Professional Documents
Culture Documents
User Guide
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
2
OPERATION GUIDE BY FUNCTION
Screen Configuration
Vehicle identification screen
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
3
Screen configuration after vehicle identification
4
1
2 5
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
4
Control Menu
The control menu is displayed constantly and menus can be used when they are selected.
1
2
3
4
5
1. Change Vehicle
Returns to the vehicle identification screen for the next vehicle to be identified.
2. Settings
Changes the language and units.
3. About
Displays the MDARS version.
4. Log Out
This function is not available.
5. Exit
Ends the MDARS and closes the window.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
5
Quick Check
DTCs stored in all of the modules can be confirmed.
1. Network view
All of the modules which can be equipped on the vehicle are displayed using box-shaped icons.
When a module (orange color) with a DTC stored is selected, the details of the DTC stored in the
module are displayed.
Note
Modules which have/do not have DTCs or modules which cannot communicate can be identified
visually by the module color.
Color Description
Green No DTCs
2. DTC list
For details, refer to [DTC Confirmation] (P.15).
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
6
Toolbox
Groups the diagnostic repair functions according to the work.
1
2
3
Maintenance
Groups the functions used for maintenance.
Note
This function is not available with the MDARS release at the beginning of February 2019. This
function will be available with the future version update.
1. Diagnosis
Groups the functions used for diagnosis.
2. Work Support
Groups the functions used for work other than diagnosis.
3. Accessories
Groups the functions used for accessories.
Note
When is selected, the function list closes.
When / is selected, all of the function display/non-display can be switched.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
7
Vehicle Identification
Automatic Vehicle Identification
1. Launch MDARS and select [Start] from the [Vehicle Identification] list
Performs verification of connection information between each system and collects vehicle
information.
: Between laptop PC and Cloud
: Between laptop PC and VCM-II
: Between vehicle and VCM-II
: Vehicle information collection
If the vehicle is a model compatible with MDARS, the check results are displayed on the network view
screen of the [Quick Check] tab. For details, refer to [Quick Check] (P.6).
If the vehicle is a model not compatible with MDARS, the IDS launches.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
8
If vehicle identification is unsuccessful
The icon is displayed in red.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
9
Manual Vehicle Identification
If the automatic vehicle identification is unsuccessful two times, the manual VIN entry screen is
displayed.
1. Enter the VIN and select [Proceed]
Note
Text information from other software/systems can be copied and pasted to the VIN field.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
10
3. Select the necessary items and select [Proceed]
Note
Selection items differ depending on the vehicle model.
If the vehicle is a model compatible with MDARS, the check results are displayed on the network view
screen of the [Quick Check] tab. For details, refer to [Quick Check] (P.6).
If the vehicle is a model not compatible with MDARS, the IDS launches.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
11
Change VCI
Selects the VCM-II to be used.
1. Launch MDARS and select [Change] from the [Change VCI]
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
12
No Vehicle Mode
Can confirm when and what kind of work was done using MDARS for vehicles designated by VIN.
Note
This function is not available with the MDARS release at the beginning of February 2019. This
function will be available with the future version update.
1. Launch MDARS and select [No Vehicle Mode] from the [Start with no connected vehicle]
Note
Text information from other software/systems can be copied and pasted to the VIN field.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
13
The diagnostic and repair data on the vehicle selected is displayed.
Note
Select to refresh the diagnostic and repair data on the vehicle selected.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
14
DTC Confirmation
1. Select from the [Quick Check] tab
The DTC list screen is displayed.
2
3
4
6
The list of DTCs stored in multiple modules can be confirmed on the DTC list screen.
1. DTC list
DTCs stored in multiple modules can be confirmed on the list.
Note
When is selected, the display order can be changed.
Module order
DTC order
Failure Type order
Status order
2. DTC clearing
For details, refer to [DTC clearing] (P.16).
3. Filter function
The displayed DTCs can be narrowed down.
4. DTC refresh
DTCs are refreshed.
5. Display of freeze frame data/snapshot data
Items which the freeze frame data/snapshot data can use are displayed. For details, refer to [Display of
Freeze Frame Data/Snapshot Data] (P.18).
6. Status
Indicates a current or past malfunction for each DTC.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
15
DTC clearing
1. Select from the [Quick Check] tab
2. Select [Yes]
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
16
3. Select [Next]
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
17
Display of Freeze Frame Data/Snapshot Data
The recorded vehicle and system conditions when a DTC is detected can be confirmed.
Freeze frame data/snapshot data for DTCs which display a on the DTC list screen can be displayed.
Note
This function is not available with the MDARS release at the beginning of February 2019. This
function will be available with the future version update.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
18
History of Diagnosis
Can confirm when and what kind of work was done using MDARS for the vehicle currently connected.
1. Select [Diagnosis] or [Work Support] from the [Toolbox] tab
2. Select [Run] from [History of Diagnosis]
Note
Select to refresh the diagnostic and repair data on the vehicle selected.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
19
DataLogger
The datalogger consists of a PID/data monitor which displays input/output signals of modules in real time
and a simulation function which drives output-related parts optionally.
Note
This function is not available with the MDARS release at the beginning of February 2019. This
function will be available with the future version update.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
20
4. Select the module
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
21
Main icons on datalogger screen
Icon Explanation
Returns to the initial selection screen of the datalogger.
Displays the screen for switching between the value display/graph display.
Trigger conditions can be set for automatically starting/ending live view capture.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
22
Setting PID display/non-display separately
1. Select from the datalogger screen
2. Move the PIDs you do not want to display to the window on the left and the ones you
want to display to the window on the right
Note
Move and change the order by selecting an arrow button ( / / / ) or dragging and
dropping a PID.
3. Select
The PID moved to the window on the right is displayed.
Note
When the name is set and is selected, the current PID list can be saved as a setup.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
23
PID/Data Monitor
The PID/data monitor is a function which can display input/output signals of modules in real time.
In the input/output signals which can be displayed, there is input information for each switch/sensor, drive
information for each actuator, and control information for each system.
For the display method, selection can be made from the value display/bar graph display/line graph
display.
Ex.: When monitoring using a bar graph display
1. Select from the datalogger screen
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
24
Switches to the bar graph.
Note
When is selected, it switches to the value display, and when is selected, it switches to
the line graph display.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
25
Capture and save
The live view can be captured during display.
1. Displaying live view to be captured
2. Select
Caution
The data is saved to the cloud server. For the purposes of personal information protection, be
careful not to input information such as customer names and addresses.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
26
Playback captured live views
1. Select [Recordings] from the [Datalogger] tab
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
27
2. Select the live view to be confirmed
1. Captured data
2. Playback range
The playback range of the captured data can be changed by moving the / .
3. Display position
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
28
Overlap display function for line graphs
Line graphs of PID/data monitor can be overlapped.
Ex.: Overlapping [STR_ANG] on [APP]
1. Select from the [APP] on the display switching screen
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
29
2. Select from the [STR_ANG]
Note
When is selected, the overlap display is canceled.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
30
3. Select from the [Live View] tab
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
31
Creating a new setup
Several PIDs often used in diagnosis can be compiled and saved as 1 setup.
1. Move the PIDs you do not want to display to the window on the left and the ones you
want to display to the window on the right from the PID selection screen
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
32
Using a setup
Displays several PIDs set in a setup.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
33
Other Diagnostic Repair Functions
Items other than read/clear DTC and datalogger, such as sensor initialization and operation history, can
be confirmed.
Ex.: When doing [Front Wiper Position Learning]
1. Select [Work Support] from the [Toolbox] tab
2. Select from the [WIPER/WASHER SYSTEM] menu
The wiper and washer system-related work support function list is displayed.
3. Select [Run] from the [Front Wiper Position Learning]
Note
When is selected, the function list closes.
When / is selected, all of the function display/non-display can be switched.
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
34
Ending MDARS
1. Select [Exit] from the control menu
2. Select [Yes]
Screens are for February 2019. Screens may be updated depending on MDARS version updates.
35