.
REV
00
B
DISCIPLINE
ENGINEER All wrench operated ball valves in insulated lines shall have NPS 6” extended
NLP / SSK
spindle (measured from the valve bonnet) to ensure that the wrench clears the
29/09/2016
DATE: valve insulation. The spindle shall have an outer stationary tube welded to the
PROJECT
LEAD
ENGINEER valve bonnet and having a weather seal at the wrench end. The stationary tube
ENGINEER
TNPRAG / RD
/ RAG enables the insulation to be properly sealed around it.
29/09/2016
DATE:
CERTIFIED
PB / RSJ / KR
Stainless Steel Valves shall be dual grade for socket weld and butt-weld valves
29/09/2016
and dual grade or standard grade for flanged valves. Low carbon grades of
DATE: austenitic stainless steels are acceptable substitutes for the corresponding
CONSTRUCTION
AGENCY regular carbon grades, but not vice versa.
Above 356ºF (180ºC) the use of soft seat is dependent upon the material used
EDSD
design.
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
Butterfly valves shall be double flanged style or lug-wafer type design with tapped
00
bolt holes.
(DCC) NO. _____________________
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
Isolation Valves and Emergency Isolation Valves may be gate, ball or plug valves
ENGG CERT
RSJ
RSJ
that can be locked open or closed. Flanged butterfly valves, high performance
offset construction type, may be used for Isolation and Emergency Isolation
RAG
RAG
services when required by Process and indicated on the P&IDs. Ball valves used
for Emergency shutdown service shall be trunnion mounted type. Soft seated
isolation valves shall have “zero” leakage in accordance with the valve design
specification. Double isolation valves shall be provided for all drains in
Hydrocarbon Service however, with respect to atmospheric vents and drains, a
single valve with a screwed plug may be considered as “double isolation”.
DESCRIPTION
In reciprocating pump and compressor suction and discharge lines and similar
services, swing check type valves are not permitted. Spring-assisted non-slam
piston check (also referred to as nozzle check) valves shall be used in these
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
situations and also at discharge lines in parallel pump and compressor systems.
ISSUED FOR DESIGN
01900-0004
BI-10-
29SEPT16 BI-10-
All MOVs and their bypass valves on pumps and compressors and at plant
isolation locations
NO.
REV
00
B
DISCIPLINE
ENGINEER
NLP / SSK All ZVs and their bypass valves
29/09/2016
DATE:
PROJECT
LEAD
ENGINEER
All pressure control valves (PCVs) that are normally closed
ENGINEER
TNPRAG / RD
/ RAG
DATE:
29/09/2016 All block valves
CERTIFIED
PB / RSJ / KR
All isolation valves for control valves and their bypass valves that are in
29/09/2016
DATE: process service (oil, gas and water; not utility service)
CONSTRUCTION
AGENCY
All valves designated as “TSO” (tight shut-off) on the P&IDS.
DATE:
OPERATIONS A low pressure pneumatic seat test at 35 kPa (5 psig) shall be substituted for the
high pressure hydrostatic seat test for flare system valves.
DATE:
Buttweld and socketweld end valves in nominal pipe size (NPS) 2 inches and
CONTROL NUMBER
VERIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
Start-Up Requirements and Valve Repairs for all field tested valves shall follow
OF THIS DRAWING IS COVERED, FOR ALL
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
01900-0004
Graphite
BI-10-
29SEPT16 BI-10-
Not
00
B
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
ENGG CERT
RSJ
RSJ
All dissimilar metal flanged joints shall be provided with insulating kits as per
SAES-L-109 “Selection of Flanges, Stud Bolts and Gaskets”
Equipment.
ISSUED FOR DESIGN
01900-0004
BI-10-
29SEPT16 BI-10-
3.26 Materials
DATE
00
B
Requirement for CS and Low Alloy Steel (For piping, fittings, flanges & valves)
DATE:
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
Internal Fusion Bonded Epoxy lining wherever required as per applicable pipe class
shall be carried out as per Project Specification for Internal Lining (D44-H-RE-
ENGG CERT
RSJ
RSJ
380908).
RAG
RAG
For Piping Commodity Code details, refer “Piping Commodity Code Description”,
Doc. No. D44-A-RE-585277.
The base piping line class designator system consists of five alpha-numeric fields
containing one or two characters each. Each field describes various features of
the piping line class as shown in Table 4
01900-0004
Field Location
BI-10-
29SEPT16 BI-10-
00
B
DATE:
29/09/2016 Explanation 300# Carbon 3mm General Sour
CERTIFIED Rating Steel Corrosion Hydrocarbon Service
PB / RSJ / KR
Allowance
29/09/2016
DATE:
CONSTRUCTION
AGENCY
The Piping Line Classes and service designations are based on Company
corporate requirements modified to add project specific requirements. These
DATE:
modifications are described below:
OPERATIONS
Addition of the last two digits in the Pipe Class designation
DATE:
includes project specific requirements
CONTROL NUMBER
VERIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
15 1500
ISSUED FOR DESIGN
25 2500
01900-0004
BI-10-
29SEPT16 BI-10-
NO. DATE
REV
00
B
DISCIPLINE
ENGINEER
NLP / SSK
29/09/2016
DATE:
PROJECT
LEAD
ENGINEER
ENGINEER
TNPRAG / RD
/ RAG
29/09/2016
DATE:
CERTIFIED
PB / RSJ / KR
29/09/2016
DATE:
CONSTRUCTION
AGENCY
DATE:
OPERATIONS
DATE:
CONTROL NUMBER
VERIFICATION
EDSD
DATE:
BY:
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
2nd - Material
ENGG CERT
RSJ
RSJ
Polypropylene-lined Carbon
BC Copper Tubing LP Steel
RAG
RAG
01900-0004
29SEPT16 BI-10-
00
B
protection requirements
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
4th - Service
RAG
RAG
designator)
P Process
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
01900-0004
29SEPT16 BI-10-
00
05 Buried
B
DISCIPLINE
ENGINEER HIC Resistance, Sour Service, NACE MR-0175/ISO 15156 or NACE MR-0103
NLP / SSK 06
29/09/2016
as applicable
DATE:
PROJECT
LEAD
ENGINEER
HIC Resistance, Sour Service, NACE MR-0175/ISO 15156 or NACE MR-0103 as
ENGINEER
TNPRAG / RD
/ RAG
07 applicable + Fusion Bonded Epoxy Lined in accordance with 09-SAMSS-091
29/09/2016
(Internal Coated)
DATE:
CERTIFIED
PB / RSJ / KR 08 Design Code per ASME B31.8 (optional)
29/09/2016
DATE:
09 HIC Resistance, Sour Service, NACE MR-0175/ISO 15156 or NACE MR-0103
CONSTRUCTION
AGENCY as applicable, LETHAL Service
10 Sour Service, NACE MR-0175/ISO 15156 or NACE MR-0103 as applicable, LETHAL
DATE: Service
OPERATIONS
11 Sour Service, NACE MR-0175/ISO 15156 or NACE MR-0103 as applicable, AMINE
DATE:
Service
CONTROL NUMBER
12
as applicable, AMINE Service
EDSD
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
18 Additional pipeline classes (ASME B31.4) with HIC Resistance, Sour Service,
(DCC) NO. _____________________
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
19 Additional pipeline classes (ASME B31.8) with HIC Resistance, Sour Service,
NACE MR-0175/ISO 15156 or NACE MR-0103 as applicable
ENGG CERT
RSJ
RSJ
1 13 Cr 13 Cr
2 SS 304 SS 304
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
3 SS 310 SS 310
ISSUED FOR DESIGN
4 13 Cr Hardened 13 Cr Hardened
5 Co-Cr Hardfacing Co-Cr Hardfacing
5A Ni-Cr Hardfacing Ni-Cr Hardfacing
6 13 Cr Cu-Ni
JO/EWO
01900-0004
7 13 Cr Hardened 13 Cr
BI-10-
29SEPT16 BI-10-
8 Co-Cr Hardfacing 13 Cr
DATE
8A Ni-Cr Hardfacing 13 Cr
9 Monel Monel
NO.
REV
00
B
DATE:
29/09/2016 13 Alloy 20 Alloy 20
CERTIFIED Ni-Cr or Co-Cr
PB / RSJ / KR 14 Alloy 20
Hardfacing
29/09/2016
DATE:
CONSTRUCTION
AGENCY Notes:
DATE:
OPERATIONS
When a combination trim is shown (Trim No.'s 6, 7, 8, 8A, 11, 12, or 14), the
seating surface materials of the seat and closure member may be
interchanged.
DATE:
CONTROL NUMBER
VERIFICATION
DATE:
BY:
APPROVAL/CERTIFICATION REQUIREMENTS,
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
29SEPT16 BI-10-
00
B
DATE:
29/09/2016 SAEP-35 Valves Handling, Hauling, Receipt Tests and Storage
PROJECT
LEAD
ENGINEER
ENGINEER
RAG / RD
SAEP-302 Instructions for Obtaining a Waiver of a Mandatory Saudi Aramco
TNP / RAG
29/09/2016
Engineering Requirement.
DATE:
CERTIFIED
PB / RSJ / KR SAEP-311 Installation of Hot Tap and Stopple Connections
29/09/2016
DATE:
CONSTRUCTION SAEP-347 Supplying Material from Stockiest
AGENCY
Equipment
VERIFICATION
EDSD
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
SAES-H-002 Internal and External Coatings for Steel Pipelines and Piping
01900-0004
SAES-L-101 Regulated Vendors List for Pipes, Fittings, Flanges and Tubes
BI-10-
29SEPT16 BI-10-
00
B
DISCIPLINE
ENGINEER SAES-L-108 Selection of Valves
NLP / SSK
29/09/2016
DATE:
PROJECT
SAES-L-109 Selection of Flanges, Stud Bolts and Gaskets
LEAD
ENGINEER
ENGINEER
TNPRAG / RD
/ RAG SAES-L-110 Limitations on Pipe Joints and Components
29/09/2016
DATE:
CERTIFIED
PB / RSJ / KR
SAES-L-120 Piping Flexibility Analysis
29/09/2016
DATE:
SAES-L-125 Safety Instruction Sheet for Piping and Pipelines
CONSTRUCTION
AGENCY
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
01900-0004
29SEPT16 BI-10-
DATE
00
B
DISCIPLINE
ENGINEER
NLP / SSK
SAES-S-040 Saudi Aramco Water Systems
29/09/2016
DATE:
PROJECT
SAES-S-050 Sprinkler and Standpipe Systems in Buildings
LEAD
ENGINEER
ENGINEER
RAG / RD
TNP / RAG SAES-S-060 Saudi Aramco Plumbing Code
29/09/2016
DATE:
CERTIFIED
PB / RSJ / KR SAES-S-070 Installation of Utility Piping Systems
29/09/2016
DATE:
CONSTRUCTION
SAES-W-011 Welding Requirements for On-Plot Piping
AGENCY
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
01-SAMSS-029 RTR (Fiberglass) Sewer Pipe and Fittings for Gravity Flow
pipe Mills
ISSUED FOR DESIGN
01900-0004
29SEPT16 BI-10-
00
B
DISCIPLINE
ENGINEER 01-SAMSS-049 Reinforced Thermoset Resin (RTR) Pipe, Fittings and
NLP / SSK
29/09/2016
Adhesive Packing, Handling, Transportation and Storage
DATE:
PROJECT
LEAD
ENGINEER
ENGINEER
RAG / RD
01-SAMSS-333 High Frequency Welded Line Pipe
TNP / RAG
29/09/2016
DATE:
CERTIFIED 02-SAMSS-005 Butt Welding Pipe Fittings
PB / RSJ / KR
DATE:
29/09/2016 02-SAMSS-011 Forged Steel and Alloy Flanges
CONSTRUCTION
AGENCY
02-SAMSS-012 Weld Overlayed Fittings, Flanges and Spool Pieces
DATE:
OPERATIONS
04-SAMSS-001 Gate Valves
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
01900-0004
BI-10-
29SEPT16 BI-10-
00
B
DISCIPLINE
ENGINEER 09-SAMSS-090 Shop-Applied Extruded P.E. External Coating System for Line
NLP / SSK
29/09/2016
Pipe
DATE:
PROJECT
LEAD
ENGINEER
ENGINEER
09-SAMSS-091 Qualification Requirements for Shop-Applied Internal FBE
RAG / RD
TNP / RAG Coatings
29/09/2016
DATE:
CERTIFIED
PB / RSJ / KR 09-SAMSS-107 Qualification Requirements and Application of Composite
29/09/2016
Fluoropolymer/Ceramic Coatings to Fasteners
DATE:
CONSTRUCTION
AGENCY Saudi Aramco Standard Drawings
(SSD/26.AES-0-126)
EDSD
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
AB-036521-001 Bridge Weld and Typical Brace Seal Welded and Socket
Welded Valves on Process Lines
ENGG CERT
RSJ
RSJ
AC-036484-001 Weld Neck Flanges and Blind Flanges, Large Size, Class 300
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
Ring Joint
ISSUED FOR DESIGN
AC-036486-001 Lap Joint Flanges and Stub Ends, Large Size, Class 300 Ring
Joint
AC-036688-001 Conical Pump Suction Screen Class 150 and 300 Flanges –
Pipe Sizes 16” and Larger
JO/EWO
01900-0004
BI-10-
29SEPT16 BI-10-
AD-036080-001 Conical Pump Suction Screen for Raised Face Flanges Pipe
DATE
00
B
DISCIPLINE
AD-036439-001 Spectacle Plates, Blinds and Spacers for 54” and 60” Flanges
ENGINEER Class 150 and 300
NLP / SSK
29/09/2016
DATE: AD-036495-001 Conical Pump Suction Screen for Raised Face Flanges Pie
PROJECT
LEAD
ENGINEER
ENGINEER
Sizes 6, 8, 10, 12 and 14 Inches
TNPRAG / RD
/ RAG
DATE:
29/09/2016
AD-036630-001 Installation of Jack Screws for Flanged Joints
CERTIFIED
PB / RSJ / KR
29/09/2016
AD-036631-001 Spectacle Plates, Blinds and Spacers for Class 125 Cast Iron
DATE:
Flanges
CONSTRUCTION
AGENCY
AD-036633-001 Spectacle Plates, Blinds and Spacers for Class 150 Raised
DATE: Face Flanges
OPERATIONS
AD-036634-001 Weld Neck and Blind Flanges, Large Size, Class 150 R.F.
DATE:
AD-036636-001 Spectacle Plates, Blinds and Spacers for Class 600 Raised
CONTROL NUMBER
VERIFICATION
Face Flanges
EDSD
AD-036673-001 W.N. Flanges and Blind Flanges, Large Size, Class 600 R.F.
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
AD-036698-001 W.N. Flanges and Blind Flanges, Large Size, Class 400 R.F.
(DCC) NO. _____________________
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
AD-036731-001 Spectacle Plates, Blinds and Spacers, for Class 300 Raised
Face Flanges
ENGG CERT
RSJ
RSJ
AD-036734-001 Spectacle Plates, Blinds and Spacers, for Class 600 Octagonal
RAG
RAG
AD-036735-001 Spectacle Plates, Blinds and Spacers for Class 900 Octagonal
Ring Joint Flanges
AD-036991-001 W.N. Flanges and Blind Flanges, Large Size, Class 300 R.F.
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
01900-0004
29SEPT16 BI-10-
00
B
DISCIPLINE
ENGINEER SAIC-L-2042 Field Hydrostatic Testing of Isolation Valves
NLP / SSK
29/09/2016
DATE:
PROJECT
5.2 Industry Codes, Standards and Specifications
LEAD
ENGINEER
ENGINEER
TNPRAG / RD
/ RAG
DATE:
29/09/2016 American Petroleum Institute (API)
CERTIFIED
PB / RSJ / KR
API SPEC 5L Specification for Line Pipe
29/09/2016
DATE:
CONSTRUCTION
AGENCY
API SPEC 6A Specification for Wellhead and Christmas Tree Equipment
API STD 599 Metal Plug Valves – Flanged, Threaded, and Welding Ends
BY:
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
API STD 600 Steel Gate Valves – Flanged and Butt-welding Ends, Bolted
OF THIS DRAWING IS COVERED, FOR ALL
Bonnets
(DCC) NO. _____________________
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
API STD 602 Steel Gate, Globe and Check Valves for sizes NPS 4 (100) and
smaller for the Petroleum and Natural Gas Industries
ENGG CERT
RSJ
RSJ
API STD 603 Corrosion – resistant, Bolted Bonnet Gate Valves – Flanged
RAG
RAG
API STD 607 Fire Test for Quarter-turn Valves and Valves Equipped with
Non-metallic seats
ASME B16.1 Gray Iron Pipe Flanges and Flanged Fittings, Classes 25, 125
and 250
JO/EWO
01900-0004
ASME B16.3 Malleable Iron Threaded Fittings Classes 150 and 300
BI-10-
29SEPT16 BI-10-
ASME B16.5 Pipe Flanges and Flanged Fittings NPS ½ Through NPS 24
DATE
metric/inch Standard
NO.
REV
00
B
DISCIPLINE
ASME B16.9 Factory-Made Wrought Butt welding Fittings
ENGINEER
NLP / SSK
ASME B16.10 Face-to-Face and End-to-End Dimensions of Valves
29/09/2016
DATE:
PROJECT
LEAD
ENGINEER
ENGINEER
TNPRAG / RD
/ RAG ASME B16.11 Forged Fittings, Socket-Welding and Threaded
29/09/2016
DATE:
CERTIFIED
PB / RSJ / KR
ASME B16.20 Metallic Gaskets for Pipe Flanges Ring Joint, Spiral Wound and
29/09/2016
Jacketed
DATE:
CONSTRUCTION
AGENCY ASME B16.21 Non-metallic Flat Gaskets for Pipe Flanges
DATE: ASME B16.22 Wrought Copper and Copper Alloy Solder-Joint Pressure
OPERATIONS
Fittings
DATE: ASME B16.24 Cast Copper Alloy Pipe Flanges and Flanged Fittings Classes
150, 300, 600, 900, 1500, and 2500
CONTROL NUMBER
VERIFICATION
EDSD
ASME B16.28 Wrought Steel Butt welding Short Radius Elbows and Returns
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
ASME B16.42 Ductile Iron Pipe Flanges and Flanged Fittings Classes 150
ENGG CERT
RSJ
RSJ
and 300
RAG
RAG
01900-0004
29SEPT16 BI-10-
ASME B18.2.1 Square, Hex, Heavy Hex, and Askew Head Bolts and Hex,
NO.
REV
00
B
Heavy Hex, Hex Flange, Lobed Head, and Lag Screws (Inch
DISCIPLINE
ENGINEER Series)
NLP / SSK
29/09/2016
DATE:
ASME B18.2.2 Nuts for General Applications: Machine Screw Nuts, Hex,
PROJECT
LEAD
ENGINEER
ENGINEER
Square, Hex Flange, and Coupling Nuts (Inch Series)
TNPRAG / RD
/ RAG
29/09/2016
DATE: American Society for Testing and Materials (ASTM)
CERTIFIED
PB / RSJ / KR
29/09/2016
DATE:
CONSTRUCTION
ASTM A36 Standard Specification for Carbon Structural Steel
AGENCY
ASTM A53 Standard Specification for Pipe, Steel, Black and Hot-Dipped,
DATE:
OPERATIONS
Zinc-Coated, Welded and Seamless
DATE:
ASTM A105 Standard Specification for Carbon Steel Forgings for Piping
CONTROL NUMBER
VERIFICATION
Applications
EDSD
ASTM A106 Standard Specification for Seamless Carbon Steel Pipe for High-
DATE:
Temperature Service
BY:
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
ASTM A182 Standard Specification for Forged or Rolled Alloy and Stainless
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
Steel Pipe Flanges, Forged Fittings, and Valves and Parts for
High-Temperature Service
ENGG CERT
RSJ
RSJ
ASTM A193 Standard Specification for Alloy-Steel and Stainless Steel Bolting
RAG
RAG
ASTM A194 Standard Specification for Carbon and Alloy Steel Nuts for Bolts
for High Pressure or High Temperature Service, or Both
ASTM A216 Standard Specification for Steel Castings, Carbon, Suitable for
DESCRIPTION
01900-0004
29SEPT16 BI-10-
ASTM A266 Standard Specification for Carbon Steel Forgings for Pressure
NO.
REV
00
B
DISCIPLINE
Vessel Components
ENGINEER
NLP / SSK
29/09/2016
ASTM A269 Standard Specification for Seamless and Welded Austenitic
DATE:
PROJECT
Stainless Steel Tubing for General Service
LEAD
ENGINEER
ENGINEER
RAG / RD
TNP / RAG
29/09/2016
ASTM A307 Standard Specification for Carbon Steel Bolts, Studs, and
DATE:
CERTIFIED
Threaded Rod 60,000 PSI Tensile Strength
PB / RSJ / KR
DATE:
29/09/2016 ASTM A312 Standard Specification for Seamless, Welded, and Heavily Cold
CONSTRUCTION Worked Austenitic Stainless Steel Pipes
AGENCY
DATE:
ASTM A320 Standard Specification for Alloy-Steel and Stainless Steel Bolting
OPERATIONS for Low-Temperature Service
DATE:
ASTM A333 Standard Specification for Seamless and Welded Steel Pipe for
Low-Temperature Service and Other Applications with Required
CONTROL NUMBER
VERIFICATION
Notch Toughness
EDSD
ASTM A335 Standard Specification for Seamless Ferritic Alloy-Steel Pipe for
DATE:
High-Temperature
BY:
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
ASTM A350 Standard Specification for Carbon and Low-Alloy Steel Forgings,
OF THIS DRAWING IS COVERED, FOR ALL
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
01900-0004
ASTM A494 Standard Specification for Castings, Nickel and Nickel Alloy
BI-10-
29SEPT16 BI-10-
00
B
DISCIPLINE
ENGINEER
NLP / SSK
ASTM A691 Standard Specification for Carbon and Alloy Steel Pipe, Electric-
29/09/2016
Fusion-Welded for High-Pressure Service at High Temperatures
DATE:
PROJECT
LEAD
ENGINEER
ENGINEER ASTM A694 Standard Specification for Carbon and Alloy Steel Forgings for
RAG / RD
TNP / RAG
Pipe Flanges, Fittings, Valves, and Parts for High-Pressure
29/09/2016
DATE:
CERTIFIED
Transmission Service
PB / RSJ / KR
DATE:
29/09/2016 ASTM A707 Standard Specification for Forged Carbon and Alloy Steel
CONSTRUCTION Flanges for Low-Temperature Service
AGENCY
DATE:
ASTM A789 Standard Specification for Seamless and Welded Ferritic /
OPERATIONS Austenitic Stainless Steel Tubing for General Service
DATE:
ASTM A790 Standard Specification for Seamless and Welded Ferritic /
Austenitic Stainless Steel Pipe
CONTROL NUMBER
VERIFICATION
EDSD
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
ASTM A860 Standard Specification for Wrought High Strength Ferritic Steel
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
Butt-Welding Fittings
ENGG CERT
RSJ
RSJ
General Application
Castings
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
01900-0004
BI-10-
29SEPT16 BI-10-
00
B
DISCIPLINE
Pipe and Tube
ENGINEER
NLP / SSK
29/09/2016 ASTM B409 Standard Specification for Nickel-Iron-Chromium Alloy Plate,
DATE:
PROJECT Sheet, and Strip
LEAD
ENGINEER
ENGINEER
TNPRAG / RD
/ RAG
29/09/2016
ASTM B462 Standard Specification for Forged or Rolled UNS N06030, UNS
DATE:
CERTIFIED N06022, UNS N06035, UNS N06200, UNS N06059, UNS
PB / RSJ / KR N10362, UNS N06686, UNS N08020, UNS N08024, UNS
DATE:
29/09/2016 N08026, UNS N08367, UNS N10276, UNS N10665, UNS
CONSTRUCTION N10675, UNS N10629, UNS N08031, UNS N06045, UNS
AGENCY
N06025, UNS R20033 Alloy Pipe Flanges, Forged Fittings, and
DATE:
Valves and Parts for Corrosive High-Temperature Service
OPERATIONS
ASTM B463 Standard Specification for UNS N08020, Alloy Plate, Sheet, and
DATE:
Strip
CONTROL NUMBER
VERIFICATION
ASTM B464 Standard Specification for Welded UNS N08020 Alloy Pipe
EDSD
Tube
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
ASTM B474 Standard Specification for Electric Fusion Welded and Nickel
Alloy Pipe
ENGG CERT
RSJ
RSJ
ASTM D1784 Standard Specification for Rigid Poly (Vinyl Chloride) (PVC)
Compounds and Chlorinated Poly (Vinyl Chloride) (CPVC)
DESCRIPTION
Compounds
04AUG16 01900-0004 RE-ISSUED FOR REVIEW
ASTM D1785 Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic
ISSUED FOR DESIGN
ASTM D2467 Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic
Pipe Fittings, Schedule 80
ASTM D2564 Standard Specification for Solvent Cements for Poly (Vinyl
JO/EWO
01900-0004
29SEPT16 BI-10-
ASTM D2665 Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic
DATE
00
B
DISCIPLINE
ASTM D3034 Standard Specification for Type PSM Poly (Vinyl Chloride)
ENGINEER
NLP / SSK
(PVC) Sewer Pipe and Fittings
29/09/2016
DATE:
PROJECT
ASTM D3311 Standard Specification for Drain, Waste and Vent (DWV) Plastic
LEAD
ENGINEER
ENGINEER Fittings Patterns
TNPRAG / RD
/ RAG
29/09/2016
DATE:
CERTIFIED
ASTM F437 Standard Specification for Threaded Chlorinated Poly (Vinyl
PB / RSJ / KR Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
29/09/2016
DATE:
CONSTRUCTION ASTM F439 Standard Specification for Chlorinated Poly (Vinyl Chloride)
AGENCY
(CPVC) Plastic Pipe Fittings Schedule 80
DATE:
OPERATIONS ASTM F441 Standard Specification for Chlorinated Poly (Vinyl Chloride)
(CPVC) Plastic Pipe, Schedules 40 and 80
DATE:
ASTM F493 Standard Specification for Solvent Cements for Chlorinated Poly
CONTROL NUMBER
VERIFICATION
British Standards
DATE:
BY:
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
BS 1873 Specification for Steel Globe and Globe Stop and Check Valves
(DCC) NO. _____________________
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
BS 5154 Copper Alloy Globe, Globe Stop and Check, Check and Gate
Valves
RAG
RAG
BS EN 10312 Welded stainless steel tubes for the conveyance of water and
ISSUED FOR DESIGN
01900-0004
29SEPT16 BI-10-
DATE
BS EN ISO 10434 Bolted bonnet steel gate valves for the petroleum,
petrochemical and allied industries
NO.
REV
00
B
DATE:
29/09/2016 BS EN ISO 15848-1 Industrial valves —Measurement, test and qualification procedures
CONSTRUCTION or fugitive emissions — Part 1: Classification system and
AGENCY
qualification procedures for type testing of valves
DATE:
BS EN ISO 15848-2 Industrial valves —Measurement, test and qualification procedures
OPERATIONS
or fugitive emissions — Part 2: Production acceptance test of
valves
DATE:
EEMUA PUB NO 144 90/10 Copper Nickel Piping for Offshore Applications –
Specification: Seamless and Welded Tubes – Seamless
DATE:
BY:
and Welded
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
EEMUA PUB NO 145 90/10 Copper Nickel Piping for Offshore Applications –
(DCC) NO. _____________________
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
EEMUA PUB NO 146 90/10 Copper Nickel Piping for Offshore Applications –
ENGG CERT
RSJ
RSJ
Specification: Fittings
RAG
RAG
01900-0004
29SEPT16 BI-10-
DATE
00
B
DISCIPLINE
ENGINEER
NLP / SSK
MSS SP-6 Standard Finishes for Contact Faces of Pipe Flanges and
29/09/2016 Connecting-End Flanges of Valves and Fittings
DATE:
PROJECT
LEAD
ENGINEER
ENGINEER
RAG / RD
MSS SP-25 Standard Marking System for Valves, Fittings, Flanges and
TNP / RAG
29/09/2016
Unions
DATE:
CERTIFIED
PB / RSJ / KR MSS SP-43 Wrought and Fabricated Butt-Welding Fittings for
DATE:
29/09/2016 Low Pressure, Corrosion Resistant Applications
CONSTRUCTION
AGENCY
MSS SP-75 Specification for High-Test, Wrought, Butt-Welding Fittings MSS
DATE: SP-80 Bronze Gate, Globe, Angle, and Check Valves
OPERATIONS MSS SP-83 Class 3000 Steel Pipe Unions Socket-Welding and Threaded
MSS SP-95 Swage (d) Nipples and Bull Plugs
DATE: MSS SP-97 Integrally Reinforced Forged Branch Outlet Fittings - Socket
Welding, Threaded and Butt-Welding Ends
CONTROL NUMBER
VERIFICATION
EDSD
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT OPRNS
SAUDI ARABIAN OIL COMPANY
RSJ
RSJ
01900-0004
BI-10-
29SEPT16 BI-10-
Engineering Standard
NO.
REV
00
B
DISCIPLINE
ENGINEER
NLP / SSK
29/09/2016
DATE:
PROJECT
LEAD
ENGINEER
ENGINEER
TNPRAG / RD
/ RAG
29/09/2016
DATE:
CERTIFIED
PB / RSJ / KR
29/09/2016
DATE:
CONSTRUCTION
AGENCY
DATE:
OPERATIONS
DATE:
CONTROL NUMBER
VERIFICATION
EDSD
DATE:
BY:
REVISIONCERTIFICATION
APPROVAL/CERTIFICATION REQUIREMENTS,
THIS INDICATES THAT REV. NO.__________
CERTIFICATE
PROJECT SPECIFICATION DWG.TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
REVISION
DATE:
DATE:
DATE:
DATE:
DATE:
THIS INDICATES THAT REV. NO.__________ BI-10-
TNP
LEAD
OF THIS DRAWING IS COVERED, FOR ALL B 04AUG16 01900-0004 RE-ISSUED FOR REVIEW RAG RSJ
RAG
CONTROL NUMBER
APPROVAL/CERTIFICATION REQUIREMENTS, 29SEPT16 BI-10-
/ RAG
RAG RSJ
ENGINEER
00 01900-0004 ISSUED FOR DESIGN
AGENCY
NLP / SSK
/ RD
BY:
PROJECT
BY DRAWING COMPLETION CERTIFICATE
ENGINEER
ENGINEER
PB / RSJ / KR
DISCIPLINE
CERTIFIED
29/09/2016
29/09/2016
29/09/2016
OPERATIONS
CONSTRUCTION
(DCC) NO. _____________________ DATE:
``
SAUDI ARABIA
D44
JO / EWO:
A
DWG.TYPE PLANT NO. INDEX
SAUDI ARABIAN OIL COMPANY
BI-10-01900-0004
DRAWING NO.
RE- 585265
64
56
OF
SHT. NO.
D44-A-RE-585265 Rev00.doc
00
REV. NO.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
APPENDIX 1 PROJECT TITLE : FADHILI GAS PLANT
DOCUMENT NO. : D44-A-RE-585265 REV 00
PIPE CLASS SERVICE INDEX CLIENT: SAUDI ARAMCO
NEW PIPE CLASS ASME DESIGN
FLUID NACE FLANGE SIZE
DESIGNATION AS CLASS FLUID LETHAL PWHT CA VALVE VALVE B16.5 TEMP DESIGN PRESS RANGE VALVE NDE EXTENT
REV. SERVICE DESCRIPTION Code Fluid CATEGORY TOXIC HIC MR0175- PIPE MATERIAL FITTING MATERIAL FLANGE MATL. VALVE MATL. CONSTRUCT FACE EXTERNAL PRESSURE BOLTING GASKET (S) RANGE NOTE
PER SAES-L-105 RATING SYMBOL (NOTE 68) (Note 20) [mm] TRIM PACKING MAT,L RANGE [PSIG] TYPE (% PERCENTAGE)
(NOTE 86) ISO 15156 TYPE [Inch]
(NOTE 22) GROUP [DEG F]
RT MT PT VT
SHOP FIELD
WELD WELD
LOW TEMP HYDROCARBON PROCESS -
ASTM A350 LF2 CL 1 FEXIBLE ASTM A350 LF2 CL 1 A320 Gr.L7 316L SS SPW / BA, CH, GA,
00 1CA1P01 150 NON CORROSIVE SPO B31.3 LIQUID N NO NO NO NO NO ASTM A333 GR.6 - SMLS 1.6 TRIM 12 1.3 ASTM A350 LF2 CL 1 SW, BW, WN RF -46 to 185 ASME B16.5 0.5”-24” 10% 100% 100% NONE 100% 1, 17, 21
ASTM A420 WPL6-S GRAPHITE ASTM A352 LCB A194 Gr.4-S3 GRAPHITE GL
SLOP OIL (INCLUDING OILY SLUDGE)
LOW TEMP HYDROCARBON PROCESS -
WET SOUR H2S
LOW PRESSURE FUEL GAS FGL NO ASME B16.5 0.5”-24”
GAS ASTM A350 LF2 CL 1 FV- upto 4”
HIGH PRESSURE FLARE HPF YES ASTM A333 GR.6 - SMLS FEXIBLE ASTM A350 LF2 CL 1 A320 Gr.L7M 316L SS SPW / BA, ,CH, GA,
00 1CA2P06 150 B31.3 VAPOUR N NO YES YES YES ASTM A420 WPL6-S 3.2 TRIM 12 1.3 ASTM A350 LF2 CL 1 BW, WN RF ˗50 to 460 HV- 6" to 16” 10% 100% 100% NONE 100% 1, 17, 21
ASTM A671 CC65 - CL22 (S2) - EFW GRAPHITE ASTM A352 LCB A194 Gr.7M-S3 GRAPHITE GL, BU
HIGH PRESSURE FLARE HPF2 LIQUID YES ASTM A420 WPL6-W 160 PSIG @ 350 DEG F HV-18" to 56” (Alt)
UTILITY WATER UW NO 240 PSIG @ 180 DEG F 26" - 76"
60 PSIG LLP STEAM 60S NO 102 PSIG @ 460 DEG F
LOW TEMP HYDROCARBON PROCESS -
WET SOUR H2S - CATEGORY M SERVICE ASME B16.5 0.5"-24”
LOW PRESSURE FLARE LPF ASTM A350 LF2 CL 1
ASTM A333 GR.6 - SMLS FEXIBLE ASTM A350 LF2 CL 1 HV- upto 30” A320 Gr.L7M 316L SS SPW / BA, BU, CH,
00 1CA2P09 150 HIGH PRESSURE FLARE HPF B31.3 VAPOUR M YES YES YES YES YES ASTM A420 WPL6-S 3.2 TRIM 12 1.3 ASTM A350 LF2 CL 1 BW, WN RF -50 to 460 240 PSIG @ 180 DEG F 100% 100% 100% NONE 100% 1, 17, 21
ASTM A671 CC65 - CL22 (S2) - EFW GRAPHITE ASTM A352 LCB HV-32" to 76” (Alt) A194 Gr.7M-S3 GRAPHITE GA, GL
ASTM A420 WPL6-W
LOW PRESSURE FLARE LPF1 160 PSIG @ 350 DEG F
26” – 76”
HIGH PRESSURE FLARE HPF1 102 PSIG @ 460 DEG F
LOW PRESSURE FLARE LPF2
UTILITY SERVICE
ASTM A105N HOT DIP
INSTRUMENT AIR IA ASTM A106 GR B HOT DIP GALV - FEXIBLE ASTM A105N HOT ASTM A105N A193 GR B7 BA, CH, GA, 1, 17, 57,
00 1CG0U01 150 B31.3 GAS N NO NO NO NO NO GALVANISED 0 TRIM 8 1.1 THRD, BW, WN FF 32 to 185 ASME B16.5 SYNTHETIC FIBRE 0.5"-6" - - 100% NONE 100%
PROCESS AIR PA SMLS GRAPHITE DIP GALVANISED ASTM A216 WCB A194 GR 2H GL 37, 31
ASTM A234 WPB-S GALVANISED
UTILITY AIR UA
CAUSTIC SERVICE
ASTM A105N FLEXIBLE ASTM A105N A193 GR B7 316L SS SPW /
00 1CH2C01 150 B31.3 LIQUID N NO NO NO NO YES ASTM A106 GR B 3.2 TRIM 12 1.1 ASTM A105N SW, BW, WN RF 32 to 180 ASME B16.5 0.5"-6" CH, GA, GL 10% 10% 100% NONE 100% 1, 17
ASTM A234 WPB-S GRAPHITE ASTM A216 WCB A194 GR 2H GRAPHITE
CHEMICAL (CAUSTIC) CS
57 of 64
APPENDIX 1 PROJECT TITLE : FADHILI GAS PLANT
DOCUMENT NO. : D44-A-RE-585265 REV 00
PIPE CLASS SERVICE INDEX CLIENT: SAUDI ARAMCO
NEW PIPE CLASS ASME DESIGN
FLUID NACE FLANGE SIZE
DESIGNATION AS CLASS FLUID LETHAL PWHT CA VALVE VALVE B16.5 TEMP DESIGN PRESS RANGE VALVE NDE EXTENT
REV. SERVICE DESCRIPTION Code Fluid CATEGORY TOXIC HIC MR0175- PIPE MATERIAL FITTING MATERIAL FLANGE MATL. VALVE MATL. CONSTRUCT FACE EXTERNAL PRESSURE BOLTING GASKET (S) RANGE NOTE
PER SAES-L-105 RATING SYMBOL (NOTE 68) (Note 20) [mm] TRIM PACKING MAT,L RANGE [PSIG] TYPE (% PERCENTAGE)
(NOTE 86) ISO 15156 TYPE [Inch]
(NOTE 22) GROUP [DEG F]
RT MT PT VT
SHOP FIELD
WELD WELD
HYDROCARBON PROCESS - WET SOUR
H2S
SOUR WATER SOW NO
SOUR WATER SOW1 YES
SOUR WATER SOW3 YES
PRESSURISED SEWER PS2 YES FV UPTO 6" 0.5”-24”
PRESSURISED SEWER PS3 YES ASME B16.5 HV ABOVE 8"
SOUR WATER SOW2 NO FV ABOVE 8" (ALT)
MONO ETHYLENE GLYCOL MEG NO ASTM A105N
LIQUID ASTM A106 GR B FEXIBLE ASTM A105N ASTM A105N A193 GR B7M 316L SS SPW / BA, CH, GA,
00 1CT2P06 150 SLOP OIL (INCLUDING OIL SLUDGE) B31.3 N NO YES YES YES ASTM A234 WPB -S 3.2 TRIM 12 1.1 BW, WN RF 32 to 644 10% 10% 100% NONE 100% 1, 17
SPO VAPOUR NO API-5L-GR.B PSL2 – SAW GRAPHITE ASTM A350 LF2 CL2 ASTM A216 WCB A194 GR 2HM GRAPHITE GL, BU
HYDROCARBON ASTM A234 WPB-W
ACID GAS AG YES
ACID GAS AG3 YES
60 PSIG LLP STEAM 60S YES 220 PSIG @ 300 DEG F
HV 26” – 48"
PROCESS WATER PW YES 155 PSIG @ 405 DEG F
FV UPTO 30" (ALT)
LOW PRESSURE FLARE LPF YES 51 PSIG @ 350 DEG F
PRESSURISED SEWER PS YES 51 PSIG @ 644 DEG F
PRESSURISED SEWER PS1 YES 51 PSIG @ 644 DEG F HV 52" - 60"
HYDROCARBON PROCESS - WET SOUR
H2S - CATEGORY M SERVICE
ACID GAS AG1 ASTM A105N ASME B16.5 HV 0.5"-24”
ASTM A106 GR B FEXIBLE ASTM A105N ASTM A105N A193 GR B7M 316L SS SPW / BA, CH, GA,
00 1CT2P09 150 ACID GAS AG2 B31.3 VAPOUR M YES YES YES YES YES ASTM A234 WPB -S 3.2 TRIM 12 1.1 BW, WN RF 32 to 644 100% 100% 100% NONE 100% 1, 17
API-5L-GR.B PSL2 - SAW GRAPHITE ASTM A350 LF2 CL2 ASTM A216 WCB A194 GR 2HM GRAPHITE GL, BU, PL
ASTM A234 WPB-W 0
LOW PRESSURE FLARE LPF 185 PSIG @ 350 F
HV 26” – 60"
RELIEF LINE RL 51 PSIG @ 6440 F
HYDROCARBON PROCESS - WET SOUR
ASTM A105N FEXIBLE ASTM A105N A193 GR B7M 316L SS SPW / BA, CH, GA,
00 1CT2P12 150 H2S - AMINE SERVICE B31.3 LIQUID N NO NO YES YES YES ASTM A106 GR B 3.2 TRIM 12 1.1 ASTM A105N BW, WN RF 32 to 380 ASME B16.5 -0.081 PSIG 0.5"-18” 10% 10% 100% NONE 100% 1, 17, 88
ASTM A234 WPB -S GRAPHITE ASTM A216 WCB A194 GR 2HM GRAPHITE GL, BU
METHYL DETHANOL AMINE MDEA
PROCESS SERVICE - BELOW GROUND RTR EPOXY AS PER 01-SAMSS- AL- FEXIBLE RTR EPOXY AS PER Ductile Iron A395 32 to 200 A307 Gr B 1, 17, 27,
00 1FE0P01 150 B31.3 LIQUID - NO NO NO NO NO RTR EPOXY AS PER 01-SAMSS-034 0 ˗ 01-SAMSS-034 FF 50 FV BUNA-N 1"-12” CH, GA, GL NONE NONE NONE NONE 100%
034 BRONZE GRAPHITE 01- SAMSS-034 epoxy lined 180 A563 Gr A 76
SOUR WATER SOW
UTILITY SERVICE - BELOW GROUND
OILY WATER SEWER OWS
RTR EPOXY AS PER 01-SAMSS-034
WTP RTR EPOXY AS PER RTR EPOXY AS PER AL- FEXIBLE Ductile Iron A395 32 to 200 A307 Gr B 1, 17, 27,
00 1FE0U01 150 B31.3 LIQUID - NO NO NO NO NO 0 ˗ 01- SAMSS-034, 01- / 01-SAMSS- FF 50 FV BUNA-N 1"-72” CH, GA, GL NONE NONE NONE NONE 100%
SANITARY WATERSEWER SWS 01-SAMSS-034, 01-SAMSS-029 01-SAMSS-034, 01-SAMSS-029 BRONZE GRAPHITE epoxy lined 180 A563 Gr A 76
SAMSS-029 029
WATER W
ASTM B462
NO ASTM B729 UNS N08020 (Ann) - FEXIBLE ASTM B462 UNS A193 Gr.B7M PTFE + ARIMID
00 1NT0A02 150 60 PSIG LLP STEAM 60S B31.3 LIQUID N NO NO YES NO ASTM B366-WP20CB-S (Ann) 0 TRIM 13 3.17 Gr.N08020 BW, WN RF 32 to 395 ASME B16.5 FV 0.5"-4” CH, GA, GL 100% 100% NONE 100% 100% 1, 17, 23
YES SMLS GRAPHITE N08020 (Ann) A194 Gr 2HM INSERT
ASTM A351 Gr.CN7M
58 of 64
APPENDIX 1 PROJECT TITLE : FADHILI GAS PLANT
DOCUMENT NO. : D44-A-RE-585265 REV 00
PIPE CLASS SERVICE INDEX CLIENT: SAUDI ARAMCO
NEW PIPE CLASS ASME DESIGN
FLUID NACE FLANGE SIZE
DESIGNATION AS CLASS FLUID LETHAL PWHT CA VALVE VALVE B16.5 TEMP DESIGN PRESS RANGE VALVE NDE EXTENT
REV. SERVICE DESCRIPTION Code Fluid CATEGORY TOXIC HIC MR0175- PIPE MATERIAL FITTING MATERIAL FLANGE MATL. VALVE MATL. CONSTRUCT FACE EXTERNAL PRESSURE BOLTING GASKET (S) RANGE NOTE
PER SAES-L-105 RATING SYMBOL (NOTE 68) (Note 20) [mm] TRIM PACKING MAT,L RANGE [PSIG] TYPE (% PERCENTAGE)
(NOTE 86) ISO 15156 TYPE [Inch]
(NOTE 22) GROUP [DEG F]
RT MT PT VT
SHOP FIELD
WELD WELD
CHEMICAL SERVICE / INJECTION
HYDROCARBON PROCESS/UTILITY
SW Duplex SS
ASTM A182 F51 UNS FEXIBLE A182 F51 32 to 190 A193 Gr.B7 CH, GA, GL,
00 1SP0P01 150 MONO ETHYLENE GLYCOL MEG B31.3 LIQUID N NO NO NO NO NO ASTM A790 UNS S31803 - SMLS 0 2.8 ASTM A182 F51 SW, BW, WN RF ASME B16.5 HV S31803 Windings, 0.5”-12” 100% 100% NONE 100% 100% 1, 17
ASTM A815 WP-S UNS S31803 S31803 GRAPHITE A890 Gr.4A CD3MN 230 A194 Gr 2H BA
F/Graph 316 O'tr
PRESSURISED SEWER PS
HYDROCARBON PROCESS - WET SOUR SW Duplex SS
H2S ASTM A182 F51 UNS FEXIBLE A182 F51 A193 Gr.B7M
00 1SP0P02 150 B31.3 LIQUID N NO NO NO YES NO ASTM A790 UNS S31803 - SMLS 0 2.8 ASTM A182 F51 BW, WN RF 32 to 230 ASME B16.5 S31803 Windings, 0.5”-12” CH, GA, GL 100% 100% NONE 100% 100% 1, 17
ASTM A815 WP-S UNS S31803 S31803 GRAPHITE A890 Gr.4A CD3MN A194 Gr 2HM
SOUR WATER SOW F/Graph 316 O'tr
00 HYDROCARBON PROCESS - NON SOUR ASTM A105N FEXIBLE ASTM A105N A193 GR B7 316L SS SPW / BA, CH, GA,
3CS2P01 300 B31.3 LIQUID N NO NO NO NO NO ASTM A106 GR B 3.2 TRIM 8 1.1 ASTM A105N SW, BW, WN RF 32 to 392 ASME B16.5 0.5”-16” 10% 10% 100% NONE 100% 1, 17
SULFUR SF ASTM A234 WPB-S GRAPHITE ASTM A216 WCB A194 GR 2H GRAPHITE GL
SOUR WATER SOW ASTM A182- F316/316L 284 PSIG @ 190 DEG F
ASTM A312 TP316/316L - SMLS FEXIBLE ASTM A182- A182 F316/316L 32 to 290 A193 Gr.B7M 316L SS SPW /
00 3SD0P02 300 B31.3 LIQUID N NO NO NO YES NO ASTM A403 WP316/316L-S 0 TRIM 12 2.2 BW, WN RF CH, GA, GL 10% 10% NONE 100% 100% 1, 17
ASTM A358 TP316/316L CL.1 - EFW GRAPHITE F316/316L A351 CF8M 460 A194 Gr 2HM GRAPHITE
SOUR WATER SOW1 ASTM A403 WP316/316L-WX 300 PSIG @ 290 DEG F
3” – 18”
SOUR WATER SOW2 407 PSIG @ 284 DEG F
SOUR WATER SOW3 320 PSIG @ 460 DEG F
HYDROCARBON PROCESS - WET SOUR
ASTM A182- F316/316L ASME B16.5 0.5"-2”
H2S ASTM A312 TP316/316L - SMLS FEXIBLE ASTM A182- A182 F316/316L A193 Gr.B7M 316L SS SPW / CH, GA, GL,
00 3SD0P11 300 B31.3 LIQUID N NO NO NO YES NO ASTM A403 WP316/316L-S 0 TRIM 12 2.2 BW, WN RF 32 to 350 10% 10% NONE 100% 100% 1, 17, 88
ASTM A358 TP316/316L CL.1 - EFW GRAPHITE F316/316L A351 CF8M A194 Gr 2HM GRAPHITE BA
METHYL DETHANOL AMINE MDEA ASTM A403 WP316/316L-WX 300 PSIG @ 350 DEG F 3” – 18”
UTILITY STEAM7 & HC UTILITY SERVICE ASTM A105N ASTM A105N ASME B16.5 FV 0.5"-6”
VAPOUR \ ASTM A106 GR B FEXIBLE ASTM A105N A193 GR B7 316L SS SPW / CH, GA, GL,
00 6CS1U01 600 600 PSIG HP STEAM 600S B31.3 N NO NO NO NO NO ASTM A234 WPB-S 1.6 TRIM 5 1.1 ASTM A350 GR LF2 SW, BW, WN RF 32 to 750 10% 10% 100% NONE 100% 1, 17
LIQUID API-5L-GR.B PSL 2 - SAW GRAPHITE ASTM A216 WCB A194 GR 2H GRAPHITE BA
ASTM A234 WPB-W CL 2 730 PSIG FV 8” – 36”
600 PSIG H.P. CONDENSATE 600C
HYDROCARBON PROCESS - NON SOUR
OIL & OIL PRODUCTS P ASME B16.5 0.5”-8"
ASTM A105N FEXIBLE ASTM A105N A193 GR B7 316L SS SPW / BA, CH, GA,
00 6CS2P01 600 OIL & OIL PRODUCTS P1 B31.3 LIQUID N NO NO NO NO NO ASTM A106 GR B 3.2 TRIM 8 1.1 ASTM A105N SW, BW, WN RF 32 to180 10% 10% 100% NONE 100% 1, 17
ASTM A234-WPB -S GRAPHITE ASTM A216 WCB A194 GR 2H GRAPHITE GL
PRESSURISED SEWER PS
1200 PSIG 10" - 10"
FLUSHING OIL FLO
UTILITY STEAM SERVICE
BOILER BLOWDOWN BBD ASME B16.5 FV 0.5"-8”
LIQUID ASTM A105N FEXIBLE ASTM A105N A193 GR B7 316L SS SPW / CH, GA, GL,
00 6CS2U01 600 BOILER FEED WATER BFW B31.3 N NO NO NO NO NO ASTM A106 GR B 3.2 TRIM 5 1.1 ASTM A105N SW, BW, WN RF 32 to 750 10% 10% 100% NONE 100% 1, 17
VAPOUR ASTM A234 WPB-S GRAPHITE ASTM A216 WCB A194 GR 2H GRAPHITE BA
600 PSIG H.P. CONDENSATE 600C
730 PSIG FV 10"-18"
600 PSIG H. P. STEAM 600S
CHEMICAL SERVICE / INJECTION
CHEMICAL PHOSPHATE C1
FEXIBLE ASTM A182- A193 Gr.B7 316L SS SPW /
00 6SD0U01 600 CHEMICAL SULPHATE [ORGANIC B31.3 LIQUID N NO NO NO NO NO ASTM A312 TP316/316L - SMLS ASTM A182 F316/316L 0 TRIM 12 2.2 A182 F316/316L BW, WN RF 32 to 180 ASME B16.5 0.5"-1.5" 2" CH, GA, GL 10% 10% NONE 100% 100% 1, 17
GRAPHITE F316/316L A194 Gr 2H GRAPHITE
OXYGEN SCAVENGER (SULPHITE), C
NUETRALIZED AMINE (SULPHITE)]
HYDROCARBON PROCESS - WET SOUR
H2S DUPLEX - SW Duplex SS
ASTM A182 F51 FEXIBLE A182 F51 A193 Gr.B7M
00 6SP0P02 600 SOUR WATER SOW B31.3 LIQUID N NO NO NO YES NO ASTM A790 UNS S31803 - SMLS 0 UNS 2.8 ASTM A182 F51 BW, WN RF 32 to 230 ASME B16.5 S31803 Windings, 0.75"-6” CH, GA, GL 100% 100% NONE 100% 100% 1, 17
ASTM A815 WP-S UNS S31803 GRAPHITE A890 Gr.4A CD3MN A194 Gr 2HM
31803 F/Graph 316 O'tr
PRESSURISED SEWER PS
CLASS 900, 5Cr-1/2
UTILITY STEAM SERVICE ASME B16.5 0.75"-12”
ASTM A182-GR. F22 CL.3 FEXIBLE ASTM A182-GR. F22 A182 F22 CL.3 A193 GR B16 Mo OCTAGONAL
00 9CK1U01 900 B31.3 VAPOUR N NO NO NO NO NO ASTM A335-GR. P22 - SMLS 1.6 TRIM 5 1. 10 SW, BW, WN RJ 32 to1000 FV CH, GA, GL 100% 100% 100% NONE 100% 1, 17, 55
ASTM A234 GR. WP22 - SMLS GRAPHITE CL 3 A217 WC9 A194 GR 4 RING TYPE R, AS
600 PSIG HP STEAM 600S 730 PSIG PER ASME B16.20 14” – 16”
59 of 64
APPENDIX 1 PROJECT TITLE : FADHILI GAS PLANT
DOCUMENT NO. : D44-A-RE-585265 REV 00
PIPE CLASS SERVICE INDEX CLIENT: SAUDI ARAMCO
GENERAL NOTES
Sr. No. Description
1 Additional valves shall be added to individual pipe classes when specified.
2 a. The service designations are based on Saudi Aramco corporate requirements.
b. The pipe class designation are based upon Saudi Aramco corporate requirements with an additional two digit suffix to include project specific requirements ;
3 No copper alloys permitted.
4 Utility services may have been added to process pipe class designations to reduce / consolidate the number of pipe classes required.
5 DELETED
6 DELETED
7 Underground metal piping system shall be externally protected in accordance with the project Specification For External Coating (D44-H-RE-380909) and with CP as per Specification for Cathodic Protection D44-X-RE-380913).
8 All nonmetallic gaskets with a filler shall be manufactured with oil resistant binder.
9 Spiral wound gaskets shall be with inner ring of SS316L as a minimum or equivalent to base piping class material grade and outer ring in carbon steel.
10 In general Ball valves shall be soft seated, regular port. Full port ball valve requirements shall be specified on the P&ID.
11 All Globe valves shall be non regulating disc type.
12 Flange facing finish shall be as per ANSI B 16.5
13 DELETED
14 Insulating Gasket Kits shall be considered for dissimilar material joints wherever indicated in P&IDs.
15 Ignition lines from the flame front generator panel to the flare tip shall be manufactured from type 316 stainless steel. In accordance to SAES-F-007, paragraph 6.19.2.
16 Pipe Classes 1CX4P01, 1CX4P06, 1CX4P09, 1CX4P20 & 1SX4P02 to include Full Jacket Gate, Check, Plug Valves in addition to the standard Gate, Check and Plug Valves
17 This piping class is based on the existing SAES-L-105 Piping Line Class.
18 Flat gasket i.e. "SPECIAL FLAT NON MET GASKET (PTFE - REINFOCED)" can be used with a RTJ flange.
19 Pipe Class Material Designator "PK" has been selected for PVDF material in accordance with Project Industry Practices PIP PNCM0001 as per SAES-L-105 section 8.
Where PWHT is defined as "YES" this indicates that all welds including those made in manufacture and repair require PWHT.
20 Where PWHT is defined as "NO" this indicates that all welds including those made in manufacture and repair do not require PWHT according to the services and process requirements. However, PWHT shall be performed in all
welds whether it is required as per the applicable Code and SAES-L-105, SAES-W-011 and SAES-W-012.
21 ASME B16.5 Material Group 1.3 has been identified to allow the use of ASTM A352 Gr.LCB Cast Valves
22 Designation of piping classes are in accordance with SAES-L-105 (7 July 2013).
23 ASME B16.5 Material Group 3.17 has been identified to allow the use of ASTM A351 Gr.CN7M Solution Annealed Cast Valves
24 Unless specified otherwise all SS SPW Gaskets to be Type316L
25 The Corrosion Allowance for Pipes in Molten Sulfur Service to be as follows: For Steam Traced, Contro-Traced or Electric Traced Lines. a) Minimum CA 3.2mm, b) Maximum CA 6.4mm, For Jacketed Lines Minimum CA 6.4 mm
26 DELETED
27 When joining Adhesive Bonded Pipes adhesive to be uniformly applied with no excess secretions
28 DELETED
29 DELETED
30 DELETED
Pipe Line Classes 1CG0U01(Instrument Air), 80CG0D01(Vents), 1CS1P01(Diesel Fuel), 1CS1U01(Utility Air), 1CT2P06(Amine Solvent HS-102Drain), (HC Drain) and 1SV0P02 (MEG/Oily Water) when used Belowground to be
31
Cathodically Protected in accordance with Specification for Cathodic Protection (D44-X-RE-380913) SA Engineering Standard, SAES-X-600, Cathodic Protection of Plant Facilities.
32 DELETED
33 DELETED
34 HIC Testing not required for Seamless Pipe.
60 of 64
APPENDIX 1 PROJECT TITLE : FADHILI GAS PLANT
DOCUMENT NO. : D44-A-RE-585265 REV 00
PIPE CLASS SERVICE INDEX CLIENT: SAUDI ARAMCO
GENERAL NOTES
Sr. No. Description
35 Pipe Class Designation – Normally Suffix 06 is added for Sour Service NACE requirement and HIC resistant carbon steels.
36 DELETED
Pipe Line Classes 1CG0U01 (Instrument Air), 80CG0D01 (Vents), 1CS1P01 (Diesel Fuel),1CS1U01 (Utility Air), 1CT2P06 (Amine Solvent HS-102 Drain) and (HC Drain) and 1SV0P02 (MEG/Oily Water) when used Belowground to
37
be Externally Coated in accordance with SA Engineering Standard, SAES-H-002, Internal and External Coatings for Steel Pipelines and Piping
38 Internal Fusion Bonded Epoxy Coating as per Project Specification for Internal Lining (D44-H-RE-380908).
39 DELETED
40 DELETED
41 DELETED
42 DELETED
43 DELETED
44 DELETED
45 DELETED
46 DELETED
47 DELETED
48 DELETED
49 DELETED
50 DELETED
51 DELETED
52 DELETED
53 DELETED
54 DELETED
55 Pipe Class 9CK1U01 used for High Pressure Superheated Steam from 750 Deg F to 1050 Deg F only (Shell Licensor Pipe Class)
56 GRE Class150 Flanges required to suit design pressure/temperature rating 234psig @ 180 Deg F
57 For pipe classes 1CG0U01 & 80CG0D01, shop galvanized for line size 3" and smaller. For line size 4" and above, galvanized after spool fabricated.
58 For Sulphur-Molten Service in Pipe Class 1CS2P01 and 3CS2P01 use Gate, Check and Plug Valves
59 DELETED
60 DELETED
61 DELETED
62 Steam Jacket to be designed at least one size larger than the inner pipe.
63 Jacket pipe is designed for low pressure steam (95 psig @ 395 deg F) with1.6 mm corrosion allowance
64 DELETED
65 DELETED
66 DELETED
67 DELETED
Pipe Classes identified as “LETHAL” shall be considered as Category M services and shall be designed to ASME B31.3, Chapter VIII requirements. Valves in Category M service shall be fugitive emission type tested as per ISO
68
15848-1 with Helium as test medium.
69 DELETED
70 DELETED
61 of 64
APPENDIX 1 PROJECT TITLE : FADHILI GAS PLANT
DOCUMENT NO. : D44-A-RE-585265 REV 00
PIPE CLASS SERVICE INDEX CLIENT: SAUDI ARAMCO
GENERAL NOTES
Sr. No. Description
71 DELETED
72 DELETED
73 DELETED
74 DELETED
75 DELETED
76 Joint type to be used in RTR Epoxy piping shall be adhesive joint socket x spigot (taper) up to 24" size and Laminated joint for sizes 26" & above. Suitability of joint type shall be confirmed with RTR vendor.
77 DELETED
78 DELETED
The using of soft seat valves is limited to clean services within design conditions covered by Saudi Aramco Standards and Project Documentation. Metal seat valves shall be used whenever is required by design and fluid conditions
79
such as high temperature services or fluids containing solid particles as identified in P&IDs.
80 DELETED
81 DELETED
82 DELETED
83 Small sizes of FBE lines shall be 6Mo of a grade suitable for the service
84 DELETED.
85 Nondestructive Examination requirements and extent shall be as per SAES-W-011. Extent of Radiography shall be as per SAES-W-011, clause 17.6.2.1 based on Service category identified against each pipe class.
86 Fluid Category N/M/D shall be as defined in ASME B31.3.
87 The elastomeric gasket used shall comply requirements as per D44-A-RE-380920.
88 Sealing material requirement for Amine Service shall be as per Project Specification Material Requirement for CS and Low Alloy Steel (For piping, fittings, flanges & valves), Doc.No. D44-A-RE-380920.
GL = Globe LJ = Lap Joint FLANGE FACE TYPE LTCS = Low Temperature Carbon Steel (Impact tested).
62 of 64
EDSD REV
REVISION
REVISIONCERTIFICATION
CERTIFICATE VERIFICATION NO. DATE JO/EWO DESCRIPTION ENGG CERT PMT OPRNS
00
DATE:
DATE:
DATE:
DATE:
DATE:
THIS INDICATES THAT REV. NO.__________ BI-10-
TNP
LEAD
OF THIS DRAWING IS COVERED, FOR ALL B 04AUG16 01900-0004 RE-ISSUED FOR REVIEW RAG RSJ
RAG
CONTROL NUMBER
APPROVAL/CERTIFICATION REQUIREMENTS, 29SEPT16 BI-10-
/ RAG
RAG RSJ
ENGINEER
00 01900-0004 ISSUED FOR DESIGN
AGENCY
NLP / SSK
/ RD
BY:
PROJECT
BY DRAWING COMPLETION CERTIFICATE
ENGINEER
ENGINEER
PB / RSJ / KR
DISCIPLINE
CERTIFIED
29/09/2016
29/09/2016
29/09/2016
OPERATIONS
CONSTRUCTION
(DCC) NO. _____________________ DATE:
``
SAUDI ARABIA
D44
JO / EWO:
A
DWG.TYPE PLANT NO. INDEX
SAUDI ARABIAN OIL COMPANY
BI-10-01900-0004
DRAWING NO.
RE- 585265
64
63
OF
SHT. NO.
D44-A-RE-585265 Rev00.doc
00
REV. NO.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Sch/WT Sch160 Sch160 XS XS XS STD STD STD STD STD STD STD
Size 16 18 20 24
1 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
2 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Sockolet 2 - 24 * 1/2 - 3/4 CL 6000 MSS SP-97 ASTM A350 GR LF2 CL1 OLTS000008C
Sockolet 3 - 24 * 1 - 1.1/2 CL 3000 MSS SP-97 ASTM A350 GR LF2 CL1 OLTS000007C
3 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Flange WN 2 - 24 CL 300 WN RF ASME B16.5 ASTM A350 GR LF2 CL1 FLGW000034C 2,6
Flange SW 1/2 - 1.1/2 CL 150 SW RF ASME B16.5 ASTM A350 GR LF2 CL1 FLGS000004C 2
Flange SW 1/2 - 1.1/2 CL 300 SW RF ASME B16.5 ASTM A350 GR LF2 CL1 FLGS000005C 2,6
Blind Flange 1/2 - 24 CL 150 RF ASME B16.5 ASTM A350 GR LF2 CL1 FLGB000032C 2
4 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
5 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
6 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.3 of ASME B16.5 upto NPS 24.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
7 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
8: Valves for low temperature service shall confirm to the requirements of 04-SAMSS-003.
9: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
10: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the valve
at valve vendor shop.
11: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
12: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
8 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T4 T4 T1 T1 T
3 T4 T4 T4 T1 T1 T
4 T4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
14 T4 T4 T4 T4 T3 T3 T3 T3 T3 T1 T1 T
16 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
24 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T
ABBREVIATIONS:
9 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, 60 PSIG LLP STEAM, UTILITY WATER
Pipe Material: LTCS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
SERVICE LIMITS
Size Range 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 26-76 26-76 26-76 26-76
Temperature (ºF) - -50 100 200 300 400 460 - 180 350 460
FV-4",
HV-6" to
HV up to
Pressure (Psig) 16", HV- 265 265 255 230 200 182 240 160 102
56" (Alt)
18" to
24" (Alt)
Sch/WT XXS XXS Sch160 Sch160 Sch160 XS XS STD STD STD STD
Size 12 14 16 18 20 24 26 28 30 32 34 36
Sch/WT STD STD STD STD STD STD Sch10 8.74mm 8.74mm 8.74mm 8.74mm STD
Size 38 40 42 46 48 52 56 56 60 64 68 72
Sch/WT STD 10.31mm 10.31mm 11.13mm 11.13mm 11.91mm 12.70mm 14.27mm 14.27mm 14.27mm 14.27mm 15.09mm
Size 76
Sch/WT 15.09mm
10 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, 60 PSIG LLP STEAM, UTILITY WATER
Pipe Material: LTCS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
11 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, 60 PSIG LLP STEAM, UTILITY WATER
Pipe Material: LTCS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
12 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, 60 PSIG LLP STEAM, UTILITY WATER
Pipe Material: LTCS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
13 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, 60 PSIG LLP STEAM, UTILITY WATER
Pipe Material: LTCS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
14 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, 60 PSIG LLP STEAM, UTILITY WATER
Pipe Material: LTCS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
15 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, 60 PSIG LLP STEAM, UTILITY WATER
Pipe Material: LTCS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
16 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, 60 PSIG LLP STEAM, UTILITY WATER
Pipe Material: LTCS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
17 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, 60 PSIG LLP STEAM, UTILITY WATER
Pipe Material: LTCS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
18 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, 60 PSIG LLP STEAM, UTILITY WATER
Pipe Material: LTCS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
19 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, 60 PSIG LLP STEAM, UTILITY WATER
Pipe Material: LTCS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
20 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, 60 PSIG LLP STEAM, UTILITY WATER
Pipe Material: LTCS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
Notes
1: This pipe class is designed for full rating as per Group 1.3 of ASME B16.5 upto NPS 24. For NPS 26 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in
P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Valves for low temperature service shall confirm to the requirements of 04-SAMSS-003.
8: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
9: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
10: All material shall meet the requirements of NACE MR0175/ISO 15156.
11: All welds for all wall thicknesses including those made in manufacture and repair shall require PWHT.
12: Flanges, Blind Flanges not covered by ASME B16.5 / ASME B16.47 shall be designed and fabricated according to ASME VIII, div. 1. Refer
Appendix 3 for Special flange drawings.
13: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
14: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
21 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, 60 PSIG LLP STEAM, UTILITY WATER
Pipe Material: LTCS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
16: Alternate wall thickness (14.27mm) for NPS 56 is considered for piping portion with half vacuum as indicated in P&ID.
22 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, 60 PSIG LLP STEAM, UTILITY WATER
Pipe Material: LTCS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T3 T3 T1 T1 T
3 T3 T3 T3 T1 T1 T
4 T3 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T3 T1 T1 T
8 T3 T3 T3 T3 T3 T3 T1 T1 T
10 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
12 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
14 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
16 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
24 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T
30 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR T1 T1 T1 T1 T
36 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR T1 T1 T1 T
40 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T
42 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T1 T
48 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T
52 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T
56 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T1 T
60 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T
64 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T
68 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T
72 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T
76 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T1 T
1 TLR TLR TL
1.1/2 TLR TLR TLR TL
2 T8 T8 TLR TLR TL
3 T8 T8 T8 TLR TLR TL
4 T8 T8 T8 T8 TLR TLR TL
6 T8 T8 T8 T8 T8 TLR TLR TL
8 T8 T8 T8 T8 T8 T8 TLR TLR TL
10 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
12 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
14 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
16 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
18 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
20 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TLR TL
24 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TLR TLR TL
30 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TLR TLR TLR TLR TL
36 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TLR TLR TLR TL
40 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TLR TLR TLR TL
42 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TL
48 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TL
52 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TL
56 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TL
60 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TLR TL
64 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TLR TL
68 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TLR TLR TL
72 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TLR TLR TL
76 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TLR TLR TLR TL
ABBREVIATIONS:
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
TL: Equal Tee - 45 Deg
TLR: Reducing Tee - 45 Deg
TR1: Stub in Connection with Full encirclement sleeve - 45 Deg
T8: Latrolet
23 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Size Range 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 26-76 26-76 26-76 26-76
Temperature (ºF) -50 100 200 300 400 460 - 180 350 460
HV up to
30", HV-
Pressure (Psig) 265 265 255 230 200 182 240 160 102
32" to
76" (Alt)
Sch/WT XXS XXS Sch160 Sch160 Sch160 XS XS STD STD STD STD
Size 14 16 18 20 24 26 28 30 32 34 36
Sch/WT STD STD STD STD STD 8.74mm 8.74mm STD 8.74mm 8.74mm STD
Size 38 40 42 44 46 48 52 56 60 64 68 72
Sch/WT STD 10.31mm 10.31mm 10.31mm 11.13mm 11.13mm 11.91mm 12.70mm 14.27mm 14.27mm 14.27mm 15.09mm
Size 74 76 76
24 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
25 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
26 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
27 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
28 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
29 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
30 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
31 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
32 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
33 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
34 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
35 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
36 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.3 of ASME B16.5 upto NPS 24. For NPS 26 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Valves for low temperature service shall confirm to the requirements of 04-SAMSS-003.
8: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
9: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
10: All material shall meet the requirements of NACE MR0175/ISO 15156.
11: All welds for all wall thicknesses including those made in manufacture and repair shall require PWHT.
12: Flanges, Blind Flanges not covered by ASME B16.5 / ASME B16.47 shall be designed and fabricated according to ASME VIII, div. 1. Refer
Appendix 3 for Special flange drawings.
13: This pipe class is applicable for Category M service and shall comply to ASME B31.3, Chapter VIII requirements.
14: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Helium.
16: Alternate wall thickness (17.48mm) for NPS 76 is considered for piping portion with half vacuum as indicated in P&ID.
37 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CA2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: LOW PRESSURE FLARE, HIGH PRESSURE FLARE
Pipe Material: LTCS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic, Lethal Service
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T3 T3 T1 T1 T
3 T3 T3 T3 T1 T1 T
4 T3 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T3 T1 T1 T
8 T3 T3 T3 T3 T3 T3 T1 T1 T
10 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
12 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
14 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
16 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
24 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T
26 T3 T3 T3 T3 T3 T3
28 T3 T3 T3 T3 T3 T3
30 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR T1 T1 T1 T1 T
32 T3 T3 T3 T3 T3 T3
34 T3 T3 T3 T3 T3 T3
36 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR T1 T1 T1 T
38 T3 T3 T3 T3 T3 T3
40 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T
42 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T1 T
44 T3 T3 T3 T3 T3 T3
46 T3 T3 T3 T3 T3 T3
48 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T
52 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T
56 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T1 T
60 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T
64 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T
68 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T
72 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T
76 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
3/4 TLR TL
1 TLR TLR TL
1.1/2 TLR TLR TLR TL
2 T8 T8 TLR TLR TL
3 T8 T8 T8 TLR TLR TL
4 T8 T8 T8 T8 TLR TLR TL
6 T8 T8 T8 T8 T8 TLR TLR TL
8 T8 T8 T8 T8 T8 T8 TLR TLR TL
10 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
12 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
14 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
16 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
18 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
20 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TLR TL
24 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TLR TLR TL
30 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TLR TLR TLR TLR TL
36 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TLR TLR TLR TL
40 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TLR TLR TLR TL
42 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TL
48 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TL
52 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TL
56 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TL
60 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TLR TL
64 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TLR TL
68 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TLR TLR TL
72 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TLR TLR TL
76 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TLR TLR TLR TL
ABBREVIATIONS:
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
TL: Equal Tee - 45 Deg
TLR: Reducing Tee - 45 Deg
TR1: Stub in Connection with Full encirclement sleeve - 45 Deg
T8: Latrolet
38 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CG0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Elbow 45 deg 1/2 - 1/2 CL 6000 NPT(F) ASME B16.11 ASTM A105N galv ELGF000027C
Elbow 45 deg 3/4 - 3 CL 3000 NPT(F) ASME B16.11 ASTM A105N galv ELGF000023C
Elbow 90 deg 1/2 - 1/2 CL 6000 NPT(F) ASME B16.11 ASTM A105N galv ELGN000071C
Elbow 90 deg 3/4 - 3 CL 3000 NPT(F) ASME B16.11 ASTM A105N galv ELGN000068C
39 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CG0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Tee equal 1/2 - 1/2 CL 6000 NPT(F) ASME B16.11 ASTM A105N galv TEGE000014C
Tee equal 3/4 - 3 CL 3000 NPT(F) ASME B16.11 ASTM A105N galv TEGE000006C
Tee reducing 3/4 - 1.1/2 CL 6000 NPT(F) ASME B16.11 ASTM A105N galv TEGR000021C
Tee reducing 1-3 CL 3000 NPT(F) ASME B16.11 ASTM A105N galv TEGR000013C
Cap 1/2 - 1/2 CL 6000 NPT(F) ASME B16.11 ASTM A105N galv CAPG000027C
Cap 3/4 - 3 CL 3000 NPT(F) ASME B16.11 ASTM A105N galv CAPG000022C
40 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CG0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Plug hex head 1/2 - 1.1/2 NPT(M) ASME B16.11 ASTM A105N galv PLGH000017C
Coupling Full 1/2 - 1/2 CL 6000 NPT(F) ASME B16.11 ASTM A105N galv CPLF000026C
Coupling Full 3/4 - 3 CL 3000 NPT(F) ASME B16.11 ASTM A105N galv CPLF000023C
Coupling reducing 3/4 - 1.1/2 CL 6000 NPT(F) ASME B16.11 ASTM A105N galv CPLR000048C
Coupling reducing 1-3 CL 3000 NPT(F) ASME B16.11 ASTM A105N galv CPLR000027C
Union 3/4 - 3 CL 3000 NPT(F) MSS SP-83 ASTM A105N galv CTRU000004C
Threadolet 4 - 6 * 1/2 - 1/2 CL 6000 NPT(F) MSS SP-97 ASTM A105N galv OLTT000037C
Threadolet 4 - 6 * 3/4 - 1.1/2 CL 3000 NPT(F) MSS SP-97 ASTM A105N galv OLTT000035C
41 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CG0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Blind Flange 1/2 - 3 CL 150 FF ASME B16.5 ASTM A105N galv FLGB000304C 2
Spectacle Blank 1/2 - 1.1/2 CL 150 FF ASME B16.48 ASTM A516 GR 70 galv LBKB000326C 2
42 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CG0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
43 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CG0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
44 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CG0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5.
2: The flange face finish of Flat Face flanges shall be in accordance with MSS SP-6, except otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
8: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
9: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
10: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
11: Pipe spool shall be galvanized after spool fabrication for sizes 4" and above.
45 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CG0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T1 T1 T
3 T1 T1 T
4 T5 T5 T5 T5 T1 T1 T
6 T5 T5 T5 T5 T3 T1 T1 T
ABBREVIATIONS:
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
46 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
80CG0D01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Elbow 45 deg 1/2 - 1/2 CL 6000 NPT(F) ASME B16.11 ASTM A105N galv ELGF000027C
Elbow 45 deg 3/4 - 3 CL 3000 NPT(F) ASME B16.11 ASTM A105N galv ELGF000023C
Elbow 90 deg 1/2 - 1/2 CL 6000 NPT(F) ASME B16.11 ASTM A105N galv ELGN000071C
47 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
80CG0D01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Elbow 90 deg 3/4 - 3 CL 3000 NPT(F) ASME B16.11 ASTM A105N galv ELGN000068C
Tee equal 1/2 - 1/2 CL 6000 NPT(F) ASME B16.11 ASTM A105N galv TEGE000014C
Tee equal 3/4 - 3 CL 3000 NPT(F) ASME B16.11 ASTM A105N galv TEGE000006C
Tee reducing 1-3 CL 3000 NPT(F) ASME B16.11 ASTM A105N galv TEGR000013C
48 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
80CG0D01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Cap 3/4 - 3 CL 3000 NPT(F) ASME B16.11 ASTM A105N galv CAPG000022C
Plug hex head 1/2 - 1.1/2 NPT(M) ASME B16.11 ASTM A105N galv PLGH000017C
Coupling Full 1/2 - 1/2 CL 6000 NPT(F) ASME B16.11 ASTM A105N galv CPLF000026C
Coupling Full 3/4 - 3 CL 3000 NPT(F) ASME B16.11 ASTM A105N galv CPLF000023C
Coupling reducing 1-3 CL 3000 NPT(F) ASME B16.11 ASTM A105N galv CPLR000027C
Union 3/4 - 1.1/2 CL 3000 NPT(F) MSS SP-83 ASTM A105N galv CTRU000004C
49 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
80CG0D01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Threadolet 4 - 6 * 3/4 - 1.1/2 CL 3000 NPT(F) MSS SP-97 ASTM A105N galv OLTT000035C
Blind Flange 1/2 - 3 CL 150 FF ASME B16.5 ASTM A105N galv FLGB000304C 2
50 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
80CG0D01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Spectacle Blank 1/2 - 1.1/2 CL 150 FF ASME B16.48 ASTM A516 GR 70 galv LBKB000326C 2
51 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
80CG0D01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
52 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
80CG0D01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5.
2: The flange face finish of Flat Face flanges shall be in accordance with MSS SP-6, except otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
53 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
80CG0D01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
8: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
9: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
10: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
11: Pipe spool shall be galvanized after spool fabrication for sizes 4" and above.
54 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
80CG0D01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T
1 T1 T
1.1/2 T1 T1 T
2 T1 T1 T
3 T1 T1 T
4 T5 T5 T5 T1 T1 T
6 T5 T5 T5 T3 T1 T1 T
ABBREVIATIONS:
55 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CH2C01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Elbow 90 deg 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGN000070C
56 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CH2C01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Nipoflange 2 - 2 * 3/4 - 3/4 CL 150 RF mfg std ASTM A105N 150mm long OLTF000288C 2
Blind Flange 1/2 - 1.1/2 CL 150 RF ASME B16.5 ASTM A105N FLGB000226C 2
57 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CH2C01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 24.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
5: Gate Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for process
drain/vent.
6: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
7: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
8: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
9: All welds for all wall thicknesses including those made in manufacture and repair shall require PWHT.
58 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CH2C01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
ABBREVIATIONS:
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
59 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CH2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Sch/WT XXS XXS Sch160 Sch160 Sch160 XS XS STD STD STD STD STD
Size 16 18 20 24
Elbow 45 deg 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGF000026C
Elbow 90 deg 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGN000070C
60 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CH2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Tee equal 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N TEGE000013C
Tee reducing 1.1/2 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N TEGR000017C
61 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CH2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Coupling reducing 1.1/2 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N CPLR000022C
Nipoflange 2 - 24 * 3/4 - 2 CL 150 RF mfg std ASTM A105N 150mm long OLTF000288C 2
Nipoflange 2 - 24 * 3/4 - 2 CL 150 RF mfg std ASTM A105N 200mm long OLTF000286C 2
Nipoflange 2 - 24 * 3/4 - 2 CL 300 RF mfg std ASTM A105N 200mm long OLTF000292C 2
Nipoflange 2 - 24 * 3/4 - 2 CL 300 RF mfg std ASTM A105N 150mm long OLTF000294C 2
62 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CH2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Flange SW 1/2 - 1.1/2 CL 300 SW RF ASME B16.5 ASTM A105N FLGS000002C 2,6
63 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CH2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Spectacle Blank 1/2 - 1.1/2 CL 150 FF ASME B16.48 ASTM A516 GR 70 LBKB000352C 2
64 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CH2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
65 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CH2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
66 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CH2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 24.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
8: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
9: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the
valve at valve vendor shop.
10: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
11: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
12: All welds for all wall thicknesses including those made in manufacture and repair shall require PWHT.
13: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
67 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CH2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T
1 T1 T
1.1/2 T1 T1 T
2 T4 T4 T1 T1 T
3 T4 T4 T4 T1 T1 T
4 T4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
14 T4 T4 T4 T4 T3 T3 T3 T3 T3 T1 T1 T
16 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
24 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T
3/4 TLR TL
1 TLR TLR TL
1.1/2 TLR TLR TLR TL
2 T8 T8 TLR TLR TL
3 T8 T8 T8 TLR TLR TL
4 T8 T8 T8 T8 TLR TLR TL
6 T8 T8 T8 T8 T8 TLR TLR TL
8 T8 T8 T8 T8 T8 T8 TLR TLR TL
10 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
12 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
14 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
16 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
18 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
20 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TLR TL
24 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TLR TLR TL
ABBREVIATIONS:
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
TL: Equal Tee - 45 Deg
TLR: Reducing Tee - 45 Deg
TR1: Stub in Connection with Full encirclement sleeve - 45 Deg
T8: Latrolet
68 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: FUEL GAS, LOW PRESSURE FUEL GAS, OIL & OIL PRODUCTS, NITROGEN, VENT GAS, PROCESS WATER
SERVICE LIMITS
Sch/WT Sch160 Sch160 XS XS XS STD STD STD STD STD STD STD
Size 16 18 20 24
Elbow 45 deg 1/2 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N ELGF000024C
Elbow 90 deg 1/2 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N ELGN000069C
69 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: FUEL GAS, LOW PRESSURE FUEL GAS, OIL & OIL PRODUCTS, NITROGEN, VENT GAS, PROCESS WATER
Tee equal 1/2 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N TEGE000010C
Tee reducing 3/4 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N TEGR000017C
Tee reducing 1.1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A105N TEGR000012C
70 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: FUEL GAS, LOW PRESSURE FUEL GAS, OIL & OIL PRODUCTS, NITROGEN, VENT GAS, PROCESS WATER
Coupling reducing 3/4 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N CPLR000022C
Coupling reducing 1.1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A105N CPLR000021C
Nipoflange 2 - 24 * 3/4 - 2 CL 150 RF mfg std ASTM A105N 150mm long OLTF000288C 2
Nipoflange 2 - 24 * 3/4 - 2 CL 150 RF mfg std ASTM A105N 200mm long OLTF000286C 2
Nipoflange 2 - 24 * 3/4 - 2 CL 300 RF mfg std ASTM A105N 200mm long OLTF000292C 2
Nipoflange 2 - 24 * 3/4 - 2 CL 300 RF mfg std ASTM A105N 150mm long OLTF000294C 2
71 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: FUEL GAS, LOW PRESSURE FUEL GAS, OIL & OIL PRODUCTS, NITROGEN, VENT GAS, PROCESS WATER
Flange SW 1/2 - 1.1/2 CL 300 SW RF ASME B16.5 ASTM A105N FLGS000002C 2,6
72 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: FUEL GAS, LOW PRESSURE FUEL GAS, OIL & OIL PRODUCTS, NITROGEN, VENT GAS, PROCESS WATER
Spectacle Blank 3/4 - 1.1/2 CL 150 FF ASME B16.48 ASTM A516 GR 70 LBKB000352C 2
73 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: FUEL GAS, LOW PRESSURE FUEL GAS, OIL & OIL PRODUCTS, NITROGEN, VENT GAS, PROCESS WATER
74 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: FUEL GAS, LOW PRESSURE FUEL GAS, OIL & OIL PRODUCTS, NITROGEN, VENT GAS, PROCESS WATER
75 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: FUEL GAS, LOW PRESSURE FUEL GAS, OIL & OIL PRODUCTS, NITROGEN, VENT GAS, PROCESS WATER
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 24.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
8: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
76 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: FUEL GAS, LOW PRESSURE FUEL GAS, OIL & OIL PRODUCTS, NITROGEN, VENT GAS, PROCESS WATER
9: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the
valve at valve vendor shop.
10: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
11: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
12: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
77 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: FUEL GAS, LOW PRESSURE FUEL GAS, OIL & OIL PRODUCTS, NITROGEN, VENT GAS, PROCESS WATER
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T4 T4 T1 T1 T
3 T4 T4 T4 T1 T1 T
4 T4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
14 T4 T4 T4 T4 T3 T3 T3 T3 T3 T1 T1 T
16 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
24 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T
ABBREVIATIONS:
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
78 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: INSTRUMENT AIR, NITROGEN, PROCESS AIR, RELIEF LINE, STEAM CONDENSATE (ATMOSPHERIC),
UTILITY AIR, VENT GAS, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE
SERVICE LIMITS
Size Range 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 26-42
Sch/WT Sch160 Sch160 XS XS XS STD STD STD STD STD STD STD
Size 16 18 20 24 26 28 30 32 36 38 40 42
Sch/WT STD STD STD STD Sch10 Sch10 Sch10 Sch10 Sch10 7.92mm 7.92mm 8.74mm
Size 46 48
Elbow 45 deg 1/2 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N ELGF000024C
79 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: INSTRUMENT AIR, NITROGEN, PROCESS AIR, RELIEF LINE, STEAM CONDENSATE (ATMOSPHERIC),
UTILITY AIR, VENT GAS, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE
Elbow 90 deg 1/2 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N ELGN000069C
Tee equal 1/2 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N TEGE000010C
Tee reducing 3/4 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N TEGR000017C
Tee reducing 1.1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A105N TEGR000012C
80 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: INSTRUMENT AIR, NITROGEN, PROCESS AIR, RELIEF LINE, STEAM CONDENSATE (ATMOSPHERIC),
UTILITY AIR, VENT GAS, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE
Plug hex head 1-1 NPT(M) ASME B16.11 ASTM A105N PLGH000016C
81 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: INSTRUMENT AIR, NITROGEN, PROCESS AIR, RELIEF LINE, STEAM CONDENSATE (ATMOSPHERIC),
UTILITY AIR, VENT GAS, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE
Pipe Nipple
Coupling reducing 3/4 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N CPLR000022C
Coupling reducing 1.1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A105N CPLR000021C
Nipoflange 2 - 48 * 3/4 - 2 CL 150 RF mfg std ASTM A105N 150mm long OLTF000288C 2
Nipoflange 2 - 48 * 3/4 - 2 CL 150 RF mfg std ASTM A105N 200mm long OLTF000286C 2
Nipoflange 2 - 48 * 3/4 - 2 CL 300 RF mfg std ASTM A105N 150mm long OLTF000294C 2
Nipoflange 2 - 48 * 3/4 - 2 CL 300 RF mfg std ASTM A105N 200mm long OLTF000292C 2
82 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: INSTRUMENT AIR, NITROGEN, PROCESS AIR, RELIEF LINE, STEAM CONDENSATE (ATMOSPHERIC),
UTILITY AIR, VENT GAS, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE
Flange WN 2 - 24 CL 900 WN RTJ ASME B16.5 ASTM A350 GR LF2 CL2 FLGW000464C 13
Flange SW 1/2 - 1.1/2 CL 150 SW RF ASME B16.5 ASTM A105N FLGS000001C 2,13
83 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: INSTRUMENT AIR, NITROGEN, PROCESS AIR, RELIEF LINE, STEAM CONDENSATE (ATMOSPHERIC),
UTILITY AIR, VENT GAS, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE
Flange SW 1/2 - 1.1/2 CL 1500 SW RTJ ASME B16.5 ASTM A105N FLGS000052C 13
Flange SW 1/2 - 1.1/2 CL 300 SW RF ASME B16.5 ASTM A105N FLGS000002C 2,6,13
Flange SW 1/2 - 1.1/2 CL 600 SW RF ASME B16.5 ASTM A105N FLGS000003C 2,6,13
Flange reducing
2-2 CL 150 SW RF ASME B16.5 ASTM A105N FLRS000012C
SW
Flange reducing
3 - 12 CL 150 WN RF ASME B16.5 ASTM A105N FLRW000010C 2,13
WN
84 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: INSTRUMENT AIR, NITROGEN, PROCESS AIR, RELIEF LINE, STEAM CONDENSATE (ATMOSPHERIC),
UTILITY AIR, VENT GAS, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE
Blind Flange 1/2 - 24 CL 300 RF ASME B16.5 ASTM A105N FLGB000228C 2,6
Spectacle Blank 3/4 - 1.1/2 CL 150 FF ASME B16.48 ASTM A516 GR 70 LBKB000352C 2
85 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: INSTRUMENT AIR, NITROGEN, PROCESS AIR, RELIEF LINE, STEAM CONDENSATE (ATMOSPHERIC),
UTILITY AIR, VENT GAS, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE
86 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: INSTRUMENT AIR, NITROGEN, PROCESS AIR, RELIEF LINE, STEAM CONDENSATE (ATMOSPHERIC),
UTILITY AIR, VENT GAS, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE
87 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: INSTRUMENT AIR, NITROGEN, PROCESS AIR, RELIEF LINE, STEAM CONDENSATE (ATMOSPHERIC),
UTILITY AIR, VENT GAS, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE
88 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: INSTRUMENT AIR, NITROGEN, PROCESS AIR, RELIEF LINE, STEAM CONDENSATE (ATMOSPHERIC),
UTILITY AIR, VENT GAS, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE
89 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: INSTRUMENT AIR, NITROGEN, PROCESS AIR, RELIEF LINE, STEAM CONDENSATE (ATMOSPHERIC),
UTILITY AIR, VENT GAS, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE
90 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: INSTRUMENT AIR, NITROGEN, PROCESS AIR, RELIEF LINE, STEAM CONDENSATE (ATMOSPHERIC),
UTILITY AIR, VENT GAS, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE
91 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: INSTRUMENT AIR, NITROGEN, PROCESS AIR, RELIEF LINE, STEAM CONDENSATE (ATMOSPHERIC),
UTILITY AIR, VENT GAS, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE
92 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: INSTRUMENT AIR, NITROGEN, PROCESS AIR, RELIEF LINE, STEAM CONDENSATE (ATMOSPHERIC),
UTILITY AIR, VENT GAS, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 24. For NPS 26 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
8: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
9: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the
valve at valve vendor shop.
10: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
11: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
12: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
13: Material for weld neck flanges upto NPS 24 is ASTM A105N and NPS 26 and above is ASTM A350 LF2 CL.2 as per SAES-L-109, Table-2.
14: DELETED
15: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
16: Sleved Plug Valves shall be shall be used up to design temperature 428 deg F(220 deg C).
17: Sweepolet specified in branch table shall be used wherever required as per AIV / FIV recommendation.
93 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: INSTRUMENT AIR, NITROGEN, PROCESS AIR, RELIEF LINE, STEAM CONDENSATE (ATMOSPHERIC),
UTILITY AIR, VENT GAS, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T4 T4 T1 T1 T
3 T4 T4 T4 T1 T1 T
4 T4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
14 T4 T4 T4 T4 T3 T3 T3 T3 T3 T1 T1 T
16 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T4 T4, T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
TP
24 T4 T4, T4, T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T
TP TP
28 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T1 T
30 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR T1 T1 T1 T1 T1 T
36 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR T1 T1 T1 T1 T
40 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T1 T
42 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T1 T1 T
48 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T
ABBREVIATIONS:
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
94 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: OILY WATER, OIL & OIL PRODUCTS, PRESSURISED SEWER, PROCESS WATER, RELIEF LINE, SULFUR-
MOLTEN (CONTRO-TRACED), SLOP OIL (INCLUDING OILY SLUDGE), VENT GAS, WATER, FLUSHING OIL,
NITROGEN, SOUR WATER, SULFUR DRAIN, SALT WATER, WASTE WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
SERVICE LIMITS
Size Range 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 26-60 26-60 26-60
FV up to
Pressure (Psig) 285 260 230 285 202.4 200 51 230
16"
Sch/WT XXS XXS Sch160 Sch160 Sch160 XS XS STD STD STD STD STD
Size 16 18 20 24 26 28 30 32 34 36 38 40
Sch/WT STD STD STD STD 8.74mm STD STD STD STD STD 10.31mm 10.31mm
Size 42 44 46 48 52 56 60
Elbow 45 deg 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGF000026C
95 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: OILY WATER, OIL & OIL PRODUCTS, PRESSURISED SEWER, PROCESS WATER, RELIEF LINE, SULFUR-
MOLTEN (CONTRO-TRACED), SLOP OIL (INCLUDING OILY SLUDGE), VENT GAS, WATER, FLUSHING OIL,
NITROGEN, SOUR WATER, SULFUR DRAIN, SALT WATER, WASTE WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Elbow 90 deg 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGN000070C
Tee equal 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N TEGE000013C
Tee reducing 3/4 - 1.1/2 CL 9000 SW ASME B16.11 ASTM A105N TEGR000020C
Tee reducing 1.1/2 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N TEGR000017C
96 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: OILY WATER, OIL & OIL PRODUCTS, PRESSURISED SEWER, PROCESS WATER, RELIEF LINE, SULFUR-
MOLTEN (CONTRO-TRACED), SLOP OIL (INCLUDING OILY SLUDGE), VENT GAS, WATER, FLUSHING OIL,
NITROGEN, SOUR WATER, SULFUR DRAIN, SALT WATER, WASTE WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Coupling reducing 3/4 - 1.1/2 CL 9000 SW ASME B16.11 ASTM A105N CPLR000023C
Coupling reducing 1.1/2 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N CPLR000022C
97 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: OILY WATER, OIL & OIL PRODUCTS, PRESSURISED SEWER, PROCESS WATER, RELIEF LINE, SULFUR-
MOLTEN (CONTRO-TRACED), SLOP OIL (INCLUDING OILY SLUDGE), VENT GAS, WATER, FLUSHING OIL,
NITROGEN, SOUR WATER, SULFUR DRAIN, SALT WATER, WASTE WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Nipoflange 2 - 60 * 1/2 - 2 CL 150 RF mfg std ASTM A105N 150mm long OLTF000288C 2
Nipoflange 2 - 60 * 1/2 - 2 CL 150 RF mfg std ASTM A105N 200mm long OLTF000286C 2
Nipoflange 2 - 60 * 1/2 - 2 CL 300 RF mfg std ASTM A105N 150mm long OLTF000294C 2
Nipoflange 2 - 60 * 1/2 - 2 CL 300 RF mfg std ASTM A105N 200mm long OLTF000292C 2
98 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: OILY WATER, OIL & OIL PRODUCTS, PRESSURISED SEWER, PROCESS WATER, RELIEF LINE, SULFUR-
MOLTEN (CONTRO-TRACED), SLOP OIL (INCLUDING OILY SLUDGE), VENT GAS, WATER, FLUSHING OIL,
NITROGEN, SOUR WATER, SULFUR DRAIN, SALT WATER, WASTE WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Flange SW 1/2 - 1.1/2 CL 150 SW RF ASME B16.5 ASTM A105N FLGS000001C 2,13
Flange SW 1/2 - 1.1/2 CL 300 SW RF ASME B16.5 ASTM A105N FLGS000002C 2,6,13
Flange reducing
4 - 18 CL 150 WN RF ASME B16.5 ASTM A105N FLRW000010C 2,13
WN
Spectacle Blank 1/2 - 1.1/2 CL 150 FF ASME B16.48 ASTM A516 GR 70 LBKB000352C 2
99 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: OILY WATER, OIL & OIL PRODUCTS, PRESSURISED SEWER, PROCESS WATER, RELIEF LINE, SULFUR-
MOLTEN (CONTRO-TRACED), SLOP OIL (INCLUDING OILY SLUDGE), VENT GAS, WATER, FLUSHING OIL,
NITROGEN, SOUR WATER, SULFUR DRAIN, SALT WATER, WASTE WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
100 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: OILY WATER, OIL & OIL PRODUCTS, PRESSURISED SEWER, PROCESS WATER, RELIEF LINE, SULFUR-
MOLTEN (CONTRO-TRACED), SLOP OIL (INCLUDING OILY SLUDGE), VENT GAS, WATER, FLUSHING OIL,
NITROGEN, SOUR WATER, SULFUR DRAIN, SALT WATER, WASTE WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
101 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: OILY WATER, OIL & OIL PRODUCTS, PRESSURISED SEWER, PROCESS WATER, RELIEF LINE, SULFUR-
MOLTEN (CONTRO-TRACED), SLOP OIL (INCLUDING OILY SLUDGE), VENT GAS, WATER, FLUSHING OIL,
NITROGEN, SOUR WATER, SULFUR DRAIN, SALT WATER, WASTE WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
102 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: OILY WATER, OIL & OIL PRODUCTS, PRESSURISED SEWER, PROCESS WATER, RELIEF LINE, SULFUR-
MOLTEN (CONTRO-TRACED), SLOP OIL (INCLUDING OILY SLUDGE), VENT GAS, WATER, FLUSHING OIL,
NITROGEN, SOUR WATER, SULFUR DRAIN, SALT WATER, WASTE WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
103 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: OILY WATER, OIL & OIL PRODUCTS, PRESSURISED SEWER, PROCESS WATER, RELIEF LINE, SULFUR-
MOLTEN (CONTRO-TRACED), SLOP OIL (INCLUDING OILY SLUDGE), VENT GAS, WATER, FLUSHING OIL,
NITROGEN, SOUR WATER, SULFUR DRAIN, SALT WATER, WASTE WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
104 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: OILY WATER, OIL & OIL PRODUCTS, PRESSURISED SEWER, PROCESS WATER, RELIEF LINE, SULFUR-
MOLTEN (CONTRO-TRACED), SLOP OIL (INCLUDING OILY SLUDGE), VENT GAS, WATER, FLUSHING OIL,
NITROGEN, SOUR WATER, SULFUR DRAIN, SALT WATER, WASTE WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 24. For NPS 26 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
8: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
9: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the
valve at valve vendor shop.
10: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
11: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
12: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
13: Material for weld neck flanges upto NPS 24 is ASTM A105N and NPS 26 and above is ASTM A350 LF2 CL.2 as per SAES-L-109, Table-2.
14: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
15: Lubricated Plug Valves shall be used for design temperature range 429 deg F (221 deg C) to 608 deg F (320 deg C).
105 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: OILY WATER, OIL & OIL PRODUCTS, PRESSURISED SEWER, PROCESS WATER, RELIEF LINE, SULFUR-
MOLTEN (CONTRO-TRACED), SLOP OIL (INCLUDING OILY SLUDGE), VENT GAS, WATER, FLUSHING OIL,
NITROGEN, SOUR WATER, SULFUR DRAIN, SALT WATER, WASTE WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T4 T4 T1 T1 T
3 T4 T4 T4 T1 T1 T
4 T4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T4 T3 T1, T1 T
T1
8 T4 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
14 T4 T4 T4 T4 T3 T3 T3 T3 T3 T1 T1 T
16 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
24 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T
ABBREVIATIONS:
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
106 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Size Range 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 26-60 26-60
FV upto
12", HV
Pressure (Psig) 285 260 230 285 110.6 170 HV 51
above
14"
Sch/WT XXS XXS Sch160 Sch160 Sch160 XS XS STD STD STD STD STD
Size 16 18 20 22 24 26 28 30 32 34 36 38
Sch/WT STD STD STD STD STD STD STD 10.15mm 10.31mm 11.13mm 11.13mm 11.91mm
Size 40 42 44 46 48 52 56 60 60
Elbow 45 deg 3/4 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGF000026C
107 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Elbow 90 deg 3/4 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGN000070C
Tee equal 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N TEGE000013C
108 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Tee reducing 3/4 - 1.1/2 CL 9000 SW ASME B16.11 ASTM A105N TEGR000020C
Tee reducing 1.1/2 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N TEGR000017C
109 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Coupling reducing 1.1/2 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N CPLR000022C
110 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Nipoflange 2 - 60 * 3/4 - 2 CL 150 RF mfg std ASTM A105N 150mm long OLTF000288C 2
Nipoflange 2 - 60 * 3/4 - 2 CL 150 RF mfg std ASTM A105N 200mm long OLTF000286C 2
Nipoflange 2 - 60 * 3/4 - 2 CL 300 RF mfg std ASTM A105N 150mm long OLTF000294C 2
Nipoflange 2 - 60 * 3/4 - 2 CL 300 RF mfg std ASTM A105N 200mm long OLTF000292C 2
111 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Flange reducing
4-6 CL 150 WN RF ASME B16.5 ASTM A105N FLRW000010C 2
WN
112 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Spectacle Blank 3/4 - 1.1/2 CL 150 FF ASME B16.48 ASTM A516 GR 70 LBKB000352C 2
113 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
114 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
115 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
116 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
117 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 24. For NPS 26 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
8: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
9: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the
valve at valve vendor shop.
10: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
11: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
12: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
13: Material for weld neck flanges upto NPS 24 is ASTM A105N and NPS 26 and above is ASTM A350 LF2 CL.2 as per SAES-L-109, Table-2.
14: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
118 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
15: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
16: Alternate wall thickness (28.58mm) for NPS 60 is considered as per FEA stress calculation requirement.
119 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T4 T4 T1 T1 T
3 T4 T4 T4 T1 T1 T
4 T4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
14 T4 T4 T4 T4 T3 T3 T3 T3 T3 T1 T1 T
16 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
24 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T
30 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR T1 T1 T1 T1 T
36 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR T1 T1 T1 T
40 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T
42 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T1 T
48 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T
56 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T
60 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T1 T
ABBREVIATIONS:
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
120 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
121 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
122 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
123 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
124 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
125 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
6: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
7: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
8: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
10: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
11: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
12: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
126 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T3 T3 T1 T1 T
3 T3 T3 T3 T1 T1 T
4 T3 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T3 T1 T1 T
8 T3 T3 T3 T3 T3 T3 T1 T1 T
10 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
12 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
127 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BLOWDOWN, STEAM, STEAM CONDENSATE (ATMOSPHERIC), VENT GAS, 600
PSIG H.P. CONDENSATE, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE, L.L.P.
CONDENSATE, NITROGEN, BOILER FEED WATER.
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
SERVICE LIMITS
Size Range 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 26-30 26-30 26-30
Sch/WT XXS XXS Sch160 Sch160 Sch160 XS XS STD STD STD STD STD
Size 16 18 20 24 26 28 30
Elbow 45 deg 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGF000026C
128 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BLOWDOWN, STEAM, STEAM CONDENSATE (ATMOSPHERIC), VENT GAS, 600
PSIG H.P. CONDENSATE, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE, L.L.P.
CONDENSATE, NITROGEN, BOILER FEED WATER.
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Elbow 90 deg 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGN000070C
Tee equal 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N TEGE000013C
Tee reducing 3/4 - 1.1/2 CL 9000 SW ASME B16.11 ASTM A105N TEGR000020C
Tee reducing 1.1/2 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N TEGR000017C
129 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BLOWDOWN, STEAM, STEAM CONDENSATE (ATMOSPHERIC), VENT GAS, 600
PSIG H.P. CONDENSATE, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE, L.L.P.
CONDENSATE, NITROGEN, BOILER FEED WATER.
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
130 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BLOWDOWN, STEAM, STEAM CONDENSATE (ATMOSPHERIC), VENT GAS, 600
PSIG H.P. CONDENSATE, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE, L.L.P.
CONDENSATE, NITROGEN, BOILER FEED WATER.
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Coupling reducing 3/4 - 1.1/2 CL 9000 SW ASME B16.11 ASTM A105N CPLR000023C
Coupling reducing 1.1/2 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N CPLR000022C
Nipoflange 2 - 30 * 1/2 - 2 CL 150 RF mfg std ASTM A105N 150mm long OLTF000288C 2
Nipoflange 2 - 30 * 1/2 - 2 CL 150 RF mfg std ASTM A105N 200mm long OLTF000286C 2
Nipoflange 2 - 30 * 1/2 - 2 CL 300 RF mfg std ASTM A105N 150mm long OLTF000294C 2
Nipoflange 2 - 30 * 3/4 - 2 CL 300 RF mfg std ASTM A105N 200mm long OLTF000292C 2
131 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BLOWDOWN, STEAM, STEAM CONDENSATE (ATMOSPHERIC), VENT GAS, 600
PSIG H.P. CONDENSATE, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE, L.L.P.
CONDENSATE, NITROGEN, BOILER FEED WATER.
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
132 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BLOWDOWN, STEAM, STEAM CONDENSATE (ATMOSPHERIC), VENT GAS, 600
PSIG H.P. CONDENSATE, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE, L.L.P.
CONDENSATE, NITROGEN, BOILER FEED WATER.
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Spectacle Blank 1/2 - 1.1/2 CL 150 FF ASME B16.48 ASTM A516 GR 70 LBKB000352C 2
Spectacle Blank 1/2 - 1.1/2 CL 300 FF ASME B16.48 ASTM A516 GR 70 LBKB000353C
133 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BLOWDOWN, STEAM, STEAM CONDENSATE (ATMOSPHERIC), VENT GAS, 600
PSIG H.P. CONDENSATE, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE, L.L.P.
CONDENSATE, NITROGEN, BOILER FEED WATER.
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
134 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BLOWDOWN, STEAM, STEAM CONDENSATE (ATMOSPHERIC), VENT GAS, 600
PSIG H.P. CONDENSATE, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE, L.L.P.
CONDENSATE, NITROGEN, BOILER FEED WATER.
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
135 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BLOWDOWN, STEAM, STEAM CONDENSATE (ATMOSPHERIC), VENT GAS, 600
PSIG H.P. CONDENSATE, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE, L.L.P.
CONDENSATE, NITROGEN, BOILER FEED WATER.
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
136 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BLOWDOWN, STEAM, STEAM CONDENSATE (ATMOSPHERIC), VENT GAS, 600
PSIG H.P. CONDENSATE, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE, L.L.P.
CONDENSATE, NITROGEN, BOILER FEED WATER.
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
137 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BLOWDOWN, STEAM, STEAM CONDENSATE (ATMOSPHERIC), VENT GAS, 600
PSIG H.P. CONDENSATE, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE, L.L.P.
CONDENSATE, NITROGEN, BOILER FEED WATER.
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
138 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BLOWDOWN, STEAM, STEAM CONDENSATE (ATMOSPHERIC), VENT GAS, 600
PSIG H.P. CONDENSATE, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE, L.L.P.
CONDENSATE, NITROGEN, BOILER FEED WATER.
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 24. For NPS 26 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
8: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
9: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the
valve at valve vendor shop.
10: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
11: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
12: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
13: Material for weld neck flanges upto NPS 24 is ASTM A105N and NPS 26 and above is ASTM A350 LF2 CL.2 as per SAES-L-109, Table-2.
14: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
139 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BLOWDOWN, STEAM, STEAM CONDENSATE (ATMOSPHERIC), VENT GAS, 600 PSIG
H.P. CONDENSATE, 60 PSIG LLP STEAM, 15 PSIG LLP STEAM, I. P. CONDENSATE, L.L.P. CONDENSATE,
NITROGEN, BOILER FEED WATER.
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T4 T4 T1 T1 T
3 T4 T4 T4 T1 T1 T
4 T4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
14 T4 T4 T4 T4 T3 T3 T3 T3 T3 T1 T1 T
16 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
24 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T
30 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR T1 T1 T1 T1 T
ABBREVIATIONS:
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
140 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHILLED WATER, COOLING WATER RETURN, COOLING WATER SUPPLY, RAW WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim bronze/ bronze PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
SERVICE LIMITS
Sch/WT XXS XXS Sch160 Sch160 Sch160 XS XS STD STD STD STD STD
Size 16 18 20 24 26 28 30 32 34 36 38 40
Sch/WT STD STD STD STD 8.74mm STD STD STD 10.31mm 10.31mm 10.31mm 11.13mm
Size 42 44 46 48
Elbow 45 deg 3/4 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGF000026C
141 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHILLED WATER, COOLING WATER RETURN, COOLING WATER SUPPLY, RAW WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim bronze/ bronze PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Elbow 90 deg 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGN000070C
Tee equal 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N TEGE000013C
Tee reducing 3/4 - 1.1/2 CL 9000 SW ASME B16.11 ASTM A105N TEGR000020C
Tee reducing 1.1/2 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N TEGR000017C
142 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHILLED WATER, COOLING WATER RETURN, COOLING WATER SUPPLY, RAW WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim bronze/ bronze PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Pipe Nipple
143 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHILLED WATER, COOLING WATER RETURN, COOLING WATER SUPPLY, RAW WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim bronze/ bronze PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Pipe Nipple
Coupling reducing 1.1/2 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N CPLR000022C
Nipoflange 2 - 48 * 1/2 - 2 CL 150 RF mfg std ASTM A105N 150mm long OLTF000288C 2
Nipoflange 2 - 48 * 1/2 - 2 CL 150 RF mfg std ASTM A105N 200mm long OLTF000286C 2
Nipoflange 2 - 48 * 1/2 - 2 CL 300 RF mfg std ASTM A105N 200mm long OLTF000292C 2, 6
Nipoflange 2 - 48 * 1/2 - 2 CL 300 RF mfg std ASTM A105N 150mm long OLTF000294C 2, 6
144 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHILLED WATER, COOLING WATER RETURN, COOLING WATER SUPPLY, RAW WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim bronze/ bronze PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
145 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHILLED WATER, COOLING WATER RETURN, COOLING WATER SUPPLY, RAW WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim bronze/ bronze PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Spectacle Blank 3/4 - 1.1/2 CL 150 FF ASME B16.48 ASTM A516 GR 70 LBKB000352C
146 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHILLED WATER, COOLING WATER RETURN, COOLING WATER SUPPLY, RAW WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim bronze/ bronze PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
147 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHILLED WATER, COOLING WATER RETURN, COOLING WATER SUPPLY, RAW WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim bronze/ bronze PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
148 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHILLED WATER, COOLING WATER RETURN, COOLING WATER SUPPLY, RAW WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim bronze/ bronze PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
149 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHILLED WATER, COOLING WATER RETURN, COOLING WATER SUPPLY, RAW WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim bronze/ bronze PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 24. For NPS 26 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
8: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
9: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the valve
at valve vendor shop.
10: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
11: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
12: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
13: Material for weld neck flanges upto NPS 24 is ASTM A105N and NPS 26 and above is ASTM A350 LF2 CL.2 as per SAES-L-109, Table-2.
14: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
150 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CS2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHILLED WATER, COOLING WATER RETURN, COOLING WATER SUPPLY, RAW WATER
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim bronze/ bronze PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T4 T4 T1 T1 T
3 T4 T4 T4 T1 T1 T
4 T4 T4 T4 T1 T1 T1 T
6 T4 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
14 T4 T4 T4 T4 T3 T3 T3 T3 T3 T1 T1 T
16 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
24 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T
26 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T1 T
28 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T1 T1 T
30 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR T1 T1 T1 T1 T1 T1 T
32 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR T1 T1 T1 T1 T1 T1 T1 T
34 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR T1 T1 T1 T1 T1 T1 T1 T1 T
36 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR T1 T1 T1 T1 T1 T1 T1 T
38 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T
40 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T
42 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T1 T
44 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
46 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
48 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
ABBREVIATIONS:
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
151 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Temperature
Core 32 100 200 300 400 450 -
(ºF)
Pressure
285 285 260 230 200 185 FV
(Psig)
Size Range 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24
Temperature
Jacket 32 100 200 300 395 -
(ºF)
Pressure
285 285 260 230 201.5 FV
(Psig)
Size 1 1.1/2 2 3 4 6 8 10
152 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Elbow 90 deg 1/2 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N ELGN000069C
153 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Coupling reducing 3/4 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N CPLR000022C
154 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
155 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
156 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: DELETED
4: DELETED
5: DELETED
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Gate Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for process
drain/vent.
8: DELETED
9: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
10: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
11: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
12: Sleved Plug Valves shall be shall be used up to design temperature 428 deg F(220 deg C).
157 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1 T
RUN PIPE
1.1/2 T1 T
10 T4
ABBREVIATIONS:
158 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Size Range 1-24 1-24 1-24 1-24 1-24 1-24 26-30 26-30
Temperature
Core 32 100 200 300 405 - 405 -
(ºF)
Pressure
285 285 260 230 198.5 HV 155 HV
(Psig)
Size Range 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 26-36 26-36
Temperature
Jacket 32 100 200 300 395 - 395 -
(ºF)
Pressure
285 285 260 230 201.5 FV 95 FV
(Psig)
Size 1 1.1/2 2 3 4 6 8 10
Sch/WT 14.27 mm 14.27 mm 15.88 mm 17.48 mm 17.48 mm 20.62 mm 20.62 mm 20.62 mm 22.23mm
Sch/WT STD STD STD STD STD STD STD 8.74mm STD STD 11.13mm
159 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Elbow 45 deg 1/2 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N ELGF000024C
Elbow 90 deg 1/2 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N ELGN000069C
160 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
161 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
162 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
163 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 24. For NPS 26 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
4: For Core piping, all welds for all wall thicknesses including those made in manufacture and repair shall require PWHT.
5: Material for weld neck flanges upto NPS 24 is ASTM A105N and NPS 26 and above is ASTM A350 LF2 CL.2 as per SAES-L-109, Table-2.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Gate Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for process
drain/vent.
8: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
9: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
10: Steam Jacket to be designed at least one size larger than the inner pipe.
11: Jacket pipe is designed for low pressure steam (maximum 150 psig) with1.6 mm corrosion allowance
12: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
13: For Core piping, all material shall meet the requirements of NACE MR0175/ISO 15156.
14: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
164 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
165 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
ABBREVIATIONS:
166 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Size Range 1-24 1-24 1-24 1-24 1-24 1-24 1-24 26-30 26-30
Temperature
Core 32 100 200 400 600 644 - 644 -
(ºF)
Pressure
285 285 260 200 140 126.8 HV 51 HV
(Psig)
Size Range 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 26-36 26-36
Temperature
Jacket 32 100 200 300 395 - 395 -
(ºF)
Pressure
285 285 260 230 201.5 FV 95 FV
(Psig)
Size 1 1.1/2 2 3 4 6 8 10
Sch/WT Sch 60 Sch 60 15.88 mm 17.48 mm 19.05 mm 20.62 mm 20.62 mm 20.62 mm 22.23mm
Sch/WT STD STD STD STD STD STD 8.74mm STD STD 11.13mm
167 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
168 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 24. For NPS 26 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
4: For Core piping, all welds for all wall thicknesses including those made in manufacture and repair shall require PWHT.
5: Material for weld neck flanges upto NPS 24 is ASTM A105N and NPS 26 and above is ASTM A350 LF2 CL.2 as per SAES-L-109, Table-2.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Gate Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for process
drain/vent.
8: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
9: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
10: Steam Jacket to be designed at least one size larger than the inner pipe.
11: This pipe class is applicable for Category M service and shall comply to ASME B31.3, Chapter VIII requirements.
12: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Helium.
169 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
13: Jacket pipe is designed for low pressure steam (maximum 150 psig) with1.6 mm corrosion allowance
14: For Core piping, all materials shall meet the requirements of NACE MR0175/ISO 15156.
15: All soft seat valves shall be fire safe design as per API 607 / API 6FA / ISO 10497.
170 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
ABBREVIATIONS:
171 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Temperature
Core 32 100 200 400 650 698 -
(ºF)
Pressure
285 285 260 200 125 110.6 HV
(Psig)
Size Range 0.5-36 0.5-36 0.5-36 0.5-36 0.5-36 0.5-36
Temperature
Jacket 32 100 200 300 395 -
(ºF)
Pressure
285 285 260 230 201.5 FV
(Psig)
Size 1 1.1/2 2 3 4 6 8 10
Sch/WT STD STD STD STD STD STD 8.74mm STD STD 11.13mm
Elbow 90 deg 3/4 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N ELGN000069C
172 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Reducer Concentric
Reducer eccentric
173 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Nipoflange 6 - 6 * 1.1/2 - 1.1/2 CL 150 RF mfg std ASTM A105N 200mm long OLTF000286C 2
Nipoflange 6 - 6 * 1.1/2 - 1.1/2 CL 300 RF mfg std ASTM A105N 200mm long OLTF000292C 2
174 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
175 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
176 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
ELBOW_WROUGH
T_SPLIT
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
4: Gate Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for process
drain/vent.
5: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
6: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
7: Steam Jacket to be designed at least one size larger than the inner pipe.
8: Jacket pipe is designed for low pressure steam (maximum 150 psig) with1.6 mm corrosion allowance
9: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
177 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
10: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
11: Sleved Plug Valves shall be shall be used up to design temperature 428 deg F(220 deg C). Lubricated Plug Valves shall be used for design
temperature range 429 deg F (221 deg C) to 608 deg F (320 deg C).
12: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
178 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CX4P20
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1 T
RUN PIPE
1.1/2 T
ABBREVIATIONS:
179 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, SLOP OIL (INCLUDING OILY SLUDGE), 60 PSIG LLP STEAM, ACID GAS, LOW PRESSURE
FLARE, PRESSURISED SEWER, PROCESS WATER, MONO ETHYLENE GLYCOL
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
SERVICE LIMITS
Size Range 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 26-48 26-48 26-48 26-48 26-48
Temperature (ºF) - 100 200 32 400 600 644 - 300 350 405 644
FV upto
6", HV
HV, FE
above
Pressure (Psig) 285 260 285 200 140 126.8 upto 30" 220 51 155 51
8", FV
(Alt)
above 8"
(Alt)
Pressure (Psig) HV 51
Sch/WT XXS XXS Sch160 Sch160 Sch160 XS XS STD STD STD STD
Size 14 16 18 20 24 26 28 30 30 32 34 36
Sch/WT STD STD STD STD STD STD 10.15mm 10.15mm 11.13mm 11.13mm 11.13mm 11.91mm
Size 38 40 42 44 46 48 52 56 60
180 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, SLOP OIL (INCLUDING OILY SLUDGE), 60 PSIG LLP STEAM, ACID GAS, LOW PRESSURE
FLARE, PRESSURISED SEWER, PROCESS WATER, MONO ETHYLENE GLYCOL
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
181 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, SLOP OIL (INCLUDING OILY SLUDGE), 60 PSIG LLP STEAM, ACID GAS, LOW PRESSURE
FLARE, PRESSURISED SEWER, PROCESS WATER, MONO ETHYLENE GLYCOL
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
182 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, SLOP OIL (INCLUDING OILY SLUDGE), 60 PSIG LLP STEAM, ACID GAS, LOW PRESSURE
FLARE, PRESSURISED SEWER, PROCESS WATER, MONO ETHYLENE GLYCOL
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
183 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, SLOP OIL (INCLUDING OILY SLUDGE), 60 PSIG LLP STEAM, ACID GAS, LOW PRESSURE
FLARE, PRESSURISED SEWER, PROCESS WATER, MONO ETHYLENE GLYCOL
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
184 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, SLOP OIL (INCLUDING OILY SLUDGE), 60 PSIG LLP STEAM, ACID GAS, LOW PRESSURE
FLARE, PRESSURISED SEWER, PROCESS WATER, MONO ETHYLENE GLYCOL
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
Spectacle Blank
185 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, SLOP OIL (INCLUDING OILY SLUDGE), 60 PSIG LLP STEAM, ACID GAS, LOW PRESSURE
FLARE, PRESSURISED SEWER, PROCESS WATER, MONO ETHYLENE GLYCOL
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
186 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, SLOP OIL (INCLUDING OILY SLUDGE), 60 PSIG LLP STEAM, ACID GAS, LOW PRESSURE
FLARE, PRESSURISED SEWER, PROCESS WATER, MONO ETHYLENE GLYCOL
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
187 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, SLOP OIL (INCLUDING OILY SLUDGE), 60 PSIG LLP STEAM, ACID GAS, LOW PRESSURE
FLARE, PRESSURISED SEWER, PROCESS WATER, MONO ETHYLENE GLYCOL
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
188 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, SLOP OIL (INCLUDING OILY SLUDGE), 60 PSIG LLP STEAM, ACID GAS, LOW PRESSURE
FLARE, PRESSURISED SEWER, PROCESS WATER, MONO ETHYLENE GLYCOL
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
189 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, SLOP OIL (INCLUDING OILY SLUDGE), 60 PSIG LLP STEAM, ACID GAS, LOW PRESSURE
FLARE, PRESSURISED SEWER, PROCESS WATER, MONO ETHYLENE GLYCOL
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
190 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, SLOP OIL (INCLUDING OILY SLUDGE), 60 PSIG LLP STEAM, ACID GAS, LOW PRESSURE
FLARE, PRESSURISED SEWER, PROCESS WATER, MONO ETHYLENE GLYCOL
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 24. For NPS 26 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in
P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
191 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, SLOP OIL (INCLUDING OILY SLUDGE), 60 PSIG LLP STEAM, ACID GAS, LOW PRESSURE
FLARE, PRESSURISED SEWER, PROCESS WATER, MONO ETHYLENE GLYCOL
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
8: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
9: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
10: Material for weld neck flanges upto NPS 24 is ASTM A105N and NPS 26 and above is ASTM A350 LF2 CL.2 as per SAES-L-109, Table-2.
11: All material shall meet the requirements of NACE MR0175/ISO 15156.
12: All welds for all wall thicknesses including those made in manufacture and repair shall require PWHT.
13: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
14: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
192 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, SLOP OIL (INCLUDING OILY SLUDGE), 60 PSIG LLP STEAM, ACID GAS, LOW PRESSURE
FLARE, PRESSURISED SEWER, PROCESS WATER, MONO ETHYLENE GLYCOL
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
1/2 T
RUN PIPE
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T3 T3 T1, T1 T
3 T3 T3 T3 T1 T1 T
4 T3 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T3 T1 T1 T
8 T3 T3 T3 T3 T3 T3 T1 T1 T
10 T3 T3 T3 T3 T3, T3 T3 T1 T1 T
12 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
14 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
16 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
24 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T
30 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR T1 T1 T1 T1 T
36 T
40 T
42 T
48 T3 T3 T3 T1 T
1/2 TL
RUN PIPE SIZE
3/4 TLR TL
1 TLR TLR TL
1.1/2 TLR TLR TLR TL
2 T8 T8 TLR, TLR TL
3 T8 T8 T8 TLR TLR TL
4 T8 T8 T8 T8 TLR TLR TL
6 T8 T8 T8 T8 T8 TLR TLR TL
8 T8 T8 T8 T8 T8 T8 TLR TLR TL
10 T8 T8 T8 T8 T8, T8 T8 TLR TLR TL
12 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
14 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
16 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
18 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
20 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TLR TL
24 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TLR TLR TL
30 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TLR TLR TLR TLR TL
36 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TLR TLR TLR TL
40 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TLR TLR TLR TL
42 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TL
48 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TL
193 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, SLOP OIL (INCLUDING OILY SLUDGE), 60 PSIG LLP STEAM, ACID GAS, LOW PRESSURE
FLARE, PRESSURISED SEWER, PROCESS WATER, MONO ETHYLENE GLYCOL
Pipe Material: CS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: YES
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, HIC
Resistance, Toxic
ABBREVIATIONS:
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
TL: Equal Tee - 45 Deg
TLR: Reducing Tee - 45 Deg
TR1: Stub in Connection with Full encirclement sleeve - 45 Deg
T8: Latrolet
194 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Size Range 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 26-60 26-60 26-60
Sch/WT XXS XXS Sch160 Sch160 Sch160 XS XS STD STD STD STD STD
Size 16 18 20 24 26 28 30 32 34 36 38 40
Sch/WT STD STD STD STD STD STD 10.15mm 10.31mm 11.13mm 11.13mm 11.91mm 11.91mm
Size 42 44 46 48 52 56 60
195 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
196 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
197 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
198 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
199 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
200 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
201 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
202 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
203 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 24. For NPS 26 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
9: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
10: Material for weld neck flanges upto NPS 24 is ASTM A105N and NPS 26 and above is ASTM A350 LF2 CL.2 as per SAES-L-109, Table-2.
11: All material shall meet the requirements of NACE MR0175/ISO 15156.
12: All welds for all wall thicknesses including those made in manufacture and repair shall require PWHT.
13: This pipe class is applicable for Category M service and shall comply to ASME B31.3, Chapter VIII requirements.
14: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Helium.
204 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
15: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
205 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T3 T3 T1 T1 T
3 T3 T3 T3 T1 T1 T
4 T3 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T3 T1 T1 T
8 T3 T3 T3 T3 T3 T3 T1 T1 T
10 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
12 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
14 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
16 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
24 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T
30 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR T1 T1 T1 T1 T
36 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR T1 T1 T1 T
40 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T
42 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T1 T
48 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T
52 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
56 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
60 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
3/4 TLR TL
1 TLR TLR TL
1.1/2 TLR TLR TLR TL
2 T8 T8 TLR TLR TL
3 T8 T8 T8 TLR TLR TL
4 T8 T8 T8 T8 TLR TLR TL
6 T8 T8 T8 T8 T8 TLR TLR TL
8 T8 T8 T8 T8 T8 T8 TLR TLR TL
10 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
12 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
14 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
16 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
18 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
20 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TLR TL
24 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TLR TLR TL
30 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TLR TLR TLR TLR TL
36 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TLR TLR TLR TL
40 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TLR TLR TLR TL
42 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TL
48 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TL
52 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TL
56 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TL
60 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TLR TL
ABBREVIATIONS:
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
TL: Equal Tee - 45 Deg
TLR: Reducing Tee - 45 Deg
TR1: Stub in Connection with Full encirclement sleeve - 45 Deg
T8: Latrolet
206 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Sch/WT XXS XXS Sch160 Sch160 Sch160 XS XS STD STD STD STD STD
Size 16 18
207 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
208 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
209 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
210 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
211 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
212 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 24.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
213 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
10: All welds for all wall thicknesses including those made in manufacture and repair shall require PWHT.
11: Sealing material requirement for Amine Service shall be as per Project Specification Material Requirement for CRA, CS and Low Alloy Steel
(For piping, fittings, flanges & valves), Doc.No. D44-A-RE-380920.
12: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
13: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
214 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1/2 T
RUN PIPE
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T3 T3 T1 T1 T
3 T3 T3 T3 T1 T1 T
4 T3 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T3 T1 T1 T
8 T3 T3 T3 T3 T3 T3 T1 T1 T
10 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
12 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
14 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
16 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
215 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Pressure (Psig) FV 50 50 50
Size 1 2 3 4 6 8 10 12
Sch/WT
adhesive jt
ASTM D2996 fil wnd glass fbr reinf
Pipe RTR 1 - 12 10 barg socket x spigot PIPR000030C
epoxy
(taper)
216 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
217 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
2: DELETED
218 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
2 T1 T
3 T1 T1 T
4 T1 T1 T1 T
6 T1 T1 T1 T1 T
8 T1 T1 T1 T1 T1 T
10 T1 T1 T1 T1 T1 T1 T
12 T1 T1 T1 T1 T1 T1 T1 T
ABBREVIATIONS:
219 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Pressure (Psig) FV 50 50 50
Size 1 2 3 4 6 8 10 12 14 16 18 20
Sch/WT
Size 24 26 28 30 32 34 36 38 40 42 44 46
Sch/WT
Size 48 52 54 56 60 64 66 68 72
Sch/WT
adhesive jt
ASTM D3262 fil wnd glass fbr reinf
Pipe RTR 1 - 24 10 barg socket x spigot PIPR000037C
epoxy
(taper)
Elbow 22.5 deg adhesive jt ASTM D5685 fil wnd/moulded glass fbr
1 - 24 10 barg ELRT000008C
RTR socket (taper) reinf epoxy
220 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
221 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
222 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: DELETED
2: DELETED
223 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
2 T1 T
3 T1 T1 T
4 T1 T1 T1 T
6 T1 T1 T1 T1 T
8 T1 T1 T1 T1 T1 T
10 T1 T1 T1 T1 T1 T1 T
12 T1 T1 T1 T1 T1 T1 T1 T
14 T1 T1 T1 T1 T1 T1 T1 T1 T
16 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
18 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
20 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
24 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
30 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
36 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
40 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
42 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
48 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
56 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
ABBREVIATIONS:
224 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Size 1 2 3 4 6 8 10 12 14 16
Sch/WT
adhesive jt
ASTM D2996 fil wnd glass fbr reinf
Pipe RTR 1 - 16 16 barg socket x spigot PIPR000031C
epoxy UL/FM approved
(taper)
225 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
226 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: DELETED
2: DELETED
227 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1 T
RUN PIPE
2 T1 T
3 T1 T1 T
4 T1 T1 T1 T
6 T1 T1 T1 T1 T
8 T1 T1 T1 T1 T1 T
10 T1 T1 T1 T1 T1 T1 T
12 T1 T1 T1 T1 T1 T1 T1 T
14 T1 T1 T1 T1 T1 T1 T1 T1 T
16 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
ABBREVIATIONS:
228 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0W13
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Size 1 2 3 4 6 8 10
Sch/WT
229 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0W13
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
230 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0W13
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: DELETED
2: DELETED
231 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1FE0W13
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1 T
RUN PIPE
2 T1 T
3 T1 T1 T
4 T1 T1 T1 T
6 T1 T1 T1 T1 T
8 T1 T1 T1 T1 T1 T
10 T1 T1 T1 T1 T1 T1 T
ABBREVIATIONS:
232 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Sch/WT Sch40S Sch40S Sch40S Sch40S Sch160 XS XS STD STD STD Sch30 Sch20
Size 16 18 20
Elbow 45 deg 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 ELGF000040C
Elbow 90 deg 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 ELGN000082C
Tee equal 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 TEGE000025C
233 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Tee reducing 3/4 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 TEGR000032C
Cap 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 CAPG000044C
Pipe Nipple
Coupling reducing 3/4 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 CPLR000039C
234 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Flange SW 1/2 - 1.1/2 CL 150 SW RF ASME B16.5 ASTM A182 GR F44 FLGS000068C 2
Flange SW 1/2 - 1.1/2 CL 300 SW RF ASME B16.5 ASTM A182 GR F44 FLGS000069C 2
Flange reducing
2-2 CL 150 SW FF ASME B16.5 ASTM A182 GR F44 FLRS000005C
SW
235 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Blind Flange 1/2 - 1.1/2 CL 150 RF ASME B16.5 ASTM A182 GR F44 FLGB000294C 2
236 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
237 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.8 of ASME B16.5 upto NPS 1.5 and Table 1 of ASME B16.42 for NPS 2 and above.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
238 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
9: FBE (Fusion Bonded Epoxy) shall be applied internally to the piping after fabrication and fully tested.
10: FBE (Fusion Bonded Epoxy) shall be applied as per Project Specification for Internal Lining (D44-A-RE-380908).
11: Branch connection for size NPS 1.1/2 and below shall be made by providing NPS 2 epoxy lined branch connection with flange
(weldolet/reducing tee as per branch table + 2" FBE Lined Flange) and making the connection with 6Mo Reducing WN Flange.
12: Bronze trim shall have less than 16% zinc.
13: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
14: Gate Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for process
drain/vent.
239 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1/2 T
RUN PIPE
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 SS SS SS SS T
3 SS SS SS SS T1 T
4 SS SS SS SS T1 T1 T
6 SS SS SS SS T3 T1 T1 T
8 SS SS SS SS T3 T3 T1 T1 T
10 SS SS SS SS T3 T3 T3 T1 T1 T
12 SS SS SS SS T3 T3 T3 T3 T1 T1 T
14 SS SS SS SS T3 T3 T3 T3 T3 T1 T1 T
16 SS SS SS SS T3 T3 T3 T3 T3 T3 T1 T1 T
18 SS SS SS SS T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 SS SS SS SS T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
ABBREVIATIONS:
240 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2P07
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Sch/WT Sch40S Sch40S Sch40S Sch40S Sch160 XS XS STD STD STD Sch30
241 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2P07
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
242 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2P07
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
243 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2P07
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
244 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2P07
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.8 of ASME B16.5 upto NPS 1.5 and Table 1 of ASME B16.42 for NPS 2 and above.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
245 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2P07
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
9: FBE (Fusion Bonded Epoxy) shall be applied internally to the piping after fabrication and fully tested.
10: FBE (Fusion Bonded Epoxy) shall be applied as per Project Specification for Internal Lining (D44-A-RE-380908).
11: Branch connection for size NPS 1.1/2 and below shall be made by providing NPS 2 epoxy lined branch connection with flange
(weldolet/reducing tee as per branch table + 2" FBE Lined Flange) and making the connection with 6Mo Reducing WN Flange.
12: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
246 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2P07
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 SS SS SS SS T
3 SS SS SS SS T1 T
4 SS SS SS SS T1 T1 T
6 SS SS SS SS T3 T1 T1 T
8 SS SS SS SS T3 T3 T1 T1 T
10 SS SS SS SS T3 T3 T3 T1 T1 T
12 SS SS SS SS T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
247 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SLOP OIL (INCLUDING OILY SLUDGE), SANITARY WATER, TREATED WATER, VENT GAS, OILY WATER,
OILY WATER SEWER, UTILITY WATER, WATER, BLOWDOWN, SOUR WATER
Pipe Material: 6Mo SS/ CS+internal FBE lined Flange Rating: CL 150
Valve Trim: UNS S31254 (upto 1.1/2") / bronze (2" & PWHT: AS PER ASME B31.3
above)
Corrosion Allowance: 0mm (upto 1.1/2") / 3.2mm(2" &above) Code: ASME B31.3 - 2012
Service Type: Special Requirements:
SERVICE LIMITS
Size Range 0.5-1.5 0.5-1.5 0.5-1.5 0.5-1.5 2-14 2-14 2-14 2-14
Sch/WT Sch40S Sch40S Sch40S Sch40S Sch160 XS XS STD STD STD Sch30 Sch20
Elbow 45 deg 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 ELGF000040C
Elbow 90 deg 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 ELGN000082C
Tee equal 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 TEGE000025C
248 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SLOP OIL (INCLUDING OILY SLUDGE), SANITARY WATER, TREATED WATER, VENT GAS, OILY WATER,
OILY WATER SEWER, UTILITY WATER, WATER, BLOWDOWN, SOUR WATER
Pipe Material: 6Mo SS/ CS+internal FBE lined Flange Rating: CL 150
Valve Trim: UNS S31254 (upto 1.1/2") / bronze (2" & PWHT: AS PER ASME B31.3
above)
Corrosion Allowance: 0mm (upto 1.1/2") / 3.2mm(2" &above) Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Tee reducing 3/4 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 TEGR000032C
Cap 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 CAPG000044C
Pipe Nipple
Coupling reducing 3/4 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 CPLR000039C
249 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SLOP OIL (INCLUDING OILY SLUDGE), SANITARY WATER, TREATED WATER, VENT GAS, OILY WATER,
OILY WATER SEWER, UTILITY WATER, WATER, BLOWDOWN, SOUR WATER
Pipe Material: 6Mo SS/ CS+internal FBE lined Flange Rating: CL 150
Valve Trim: UNS S31254 (upto 1.1/2") / bronze (2" & PWHT: AS PER ASME B31.3
above)
Corrosion Allowance: 0mm (upto 1.1/2") / 3.2mm(2" &above) Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Flange SW 1/2 - 1.1/2 CL 150 SW RF ASME B16.5 ASTM A182 GR F44 FLGS000068C 2
Flange SW 1/2 - 1.1/2 CL 300 SW RF ASME B16.5 ASTM A182 GR F44 FLGS000069C 2
Flange reducing
2-2 CL 150 SW FF ASME B16.5 ASTM A182 GR F44 FLRS000005C 2
SW
250 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SLOP OIL (INCLUDING OILY SLUDGE), SANITARY WATER, TREATED WATER, VENT GAS, OILY WATER,
OILY WATER SEWER, UTILITY WATER, WATER, BLOWDOWN, SOUR WATER
Pipe Material: 6Mo SS/ CS+internal FBE lined Flange Rating: CL 150
Valve Trim: UNS S31254 (upto 1.1/2") / bronze (2" & PWHT: AS PER ASME B31.3
above)
Corrosion Allowance: 0mm (upto 1.1/2") / 3.2mm(2" &above) Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Blind Flange 1/2 - 1.1/2 CL 150 RF ASME B16.5 ASTM A182 GR F44 FLGB000294C 2
251 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SLOP OIL (INCLUDING OILY SLUDGE), SANITARY WATER, TREATED WATER, VENT GAS, OILY WATER,
OILY WATER SEWER, UTILITY WATER, WATER, BLOWDOWN, SOUR WATER
Pipe Material: 6Mo SS/ CS+internal FBE lined Flange Rating: CL 150
Valve Trim: UNS S31254 (upto 1.1/2") / bronze (2" & PWHT: AS PER ASME B31.3
above)
Corrosion Allowance: 0mm (upto 1.1/2") / 3.2mm(2" &above) Code: ASME B31.3 - 2012
Service Type: Special Requirements:
252 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SLOP OIL (INCLUDING OILY SLUDGE), SANITARY WATER, TREATED WATER, VENT GAS, OILY WATER,
OILY WATER SEWER, UTILITY WATER, WATER, BLOWDOWN, SOUR WATER
Pipe Material: 6Mo SS/ CS+internal FBE lined Flange Rating: CL 150
Valve Trim: UNS S31254 (upto 1.1/2") / bronze (2" & PWHT: AS PER ASME B31.3
above)
Corrosion Allowance: 0mm (upto 1.1/2") / 3.2mm(2" &above) Code: ASME B31.3 - 2012
Service Type: Special Requirements:
253 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SLOP OIL (INCLUDING OILY SLUDGE), SANITARY WATER, TREATED WATER, VENT GAS, OILY WATER,
OILY WATER SEWER, UTILITY WATER, WATER, BLOWDOWN, SOUR WATER
Pipe Material: 6Mo SS/ CS+internal FBE lined Flange Rating: CL 150
Valve Trim: UNS S31254 (upto 1.1/2") / bronze (2" & PWHT: AS PER ASME B31.3
above)
Corrosion Allowance: 0mm (upto 1.1/2") / 3.2mm(2" &above) Code: ASME B31.3 - 2012
Service Type: Special Requirements:
254 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SLOP OIL (INCLUDING OILY SLUDGE), SANITARY WATER, TREATED WATER, VENT GAS, OILY WATER,
OILY WATER SEWER, UTILITY WATER, WATER, BLOWDOWN, SOUR WATER
Pipe Material: 6Mo SS/ CS+internal FBE lined Flange Rating: CL 150
Valve Trim: UNS S31254 (upto 1.1/2") / bronze (2" & PWHT: AS PER ASME B31.3
above)
Corrosion Allowance: 0mm (upto 1.1/2") / 3.2mm(2" &above) Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Notes
1: This pipe class is designed for full rating as per Group 2.8 of ASME B16.5 upto NPS 1.5 and Table 1 of ASME B16.42 for NPS 2 and above.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
9: FBE (Fusion Bonded Epoxy) shall be applied internally to the piping after fabrication and fully tested.
10: FBE (Fusion Bonded Epoxy) shall be applied as per Project Specification for Internal Lining (D44-A-RE-380908).
11: Branch connection for size NPS 1.1/2 and below shall be made by providing NPS 2 epoxy lined branch connection with flange
(weldolet/reducing tee as per branch table + 2" FBE Lined Flange) and making the connection with 6Mo Reducing WN Flange.
12: Bronze trim shall have less than 16% zinc.
13: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
255 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SLOP OIL (INCLUDING OILY SLUDGE), SANITARY WATER, TREATED WATER, VENT GAS, OILY WATER,
OILY WATER SEWER, UTILITY WATER, WATER, BLOWDOWN, SOUR WATER
Pipe Material: 6Mo SS/ CS+internal FBE lined Flange Rating: CL 150
Valve Trim: UNS S31254 (upto 1.1/2") / bronze (2" & PWHT: AS PER ASME B31.3
above)
Corrosion Allowance: 0mm (upto 1.1/2") / 3.2mm(2" &above) Code: ASME B31.3 - 2012
Service Type: Special Requirements:
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 SS SS SS SS T
3 SS SS SS SS T1 T
4 SS SS SS SS T1 T1 T
6 SS SS SS SS T3 T1 T1 T
8 SS SS SS SS T3 T3 T1 T1 T
10 SS SS SS SS T3 T3 T3 T1 T1 T
12 SS SS SS SS T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
256 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Size Range 0.5-1.5 0.5-1.5 0.5-1.5 0.5-1.5 2-12 2-12 2-12 2-12
Elbow 45 deg 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 ELGF000040C
Elbow 90 deg 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 ELGN000082C
Tee equal 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 TEGE000025C
257 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Tee reducing 3/4 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 TEGR000032C
Cap 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 CAPG000044C
Coupling reducing 3/4 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 CPLR000039C
258 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Flange SW 1/2 - 1.1/2 CL 150 SW RF ASME B16.5 ASTM A182 GR F44 FLGS000068C 2
Flange SW 1/2 - 1.1/2 CL 300 SW RF ASME B16.5 ASTM A182 GR F44 FLGS000069C 2
Flange reducing
2-2 CL 150 SW FF ASME B16.5 ASTM A182 GR F44 FLRS000005C 2
SW
Blind Flange 1/2 - 1.1/2 CL 150 RF ASME B16.5 ASTM A182 GR F44 FLGB000294C 2
259 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
260 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
261 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.8 of ASME B16.5 upto NPS 1.5 and Table 1 of ASME B16.42 for NPS 2 and above.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
262 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
9: FBE (Fusion Bonded Epoxy) shall be applied internally to the piping after fabrication and fully tested.
10: FBE (Fusion Bonded Epoxy) shall be applied as per Project Specification for Internal Lining (D44-A-RE-380908).
11: Branch connection for size NPS 1.1/2 and below shall be made by providing NPS 2 epoxy lined branch connection with flange
(weldolet/reducing tee as per branch table + 2" FBE Lined Flange) and making the connection with 6Mo Reducing WN Flange.
12: Bronze trim shall have less than 16% zinc.
14: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
263 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 SS SS SS SS T
3 SS SS SS SS T1 T
4 SS SS SS SS T1 T1 T
6 SS SS SS SS T3 T1 T1 T
8 SS SS SS SS T3 T3 T1 T1 T
10 SS SS SS SS T3 T3 T3 T1 T1 T
12 SS SS SS SS T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
264 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2W13
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Elbow 45 deg 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 ELGF000040C
Elbow 90 deg 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 ELGN000082C
Tee equal 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 TEGE000025C
265 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2W13
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Tee reducing 3/4 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 TEGR000032C
Cap 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 CAPG000044C
Coupling reducing 3/4 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 CPLR000039C
266 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2W13
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Flange SW 1/2 - 1.1/2 CL 150 SW RF ASME B16.5 ASTM A182 GR F44 FLGS000068C 2
Flange SW 1/2 - 1.1/2 CL 300 SW RF ASME B16.5 ASTM A182 GR F44 FLGS000069C 2
Flange reducing
2-2 CL 150 SW FF ASME B16.5 ASTM A182 GR F44 FLRS000005C 2
SW
Blind Flange 1/2 - 1.1/2 CL 150 RF ASME B16.5 ASTM A182 GR F44 FLGB000294C 2
267 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2W13
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
268 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2W13
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.8 of ASME B16.5 upto NPS 1.5 and Table 1 of ASME B16.42 for NPS 2 and above.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
269 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2W13
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: All gaskets and valves shall be NSF 14 / NSF 16 certified.
7: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
8: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
9: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
10: FBE (Fusion Bonded Epoxy) shall be applied internally to the piping after fabrication and fully tested.
11: FBE (Fusion Bonded Epoxy) shall be applied as per Project Specification for Internal Lining (D44-A-RE-380908).
12: Branch connection for size NPS 1.1/2 and below shall be made by providing NPS 2 epoxy lined branch connection with flange
(weldolet/reducing tee as per branch table + 2" FBE Lined Flange) and making the connection with 6Mo Reducing WN Flange.
13: Bronze trim shall have less than 16% zinc.
14: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
270 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1LE2W13
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 SS SS SS SS T
3 SS SS SS SS T1 T
4 SS SS SS SS T1 T1 T
6 SS SS SS SS T3 T1 T1 T
8 SS SS SS SS T3 T3 T1 T1 T
10 SS SS SS SS T3 T3 T3 T1 T1 T
12 SS SS SS SS T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
271 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1NT0A01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
272 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1NT0A01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Weldolet 2 - 4 * 1/2 - 1.1/2 MSS SP-97 ASTM B462 UNS N08020 OLTW000072C
273 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1NT0A01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 3.17 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: DELETED
5: DELETED
274 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1NT0A01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: All pipes and fittings shall be in annealed condition.
275 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1NT0A01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1/2 T
RUN PIPE
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T3 T3 T1 T1 T
3 T3 T3 T3 T1 T1 T
4 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
276 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1NT0A02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
277 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1NT0A02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 3.17 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
5: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
6: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
7: All pipes and fittings shall be in annealed condition.
8: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
278 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1NT0A02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1/2 T
RUN PIPE
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T3 T3 T1 T1 T
3 T3 T3 T3 T1 T1 T
4 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
279 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1PK0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Sch/WT
Pipe PVDF 3/4 - 2 SDR 21 socket fusion jt ISO 10931 ASTM D3222 type I GR2 PIPP000001C
280 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1PK0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: DELETED
2: DELETED
281 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1PK0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1 T1 T
1.1/2 T1 T1 T
ABBREVIATIONS:
282 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
283 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
284 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
285 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
286 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.2 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
5: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
6: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
7: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
8: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
9: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the valve
at valve vendor shop.
10: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
11: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
287 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T4 T4 T1 T1 T
3 T4 T4 T4 T1 T1 T
4 T4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
288 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, 60PSIG LLP STEAM, ACID GAS, PROCESS AIR, RELIEF LINE, SEAL OIL, PRESSURISED
SEWARE, OILY WATER
SERVICE LIMITS
Size Range 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 26-30 26-30
Sch/WT Sch40S Sch40S Sch40S Sch40S Sch40S Sch80S Sch10S Sch10S Sch10S Sch80S Sch10S Sch10S
Size 12 14 16 18 20 24 26 28 30
Sch/WT Sch10S Sch10S Sch10S Sch10S Sch10S Sch10S 6.35mm Sch10 Sch10S
289 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, 60PSIG LLP STEAM, ACID GAS, PROCESS AIR, RELIEF LINE, SEAL OIL, PRESSURISED
SEWARE, OILY WATER
290 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, 60PSIG LLP STEAM, ACID GAS, PROCESS AIR, RELIEF LINE, SEAL OIL, PRESSURISED
SEWARE, OILY WATER
291 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, 60PSIG LLP STEAM, ACID GAS, PROCESS AIR, RELIEF LINE, SEAL OIL, PRESSURISED
SEWARE, OILY WATER
292 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, 60PSIG LLP STEAM, ACID GAS, PROCESS AIR, RELIEF LINE, SEAL OIL, PRESSURISED
SEWARE, OILY WATER
293 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, 60PSIG LLP STEAM, ACID GAS, PROCESS AIR, RELIEF LINE, SEAL OIL, PRESSURISED
SEWARE, OILY WATER
294 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, 60PSIG LLP STEAM, ACID GAS, PROCESS AIR, RELIEF LINE, SEAL OIL, PRESSURISED
SEWARE, OILY WATER
295 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, 60PSIG LLP STEAM, ACID GAS, PROCESS AIR, RELIEF LINE, SEAL OIL, PRESSURISED
SEWARE, OILY WATER
296 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, 60PSIG LLP STEAM, ACID GAS, PROCESS AIR, RELIEF LINE, SEAL OIL, PRESSURISED
SEWARE, OILY WATER
297 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, 60PSIG LLP STEAM, ACID GAS, PROCESS AIR, RELIEF LINE, SEAL OIL, PRESSURISED
SEWARE, OILY WATER
298 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, 60PSIG LLP STEAM, ACID GAS, PROCESS AIR, RELIEF LINE, SEAL OIL, PRESSURISED
SEWARE, OILY WATER
Notes
1: This pipe class is designed for full rating as per Group 2.2 of ASME B16.5 upto NPS 24. For NPS 26 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
299 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, 60PSIG LLP STEAM, ACID GAS, PROCESS AIR, RELIEF LINE, SEAL OIL, PRESSURISED
SEWARE, OILY WATER
5: Ball and Butterfly Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F
(180 deg C) shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of
same to be restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be
used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: All material shall meet the requirements of NACE MR0175/ISO 15156.
9: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
10: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
11: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
300 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SOUR WATER, 60PSIG LLP STEAM, ACID GAS, PROCESS AIR, RELIEF LINE, SEAL OIL, PRESSURISED
SEWARE, OILY WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, Toxic
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T3 T3 T1, T1 T
T1
3 T3 T3 T3 T1 T1 T
4 T3 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T3 T1 T1 T
8 T3 T3 T3 T3 T3 T3 T1 T1 T
10 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
12 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
14 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
16 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
24 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T
26 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T1 T
28 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T1 T1 T
30 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T1 T1 T1 T
ABBREVIATIONS:
301 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, Toxic,
Lethal Service
SERVICE LIMITS
Size Range 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 0.5-24 26-76 26-76 26-76 26-76
Temperature (ºF) - -50 100 200 300 400 460 - 350 405 460
FV upto
18", HV
Pressure (Psig) 275 275 235 215 195 180 HV 160 155 125
above
20"
Sch/WT Sch40S Sch40S Sch40S Sch40S Sch40S Sch10S Sch10S Sch10S Sch10S Sch10S Sch10S Sch10S
Size 16 18 20 24 26 28 30 32 34 36 38 40
Sch/WT Sch10S Sch10S Sch10S Sch10S 6.35mm Sch10 Sch10S 6.35mm 7.14mm 7.14mm 7.92mm 7.92mm
Size 42 44 46 48 52 56 60 64 68 72 76
Sch/WT 8.74mm 8.74mm STD STD 10.31mm 11.13mm 11.91mm 12.70mm 13.6mm 14.27mm 15.09mm
302 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, Toxic,
Lethal Service
303 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, Toxic,
Lethal Service
304 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, Toxic,
Lethal Service
305 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, Toxic,
Lethal Service
306 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, Toxic,
Lethal Service
307 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, Toxic,
Lethal Service
308 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, Toxic,
Lethal Service
309 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, Toxic,
Lethal Service
310 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, Toxic,
Lethal Service
311 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, Toxic,
Lethal Service
312 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, Toxic,
Lethal Service
313 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, Toxic,
Lethal Service
314 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, Toxic,
Lethal Service
315 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: NACE MR0175/ISO 15156 Special Requirements: NACE MR 0175 / ISO 15156, Toxic,
Lethal Service
Notes
1: This pipe class is designed for full rating as per Group 2.2 of ASME B16.5 upto NPS 24. For NPS 26 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in
P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
5: Ball and Butterfly Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F
(180 deg C) shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of
same to be restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be
used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: All material shall meet the requirements of NACE MR0175/ISO 15156.
9: Flanges, Blind Flanges not covered by ASME B16.5 / ASME B16.47 shall be designed and fabricated according to ASME VIII, div. 1. Refer
Appendix 3 for Special flange drawings.
10: This pipe class is applicable for Category M service and shall comply to ASME B31.3, Chapter VIII requirements.
11: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
12: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Helium.
13: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
316 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
1 T1 T
1.1/2 T1 T1 T
2 T3 T1 T1 T
3 T3 T3 T1 T1 T
4 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T1 T1 T
8 T3 T3 T3 T3 T3 T1 T1 T
10 T3 T3 T3 T3 T3 T3 T1 T1 T
12 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
14 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
16 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
24 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T
30 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR T1 T1 T1 T1 T
36 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR T1 T1 T1 T
40 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T
42 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T1 T
48 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T
52 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T
56 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T1 T
60 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T
64 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T
68 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T
72 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T
76 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T1 T
1 TLR TL
1.1/2 TLR TLR TL
2 T8 TLR TLR TL
3 T8 T8 TLR TLR TL
4 T8 T8 T8 TLR TLR TL
6 T8 T8 T8 T8 TLR TLR TL
8 T8 T8 T8 T8 T8 TLR TLR TL
10 T8 T8 T8 T8 T8 T8 TLR TLR TL
12 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
14 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
16 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
18 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TL
20 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TLR TL
24 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TLR TLR TLR TLR TL
30 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TLR TLR TLR TLR TL
36 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TLR TLR TLR TL
40 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TLR TLR TLR TL
42 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TL
48 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TL
52 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TL
56 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TL
60 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TLR TL
64 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TLR TL
68 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TLR TLR TL
72 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TLR TLR TL
76 T8 T8 T8 T8 T8 T8 T8 T8 T8 T8 TR1 TR1 TR1 TR1 TR1 TR1 TR1 TLR TLR TLR TLR TLR TLR TLR TLR TLR TL
317 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P10
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: ACID GAS, LOW PRESSURE FUEL GAS, HIGH PRESSURE FLARE, LOW PRESSURE FLARE, 60 PSIG LLP
STEAM, SOUR WATER
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
TL: Equal Tee - 45 Deg
TLR: Reducing Tee - 45 Deg
TR1: Stub in Connection with Full encirclement sleeve - 45 Deg
T8: Latrolet
318 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P11
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Sch/WT Sch40S Sch40S Sch40S Sch40S Sch40S Sch10S Sch10S Sch10S Sch10S Sch10S Sch10S Sch10S
Size 16 18 20
319 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P11
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
320 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P11
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
321 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P11
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
322 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P11
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
323 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P11
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
324 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P11
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.2 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball and Butterfly Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F
(180 deg C) shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of
same to be restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be
used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
325 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0P11
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
9: Sealing material requirement for Amine Service shall be as per Project Specification Material Requirement for CRA, CS and Low Alloy Steel
(For piping, fittings, flanges & valves), Doc.No. D44-A-RE-380920.
10: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
11: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
12: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
326 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHEMICAL (INCLUDING AMINE), CHEMICAL (SCALE INHIBITOR), CHEMICAL (CORROSSION INHIBITOR),
CHEMICAL (PHOSPHATE)
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
SERVICE LIMITS
327 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHEMICAL (INCLUDING AMINE), CHEMICAL (SCALE INHIBITOR), CHEMICAL (CORROSSION INHIBITOR),
CHEMICAL (PHOSPHATE)
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
328 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHEMICAL (INCLUDING AMINE), CHEMICAL (SCALE INHIBITOR), CHEMICAL (CORROSSION INHIBITOR),
CHEMICAL (PHOSPHATE)
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
329 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHEMICAL (INCLUDING AMINE), CHEMICAL (SCALE INHIBITOR), CHEMICAL (CORROSSION INHIBITOR),
CHEMICAL (PHOSPHATE)
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
330 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHEMICAL (INCLUDING AMINE), CHEMICAL (SCALE INHIBITOR), CHEMICAL (CORROSSION INHIBITOR),
CHEMICAL (PHOSPHATE)
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Notes
1: This pipe class is designed for full rating as per Group 2.2 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: DELETED
5: DELETED
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
331 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: CHEMICAL (INCLUDING AMINE), CHEMICAL (SCALE INHIBITOR), CHEMICAL (CORROSSION INHIBITOR),
CHEMICAL (PHOSPHATE)
Pipe Material: SS Flange Rating: CL 150
Valve Trim: trim 12 PWHT: NO
Corrosion Allowance: 0MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
3/4 T
RUN PIPE
1 T1 T
1.1/2 T1 T1 T
2 T3 T1 T1 T
3 T3 T3 T1 T1 T
4 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T1 T1 T
8 T3 T3 T3 T3 T3 T1 T1 T
10 T3 T3 T3 T3 T3 T3 T1 T1 T
12 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
332 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
333 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
334 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
335 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
336 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
337 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
338 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.2 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball and Butterfly Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F
(180 deg C) shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of
same to be restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be
used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
339 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
9: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the valve
at valve vendor shop.
10: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
11: Gaskets and valves shall be NSF 14 / NSF 16 certified for Drinking Water service.
12: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
340 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SD0W01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T
RUN PIPE
1 T1 T
1.1/2 T1 T1 T
2 T4 T1 T1 T
3 T4 T4 T1 T1 T
4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
341 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SX0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Temperature
Core 32 100 200 300 356
(ºF)
Pressure
275 275 235 215 203.8
(Psig)
Size Range 0.5-14 0.5-14 0.5-14 0.5-14 0.5-14 0.5-14
Temperature
Jacket 32 100 200 300 395 -
(ºF)
Pressure
275 275 235 215 196 FV
(Psig)
Size 1 1.1/2 2 3 4 6 8 10
Sch/WT Sch30
342 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SX0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
343 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SX0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
344 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SX0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.2 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
4: Gate Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for process
drain/vent.
5: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
6: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
7: Steam Jacket to be designed at least one size larger than the inner pipe.
8: Jacket pipe is designed for low pressure steam (maximum 150 psig) with1.6 mm corrosion allowance
9: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
10: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
11: Sleved Plug Valves shall be used up to design temperature 428 deg F(220 deg C).
12: For Core piping, all materials shall meet the requirements of NACE MR0175/ISO 15156.
345 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SX0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1 T
RUN PIPE
1.1/2 T
2 T4 T
3 T4 T
4 T4 T
6 T4 T
8 T4 T
10 T4 T
12 T4 T
ABBREVIATIONS:
346 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SP0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Elbow 45 deg 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F51 ELGF000013C
Elbow 90 deg 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F51 ELGN000026C
Tee equal 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F51 TEGE000008C
347 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SP0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Tee reducing 3/4 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F51 TEGR000015C
Cap 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F51 CAPG000013C
Coupling reducing 1 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F51 CPLR000013C
348 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SP0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Sockolet 2 - 12 * 1/2 - 1.1/2 CL 3000 MSS SP-97 ASTM A182 GR F51 OLTS000004C
Flange SW 1/2 - 1.1/2 CL 150 SW RF ASME B16.5 ASTM A182 GR F51 FLGS000051C 2
Blind Flange 1/2 - 12 CL 150 RF ASME B16.5 ASTM A182 GR F51 FLGB000026C 2
349 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SP0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
350 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SP0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
351 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SP0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.8 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
352 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SP0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
5: Ball and Butterfly Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F
(180 deg C) shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of
same to be restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be
used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
9: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the valve
at valve vendor shop.
10: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
11: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
353 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SP0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T4 T4 T1 T1 T
3 T4 T4 T4 T1 T1 T
4 T4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
354 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SP0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Sch/WT Sch40S Sch40S Sch40S Sch40S Sch10S Sch10S Sch10S Sch10S Sch10S Sch10S
355 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SP0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
356 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SP0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
357 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SP0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.8 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
358 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SP0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: DELETED
5: DELETED
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: All material shall meet the requirements of NACE MR0175/ISO 15156.
9: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
10: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
359 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SP0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T
RUN PIPE
1 T1 T
1.1/2 T1 T1 T
2 T3 T1 T1 T
3 T3 T3 T1 T1 T
4 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T1 T1 T
8 T3 T3 T3 T3 T3 T1 T1 T
10 T3 T3 T3 T3 T3 T3 T1 T1 T
12 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
360 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SV0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
361 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SV0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
362 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SV0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
363 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SV0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
364 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SV0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.8 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: DELETED
5: DELETED
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: All material shall meet the requirements of NACE MR0175/ISO 15156.
9: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
365 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SV0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T
RUN PIPE
1 T1 T
1.1/2 T1 T1 T
2 T3 T1 T1 T
3 T3 T3 T1 T1 T
4 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T1 T1 T
8 T3 T3 T3 T3 T3 T1 T1 T
10 T3 T3 T3 T3 T3 T3 T1 T1 T
12 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
366 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SV0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Elbow 45 deg 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 ELGF000040C
Elbow 90 deg 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 ELGN000082C
Tee equal 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 TEGE000025C
367 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SV0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Tee reducing 3/4 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 TEGR000032C
Cap 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 CAPG000044C
Coupling reducing 3/4 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 CPLR000039C
368 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SV0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Sockolet 2 - 12 * 1/2 - 1.1/2 CL 3000 MSS SP-97 ASTM A182 GR F44 OLTS000098C
Flange SW 1/2 - 1.1/2 CL 150 SW RF ASME B16.5 ASTM A182 GR F44 FLGS000068C 2
Flange SW 1/2 - 1.1/2 CL 300 SW RF ASME B16.5 ASTM A182 GR F44 FLGS000069C 2,6
Blind Flange 1/2 - 12 CL 150 RF ASME B16.5 ASTM A182 GR F44 FLGB000294C 2
369 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SV0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
370 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SV0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
371 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SV0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.8 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball and Butterfly Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F
(180 deg C) shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of
same to be restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be
used.
6: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
9: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the valve
at valve vendor shop.
10: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
11: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
372 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
1SV0P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T4 T4 T1 T1 T
3 T4 T4 T4 T1 T1 T
4 T4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
373 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Sch/WT Sch160 Sch160 XS XS XS STD STD STD STD STD Sch40 Sch40
Size 16
Sch/WT Sch40
374 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
375 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Sockolet 2 - 16 * 1/2 - 3/4 CL 6000 MSS SP-97 ASTM A350 GR LF2 CL1 OLTS000008C
Sockolet 3 - 16 * 1 - 1.1/2 CL 3000 MSS SP-97 ASTM A350 GR LF2 CL1 OLTS000007C
376 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Flange SW 1/2 - 1.1/2 CL 300 SW RF ASME B16.5 ASTM A350 GR LF2 CL1 FLGS000005C 2
Blind Flange 1/2 - 16 CL 300 RF ASME B16.5 ASTM A350 GR LF2 CL1 FLGB000034C 2
377 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
378 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
379 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.3 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
380 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
7: Valves for low temperature service shall confirm to the requirements of 04-SAMSS-003.
8: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
9: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the valve
at valve vendor shop.
10: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
11: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
381 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CA1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1/2 T
RUN PIPE
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T4 T1 T1 T
3 T4 T4 T1 T1 T
4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
14 T4 T4 T4 T3 T3 T3 T3 T3 T1 T1 T
16 T4 T4 T4 T3 T3 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
382 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SULFUR
Pipe Material: CS Flange Rating: CL 300
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
SERVICE LIMITS
Size 16
Sch/WT XS
Elbow 45 deg 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGF000026C
383 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SULFUR
Pipe Material: CS Flange Rating: CL 300
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Elbow 90 deg 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGN000070C
Tee equal 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N TEGE000013C
Tee reducing 3/4 - 1.1/2 CL 9000 SW ASME B16.11 ASTM A105N TEGR000020C
Tee reducing 1.1/2 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N TEGR000017C
384 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SULFUR
Pipe Material: CS Flange Rating: CL 300
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Coupling reducing 1.1/2 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N CPLR000022C
Nipoflange 2 - 16 * 3/4 - 2 CL 300 RF mfg std ASTM A105N 200mm long OLTF000292C 2
Nipoflange 2 - 16 * 3/4 - 2 CL 300 RF mfg std ASTM A105N 150mm long OLTF000294C 2
385 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SULFUR
Pipe Material: CS Flange Rating: CL 300
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Spectacle Blank 3/4 - 1.1/2 CL 300 FF ASME B16.48 ASTM A516 GR 70 LBKB000353C 2
386 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SULFUR
Pipe Material: CS Flange Rating: CL 300
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
387 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SULFUR
Pipe Material: CS Flange Rating: CL 300
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
388 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SULFUR
Pipe Material: CS Flange Rating: CL 300
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
389 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SULFUR
Pipe Material: CS Flange Rating: CL 300
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
390 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SULFUR
Pipe Material: CS Flange Rating: CL 300
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
391 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SULFUR
Pipe Material: CS Flange Rating: CL 300
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the valve
at valve vendor shop.
9: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
10: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
11: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
392 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: SULFUR
Pipe Material: CS Flange Rating: CL 300
Valve Trim: trim 8 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
1/2 T
RUN PIPE
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T4 T4 T1 T1 T
3 T4 T4 T4 T1 T1 T
4 T4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
14 T4 T4 T4 T4 T3 T3 T3 T3 T3 T1 T1 T
16 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
393 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Size 16 18 20 24 26 28 30
394 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
395 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
396 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
397 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
398 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
399 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 16. For NPS 18 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
400 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in
P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
5: Ball and Butterfly Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F
(180 deg C) shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of
same to be restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be
used.
6: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
7: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
8: All material shall meet the requirements of NACE MR0175/ISO 15156.
9: All welds for all wall thicknesses including those made in manufacture and repair shall require PWHT.
10: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
11: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
12: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
13: Material for weld neck flanges upto NPS 24 is ASTM A105N and NPS 26 and above is ASTM A350 LF2 CL.2 as per SAES-L-109, Table-2.
401 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P06
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T3 T1 T1 T
3 T3 T3 T1 T1 T
4 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T1 T1 T
8 T3 T3 T3 T3 T3 T1 T1 T
10 T3 T3 T3 T3 T3 T3 T1 T1 T
12 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
14 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
16 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T1 T
20 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T1 T1 T
24 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T1 T1 T
26 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3
28 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3
30 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3
ABBREVIATIONS:
402 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Size Range 0.5-16 0.5-16 0.5-16 0.5-16 0.5-16 0.5-16 18-60 18-60
Size 16 18 20 24 26 28 30 32 34 36 38 40
Sch/WT XS STD STD 11.13mm 11.13mm 11.91mm XS XS 14.27mm 14.27mm 14.27mm 15.88mm
Size 42 44 46 48 52 56 60
403 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
404 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
405 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
406 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
407 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
408 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 16. For NPS 18 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in
P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
7: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
8: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
9: Material for weld neck flanges upto NPS 24 is ASTM A105N and NPS 26 and above is ASTM A350 LF2 CL.2 as per SAES-L-109, Table-2.
10: All material shall meet the requirements of NACE MR0175/ISO 15156.
11: All welds for all wall thicknesses including those made in manufacture and repair shall require PWHT.
12: This pipe class is applicable for Category M service and shall comply to ASME B31.3, Chapter VIII requirements.
13: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Helium.
14: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
409 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P09
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T3 T3 T1 T1 T
3 T3 T3 T3 T1 T1 T
4 T3 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T3 T1 T1 T
8 T3 T3 T3 T3 T3 T3 T1 T1 T
10 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
12 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
14 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
16 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
24 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T
26 T1 T1 T1 T1 T1 T1
28 T1 T1 T1 T1 T1 T1 T1
30 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR T1 T1 T1 T1 T1 T1 T
32 T1 T1 T1 T1 T1 T1 T1 T1
34 T1 T1 T1 T1 T1 T1 T1 T1
36 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR T1 T1 T1 T1 T1 T1 T1 T
38 T1 T1 T1 T1 T1 T1 T1 T1 T1
40 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T
42 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T1 T
44 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1
46 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1
48 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 T
52 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T
56 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T1 T
60 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 TR TR TR TR TR T1 T1 T1 T1 T1 T1 T1 T
ABBREVIATIONS:
410 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Size 16 18
Sch/WT XS Sch20
411 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
412 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
413 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
414 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
415 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 16. For NPS 18 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in
P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
5: Ball and Butterfly Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F
(180 deg C) shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of
same to be restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be
used.
6: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
7: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
416 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
9: Sealing material requirement for Amine Service shall be as per Project Specification Material Requirement for CRA, CS and Low Alloy Steel
(For piping, fittings, flanges & valves), Doc.No. D44-A-RE-380920.
10: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
11: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
417 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3CT2P12
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1/2 T
RUN PIPE
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T3 T3 T1 T1 T
3 T3 T3 T3 T1 T1 T
4 T3 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T3 T1 T1 T
8 T3 T3 T3 T3 T3 T3 T1 T1 T
10 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
12 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
14 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
16 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
418 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3LE2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Elbow 45 deg 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 ELGF000040C
Elbow 90 deg 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 ELGN000082C
Tee equal 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 TEGE000025C
419 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3LE2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Tee reducing 3/4 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 TEGR000032C
Cap 1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 CAPG000044C
Coupling reducing 3/4 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A182 GR F44 CPLR000039C
420 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3LE2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Flange SW 1/2 - 1.1/2 CL 300 SW RF ASME B16.5 ASTM A182 GR F44 FLGS000069C 2
421 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3LE2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.8 of ASME B16.5 upto NPS 1.5 and Table 1 of ASME B16.42 for NPS 2 and above.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
7: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
422 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3LE2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
8: FBE (Fusion Bonded Epoxy) shall be applied internally to the piping after fabrication and fully tested.
9: FBE (Fusion Bonded Epoxy) shall be applied as per Project Specification for Internal Lining (D44-A-RE-380908).
10: Branch connection for size NPS 1.1/2 and below shall be made by providing NPS 2 epoxy lined branch connection with flange
(weldolet/reducing tee as per branch table + 2" FBE Lined Flange) and making the connection with 6Mo Reducing WN Flange.
11: Bronze trim shall have less than 16% zinc.
12: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
423 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3LE2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Valve Trim: UNS31254 (upto 1.1/2") / bronze (2" & PWHT: AS PER ASME B31.3
above)
Corrosion Allowance: 0mm (up to 1.1/2") / 3.2mm (2" & above) Code: ASME B31.3 - 2012
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 SS SS SS SS T
3 SS SS SS SS T1 T
4 SS SS SS SS T1 T1 T
6 SS SS SS SS T3 T1 T1 T
8 SS SS SS SS T3 T3 T1 T1 T
10 SS SS SS SS T3 T3 T3 T1 T1 T
12 SS SS SS SS T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
T: Equal Tee
T1: Reducing Tee
T3: Weldolet
T4: Sockolet
T5: Threadolet
T6: Nipolet
TP: Sweepolet
TR: Stub in Connection with RPAD
424 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Size Range 0.5-2 0.5-2 0.5-2 0.5-2 0.5-2 0.5-2 3-18 3-18 3-18 3-18
Temperature (ºF) 100 200 300 32 400 460 190 284 290 460
Pressure (Psig) 720 620 560 720 515 494 284 407 300 320
Sch/WT Sch40S Sch40S Sch40S Sch40S Sch40S Sch10S Sch10S Sch10S Sch10S Sch10S Sch10S Sch10S
Size 16 18
425 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
426 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
427 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
428 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
429 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.2 of ASME B16.5 upto NPS 2. For NPS 3 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in
P&ID.
4: DELETED
5: DELETED
6: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
7: All material shall meet the requirements of NACE MR0175/ISO 15156.
8: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
9: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
430 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
431 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T1 T
RUN PIPE
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T3 T3 T1 T1 T
3 T3 T3 T3 T1 T1 T
4 T3 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T3 T1 T1 T
8 T3 T3 T3 T3 T3 T3 T1 T1 T
10 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
12 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
14 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
16 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
432 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0P11
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Sch/WT Sch40S Sch40S Sch40S Sch40S Sch40S Sch10S Sch10S Sch10S Sch10S Sch10S Sch10S Sch10S
Size 16 18
433 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0P11
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
434 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0P11
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
435 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0P11
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
436 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0P11
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
437 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0P11
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
438 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0P11
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.2 of ASME B16.5 upto NPS 2. For NPS 3 and above, pipe class is designed for line
design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in
P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
7: All material shall meet the requirements of NACE MR0175/ISO 15156.
8: Sealing material requirement for Amine Service shall be as per Project Specification Material Requirement for CRA, CS and Low Alloy Steel
(For piping, fittings, flanges & valves), Doc.No. D44-A-RE-380920.
9: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
10: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
11: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
439 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0P11
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T
RUN PIPE
1 T1 T
1.1/2 T1 T1 T
2 T3 T1 T1 T
3 T3 T3 T1 T1 T
4 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T1 T1 T
8 T3 T3 T3 T3 T3 T1 T1 T
10 T3 T3 T3 T3 T3 T3 T1 T1 T
12 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
14 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
16 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T3 T3 T3 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
440 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
441 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.2 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: Class 300 rated flanges/gaskets/bolts shall be used to mate with 300# instrument valves, equipment connections only.
5: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
442 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
3SD0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1/2 T
RUN PIPE
3/4 T
1 T
1.1/2 T
ABBREVIATIONS:
443 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Size 16 18 20
Elbow 45 deg 1/2 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N ELGF000024C
444 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Elbow 90 deg 1/2 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N ELGN000069C
Tee equal 1/2 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N TEGE000010C
Tee reducing 3/4 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N TEGR000017C
Tee reducing 1.1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A105N TEGR000012C
445 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Coupling reducing 1.1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A105N CPLR000021C
Nipoflange 2 - 20 * 3/4 - 2 CL 600 RF mfg std ASTM A105N 200mm long OLTF000442C 2
Nipoflange 2 - 20 * 3/4 - 2 CL 600 RF mfg std ASTM A105N 150mm long OLTF000444C 2
446 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
447 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Spectacle Blank 3/4 - 1.1/2 CL 600 FF ASME B16.48 ASTM A516 GR 70 LBKB000351C 2
448 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
449 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
450 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 8. For NPS 10 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
451 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
6: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the valve
at valve vendor shop.
9: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
10: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
11: Material for weld neck flanges upto NPS 12 is ASTM A105N and NPS 14 and above is ASTM A350 LF2 CL.2 as per SAES-L-109, Table-2.
12: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
452 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1/2 T
RUN PIPE
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T4 T4 T1 T1 T
3 T4 T4 T4 T1 T1 T
4 T4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
14 T4 T4 T4 T4 T3 T3 T3 T3 T3 T1 T1 T
16 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
ABBREVIATIONS:
453 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Size Range 0.5-6 0.5-6 0.5-6 0.5-6 0.5-6 0.5-6 0.5-6 8-36 8-36
Size 16 18 20 24 26 28 30 32 34 36
Sch/WT 14.27mm 15.88mm 17.48mm 20.62mm 20.62mm 21.8mm 23.83mm 25.40mm 25.40mm 26.97mm
Elbow 45 deg 3/4 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N ELGF000024C
454 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Elbow 90 deg 3/4 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N ELGN000069C
Tee equal 3/4 - 3/4 CL 6000 SW ASME B16.11 ASTM A105N TEGE000010C
455 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Tee reducing 1.1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A105N TEGR000012C
456 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Coupling reducing 1.1/2 - 1.1/2 CL 3000 SW ASME B16.11 ASTM A105N CPLR000021C
Nipoflange 2 - 36 * 3/4 - 2 CL 600 RF mfg std ASTM A105N 200mm long OLTF000442C 2
Nipoflange 2 - 36 * 3/4 - 2 CL 600 RF mfg std ASTM A105N 150mm long OLTF000444C 2
457 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
458 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Spectacle Blank 3/4 - 1.1/2 CL 600 FF ASME B16.48 ASTM A516 GR 70 LBKB000351C 2
459 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
460 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
461 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
462 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
463 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
464 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 6. For NPS 8 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
The flange face finish of Ring Joint Type flanges shall be not exceed 63 micro-inches (1.6 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in
P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the
valve at valve vendor shop.
465 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
9: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
10: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
11: All welded pipes and fittings shall be 100% radiographed and have a joint efficiency factor of 1.
12: Material for weld neck flanges upto NPS 12 is ASTM A105N and NPS 14 and above is ASTM A350 LF2 CL.2 as per SAES-L-109, Table-2.
13: For steam service, NPS 2 & larger Gate valve shall be Parallel slide gate valve with Cavity pressure relief system as per SAES-L-108,
Clause 7.12.
14: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
466 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1 T1 T
1.1/2 T1 T1 T
2 T4 T1 T1 T
3 T4 T4 T1 T1 T
4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
14 T4 T4 T4 T3 T3 T3 T3 T3 T1 T1 T
16 T4 T4 T4 T3 T3 T3 T3 T3 T3 T1 T1 T
18 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T
20 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T
24 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 T1 T1 T1 T1 T
30 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR T1 T1 T1 T1 T
36 T4 T4 T4 T3 T3 T3 T3 T3 T3 T3 TR TR TR T1 T1 T1 T1 T1 T
ABBREVIATIONS:
467 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Elbow 45 deg 3/4 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGF000026C
Elbow 90 deg 3/4 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGN000070C
468 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Tee equal 3/4 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N TEGE000013C
Tee reducing 1.1/2 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N TEGR000017C
469 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Coupling reducing 1.1/2 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N CPLR000022C
Nipoflange 2 - 10 * 3/4 - 2 CL 600 RF mfg std ASTM A105N 200mm long OLTF000442C 2
Nipoflange 2 - 10 * 3/4 - 2 CL 600 RF mfg std ASTM A105N 150mm long OLTF000444C 2
470 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Spectacle Blank 3/4 - 1.1/2 CL 600 FF ASME B16.48 ASTM A516 GR 70 LBKB000351C 2
471 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
472 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
473 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5 upto NPS 8. For NPS 10 and above, pipe class is designed for line
design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore Ball
valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
6: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the valve
at valve vendor shop.
9: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
10: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
11: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
474 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2P01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1 T1 T
1.1/2 T1 T1 T
2 T4 T1 T1 T
3 T4 T4 T1 T1 T
4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
475 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BOILER FEED WATER, 600 PSIG H.P. CONDENSATE, 600 PSIG HP STEAM
Pipe Material: CS Flange Rating: CL 600
Valve Trim: trim 5 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
SERVICE LIMITS
Size Range 0.5-8 0.5-8 0.5-8 0.5-8 0.5-8 0.5-8 0.5-8 10-18 10-18
Size 16 18
Elbow 45 deg 3/4 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGF000026C
Elbow 90 deg 3/4 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N ELGN000070C
476 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BOILER FEED WATER, 600 PSIG H.P. CONDENSATE, 600 PSIG HP STEAM
Pipe Material: CS Flange Rating: CL 600
Valve Trim: trim 5 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Tee equal 1/2 - 3/4 CL 9000 SW ASME B16.11 ASTM A105N TEGE000013C
Tee reducing 3/4 - 1.1/2 CL 9000 SW ASME B16.11 ASTM A105N TEGR000020C
Tee reducing 1.1/2 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N TEGR000017C
477 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BOILER FEED WATER, 600 PSIG H.P. CONDENSATE, 600 PSIG HP STEAM
Pipe Material: CS Flange Rating: CL 600
Valve Trim: trim 5 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Coupling reducing 1.1/2 - 1.1/2 CL 6000 SW ASME B16.11 ASTM A105N CPLR000022C
Nipoflange 2 - 18 * 3/4 - 2 CL 600 RF mfg std ASTM A105N 150mm long OLTF000444C 2
478 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BOILER FEED WATER, 600 PSIG H.P. CONDENSATE, 600 PSIG HP STEAM
Pipe Material: CS Flange Rating: CL 600
Valve Trim: trim 5 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Nipoflange 2 - 8 * 3/4 - 2 CL 600 RF mfg std ASTM A105N 200mm long OLTF000442C 2
479 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BOILER FEED WATER, 600 PSIG H.P. CONDENSATE, 600 PSIG HP STEAM
Pipe Material: CS Flange Rating: CL 600
Valve Trim: trim 5 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Flange reducing
8-8 CL 600 WN RF ASME B16.5 ASTM A105N FLRW000083C 2
WN
Spectacle Blank 1/2 - 1.1/2 CL 600 FF ASME B16.48 ASTM A516 GR 70 LBKB000351C 2
480 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BOILER FEED WATER, 600 PSIG H.P. CONDENSATE, 600 PSIG HP STEAM
Pipe Material: CS Flange Rating: CL 600
Valve Trim: trim 5 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
481 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BOILER FEED WATER, 600 PSIG H.P. CONDENSATE, 600 PSIG HP STEAM
Pipe Material: CS Flange Rating: CL 600
Valve Trim: trim 5 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
482 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BOILER FEED WATER, 600 PSIG H.P. CONDENSATE, 600 PSIG HP STEAM
Pipe Material: CS Flange Rating: CL 600
Valve Trim: trim 5 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
483 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BOILER FEED WATER, 600 PSIG H.P. CONDENSATE, 600 PSIG HP STEAM
Pipe Material: CS Flange Rating: CL 600
Valve Trim: trim 5 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
Notes
1: This pipe class is designed for full rating as per Group 1.1 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in
P&ID.
4: All Ball valves up to NPS 1.1/2 shall be full bore. For NPS 2 and above, Reduced bore Ball valves shall be used as default. Use full bore
Ball valves only when specified in P&ID.
5: Ball Valves with line design temperature up to and including 356 deg F (180 deg C) shall be soft seated and above 356 deg F (180 deg C)
shall be metal seated valves. P-T rating of soft seat & seal material to be verified with seat-seal vendor & accordingly usage of same to be
restricted to that temperature. For temperature above recommended temperature by vendor, metal seat ball valves shall be used.
484 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BOILER FEED WATER, 600 PSIG H.P. CONDENSATE, 600 PSIG HP STEAM
Pipe Material: CS Flange Rating: CL 600
Valve Trim: trim 5 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
6: Gate and Ball Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for
process drain/vent.
7: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
8: Soft seated SW Ball Valves shall be provided with 100mm pup piece of material and wall thickness same as mating pipe, welded to the
valve at valve vendor shop.
9: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
10: Carbon steel pipes and wrought components with nominal wall thickness greater than 25mm shall be Charpy impact tested at 32 deg F (0
deg C) in accordance with ASME B31.3 with impact values being 34J min average and 27J min individual for a standard 10mm x 10mm
specimen. Impact testing shall be carried out on the base metal, weld deposit and the Heat affected zone.
11: For steam service, NPS 2 & larger Gate valve shall be Parallel slide gate valve with Cavity pressure relief system as per SAES-L-108,
Clause 7.12.
12: All soft seat valves shall be firesafe design as per API 607/ API 6FA / ISO 10497.
485 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6CS2U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Services: BOILER BLOWDOWN, BOILER FEED WATER, 600 PSIG H.P. CONDENSATE, 600 PSIG HP STEAM
Pipe Material: CS Flange Rating: CL 600
Valve Trim: trim 5 PWHT: AS PER ASME B31.3
Corrosion Allowance: 3.2MM Code: ASME B31.3 - 2012
Service Type: Special Requirements:
1/2 T
RUN PIPE
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T4 T4 T1 T1 T
3 T4 T4 T4 T1 T1 T
4 T4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T4 T3 T3 T1 T1 T
10 T
12 T
14 T
16 T
18 T
ABBREVIATIONS:
486 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6SD0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
487 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6SD0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.2 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
488 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6SD0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
5: Gate valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for process
drain/vent.
489 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6SD0U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T1 T
1 T1 T1 T
ABBREVIATIONS:
490 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6SP0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
491 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6SP0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
492 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6SP0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
493 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6SP0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
494 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6SP0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 2.8 of ASME B16.5.
2: The flange face finish of Raised Face flanges shall be 125 to 250 micro-inches (3.2 to 6.3 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in P&ID.
4: DELETED
5: DELETED
6: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
7: All material shall meet the requirements of NACE MR0175/ISO 15156.
8: All valves shall meet the requirement of fugitive emission class B as per ISO 15848 Part - 1 with test medium Methane or Helium.
495 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
6SP0P02
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T3 T3 T1 T1 T
3 T3 T3 T3 T1 T1 T
4 T3 T3 T3 T3 T1 T1 T
6 T3 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
496 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
9CK1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
SERVICE LIMITS
Size Range 0.5-12 0.5-12 0.5-12 0.5-12 0.5-12 0.5-12 0.5-12 14-16 14-16
Sch/WT Sch160 Sch160 XS XS Sch160 XS Sch120 Sch120 Sch120 Sch120 Sch120 20.62mm
Size 16
Sch/WT 23.83mm
497 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
9CK1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
498 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
9CK1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Pipe Nipple
499 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
9CK1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Sockolet 2 - 16 * 1/2 - 3/4 CL 6000 MSS SP-97 ASTM A182 GR F22 CL3 OLTS000097C
Sockolet 3 - 16 * 1 - 1.1/2 CL 3000 MSS SP-97 ASTM A182 GR F22 CL3 OLTS000096C
500 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
9CK1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Spectacle Blank 1/2 - 1.1/2 CL 1500 RTJ ASME B16.48 ASTM A387 GR 22 CL2 LBKB000347C 2
501 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
9CK1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
502 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
9CK1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
503 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
9CK1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
504 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
9CK1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
Notes
1: This pipe class is designed for full rating as per Group 1.10 of ASME B16.5 upto NPS 12. For NPS 14 and above, pipe class is designed for
line design condition as specified in SERVICE LIMITS table and Appendix 1 (Pipe Class Service Index).
2: The flange face finish of Ring Joint Type flanges shall be not exceed 63 micro-inches (1.6 micro-metres) Ra as per ASME B46.1, except
otherwise stated.
3: Dual Plate Check valves shall be used by default. Swing Check valves shall be used for dissimilar check valve scenario as required in
P&ID.
4: DELETED
5: DELETED
6: Minimum pipe size shall be NPS ¾ unless stated otherwise. Smaller sizes permitted for instrument connections and steam tracing etc., only
where specifically stated.
7: DELETED
8: For steam service, NPS 2 & larger Gate valve shall be Parallel slide gate valve with Cavity pressure relief system as per SAES-L-108,
Clause 7.12.
9: Gate Valves size NPS 1/2 - 1.1/2 with flanged end shall be used for mating flanges of equipment nozzles, instruments and for process
drain/vent.
10: DELETED
11: Straight lengths of small bore piping NPS 2” and smaller, shall be joined together by butt welding. Couplings shall not be used for this
purpose.
505 of 506
Pipe Class
PIPING MATERIAL SPECIFICATION
9CK1U01
Job No:JI-2032 Doc. No. D44-A-RE-585265 Rev. 00 Project: Fadhili
SYNOPSIS
1/2 T
RUN PIPE
3/4 T1 T
1 T1 T1 T
1.1/2 T1 T1 T1 T
2 T4 T4 T1 T1 T
3 T4 T4 T4 T1 T1 T
4 T4 T4 T4 T4 T1 T1 T
6 T4 T4 T4 T4 T3 T1 T1 T
8 T4 T4 T4 T4 T3 T3 T1 T1 T
10 T4 T4 T4 T4 T3 T3 T3 T1 T1 T
12 T4 T4 T4 T4 T3 T3 T3 T3 T1 T1 T
14 T4 T4 T4 T4 T3 T3 T3 T3 T3 T1 T1 T
16 T4 T4 T4 T4 T3 T3 T3 T3 T3 T3 T1 T1 T
ABBREVIATIONS:
506 of 506
EDSD REV
REVISION
REVISIONCERTIFICATION
CERTIFICATE VERIFICATION NO. DATE JO/EWO DESCRIPTION ENGG CERT PMT OPRNS
00
DATE:
DATE:
DATE:
DATE:
DATE:
THIS INDICATES THAT REV. NO.__________ BI-10-
TNP
LEAD
OF THIS DRAWING IS COVERED, FOR ALL B 04AUG16 01900-0004 RE-ISSUED FOR REVIEW RAG RSJ
RAG
CONTROL NUMBER
APPROVAL/CERTIFICATION REQUIREMENTS, 29SEPT16 BI-10-
/ RAG
RAG RSJ
ENGINEER
00 01900-0004 ISSUED FOR DESIGN
AGENCY
NLP / SSK
/ RD
BY:
PROJECT
BY DRAWING COMPLETION CERTIFICATE
ENGINEER
ENGINEER
PB / RSJ / KR
DISCIPLINE
CERTIFIED
29/09/2016
29/09/2016
29/09/2016
OPERATIONS
CONSTRUCTION
(DCC) NO. _____________________ DATE:
``
DOC
SAUDI ARABIA
D44
JO / EWO:
A
DWG.TYPE PLANT NO. INDEX
SAUDI ARABIAN OIL COMPANY
BI-10-01900-0004
DRAWING NO.
RE- 585265
64
64
OF
SHT. NO.
D44-A-RE-585265 Rev00.doc
00
REV. NO.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
H
O
LD
00
H
O
LD
00