Professional Documents
Culture Documents
Type D
Series
mechanical diaphragm
Versatility
Different diaphragm sizes are available to
- The dosed liquid contains small
amounts of suspended solids
- The dosed liquid is a toxic solution
- A drip proof/air tight application is
required
CODE 11 - S.S.316 VERSION
Reliability
The use of quality materials along with a
reduction system and is available with
either a NEMA 56C motor flange (with
or without motor) and is also available
with an IEC B14 electric motor that meets
UNEL-MEC specifications.
high degree of accuracy and repeatability
assures maximum reliability for the The motor power range is from 1/4 HP to
mechanical diaphragm SR series. 1/2 HP and for IEC motors from 0.18 Kw
up to 0.37 Kw. There are many options
The best performance for each application The gearbox is a standard wormwheel
is achieved through optimal selection of reduction system with all bearings
pump materials and diaphragm design. supported within a fully lubricated
gearbox.
GENERAL DIMENSIONS IN mm
A 57 57 68 68
B 90 90 100 100
C 70 70 65 65
D 75 75 73 73
E
F 90 90 90 90 H
G 75 75 75 75 I
I 65 65 65 65
G
F
O
D
L 7 7 7 7
O 80 80 78 78 A B C N
These are general dimensions and indicative of the maximum acceptable pump dimensions
SR Series
Type D 050U
TECHNICAL GUIDE
Reduction ratio (*1) Capacity (*2) Max Press. PSI Diaphrag.
Stroke
Connections Ø
Pump type SPM GPM GPH PSI Motor Lenght
(*3) (mm)
(mm)
60 Hz 60 Hz 60 Hz SS 316 PVC
I 42 0,0211 1,27
F 70 0,0369 2,22 1/4 HP
D-050U-30 203 145 NEMA 30
C 116 0,0607 3,64 56C
B 139 0,0738 4,43 1/2” or
5
I 42 0,0738 4,43 NPT
0,18kW
F 70 0,1268 7,60 for
D-050U-50 145 IEC 50
C 116 0,2166 13,00 motor
B 139 0,2586 15,53
(*1) Strokes per minute designation code with 4 poles motor (1725 rpm)
I = Reduction ratio 1 : 40 = 42 strokes at 60 Hz
F = Reduction ratio 1 : 24 = 70 strokes at 60 Hz
C = Reduction ratio 1 : 14,5 = 116 strokes at 60 Hz
B = Reduction ratio 1 : 12 = 139 strokes at 60 Hz
(*2) The capacity is subject to change due to working pressure, dosed liquid, viscosity and piping dimensions.
(*3) Different types and sizes of connections are available upon request
(4) The pumps can be supplied with accessories if requested.
(5) The pumps are epoxy coated RAL 7030
Mechanical Diaphragm
Dosing Pumps
Type D 100U
TECHNICAL GUIDE
Reduction Ratio (*1) Capacity (*2)
Max Press. PSI Connections (*3) Diaphrag. Stroke
Pump type SPM GPM GPH Motor Ø Lenght
(mm) (mm)
60 Hz 60 Hz 60 Hz SS 316 PVC SS 316 PVC
I 42 0,24 14,27
F 70 0,40 23,78
D-100U-70 72 1/2” NPT 70
C 116 0,66 39,63
B 139 0,79 47,56
I 42 0,36 21,66
F 70 0,61 36,46 1/4 HP
D-100U-90 43 NEMA 90
C 116 1,01 60,77 56C
B 139 1,22 72,91 or
3/4” NPT 10
I 42 0,49 29,59
0,18kW
F 70 0,82 49,41 for
D-100U-105 IEC 105
C 116 1,31 78,73 motor
B 139 1,57 94,48
22
I 42 0,56 33,55
F 70 0,93 56,01
D-100U-120 1” NPT 120
C 116 1,65 98,81
B 139 1,98 118,57
(*1) Strokes per minute designation code with 4 poles motor (1725 rpm)
I = Reduction ratio 1 : 40 = 42 strokes at 60 Hz
F = Reduction ratio 1 : 24 = 70 strokes at 60 Hz
C = Reduction ratio 1 : 14,5 = 116 strokes at 60 Hz
B = Reduction ratio 1 : 12 = 139 strokes at 60 Hz
(*2) The capacity is subject to change due to working pressure, dosed liquid, viscosity and piping dimensions.
(*3) Different types and sizes of connections are available upon request
(4) The pumps can be supplied with accessories if requested.
(5) The pumps are epoxy coated RAL 7030
SR Series
Type D 101U
and D 121U
TECHNICAL GUIDE
Reduction Ratio (*1) Capacity (*2)
Max Press. PSI Connections (*3) Diaphrag. Stroke
Pump type SPM GPM GPH Motor Ø Lenght
(mm) (mm)
60 Hz 60 Hz 60 Hz SS 316 PVC SS 316 PVC
F 84 0,48 28,53
D-101U-70 C 116 0,66 39,00 116 1/2” NPT 70
B 144 0,81 48,72
F 84 0,78 46,92 1/3 HP
NEMA
D-101U-90 C 116 1,01 64,04 72 56C 90
B 144 1,35 80,85
or
3/4” NPT 10
F 84 1,06 63,73
0,25kW
D-101U-105 C 116 1,31 87,19 for 105
IEC
B 144 1,75 104,94 motor
43
F 84 1,19 71,33
D-101U-120 C 116 1,65 97,65 1” NPT 120
B 144 2,16 129,35
F 84 1,70 102,09
1/2 HP
D-121U-120 C 116 2,31 138,86 43 1” NPT NEMA 120 12,5
56C
B 144 3,03 181,98
(*1) Strokes per minute designation code with 4 poles motor (1725 rpm)
I = Reduction ratio 1 : 40 = 42 strokes at 60 Hz
F = Reduction ratio 1 : 20 = 84 strokes at 60 Hz
C = Reduction ratio 1 : 14.5 = 116 strokes at 60 Hz
B = Reduction ratio 1 : 11.5 = 144 strokes at 60 Hz
(*2) The capacity is subject to change due to working pressure, dosed liquid, viscosity and piping dimensions.
(*3) Different types and sizes of connections are available upon request
(4) The pumps can be supplied with accessories if requested.
(5) The pumps are epoxy coated RAL 7030
Mechanical Diaphragm
Dosing Pumps
Typical Installation
SAFETY VALVES
PULSATION
BACK PRESSURE
DAMPENERS
VALVES
FILTERS
Each metering pump can be supplied with accessories 4.- PULSATION DAMPENER
to enhance the performance and accuracy of the Metering pumps have a pulsating flow.
dosing pump system. Both spring return plunger dosing pumps and quick
These accessories will assure : closing valves start and stop fluids that are in motion.
- Increased efficiency and increased pump life Spring return plunger dosing pumps derive their
- Decreased maintenance and operational costs pumping action by capturing a given amount of fluid in
a chamber and pushing it out of the pump’s discharge
Controlling fluid dynamics is essential to ensure efficient valve.
and safe use of the process system. Uncontrolled fluid
in motion can physically destroy a pumping system Each pump cycle also includes a suction stroke during
which includes pump, valves, flow meters, back which the discharge fluid flow is stopped.
pressure valves, inline instrumentation and piping. This pumping action produces an acceleration/
deceleration of the fluid, creating units of uncontrolled
1.- FILTERS energy resulting in pulsations observed as pressure
We suggest installing filters on the suction side piping spikes.
to prevent problems that can be caused by welding
particles, seal fragments or impurities in the liquid. Pulsation dampeners are required for two reasons:
The use of filters assures trouble-free dosing. - To reduce high, non-permissible pressure fluctuations.
- To create a nearly smooth and continuous flow.
2.- PRESSURE RELIEF VALVES
Pressure relief valves are designed to protect the pump 5.- CALIBRATION CYLINDERS
and chemical feed system from over pressure damage Calibration Cylinders allow visual confirmation of the
caused by defective equipment or a blockage in the pumps flow rate.
chemical feed line.
Pulsation dampeners
Type: HSTX
Body in 316 S.S. composed of a
two part assembly utilizing a special
housing that under dynamic pressure
tends to seal itself.
Bladders are compatible with the
liquids used. Built in accordance with
ASME VIII° Div. 1 rules.
Type: HSTPVC
Body in PVC composed of a two part
assembly utilizing a special hosing
that under hydraulic pressure tends to
seal itself.
Maximum temperature: + 122 °F.
Bladders are chemically compatible
with process liquids.
Relief valves
Polyethylene tanks
Metering pumps can be mounted on
tank tops
Our product line also includes the following:
SR series:
Hydraulic diaphragm dosing pumps, type “B”, “BR” and “SD”
Mechanical diaphragm dosing pumps, type “FM”
Plunger dosing pumps, type “A”
SDP series:
Solenoid dosing pumps, type “S”
Solenoid dosing pumps type “GA”
H series:
Automatic plants for dissolution and preparation of powdered polyelectrolytes, type “HA” and “HB”
EM series:
Electric mixers for chemical mixing, type “DMT”, “DEM”, “DRV” and “DRC”