Professional Documents
Culture Documents
page
Fire Suppression Systems أنظمة االطفاء الذات 2
*******************************
https://lnkd.in/eTvxmjw6 YouTube Channel لمتابعتنا على اليوتيوب
Download all PDF Lectures لتحميل جميع مذكرات الشرح لمواضيع ومحتوى القناة
https://lnkd.in/drCD_siJ
Page | 1
Eng. Khaled Mohsen
www.mcp-academy.com
Fire Suppression Systems أنظمة االطفاء الذات
تتحكم أنظمة اإلطفاء الذات ف الحرائق باستخدام المواد الكيميائية الجافة وثات أكسيد الكربون والغازات
وغازات اخرى حيث يتم تصميم كل من هذه األنظمةFM200 وNOVEC 1230 النظيفة مثل
.خصيصا لالستخدام ف خطر حريق معي ً واعتمادها
Fire suppression systems control fire using agents such as dry chemical, CO2, and
NOVEC, FM200 etc. Each of these systems must be specifically designed and
approved for use on a particular fire hazard.
فإنه يتحكم فpanel release control البمجة الخاصة بلوحة الكونبول الخاصة بالنظام تقوم ر
(والمتصلة بمجموعة من األسطوانات الت تحتويas solenoids, actuators, etc.) إطالق األجهزة
smoke عىل الغاز وذلك عند تنشيط أجهزة اإلنذار من خالل جهاز االستشعار الدخان االلكبونية
.حيث تقوم بتنشيط أجهزة التحكم وتحرير انطالق الغاز من األسطوانة وتفري غ غاز اإلطفاءdetectors
Page | 2
Eng. Khaled Mohsen
www.mcp-academy.com
تعريف غازات اإلطفاء النظيفة Clean Agent
ه غازات اطفاء حريق متطايرة أو غازية غب موصلة للكهرباء وال تبك بقايا عند التبخر وال تؤثر بالضر
عىل المواد او المعدات الت تقوم بحمايتها ف حالة حدوث الحريق.
غاز NOVEC 1230يشار إليه ب FK-5-1-12ف كود NFPA 2001وهو عبارة عن كيتون مفلور (أو
فلورو كيتون) ببكيبة كيميائية ل ( .CF3 CF2 C (O) CF (CF3) 2إنه سائل صاف ،عديم اللون ،ذو
رائحة منخفضة ،ذو ضغط فائق بالنيبوجي ويتم تخزينه ف أسطوانات عالية الضغط)
Page | 3
Eng. Khaled Mohsen
www.mcp-academy.com
NOVEC 1230
The NOVEC 1230 fire suppression system was designed as an alternative to
hydrofluorocarbon and a replacement for halon. It's stored as a liquid but
discharged as a non-toxic gas. Unlike other fire suppression systems that displace
oxygen or drown fires in water, the NOVEC 1230 clean agent system is a waterless
gas that interrupts a fire by absorbing the heat. This disruption quickly breaks the
chemical chain reaction that a fire needs to thrive. The NOVEC 1230 system is
electrically non-conductive, leaves no residue, and is safe for human occupancy.
NOVEC 1230 Fire Protection Fluid, referenced as FK-5- 1-12 in NFPA 2001, is a
fluorinated ketone (or fluoro ketone) with a chemical structure of CF3 CF2 C(O)
CF(CF3)2. It is a clear, colorless, low odor, liquid that is super-pressurized with
nitrogen and stored in high-pressure cylinders
إلطفاء الحريقFM200غاز
عبارة عن عامل نظيف إلطفاء الحرائق يهدف إىل العمل كبديل للهالون هو مركبFM-200 غاز
ً
يتم تضيفه كغاز عديم اللون وعديم الماء وغبHFC-227ea هيدروفلوروكربون معروف أيضا باسم
ً ً
معا أيضا لقطع من الكربون والفلور والهيدروجي والت تعملFM-200 تتكون أنظمة إخماد الحرائق.سام
التفاعل الكيميات المتسلسل للحريق وإزالة الحرارة الت توقف الحريق بعد ذلك قبل أن تتاح لها فرصة
ً
كهربائيا آمن لالستخدام ر
.البشي ً
هو أيضا غب موصلFM-200 نظام العامل النظيف.االنتشار
Page | 4
Eng. Khaled Mohsen
www.mcp-academy.com
FM-200
The FM-200 fire suppression system is clean agent fire suppression that's intended
to act as a halon alternative. It's a hydrofluorocarbon compound that's also known
as HFC-227ea. It's discharged as a, waterless, colorless, non-toxic gas. FM-200 fire
suppression systems are comprised of carbon, fluorine, and hydrogen which work
together to also interrupt a fire's chemical chain reaction and remove the heat
which then stops a fire before it ever has a chance to spread. The FM-200 clean
agent system is also electrically non-conductive and safe for human occupancy
حريق ف السوائل القابلة لالشتعال والسوائل القابلة لالشتعال والشحوم الببوليةClass B Fire
.والقطران والزيوت والدهانات الزيتية والمذيبات والورنيش والكحول والغازات القابلة لالشتعال
Classification fire
Class A Fire. A fire in ordinary combustible materials, such as wood, cloth, paper,
rubber, and many plastics.
Page | 5
Eng. Khaled Mohsen
www.mcp-academy.com
يستخدم كال النظامي بشكل عام ف نفس األنواع من المجاالت والصناعات مثل حيث يتم تطبيق نظام
اإلطفاء بالغازات النظيفة ف الغرف والمناطق ذات طبيعة خاصة تطلب الحفاظ عىل األجهزة او الوثائق
:الموجودة بالمكان دون خسائر ولذلك فيوجد الكثب من التطبيقات والت نذكر منها عىل سبيل المثال
مراكز البيانات وغرف تكنولوجيا المعلومات ومرافق االتصاالت وغرفة الكمبيوتر وغرف التحكم والمتاحف
والمختبات والمكتبات ومرافق الرعاية الصحية
ر وتخزين األرشيف التاريخ والمرافق الصيدالنية والطبية
. والتطبيقات البحرية،والتطبيقات العسكرية
Both systems are generally used in the same types of areas and industries like data
centers, IT rooms, Telecommunication facilities, Computer room, Control rooms,
Museums, Historical archive storage, Pharmaceutical and medical facilities,
laboratories, libraries, healthcare facilities, military applications, and marine
applications.
Both NOVEC 1230 and FM-200 are electrically non-conductive which allows
them to suppress fire while not disrupting machinery or electronics.
Page | 6
Eng. Khaled Mohsen
www.mcp-academy.com
طريقة تفعيل النظام وتشغيله إلطفاء الحريق
أوال :الطريقة األوتوماتيكية: -
طريقة عمل النظام عند حدوث الحريق يعمل كاشف الدخان عىل ارسال اشارة إىل لوحة التحكم والت
ر
الفالش( بعدها يعمل كاشف اخر عىل ارسال اشارة إىل تقوم بدورها عىل تشغيل اجهزة التنبيه) السارينة –
لوحة التحكم تأكيدا عىل وجود الحريق بعدها بعدة ثوات تقوم لوحة التحكم بإرسال إشارة إىل المشغل
الكهرت Electric actuatorلتفعيله حيث يعمل عىل تشغيل Cylinder Valveوالسماح للغاز للخروج ر
عب مواسب إىل مكان الحريق من خالل ال nozzles ليتدفق ر
ف بعض األنظمة يكون موجود أسطوانة نيبوجي صغبة Pilot Cylinderيتم فتحها عن طريق إشارة
كهربائية من النظام ليقوم الضغط الخارج منها بفتح األسطوانة الرئيس.
كهرت Pull Stationيعط لنظام التحكم إشارة الكتشاف أحد العاملي لحريق
ر من خالل تشغيل مفتاح
الكهرتSolenoid Valve.
ر وبالتاىل يعمل عىل إصدار أمر لتشغيل الصمام
كما توجد طريقة يدوية أخري وه طريقة ميكانيكية توجد عىل اسطوانة النيبوجي وتعمل عىل فتح
الكهرتSolenoid Valve
ر األسطوانة دون الحاجة لتشغيل الصمام
مالحظة :يجب ان ال تزيد المدة منذ بداية انطالق غاز االسطوانات وحت تواجد الغاز بكميته التصميمية
بالمكان المراد حمايته عن 10ثوات & وان يظل الغاز متواجد داخل الحب (الغرفة) لمدة 10دقائق بعد
انطالق الغاز من األسطوانات ولذلك فيجب التأكد من أغالق كامل فتحات الغرفة وغلق أنظمة سحب
الدخان والتكييف ( )MFSD-CLOSEDلحظة انطالق الغاز
تكون األسطوانات مناسبة إلعادة التعبئة وأن تكون مزودة بمجموعة صمام تفري غ ،وصمام أمان،
ر
ومؤش وتخفيف الضغط الزائد ،ومنفذ تعبئة ،ومقياس ضغط ،ومفتاح رإشاف للضغط المنخفض،
لمستوى السائل ،سعة تخزين الغاز النظيف.
Page | 7
Eng. Khaled Mohsen
www.mcp-academy.com
Containers shall be UL listed, FM approved and suitable for the liquid clean agent
to provide a quick and effective discharge in 10 seconds, or less. Each agent
storage container shall be suitable for refilling and shall be equipped with a
discharge valve assembly with fast acting rupture disc, safety plug, overpressure
relief, fill port, pressure gauge, low pressure supervisory switch and liquid level
indicator. Capacity of Clean Gas Agent storage. Include minimum working-
pressure rating that matches system charging pressure, valve, pressure switch, and
pressure gage.
،يجب مراعاة الحد األدت للضغوط التصميمية والت ستتحملها المكونات األخرى مثل الصمامات •
. ومقياس الضغط،ومفتاح الضغط
يجب ان تكون االسطوانة داخل المبت وغب معرضة للعوامل الجوية بحيث ال تتعرض ألشعة •
ر
المباشة و ف مكان سهل الوصول إليه للقيام بأعمال الفحص و الصيانة وعدم تركيب الشمس
األسطوانات ف مكان قد تتعرض فيه ألخطار حريق أو انفجار
.)تركيب األسطوانات بحيث يمكن إزالتها بسهولة إلعادة شحنها (التعبئة •
Page | 8
Eng. Khaled Mohsen
www.mcp-academy.com
• They must not be located where they will be exposed to a fire or explosion
in the hazard.
• The tanks should be installed so that they can be easily removed for
recharging.
• Tanks must be installed indoors. Do not install the tanks where they are
exposed to direct sunrays
Page | 9
Eng. Khaled Mohsen
www.mcp-academy.com
➢ Burst Disc Safety Relief
مفتاح أمان يعمل عىل تضيف الضغط الزائد من األسطوانة عند زيادة ضغط الغاز بداخلها ف حاالت
ارتفاع درجة الحرارة تجنبا لحدوث انفجار لألسطوانة
Safety Relief - Burst Disc A safety switch that works to discharge excess pressure
from the cylinder when the gas pressure inside it is increased in cases of high
temperature in order to avoid an explosion in the cylinder
مبي منسوب السائل ف األسطوانة يستخدم ف الكشف الدوري عىل محتوى األسطوانة حيث يكون
منسوب السائل ر
مؤشا لكمية السائل داحل األسطوانة
Page | 10
Eng. Khaled Mohsen
www.mcp-academy.com
the indicator of the level of the liquid in the cylinder is used in the periodic
inspection of the content of the cylinder, where the level of the liquid is an
indicator of the amount of liquid inside the cylinder
➢ Electric Actuator
يأخذ إشارة من لوحة التحكم للسماح للغاز بالمرور وقتSolenoid Valve كهرت هو عبارة عنر مشغل
.حدوث الحريق حيث يستخدم كوسيله اساسيه للتفعيل األوتوماتيك للنظام ومزود بجزء للتفعيل اليدوي
An electric actuator is a Solenoid Valve that takes a signal from the control panel
to allow gas to pass at the time of the fire. It is used as a primary means of
automatic activation of the system and is provided with a part for manual
activation.
Page | 11
Eng. Khaled Mohsen
www.mcp-academy.com
➢ Manual Control Head
.رأس التفعيل اليدوي يستخدم كوسيله يدويه للتفعيل
If there is more than one cylinder in the system, the cylinder shall be equipped
with a rubber gas discharge hose.
Page | 12
Eng. Khaled Mohsen
www.mcp-academy.com
➢ Distribution Piping
شبكة مواسب يجب أن تكون المواسب من مواد غب قابلة لالحباق و غب قابلة للصدأ و تتحمل ضغط
الغاز
➢ Discharge Nozzles
تعمل عىل توزي ع الغاز الخارج منها بالغرفة المطلوب حمايتها وتصنع من مواد مقاومة للصدأ و تتحمل
درجات الحرارة العالية لمقومة الحريق
Page | 13
Eng. Khaled Mohsen
www.mcp-academy.com
Discharge Nozzles work on distributing the gas out of it in the room to be
protected. They are made of rust-resistant materials and can withstand high
temperatures to resist fire.
➢ Pressure Gauge
تزود كل أسطوانة بعداد لبيات ضغط الغاز داخل األسطوانة كما تزود بمفتاح لمراقبة ضغط األسطوانة
Pressure Gauge Each cylinder is provided with a gauge for the gas pressure
gauges inside the cylinder and a switch for monitoring the cylinder pressure.
Pressure operating control head Pilot. Pressure operating control head the idea
of work depends on the presence of a piston that collects the pressure coming
from the nitrogen cylinder into a driving force that moves the activation head to
the operating position, after which the cylinder is unloaded.
Page | 14
Eng. Khaled Mohsen
www.mcp-academy.com
➢ Pressure Operated Switch
عن بدء عمليه اإلطفاء إىل نظام مكافحه الحريق علما بأنFeedback يستخدم كوسيله إلرسال معلومة
.عملية اإلطفاء من الممكن أن تبدأ بطريقه يدوية أو أوتوماتيكية
Page | 15
Eng. Khaled Mohsen
www.mcp-academy.com
الكهرت أو المشغل الذى يعمل
ر يوجد عىل كل أسطوانة والت تمكنك من تركيب المشغل اليدوي أو
.بالضغط ومزود بغطاء لحمايه األسطوانة أثناء عمليات النقل والبكيب
The cylinder head is located on each cylinder, which enables you to install the
manual, electric or pressure actuator and is equipped with a cover to protect the
cylinder during transportation and installation operations.
Page | 16
Eng. Khaled Mohsen
www.mcp-academy.com
System Detectors حساسات النظام
( حساسات الحريق والدخان واللهب والت تعمل عىل إعطاء إشارة إىلSmoke –Heat –Flame)
لوحة التحكم وقت حدوث الحريق ويختلف عددهم واختياراتهم حسب طبيعة وظروف المكان المراد
.حمايته
Heat, smoke and flame sensors, which work to give a signal to the control panel at
the time of the fire, and their number and choices vary according to the nature and
conditions of the place to be protected.
When applications for system design for 2 smoke detector sensors are installed, in
the case of smoke sensing by only one sensor, initiates the first alarm will start and
if the second sensor sensing smoke, the second alarm is confirmed by confirming
the occurrence of the fire and the start of activating the system to work after the
delay programming period to evacuate the place before the gas is released.
حساس2 ف غالب االستخدامات بالمبات وتطبيقات غرف االتصاالت او الكهرباء الصغبة يتم تركيب
دخان ويقوم الحساس االول ف حالة استشعار الدخان ببداء االنذار األول وف حالة استشعار الحساس
الثات الدخان يتم االنذار الثات بتأكيد حدوث الحريق وبداء تفعيل النظام للعمل بعد فبة التعطيل
. المؤقت ألخالء المكان قبل انطالق الغاز
فكرة التأكيد عىل حدوث الحريق باستخدام الحساس الثات ه حت ال يعمل النظام ف حالة االنذار
الخاط والذي قد ينتج من تعطل الحساس او استشعار أحد الحساسات للدخان من مصدر غب الحريق
.وبالتاىل عدم تشغيل النظام دون داع
Page | 17
Eng. Khaled Mohsen
www.mcp-academy.com
Control Panel لوحة التشغيل والتحكم
ر
تعمل عىل السماح للغاز بالخروج،الفالش تتصل بها مكونات النظام مثل الكواشف والجرس والشينة و
الكهرت وذلك عند حدوث الحريق
ر عن طريق إعطاء إشارة إىل مفتاح التشغيل
The components of the system such as detectors, bells, sirens and flashers are
connected to it and it’s work to allow the gas to release by giving a signal to the
solenoid actuator start switch when a fire occurs
Page | 18
Eng. Khaled Mohsen
www.mcp-academy.com
او تثبيت رSEMI-FLUSH MOUNTING )ويمكن تركيبها داخل الحائط (جزت
مباش عىل الجدار
SURFACE MOUNTING
Cabinets can either be surface-mounted directly to a wall or recessed into the wall
(semi-flush mounting).
SEMI-FLUSH MOUNTING
Semi-flush mounting involves recessing the cabinet into a wall and attaching it
directly to the wall’s studs. At a minimum, 1.5 inches of the cabinet must protrude
from the wall to allow for clearance of the panel door.
.✓ موقع تركيب اللوحة يكون جيد التهوية ونظيف وخال من الغبار
ر ن
.المباشة ✓ عدم تعرض اللوحة لمصادر الحرارة بما ف ذلك أشعة الشمس
االهتازات أو تعرض اللوحات ن
ن ً
.للضر ✓ يراىع ان يكون مكان التكيب بعيدا عن مصادر
ً
مثل محطة قاعدة جهاز اإلرسال،)RFI( ✓ التكيب بعيدا عن مصادر تداخل التددات الالسلكية
.واالستقبال الالسلك
ن
االهتازات القوية مثل مكيفات الهواء والمراوح الكبتة ✓ معزولة عن مصادر المعدات زات
Page | 19
Eng. Khaled Mohsen
www.mcp-academy.com
مفتاح التفعيل (تشغيل النظام) اليدوي Manual Release Switch
هو مفتاح يدوي يمكن من خالله تشغيل النظام بطريقة يدوية حالة مشاهدة الحريق وف هذه الحاله ال
يتم تفعيل النظام اوتوماتيك من خالل حساسات الدخان او الحرارة
MANUAL RELEASE SWITCH For systems intended clean agent release, a pre-
discharge must be configured to warn building of the impending discharge. The
setting of the release timer selects the duration of the pre-discharge signal.
قبل ان تتم عملية التفري غ للغاز يجب حدوث تحذير مسبق وتشغيل أجهزة إنذار الحريق (المسموعة
والمرئية) للتحذير قبل انطالق الغاز ويتم تحدد وبرمجة إعدادات المؤقت الخاص بمدة إشارة ما قبل
التفري غ وانطالق الغاز.
عند تنشيط مفتاح التشغيل اليدوي ،سيقوم النظام بتنشيط دوائر التحرير عند انتهاء مده االنتظار
والهدف من فبة االنتظار قبل انطالق الغاز هو التحذير ألخالء المكان قبل بداء عملية مكافحة الحريق
ف حالة ان المدة الزمنية لتشغيل النظام أتوماتيك عن طريق الحساسات ونظام الكونبول سوف يستغرق
اكب من المدة المطلوبة لتشغيل النظام عن طريق مفتاح التشغيل اليدوي ( manual releaseفبة وقت ر
تأخب أطالق الغاز) فسيتم تفعيل وأطالق الغاز بعد انتهاء مدة التأخب لإلنذار لمفتاح التشغيل اليدوي .
Upon activation of the Manual Release switch, the system will activate the
applicable releasing circuits when the Manual Release timer expires. The system
will also activate the applicable releasing circuits upon expiration of a previously
active automatic release timer, if the remaining time on the automatic release timer
is less than the programmed Manual Release timer.
Page | 20
Eng. Khaled Mohsen
www.mcp-academy.com
مفتاح تعطيل أنطالق الغاز Abort Switch
يستخدم إليقاف مؤقت النطالق الغاز ف حالة االنذار الخاط او السيطرة عىل الحريق وذلك باستمرار
الضغط علية حت يتم عمل restللوحة
ف خالل المدة من انطالق االنذار الثات وقبل انطالق الغاز من األسطوانة يتم تفعيل أمكانية استخدام
معطل األطالق Abort Switchف حالة عدم وجود حريق.
Abort switch definition as a system control that, when operated during the
releasing panel’s release delay countdown, extends the delay in accordance with a
predetermined. so, an operator can prevent the release of the suppression agent by
pressing the abort switch at any time between when the automatic releasing
sequence starts and the solenoid is activated.
ال يوجد وقت محدد لتعطيل تحرير الغاز طالما ان المستخدم مستمر بالضغط عىل المفتاح ولكن ف حالة
ف حالة ازالة الضغط عىل مفتاح تعطيل األطالق Abort Switchوتحرير الغاز قبل عمل restللوحة
الكونبول سيتم أطالق الغاز بعد 10ثوات.
الهدف من مدة 10ثوات لتشغيل النظام بعد تحرير الضغط عىل مفتاح Abort Switchان يسمح
بمغادرة الغرفة قبل انطالق الغاز
ف حالة الضغط عىل المفتاح بعد انطالق الغاز وتفري غ األسطوانات لن يتم توقف النظام
Page | 21
Eng. Khaled Mohsen
www.mcp-academy.com
No agent release occurs while the abort switch is held in.
- The abort switch has no effect on an activated releasing, pressing the switch will
not stop the release).
- the abort switch must be pressed and held before the second alarm (delay
timer finish) and activation occurs to prevent release.
• If the alarm conditions clear and a system reset occurs before the switch is
released, no agent release occurs.
• If the alarm conditions are not clear and the delay timer is still running, no
agent release occurs until the timer expires.
• If the alarm conditions are not clear and the delay timer has expired, agent
release occurs.
Notes: Manual release stations override the abort switch. In other words, if a
manual release station is activated while the abort switch is held in, agent release
occurs
Page | 22
Eng. Khaled Mohsen
www.mcp-academy.com
-تشغيل الحساس األول :إعطاء إشارة مرئية عىل لوحة التنبيه ،وتنشيط اإلنذار ،وأعطاء أشاره للوحة
تحكم الحريق الرئيسية للمبت إلغالق أنظمة تكييف الهواء والتهوية الت تخدم المنطقة المحمية ،وتحرير
األبواب المغلقة ف المنطقة المحمية وإرسال إشارة إىل نظام إنذار الحريق.
-تشغيل الحساس واالنذار الثا نت :إعطاء إشارة مرئية عىل لوحة التنبيه ،وتنشيط اإلنذار المسموع ،وبدء
عمل مؤقت التأخب الزمت لتفري غ األسطوانات من غاز اإلطفاء لمدة 30ثانية او 60ثانية حسب ما تم
برمجته بلوحة الكونبول ،وبعد انتهاء وقت التأخب يبدا الغاز بالتحرر من األسطوانات واالنطالق ألطفاء
الحريق.
مالحظة :يتم نف حالة االنذار ن
الثات أغالق أي نظام لسحب الدخان من الغرفة واغالق جميع الدنابر حت
يتمكن الغاز بعد األطالق بالتواجد داخل الغرفة لمده ال تقل عن 10دقائق.
-سوف يؤدي تفري غ غاز اإلطفاء إىل تشغيل إنذارات مسموعة ومرئية.
-ستعمل Manual Pull Stationالعاملة عىل تفري غ الغاز النظيف عند تنشيطها بتشغيل أنظمة
االنذار وتحرير الغاز بعد فبة تعطل لتشغيل االنذار السماح بأخالء المكان قبل انطالق الغاز
-ستؤدي مفاتيح Abort Switchإىل تأخب تحرير الغاز أثناء التنشيط والضغط علية بعد االنذار الثات،
ويجب عمل restللوحة الكونبول لمنع انطالق وتحرير الغاز حيث سيؤدي تحرير المفتاح وازالة
الضغط علية إىل تحرير الغاز واالنطالق بعد 10ثوات .
-يجب تثبيت المواسب والكيعان وجميع توصيالت شبكة المواسب والرشاشات NOZELجيدا Rigid
Supportلتتحمل الضغط التشغيىل للنظام.
-مده تفري غ غاز األسطوانات :يجب تصميم الغاز للتحرير وتفري غ األسطوانات ف غضون ٍ 10
ثوان أو
أقل.
-يجب أن يشتمل النظام عىل طاقة احتياطية طارئة emergency power supplyوالت توفر الطاقة
البديلة ف حالة انقطاع التيار الكهربات العادي من خالل مولدات أو وجود بطاريات طاقة للشحن داخل
اللوحات.
-ف حالة وجود معدات تعمل بالطاقة الكهربائية داخل الغرفة وطبيعة هذه المعدات قد تودي اىل حدوث
رشاراه او زيادة االشتعال والحريق فيجب أن يؤدي تفري غ الغاز ا إىل إلغاء وفصل الطاقة عن األجهزة داخل
الغرفة مع التنبيه عىل ان لوحات الكونبول للنظام يتم ربطها بمصدر طاقة بديل ف حالة انقطاع التيار
األساس.
مالحظة هامة :فبات ووقت التعطل للنظام Delay Timeقد تختلف عما سبق توضيحة حيث انه قد
يأخذ ف أعتبارات التشغيل تطبيقات االستخدام والمساحات وطبيعة المواد الموجودة بالغرفة المطلوب
حمايتها
Page | 23
Eng. Khaled Mohsen
www.mcp-academy.com
- Actuating first detector: Give visual indication on annunciator panel, energize
audible alarm, shut down air-condition and ventilating systems serving protected
area, release and closed doors in protected area and send signal to fire alarm
system.
- Operating abort switches will delay Clean Agent discharge while being
activated, and switches must be reset to prevent Clean Agent discharge. Release of
switch will discharge Clean Agent.
- Al tees, elbows and nozzle points should be clamped properly (piping shall be
install with rigid support)
Page | 24
Eng. Khaled Mohsen
www.mcp-academy.com
تحدد مدة التأخب بي تنشيط المفتاح وبداء انطالق الغاز من األسطوانة حت يتمكن الموجودين بالمكان
.لإلخالء قبل انطالق الغاز
.Automatic Release Delay Timer • الموقت التلقات بالنظام لتأخت تحرير وانطالق الغاز
ه المدة الزمنية من بداية تأكيد االنذار (وعمل االنذار الثات) وحت انطالق الغاز من األسطوانات وعند
يتم تنشيط األجهزة الخاصة بفتح وتحرير الغاز من داخل األسطوانة (عىل افباض أن،انتهاء المؤقت
.) غب نشطabort switch مفتاح التعطيل
البمجة سيتم
للوحة رrest ولم يتم عملabort switch عندما يتم ازالة الضغط وتحرير مفتاح التعطيل
ثوات حت يتمكن المتواجدون بالغرفة من الخروج قبل تفري غ الغاز بالغرفة10 انطالق الغاز بعد
DELAY TIMERS
the following three programmable timers
The Manual Release Time Delay is a programmable timer that specifies the delay
between the activation of a manual release switch and the activation of releasing
appliances. The default setting for this timer is 10 seconds. A setting of 0 causes
the releasing appliances to immediately activate after a manual release switch
activates.
The Automatic Release Time Delay is programmable timer that delays the
activation of the releasing appliance circuits. This timer starts immediately after
receiving a confirming alarm (cross-zoned system) or a first alarm (single alarm
system). When the timer expires, the releasing appliances activate (assuming the
abort switch is not active).
The Abort Release Time Delay specifies the action that occurs when the abort
switch is released. This option applies only to Agent Release and combination
Agent Release.
Page | 25
Eng. Khaled Mohsen
www.mcp-academy.com
Room Requirement متطلبات الغرفة
❖ غلق جميع المنافذ الموجودة بالجدران حول المواسب وتركيبات التكييف وغبه من الخدمات
fire stop sealant الت تمر داخل الغرفة باستخدام مواد مقاومة للحريق
Close all outlets in the walls around the pipes, air conditioning installations and
other services that pass inside the room using fire-resistant materials.
❖ التأكد من األغالق التام للفراغات من النوافذ واألبواب خاصة ف حالة تركيب أرضيات جاهزة
فيجب اغالق جميع منافذ وجدران وابواب الغرفة ب الكامل تحت االرضياتraised floor
Ensure that the voids from windows and doors are completely closed, especially in
the case of installing raised floors, all walls and doors of the room must be closed
Page | 26
Eng. Khaled Mohsen
www.mcp-academy.com
❖ تكون الحوائط واالبواب من النوع المقاوم للحريق والمعتمد كما أنه يجب تركيب وسائل االغالق
للتاكد من أغالق الغرفة أثناء تفعيل النظام وانطالق الغازDoor Holder الذات البواب الغرفة
The walls and doors shall be of the approved fire-resistant type and room door
holder is required to insure closing case in fire.
عىل جميع منافذ تركيبات التكييف او سحبMotorize Fire Smoke Damper ❖ تركيب
الدخان بالغرفة حت يتمكن النظام من اغالقها جميعا لعدم تشيب الغاز من الغرفة بعد االنطالق
Installing Motorize Fire Smoke Damper HVAC air Duct in the room so that the
system can close all of them to prevent gas leakage from the room after gas release
❖ التأكد من عدم وجود أي معوقات بالغرفة لمكان األسطوانات و لوحات الكونبول ومفاتيح التحكم
Ensure that there is no obstruction for cylinders, control panels and switches.
Page | 27
Eng. Khaled Mohsen
www.mcp-academy.com
System Operational Test and Inspection االختبارات وتشغيل النظام
➢ Installation Inspection فحص التكيبات
supervisor ✓ يجب التأكد من التثبيت الصحيح لألسطوانات والتوصيالت الخاصة براس األسطوانة مثل
باألسطواناتName Plate ومراجعه البيانات المكتوبة على شرط البيانpressure switch
✓ التأكد من ان أنواع مواد المواسير المستخدمة كما هو باالعتمادات الفنية بالمشروع وان تثبيت المواسير
installation detail يتوافق مع مخططات ال
التي يتم توصيلها مع مخرج األسطواناتFlex Connection ✓ التأكد من التوصيالت الخاصة ب
وقراءاه عداد الضغط
Ensure correct installation of cylinders and cylinder head connections such as supervisor
pressure switch and review the data written on the Name Plate of the cylinders
Ensure that the types of pipe materials used are as per the technical approvals of the
project and that the pipe installation is in accordance with the installation detail drawings.
Page | 28
Eng. Khaled Mohsen
www.mcp-academy.com
Verify the connections of the Flex Connection that are connected to the outlet of the
cylinders and read the pressure gauge
✓ التأكد من توزيع الرشاشات بالغرفة كما هو مطابق للمخططات المعتمدة وعدم وجود أي معوقات لعملها
وعلى نهايات تفريعات الرشاشات لتحمل ضغوط التشغيلFixed Support ✓ التثبيت الجيد للمواسير
Ensure that the sprinklers are distributed in the room in accordance with the approved
plan drawing and that there is no obstruction to their operation
Installation of Fixed Support pipes and at the ends of sprinkler branches to withstand the
operating pressures of the system
✓ التأكد من أغالق جميع الفتحات بين خطوط الصاج والمواسير او الكهرباء التي تخترق جدران الغرفة
Fire Stop Sealant باستخدام مواد مناسبة لمقاومة الحريق
على خطوط الصاج حتى يتم أغالقها الكترونيا حاله حدوث الحريق وقبل انطالقMFSD ✓ تركيب دنابر
الغاز
Page | 29
Eng. Khaled Mohsen
www.mcp-academy.com
Ensure that all openings between the duct lines, pipes or electrical cable trunk that
penetrate the walls of the room are closed using suitable materials to resist fire. Fire Stop
Sealant
Installing MFSD dampers on the duct so that they are closed by control in case of a fire
✓ التأكد من التركيبات والتوصيالت الكهربائية مثل أماكن لوحات الكهرباء وارتفاعات التركيب لكال
كما يجب عدم وجود أي معوقات الستخدامهاManual Release والAbort Switch من
✓ تركيب أجهزة اإلنذار المسموعة والمرئية وتركيب أبواب يمكن ان تقوم باإلغالق الذاتي باستخدام
مما يمنع ترك الباب مفتوح وأغالقه في حاله انطالق الغازDoor Holder
Ensure that the electrical installations and connections such as the locations of the
electrical panels and the installation heights for both the Abort Switch and the
Manual Release, and that there should be no obstacles to their use
Installing audible and visual alarms, and installing doors that can self-close using
the Door Holder, which prevents the door from being left open case in fire in the
event of a gas release
Page | 30
Eng. Khaled Mohsen
www.mcp-academy.com
➢ System operational tests اختبارات تشغيل النظام
✓ التأكد من فترات ومدة التأخير بالنظام حيث يتم تفعيل أجهزة اإلنذار من حساسات الدخان بالنظام
actuator وبداء اختبار أداء صمام التشغيل الكهربائي الذي يتم تركيبة على راس األسطوانة
والتأكد من عمل المشغل الكهربائيManual Release ✓ ثم يتم تفعيل النظام من خالل مفتاح ال
ألطالق الغازHold وانه يمكنه القيام بوظيفته وعملAbort Switch ✓ التأكد من فعالية مفتاح ال
للوحاتRest لعمل
Ensure the periods and duration of delays in the system, where the alarms are
activated from the smoke sensors in the system, and start testing the performance
of the electric operating valve that is installed on the actuator cylinder head.
Then the system is activated through the Manual Release Switch, making sure that
the electric actuator is working
Ensure the effectiveness of the Abort Switch and that it can do its job and hold to
release the gas to make rest for the control panel
Page | 31
Eng. Khaled Mohsen
www.mcp-academy.com
✓ يتم إعادة االختبارات مره أخرى على األسطوانات ال Reserveالموجودة بالنظام والتي يتم
تفعيلها من مفتاح خاص كما هو موضح بالصورة والهدف من األسطوانات التواجد كبديل عن
األسطوانات الرئيسية في حاله الصيانة او أعادة شحن األسطوانات في حاله عملها
The tests are repeated again on the Reserve cylinders in the system, which are
activated by a special key as shown in the picture. The aim of the cylinders is to be
a stand by for the main cylinders in the event of maintenance or to recharge the
cylinders in their working condition
Page | 32
Eng. Khaled Mohsen
www.mcp-academy.com
The devices shown in the picture are used to pressurized the room, obtain readings,
then release the room from depressurized room air, and compare the readings to
ensure that there are accepted reding for air leaks so that not to release gas outside
the room case of fire
Ensure that the system control panel is connected with the main building fire
control panel, which is programmed by the Sequences of operation through the
(cause and effect matrix) diagram drawing, which activate other systems such as
building alarms, access control release doors, elevator stops, stair pressure fans and
smoke exhaust fans. This programming is according to the systems in the building
and the operating conditions according to the nature of the building and the
evacuation plan.
Page | 33
Eng. Khaled Mohsen
www.mcp-academy.com
References from NFPA 2001 Clean Agent Fire Extinguishing Systems
➢ Fire Classification and Clean Agent Definition
Page | 34
Eng. Khaled Mohsen
www.mcp-academy.com
➢ Clean agent requirement for minimum design quantity
Page | 35
Eng. Khaled Mohsen
www.mcp-academy.com
➢ Piping System fittings design requirement
Page | 36
Eng. Khaled Mohsen
www.mcp-academy.com
➢ Storage cylinder location
➢ Leakage Control
Page | 37
Eng. Khaled Mohsen
www.mcp-academy.com
➢ Room Requirement for wall and under raised floor closing
Page | 38
Eng. Khaled Mohsen
www.mcp-academy.com
➢ Power Requirement
Page | 39
Eng. Khaled Mohsen
www.mcp-academy.com
➢ Abort Switch Predetermined
Page | 40
Eng. Khaled Mohsen
www.mcp-academy.com
➢ Abort Switch Installation
Page | 41
Eng. Khaled Mohsen
www.mcp-academy.com
Contact Us
+201020414881
info@mcp-academy.com
WWW.MCP-ACADEMY.COM
follow us