Professional Documents
Culture Documents
Warning Chime System: Section
Warning Chime System: Section
WCS
A
B
SECTION
WARNING CHIME SYSTEM C
E
CONTENTS
HOW TO USE THIS MANUAL ...................... 3 PARKING BRAKE RELEASE WARNING CHIME ..... 9 F
PARKING BRAKE RELEASE WARNING CHIME
APPLICATION NOTICE ...................................... 3 : System Diagram ..................................................... 9
Information ................................................................ 3 PARKING BRAKE RELEASE WARNING CHIME G
: System Description ................................................. 9
PRECAUTION ............................................... 4
DIAGNOSIS SYSTEM (COMBINATION
PRECAUTIONS ................................................... 4 METER) ............................................................. 10 H
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- TYPE A .......................................................................10
SIONER" ................................................................... 4 TYPE A : Diagnosis Description ..............................10 I
TYPE A : CONSULT Function .................................11
SYSTEM DESCRIPTION .............................. 5
TYPE B .......................................................................13
COMPONENT PARTS ........................................ 5 TYPE B : Diagnosis Description ..............................13 J
Component Parts Location ........................................ 5 TYPE B : CONSULT Function .................................14
Component Description ............................................. 5
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI-
SYSTEM .............................................................. 7 K
GENT KEY SYSTEM) ....................................... 18
WARNING CHIME SYSTEM ....................................... 7 COMMON ITEM .........................................................18
WARNING CHIME SYSTEM : System Diagram ...... 7 COMMON ITEM : CONSULT Function (BCM - L
WARNING CHIME SYSTEM : System Description COMMON ITEM) .....................................................18
...... 7
BUZZER .....................................................................19
LIGHT REMINDER WARNING CHIME ....................... 7 BUZZER : CONSULT Function (BCM - BUZZER)....19 M
LIGHT REMINDER WARNING CHIME : System
Diagram ..................................................................... 7 DIAGNOSIS SYSTEM (BCM) (WITHOUT IN-
LIGHT REMINDER WARNING CHIME : System TELLIGENT KEY SYSTEM) ............................. 20 WCS
Description ................................................................ 7
COMMON ITEM .........................................................20
SEAT BELT WARNING CHIME .................................. 8 COMMON ITEM : CONSULT Function (BCM -
SEAT BELT WARNING CHIME : System Diagram COMMON ITEM) .....................................................20 O
...... 8
SEAT BELT WARNING CHIME : System Descrip- BUZZER .....................................................................21
tion ............................................................................ 8 BUZZER : CONSULT Function (BCM - BUZZER)....21
P
KEY WARNING CHIME (WITHOUT INTELLIGENT ECU DIAGNOSIS INFORMATION .............. 22
KEY) ............................................................................. 8
KEY WARNING CHIME (WITHOUT INTELLI-
BCM, COMBINATION METER ......................... 22
List of ECU Reference .............................................22
GENT KEY) : System Diagram ................................. 8
KEY WARNING CHIME (WITHOUT INTELLI- WIRING DIAGRAM ...................................... 23
GENT KEY) : System Description ............................. 8
TYPE A
E
F
JSNIA3946ZZ
H
TYPE B
JSNIA3947ZZ
WCS
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
ALNIA1292ZZ
WCS
1. Combination meter 2. Combination switch (lighting and turn 3. Key switch
signal switch)
4. Seat belt buckle switch LH 5. Front door switch LH 6. BCM (view with instrument panel re-
moved)
O
7. ABS actuator and electric unit (control 8. Parking brake switch (view with con-
unit) sole removed)
P
Component Description INFOID:0000000009269275
F
AWNIA2359GB
G
WARNING CHIME SYSTEM : System Description INFOID:0000000009269277
DESCRIPTION
H
• The buzzer for warning chime system is installed in the combination meter.
• The buzzer sounds when the combination meter receives a buzzer output signal from the BCM.
• The BCM receives signals from various units and transmits a buzzer output signal to the combination meter
with CAN communication line if it judges that the warning buzzer should be activated. I
LIGHT REMINDER WARNING CHIME
LIGHT REMINDER WARNING CHIME : System Diagram INFOID:0000000009269278 J
ALNIA1293GB
M
WCS
DESCRIPTION
With ignition switch in OFF or ACC position, driver door open, and lighting switch in 1st or 2nd position, the
light warning chime will sound. O
• BCM detects ignition switch in OFF or ACC position, front door switch LH ON, and lighting switch in 1st or
2nd position, and then transmits buzzer output signal (light reminder warning chime) to combination meter
with CAN communication line.
• When combination meter receives buzzer output signal (light reminder warning chime), it sounds the buzzer. P
AWNIA2390GB
DESCRIPTION
With ignition switch turned ON and driver seat belt unfastened, seat belt warning chime will sound for approxi-
mately 6 seconds.
• BCM receives seat belt buckle switch signal from combination meter with CAN communication line.
• BCM detects ignition switch turned ON and seat belt buckle switch LH ON, and then transmits buzzer output
signal (seat belt warning chime) to combination meter with CAN communication line.
• When combination meter receives buzzer output signal (seat belt warning chime), it sounds the buzzer.
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled
• Ignition switch OFF→ON
• Seat belt buckle switch LH is ON (driver seat belt not fastened)
WARNING CANCEL CONDITIONS
Cancels the warning if any of the following conditions is fulfilled.
• Ignition switch OFF
• Seat belt buckle switch LH is OFF (driver seat belt fastened)
KEY WARNING CHIME (WITHOUT INTELLIGENT KEY)
KEY WARNING CHIME (WITHOUT INTELLIGENT KEY) : System Diagram
INFOID:0000000009269282
AWNIA2361GB
With the key inserted into the key switch, and the ignition switch in the OFF or ACC position, when driver's
door is opened, the warning chime will sound.
Revision: April 2013 WCS-8 2014 Versa Sedan
SYSTEM
< SYSTEM DESCRIPTION >
• BCM detects key inserted into the ignition switch, and sends key warning signal to combination meter with
CAN communication line. A
• When combination meter receives key warning signal, it sounds warning chime.
PARKING BRAKE RELEASE WARNING CHIME
B
PARKING BRAKE RELEASE WARNING CHIME : System Diagram INFOID:0000000009269284
E
AWNIA0263GB
DESCRIPTION
• The combination meter receives the vehicle speed signal from the ABS actuator and electric unit (control G
unit) via CAN communication line.
• The combination meter judges whether the parking brake is released using the parking brake switch signal
from the parking brake switch, and sounds the warning buzzer if necessary.
H
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled:
• Vehicle speed is approximately 7 km/h (4.3 MPH) or higher I
• Parking brake switch ON
WARNING CANCEL CONDITIONS
J
Warning is canceled if any of the following conditions are fulfilled:
• Vehicle speed is approximately 3 km/h (1.9 MPH) or less
• Parking brake switch OFF
K
WCS
NOTE:
• Check combination meter power supply and ground circuits if self-diagnosis mode does not start. Refer to
MWI-94, "COMBINATION METER : Diagnosis Procedure". Replace combination meter if power supply and
ground circuits are found to be normal and self-diagnosis mode does not start. Refer to MWI-104, "Removal
and Installation".
• Combination meter self-diagnosis mode will function with the ignition switch in ON. Combination meter self-
diagnosis mode will exit upon turning the ignition switch to OFF.
METHOD OF STARTING
1. Turn the ignition switch OFF.
2. Turn the ignition switch ON while pressing and holding the
switch (1) for 0.8 seconds or more.
JSNIA3917ZZ
3. Press the switch at least 3 times. (Within 7 seconds after the ignition switch is turned ON.)
4. The combination meter is turned to self-diagnosis mode.
• All segments of the information display are displayed.
JSNIA3891ZZ
JSNIA3903ZZ F
NOTE:
• If any of the meters or gauges is not activated, replace combination meter.
• The figure is reference. G
TYPE A : CONSULT Function INFOID:0000000009507071
APPLICATION ITEMS H
CONSULT can display each diagnostic item using the diagnostic test modes shown.
MAIN M
Display item [Unit] Description
SIGNALS
SPEED METER
X Displays the value of vehicle speed signal.
[km/h] or [mph] WCS
SPEED OUTPUT Displays the value of vehicle speed signal, which is transmitted to each unit with
X
[km/h] or [mph] CAN communication.
ODO OUTPUT Displays odometer signal value transmitted to other units via CAN communica- O
[km/h or mph] tion.
TACHO METER
X Displays the value of engine speed signal, which is input from ECM.
[rpm] P
FUEL METER
X Displays the fuel level.
[L]
W TEMP METER
X Displays the value of engine coolant temperature signal, which is input from ECM.
[°C] or [°F]
ABS W/L
Displays [ON/OFF] condition of ABS warning indicator
[ON/OFF]
W/L ON HISTORY C
• Stores histories when warning/indicator lamp is turned on.
• “W/L ON HISTORY” indicates the “TIME” when the warning/ indicator lamp is turned on.
• The “TIME” above is: D
- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine
and waiting for 30 seconds.
- 1 - 39: The number of times the engine was restarted after the 0 condition. E
- NO W/L ON HISTORY: Stores NO (0) turning on history of warning/indicator lamp.
NOTE:
• W/L ON HISTORY is not stored for approximately 30 seconds after the engine starts.
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets F
low.
Display Item
G
Display item Description
ABS W/L Lighting history of ABS warning lamp.
H
VDC/TCS IND Lighting history of VDC warning lamp.
SLIP IND Lighting history of SLIP warning lamp.
BRAKE W/L Lighting history of brake warning lamp. I
OIL W/L Lighting history of oil pressure warning lamp.
C-ENG W/L Lighting history of malfunction indicator lamp (MIL).
J
AIR PRES W/L Lighting history of tire pressure warning lamp.
EPS W/L Lighting history of EPS warning lamp.
CHAGE W/L Lighting history of charging warning lamp. K
DOOR W/L Lighting history of door warning lamp.
CRUISE W/L Lighting history of cruise warning lamp.
O/D OFF IND Lighting history of O/D OFF indicator lamp. L
FUEL W/L Lighting history of fuel warning lamp.
WASHER W/L Lighting history of washer warning lamp.
M
TYPE B
TYPE B : Diagnosis Description INFOID:0000000009507072
WCS
JSNIA3904ZZ
JSNIA3900ZZ
AWNIA2440ZZ
NOTE:
• If any of the meters or gauges is not activated, replace combination meter.
• The figure is reference.
TYPE B : CONSULT Function INFOID:0000000009507073
APPLICATION ITEMS
CONSULT can display each diagnostic item using the diagnostic test modes shown.
MAIN
Display item [Unit] Description
SIGNALS C
SPEED METER
X Displays the value of vehicle speed signal.
[km/h] or [mph]
SPEED OUTPUT
X
Displays the value of vehicle speed signal, which is transmitted to each unit with D
[km/h] or [mph] CAN communication.
ODO OUTPUT Displays odometer signal value transmitted to other units via CAN communica-
[km/h or mph] tion. E
TACHO METER
X Displays the value of engine speed signal, which is input from ECM.
[rpm]
FUEL METER F
X Displays the fuel level.
[L]
W TEMP METER
X Displays the value of engine coolant temperature signal, which is input from ECM.
[°C] or [°F]
G
ABS W/L
Displays [ON/OFF] condition of ABS warning indicator
[ON/OFF]
BRAKE W/L H
Displays [ON/OFF] condition of brake warning indicator.
[ON/OFF]
DOOR W/L
Displays [ON/OFF] condition of door warning indicator.
[ON/OFF]
I
HI-BEAM IND
Displays [ON/OFF] condition of high beam indicator.
[ON/OFF]
TURN IND
Displays [ON/OFF] condition of turn indicator. J
[ON/OFF]
LIGHT IND
Displays [ON/OFF] condition of light indicator.
[ON/OFF]
K
OIL W/L
Displays [ON/OFF] condition of oil pressure warning indicator.
[ON/OFF]
MIL
[ON/OFF]
Displays [ON/OFF] condition of malfunction indicator. L
CRUISE IND
Displays [ON/OFF] condition of CRUISE indicator.
[Off]
M
O/D OFF IND
Displays [ON/OFF] condition of O/D OFF indicator.
[ON/OFF]
FUEL W/L
Displays [ON/OFF] condition of low-fuel warning indicator. WCS
[ON/OFF]
KEY G/Y W/L
Displays [ON/OFF] condition of key warning lamp.
[ON/OFF]
O/D OFF SW O
Displays [ON/OFF] condition of O/D OFF switch.
[ON/OFF]
REAR DEF SW
Displays [ON/OFF] condition of rear window defogger switch.
[ON/OFF] P
BRAKE SW
Displays [ON/OFF] condition of brake switch.
[ON/OFF]
EPS W/L
Displays [ON/OFF] condition of EPS indicator.
[ON/OFF]
CHAGE W/L
Displays [ON/OFF] condition of charge warning indicator.
[Off]
SPECIAL FUNCTION
Special menu
W/L ON HISTORY
• Stores histories when warning/indicator lamp is turned on.
• “W/L ON HISTORY” indicates the “TIME” when the warning/ indicator lamp is turned on.
• The “TIME” above is:
- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine
and waiting for 30 seconds.
- 1 - 39: The number of times the engine was restarted after the 0 condition.
- NO W/L ON HISTORY: Stores NO (0) turning on history of warning/indicator lamp.
NOTE:
• W/L ON HISTORY is not stored for approximately 30 seconds after the engine starts.
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets
low.
Display Item
WCS
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
Configuration
Work support
Data Monitor
Active Test
DATA MONITOR B
WCS
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
Configuration
Work support
Data Monitor
Active Test
DATA MONITOR B
WCS
ECU Reference
BCS-28, "Reference Value"
WCS
ABNWA1783GB
ABNIA4585GB
WCS
ABNIA4567GB
ABNIA4568GB
WCS
ABNIA4586GB
ABNIA4587GB
OVERALL SEQUENCE
C
AWNIA2375GB M
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM WCS
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
O
>> GO TO 2.
2.CHECK SYMPTOM P
• Check the symptom based on the information obtained from the customer.
• Check if any other malfunctions are present.
>> GO TO 3.
3.CHECK CONSULT SELF-DIAGNOSIS RESULTS
>> GO TO 5.
5.REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts.
NOTE:
If DTC is displayed, erase DTC after repairing or replacing malfunctioning parts.
>> GO TO 6.
6.FINAL CHECK
Check that the warning buzzer in the combination meter operates normally.
Does it operate normally?
YES >> Inspection End.
NO >> GO TO 1.
C
Regarding Wiring Diagram information, refer to MWI-77, "Wiring Diagram".
1.CHECK FUSE D
Terminals
(+) (−) Voltage J
Ignition switch position
Combination meter (Approx.)
Connector Terminal
ON K
1 Ground Battery voltage
OFF
M24
3 ON Battery voltage
L
OFF 0
Is the inspection result normal?
YES >> GO TO 3. M
NO >> Check harness between combination meter and fuse.
3.CHECK GROUND CIRCUIT
WCS
1. Turn ignition switch OFF.
2. Check continuity between combination meter harness connector M24 terminals 21, 22, 23 and ground.
O
Combination meter
Continuity
Connector Terminal
21 Ground P
M24 22 Yes
23
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
COMBINATION METER (TYPE B)
Revision: April 2013 WCS-31 2014 Versa Sedan
POWER SUPPLY AND GROUND CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
COMBINATION METER (TYPE B) : Diagnosis Procedure INFOID:0000000009507658
1.CHECK FUSE
Check for blown combination meter fuses.
Terminals
(+) Continuity
(–)
Connector Terminal
21
M82 22 Ground Yes
23
Is the inspection result normal?
YES >> Inspection End.
NO >> Check ground harness.
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) : Diagnosis
O
Regarding Wiring Diagram information, refer to BCS-107, "Wiring Diagram".
P
1.CHECK FUSES AND FUSIBLE LINK
Check that the following fuses and fusible link are not blown.
BCM
Ground Continuity
Connector Terminal
M20 67 — Yes
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair harness or connector.
Select the DATA MONITOR for the METER/MA and check the BUZZER monitor value.
E
BUZZER
Under the condition of buzzer input : On
Except above : Off
F
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-53, "Removal and Installation" (Type A) or MWI-104,
"Removal and Installation" (Type B). G
NO >> Replace BCM. Refer to BCS-69, "Removal and Installation" (with Intelligent Key) or BCS-122,
"Removal and Installation" (without Intelligent Key).
Diagnosis Procedure INFOID:0000000009269302 H
WCS
34 - Ground
When driver seat belt is fastened : Approx. 12V
When driver seat belt is unfastened : Approx. 0V
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-53, "Removal and Installation".
NO >> GO TO 2
2. CHECK SEAT BELT BUCKLE SWITCH LH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter and seat belt buckle switch LH.
3. Check continuity between combination meter harness connector M24 terminal 34 and seat belt buckle
switch LH harness connector B13 terminal 1.
1– 2 D
When seat belt is : Continuity should not exist.
fastened
E
When seat belt is : Continuity should exist.
unfastened
Is the inspection result normal? F
YES >> Inspection End.
NO >> Replace the seat belt buckle switch LH.
TYPE B G
I
1. CHECK COMBINATION METER INPUT SIGNAL
Select “DATA MONITOR” for “METER/M&A” and check the “SEAT BELT W/L” monitor value.
J
SEAT BELT W/L
When seat belt is fastened : OFF
When seat belt is unfastened : ON K
Is the inspection result normal?
YES >> Inspection End.
L
NO >> Refer to WCS-37, "TYPE B : Diagnosis Procedure".
TYPE B : Diagnosis Procedure INFOID:0000000009269305
9 - Ground P
When driver seat belt is fastened : Approx. 12V
When driver seat belt is unfastened : Approx. 0V
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-104, "Removal and Installation".
NO >> GO TO 2
1– 2
When seat belt is : Continuity should not exist.
fastened
When seat belt is : Continuity should exist.
unfastened
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace the seat belt buckle switch LH.
KEY ON SW D
When key is inserted into key cylinder : ON
When key is removed from key cylinder : OFF E
Is the inspection result normal?
YES >> Inspection End.
NO >> Refer to WCS-39, "Diagnosis Procedure". F
Diagnosis Procedure INFOID:0000000009269313
G
Regarding Wiring Diagram information, refer to WCS-23, "Wiring Diagram".
H
1. CHECK FUSE
Check if the key switch 10A fuse [No. 8, located in the fuse block (J/B)] is blown.
I
Is the fuse blown?
YES >> Replace the fuse after repairing the affected circuit.
NO >> GO TO 2
J
2. CHECK BCM INPUT SIGNAL
Check voltage between BCM harness connector M18 terminal 37 and ground.
K
Terminals
(+) Voltage
Condition L
(−) (Approx.)
BCM
Terminal
connector
Key is inserted Battery voltage
M18 37 Ground M
Key is removed 0V
Is the inspection result normal?
YES >> Inspection End. WCS
NO >> GO TO 3
3. CHECK KEY SWITCH CIRCUIT
O
1. Disconnect BCM connector M18 and key switch.
2. Check continuity between BCM harness connector M18 terminal 37 and key switch harness connector
M27 terminal 1.
P
BCM Key switch
Continuity
Connector Terminal Connector Terminal
M18 37 M27 1 Yes
3. Check continuity between BCM harness connector M18 terminal 37 and ground.
BCM
Continuity
Connector Terminal Ground
M18 37 No
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace harness.
4. CHECK KEY SWITCH POWER SUPPLY CIRCUIT
Check voltage between key switch harness connector M27 terminal 2 and ground.
Terminals
Voltage
(+)
(–) (Approx.)
Key switch Terminal
M27 2 Ground Battery voltage
Is the inspection result normal?
YES >> Replace key switch.
NO >> Repair or replace harness.
Component Inspection INFOID:0000000009269314
1 –2
When key is inserted : Continuity should exist.
into key cylinder
When key is removed : Continuity should not exist.
from key cylinder
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace key switch.
PKB SW
E
Parking brake depressed : ON
Parking brake released : OFF
Is the inspection result normal? F
YES >> Inspection End.
NO >> Refer to WCS-41, "TYPE A : Diagnosis Procedure".
G
TYPE A : Diagnosis Procedure INFOID:0000000009269321
H
Regarding Wiring Diagram information, refer to WCS-23, "Wiring Diagram".
(+) (−)
Voltage
Combination meter Condition K
(Approx.)
Connector Terminal
Ground
Ignition When parking brake is applied 0V
M24 37
switch ON When parking brake is released 12 V L
Terminals
Combination meter Parking brake switch Continuity P
Connector Terminal Connector Terminal
M24 37 M17 1 Yes
4. Check continuity between combination meter harness connector and ground.
Terminals
Combination meter Continuity
Connector Terminal Ground
M24 37 No
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair harness or connector.
TYPE A : Component Inspection INFOID:0000000009269322
PKB SW
Parking brake depressed : ON
Parking brake released : OFF
Is the inspection result normal?
YES >> Inspection End.
NO >> Refer to WCS-42, "TYPE B : Diagnosis Procedure".
TYPE B : Diagnosis Procedure INFOID:0000000009269317
(+) (−) A
Voltage
Combination meter Condition
(Approx.)
Connector Terminal
Ground B
Ignition When parking brake is applied 0V
M82 10
switch ON When parking brake is released 12 V
Is the inspection result normal? C
YES >> Inspection End.
NO >> GO TO 2.
2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT D
Terminals
F
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
Diagnosis Procedure INFOID:0000000009269324
NOTE:
To identify combination meter type, refer to MWI-55, "Information" or MWI-5, "Information".
1.CHECK PARKING BRAKE WARNING LAMP
1. Start the engine.
2. Check the operation of the brake warning lamp by operating the parking brake.
NOTE:
To identify combination meter type, refer to MWI-55, "Information" or MWI-5, "Information". D
1.CHECK SEAT BELT WARNING LAMP
1. Turn ignition switch ON.
E
2. Check operation of seat belt warning lamp in combination meter.
WCS
Light reminder warning chime does not sound even though headlamps are illuminated.
Diagnosis Procedure INFOID:0000000009269328
The key warning chime does not sound, when all of the following conditions are fulfilled. B
• Key inserted into the key cylinder (key switch signal ON).
• Ignition switch is in ACC or OFF (ignition switch signal OFF).
• Driver side door is open (driver side door switch ON)
C
Diagnosis Procedure INFOID:0000000009269330
WCS