Professional Documents
Culture Documents
MOLYKOTE® G-n Metal Assembly Spray is primarily designed as also be used wherever protection against friction and high load
a running-in lubricant for plain bearings, splines, gears, cams and conditions is needed, where burnishing is impractical, or where a
ways, and because of its low coefficient of friction, as a lubricant paste in aerosol form is desired. It is suitable for airframe and
for movable screws, threaded spindles and lead screws. It can aircraft engine applications.
Description Usable life and storage
MOLYKOTE® G-n Metal Assembly Paste is a multipurpose, When stored at 32°F to 104°F (0°C to 40°C), MOLYKOTE® G-n
heavy-duty lubricating paste containing a blend of molybdenum Metal Assembly Paste has a usable life of 60 months from date
disulfide and white solid lubricants in a mineral oil. It helps of manufacture. An oil layer may form on the product surface
prevent galling during run-in, helps extend the service life of during storage but may be readily mixed back in by stirring.
moving parts, and helps protect against fretting wear and
corrosion as well as welding of static joints. When stored at 32°F to 104°F (0°C to 40°C), MOLYKOTE® G-n
Metal Assembly Spray has a usable life of 24 months from date
MOLYKOTE® G-n Metal Assembly Spray is a high-performance of manufacture. Because it is an aerosol, punctures should be
paste in aerosol form. It is particularly effective as a running-in avoided, and containers should be kept away from heat, sparks
lubricant. This product features a low coefficient of friction and open flame.
immediately upon application, without burnishing.
Packaging
How to use These products are available in different standard container
MOLYKOTE® G-n Metal Assembly Paste can be applied in a thin sizes. Detailed container size information should be obtained
film to clean surfaces by either of the following methods: from your nearest MOLYKOTE® sales office or MOLYKOTE®
• Burnishing – Rub on with a clean, lint-free cloth. distributor.
• Brushing – Brush on, preferably using a brush with short, stiff
bristles.
Limitations
MOLYKOTE® G-n Metal Assembly Spray should be applied in a When used on threaded fasteners, mineral oil torquing
sweeping motion to obtain a thin, uniform coating. Avoid over- specifications should be reduced by one-third to avoid
application. No burnishing is required, and although best results overtightening. MOLYKOTE® G-n Metal Assembly Paste is not
are obtained on clean, dry surfaces, MOLYKOTE® G-n Metal recommended for use in pressure lines and grease guns.
Assembly Spray can also be applied on oily surfaces. The
lubricant’s solvent evaporates within 30 minutes. Shipping limitations
MOLYKOTE® G-n Metal Assembly Paste – None.
Handling precautions
PRODUCT SAFETY INFORMATION REQUIRED FOR SAFE MOLYKOTE® G-n Metal Assembly Spray – DOT Classification:
USE IS NOT INCLUDED IN THIS DOCUMENT. BEFORE Extremely flammable.
HANDLING, READ SAFETY DATA SHEETS AND CONTAINER
LABELS FOR SAFE USE, PHYSICAL AND HEALTH HAZARD
INFORMATION.
DuPont™, the DuPont Oval Logo, and all trademarks and service marks denoted with ™, ℠ or ® are owned by affiliates of DuPont de Nemours, Inc.
unless otherwise noted.
© 1997-2020 DuPont.
The information set forth herein is furnished free of charge and is based on technical data that DuPont believes to be reliable and falls within the normal
range of properties. It is intended for use by persons having technical skill, at their own discretion and risk. This data should not be used to establish
specification limits nor used alone as the basis of design. Handling precaution information is given with the understanding that those using it will satisfy
themselves that their particular conditions of use present no health or safety hazards. Since conditions of product use and disposal are outside our
control, we make no warranties, express or implied, and assume no liability in connection with any use of this information. As with any product,
evaluation under end use conditions prior to specification is essential. Nothing herein is to be taken as a license to operate or a recommendation to
infringe on patents.
Form No. 10-731F-01 (02/20) AGP16261