Professional Documents
Culture Documents
3
Chapter
Assembly Procedure
Please follow the information provided in this section to perform the complete
assembly procedure of the notebook. Be sure to use proper tools described before.
A
fter you have completed the previous chapter of complete disassembly, please follow this
chapter to assemble the notebook back together. This chapter describes the procedures of the
complete notebook assembly. In addition, in between procedures, the detailed assembly
procedure of individual modules will be provided for your service needs.
3-1
Assembly procedure
2. Install the CMOS fly cable on bottom case and secure 1 (M2*4L)screw.
M2*4L
3. Connect the bluetooth cable with bluetooth module and install it on bottom case
3-2
Assembly procedure
M O T H E R B O A R D Motherboard Module
M O D U L E The illustrations below show how to assemble and install the Motherboard module of the
notebook.
1. Insert the roboson minicard into its slot at 45°angles and press it down softly,and then
secure 2 (M2*3L) screws
2. Insert the TV tuner module into its slot at 45°angles and press it down softly,and then
secure 2 (M2*3L) screws and connect 1 antenna cable.
3-3
Assembly procedure
3. Install modem module on motherboard and secure 2 (M2*3L)screws, and then fix 1
pieces of tapes here, connect the modem cable with motherboard.
M2*3L
3-4
Assembly procedure
M2*3L
M2*6L
6. Connect the Bluetooth cable, CMOS fly cable and speaker cable with motherboard
and then fix 4 pieces of tapes here.
3-5
Assembly procedure
2. Secure 4(M2*4L) screws and connect the touchpad FPC with touchpad board.
3-6
Assembly procedure
M2*4L
3-7
Assembly procedure
M2*4L
M2*8L
M2*6L
M2*3L
M2*4L
M2*6L
3-8
Assembly procedure
LCD module
L C D M O D U L E
The illustrations below show how to assemble and install the LCD module of the notebook.
1. Install the WLAN antenna board on LCD back cover and arrange the antenna, then fix 2
pieces of tapes here.
2. Connect the camera cable with camera module and then install it on LCD back cover.
3-9
Assembly procedure
3. Arrange the microphone module on LCD back cover and pull it into LCD back cover with
tweezers, then fix 8 pieces of tapes here.
3 - 10
Assembly procedure
M2*3L
7. Arrange LCD panel on LCD back cover and install the bracket.
3 - 11
Assembly procedure
M2.5*6L
9. Connect inverter cable with inverter board and secure 2 (M2*3L)screws here.
3 - 12
Assembly procedure
M2*3L
11. Install the front bezel and press the edges softly to make it close.
3 - 13
Assembly procedure
13. Arrange WLAN antenna into bottom case and install LCD module on top case and.
3 - 14
Assembly procedure
14. Connect the coaxial cable and inverter cable with motherboard.
M2*8L
3 - 15
Assembly procedure
M2*6L
M2*6L
Keyboard Module
The illustrations below show how to install the keyboard module of the notebook.
3 - 16
Assembly procedure
1. Connect keyboard FPC with motherboard using tweezers and turn it onto top case.
1. Insert the optical drive module to its compartment and secure 1 (M2*6L) screw and the
rubber.
3 - 17
Assembly procedure
M2*6L
HDD module
H D D M O D U L E
A S S E M B L Y The illustrations below show how to assemble and install HDD Module of the notebook.
1. Lay the HDD module into its slot, and push it until it’s installed properly.
3 - 18
Assembly procedure
M2*6L
M E M O R Y
Memory Module
R E M O V E
The illustrations below show how to assemble and install Memory module of the notebook
Insert memory module at 45°angles and press down until it clicks into the latches.
3 - 19
Assembly procedure
W L A N
WLAN Module
R E M O V E
The illustrations below show how to assemble and install WLAN module of the notebook
Insert the WLAN module into its slot at 45°angles and press it down softly,and then secure
2 (M2*3L) screws and connect 3 antenna cables(black cable should be connected on main),
and paste 1 piece of tape here.
3 - 20
Assembly procedure
M2*3L
C P U I N S T A L L CPU Module
The illustration below shows how to install CPU and the heat sink of the notebook.
1. Use the CPU vacuum to “suck up” the CPU then Install the CPU and turn the
non-removable screw here 180 degrees clockwise to lock the CPU.
2. Install the CPU heat sink module gently and secure 3 (M2*4L) screws upon the CPU
module.
Note: If thermal module has no thermal pad on it, please plus a thermal pad on the
CPU die before assembling.
3 - 21
Assembly procedure
M2*4L
3. Install CPU fan and secure 3 (M2*6L) screws, and then connect fan cable.
M2*6L
3 - 22
Assembly procedure
M2*4L
3 - 23
Assembly procedure
B A T T E R Y Battery Module
M O D U L E
The illustrations below show how to install battery module of the notebook.
Slide on the battery module into its compartment and then lock the latch to fix it.
3 - 24