Professional Documents
Culture Documents
Contents
1. Product features …………………………………………………………………………………………………………………………………………………….3
4. Product technical
parameters…………………………………………………………………………………………………………………………………10
5. Schematic
Diagram……………………………………………………………………………………………………………………………………………..11
2
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
1. Product features
Features:
1 Interlock between light and U.V. lamp
2 Delay and timing function on U.V. lamp
3 Light and sound hint
4 Appointment function on U.V. lamp
5 Pre cleaning function
7 Linkage function for fan-motor,light and U.V. lamp
HCB-1300V/H
V— vertical H—horizontal
H— Haier brand
3
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
4
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
5
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
6
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
7
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
8
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
9
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
10
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
External Dimension
mm 1780×792×1960 1370×620×1730 970×620×1730
(L×W ×H)
Inner Dimension mm
1710×550×750 1300×530×520 900×530×520
(L×W ×H)
5. Schematic Diagram
11
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
12
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
Key definition
A :This button is controlling the power of the machine。.hen pressing this button, the machine will turn on,
and related light will light. Press this button again,the machine will turn off.ang the light on the panel will go out.
E :Increase/Up;
13
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
F :Decrease/Down;
Method: Press ‘Adv.’for 5s,the display panel will show ‘t1’press or to change the parameters’s
14
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
name :t1-t2-t3-Pt-Ft-t1….when you choose the parameter you should press ‘Adv.’then use or to change
the value.Press ‘Adv.’for 5s,save &exit.
Time set
Choose parameter’t3’ to set the time.
Method: Press ‘Adv.’for 5s,the display panel will show ‘t1’press or to change the parameters’s
name :t1-t2-t3-Pt-Ft-t1….when you choose the parameter you should press ‘Adv.’then use or to change
the value.Press ‘Adv.’for 5s,save &exit.
UV Lamp Reservation
Choose parameter ‘Pt’ to set reservation time.
Method: Press ‘Adv.’for 5s,the display panel will show ‘t1’press or to change the parameters’s
name :t1-t2-t3-Pt-Ft-t1….when you choose the parameter you should press ‘Adv.’then use or to change
the value.Press ‘Adv.’for 5s,save &exit.
Lock function for ‘Adv.’ button
If there is no any button press in the 30 s, the system will back to the normal mode, the parameters will not be
stored.
FACTORY SETTING
Method: Press the adv. button and turn on the power at the same time, the LEDs will show’----’for 3 seconds the
system will back to the default sets, except t3.
UV Lamp control
The U.V light is normal closing status.
First of all, Close the door ,Press U.V button, the U.V lamp will be lighted after about10seconds, the delay time
belongs to t2 parameter. The sterilization time belongs to the t1 parameter.
Fluorescent Lamp control
The fluorescent lamp is normal closing status。When the U.V lamp goes out, you can press Light button to light the
fluorescent lamp.
Fan-motor control
After press power button,the fan motor is not working,the LEDs show ‘StOP’.
When the door is opening, Press Fan button, The fan motor will work after pretreatment stage; Press“∧”or“∨” to
adjust the speed of the fan. The fluorescent lamp will be lighted at the same time.
After closing the door, the fan motor will stop. The LEDs will show“STOP”.
Reservation function
One button for Reservation, At normal operation, press ‘Adv.’ to start reservation, pressing again will stop
reservation. If you want to change the reservation time,please press ‘Adv.’for at least 5 seconds,please see table 1,
parameter‘Pt’.
Speed Calibration for fan-motor
There are two potentiometers on the control board, rotate Potentiometer to adjust the speed of the airflow(RW2
(100K)-fine tuning、RW1(150K) :coarse tuning
Outlet
The outlet can be controlled by the PCB. You can press the button to make and break the power of the outlet.
15
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
Magnetic switch
Magnetic control switch provide a signal to the PCB board, and the PCB can control fan, fluorescent and ultraviolet
light;
When the door is closed,the magnetic switch will turn on,Fan and fluorescent will stop working,but the UV light
can be controlled by manual;
When the door is opened,the magnetic switch will turn off,the UV light will be put out.
16
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
17
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
18
LAMINAR FLOW CABINET HBC-900V/1300V/1600H -SERVICE MANUAL
Inspired living
Room 403D, Brand Building, Haier Industrial Park, No.1 Haier Road
Qingdao China
Website: www.haiermedical.com
19