Professional Documents
Culture Documents
Description
Torque ‘n’ Tension 12 is a clear water based sealer for application on fasteners
in order to modify the torque tension properties. It is particularly suitable for use
on e-coat black, barrel lacquered surface following zinc/nickel electroplating.
Torque and Tension 12 is supplied as a ready to use low viscosity liquid that
can be applied by dip spin to limit thread fill problems and unwanted waste do to
dragout.
Table Of Sections
1. Physical properties
2. Operating standards
3. Solution make-up
4. Solution maintenance
5. Analytical control
6. Operating tips and equipment
7. Safety in Handling and Use
8. Waste Water treatment
9. Order information
1. Physical Properties
Physical Appearance White liquid
Flash Point > 190ºF (90ºC)
Solubility in water Complete
2. Operating Standards
Concentration 50-100% by volume
Temperature 68 – 86ºF (20 – 30ºC)
pH 8.0– 8.8
Dip time 20 - 40 seconds
Agitation Mechanical or barrel rotation
Filtration Recommended
3. Solution Make-Up
4. Solution Maintenance
As the Torque ‘n’ Tension 12 is applied onto dry articles, little maintenance of
the solution is necessary. Where necessary the solution level is maintained by
adding the Torque ‘n’ Tension 12 liquid.
Product consumption
Torque ‘n’ Tension 12 is usually consumed at a rate of 3 - 5 mls/ ft² of processed
surface area.
5. Analytical Control
pH
By pH-meter, (calibrated to pH 9.0 at 68oF (20° C))
Method
1. After the e-coat has been applied and baked, allow to cool to room
temperature before the Torque ‘n’ Tension 12 is used.
2. Immerse the basket in the Torque ‘n’ Tension 12 for 25 - 35 seconds and
drain in order to limit the loss of solution through dragout.
3. Dry the coated parts in the centrifugal dryer (it is preferable to have a slow
rotation speed -150 – 200 rpm. Temperature should be maintained between
140 – 175oF (60 - 80°C).
4. In all cases the parts should be tested under production conditions in order to
ascertain the correct operating conditions (i.e. drying temperature and rotation
speed).
5. To avoid unnecessary damage during this process a slow ramp up to final
speed of should be used.
6. The basket is approximately half filled for the process. Overfilling makes it
difficult to avoid thread fill and sticking together while very low loadings leads
to low coating thickness and unnecessary damage.
7. Generally it will be found that some parts have a greater tendency to trap
excess coating than others so it may be necessary to vary the above
parameters occasionally to maintain good results.
8. In use, the temperature of the working solution must now be allowed to fall
below 60oF (15oC). For storage, the solution must not be allowed to fall
below 40oF (5oC).
9. Order Information
Disclaimer
Also read carefully warning and safety information on the Material Safety Data Sheet. This data sheet contains
technical information required for safe and economical operation of this product. READ IT THOROUGHLY PRIOR TO
PRODUCT USE. Emergency directory assistance Chemtrec 1-800-424-9300.
DISCLAIMER: All statements, technical information and recommendations contained herein are based on tests we
believe to be reliable, but the accuracy or completeness thereof is not guaranteed. No statement or recommendation
shall constitute a representation unless set forth in an agreement signed by officers of seller and manufacturer. NO
WARRANTY OR MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE IS MADE. The
following warranty is made in lieu of such warranties and all other warranties, express, implied, or statutory.
Products are warranted to be free from defects in material and workmanship at the time sold. The sole obligation of
seller and manufacturer under this warranty shall be to replace any product defective at the time sold. Under no
circumstances shall manufacturer or seller be liable for any loss, damage or expense, direct or consequential, arising
out of the inability to use the product.
Notwithstanding the foregoing, if products are supplied in response to a customer request that specifies operating
parameters beyond those stated above, or if products are used under conditions exceeding said parameters, the
customer by acceptance or use thereof assumes all risk of product failure and of all direct, indirect and consequential
damages that may result from use of the products under conditions, and agrees to exonerate, indemnify and hold
harmless MacDermid Incorporated therefrom.
No suggestion for product use nor anything contained herein shall be construed as a recommendation to use any
product in infringement of any patent rights, and seller and manufacturer assume no responsibility or liability for any
such infringement.
187220
Version 1.0
June 06