Professional Documents
Culture Documents
Please Note: Scissor Lift must be installed in accordance with the requirements
of the Local Building Codes, the Canadian Electrical Code (CEC), CAN/CSA
C22.1 and the National Electric Code(NEC), NFPA 70. An appropriate disconnect
device shall be provided as part of the building installation.
If you encounter any difficulties installing or servicing your Scissor Lift, call your
Copyright © 2008 Draper Inc. Form ScissorLift_Inst08-R Printed in U.S.A. dealer or Draper, Inc. in Spiceland, Indiana, 765-987-7999, or fax 765-987-7142.
Scissor Lift by Draper page 2 of 6
Installing Projector Installing Optional Environmental Air Space Housing
Depending on job conditions and projector, it may be easier to remove The Environmental Air Space Housing is shipped in pieces, and must be
optional ceiling closure panel before installing projector. assembled by the installer. The height of the Environmental Air Space Housing
Generally, the video projector should be suspended from the bottom pan can be adjusted by up to 2" (5 cm) by moving the trim frame to different mounting
according to projector manufacturer’s instructions and recommended standard holes in side panels. It is recommended that an access panel be installed in the
ceiling mounting hardware. For projectors 26 lbs. or below, use Draper's Low ceiling to allow future access.
Profile Mount with Universal Projector Bracket. ➀ Attach Environmental Air Space Housing top frame to top of Scissor Lift with
bolts provided (7, 8).
The Scissor Lift has a grounded 110-120V AC, 60Hz power cord for
➁ Install top panel to Environmental Air Space Housing frame.
projector power supply. The power cord is laced down the back scissor and is ➂ Attach assembly to overhead structure. Allow clearance between Environmental
“hot” at all times. Air Space Housing top and structure for ease of future access.
Control cables should be laced through our Cable Management System. ➃ Install side and end panels, and trim frame.
Make sure to use flexible cables, and to allow enough cable at each turn
so cables do not stretch or kink. This will ensure that cords do not become Parts List for Scissor Lift Environmental Air Space Housing
tangled and damaged during Scissor Lift operation.
Item Quantity Part
Unit and projection system should be operated, checked and adjusted as
necessary at this time. 1 1 Environmental Air Space Housing Top Frame
After testing operations, the optional closure panel should be reattached.
2 2 Environmental Air Space Housing End Panel
Be sure to use Loctite®, or other thread locking compound on the nuts.
NOTE: Immediately upon completion of the surrounding ceiling, units should 3 2 Environmental Air Space Housing Side Panel
be operated to confirm that optional ceiling closure panel stops just short of
4 1 Environmental Air Space Housing Top Panel
touching ceiling in closed position.
Warning: Keep fingers and other objects away from automatic ceiling 5 varies #10-32 x 3/8" Hex Head Screw with Zinc Washer
closure and scissor mechanisms when unit is operating. Serious injury or
6 varies #8-32 Zinc Keps Lock Nut
damage could result.
7 varies ½"-13 x 3½" Zinc Hex Head Screw
8 varies ½"-13 Zinc Hex Grd 2
Some Environmental Air Space Housings are longer than 3
wide and mounting hole locations for Environmental Air 9 varies /16" ID x 5" OD x 1/16" tk Flat Washer
Space Housing will change. 10 varies ¼"-20 x 1½" Zinc Hex Head Screw
11 varies ¼" Flat Zinc Washer
12 varies ¼"-20 Zinc Nylon Insert Lock Nut
Caution: Beware of 13 1 Trim Frame
pinch points
Scissor Lift Environmental
4 Air Space Housing
(Exploded View)
6 5 3
13 7 8
6
1 9
10 11 12
Caution: Be careful when handling Environmental Air Space
Housing Panels. The panels could have sharp edges.
BK
WH
electrician BK
BK
YW
GN
YW
BK
WH
Scissor Lift by Draper
WH BE BK
Capacitor
1 2 3 4 5 6 7 8 9 10
YW
3x3
Up Relay Down Relay
3A
Connection
1A
BE
10A
BE NC BE NC Board
NO RD NO BK BE GN
RD COM RD BE COM BK Motor
RD RD RD
(-) (+) (-) (+) 1 2 3 4 5 6 7 8 9 10
www.draperinc.com
RD BK
BE RD BE BK
BK BK
BK RD BK BK BK
BK
GN
(765) 987-7999
YW BE RD RD RD BK BE BK BK RD
Down
Key
Wall Switch
Limit switch Up BE BE GN Up
Limit BE Toggle
Common YW Dn
Switch Switch
(DPDT)
Key (Yellow)
Down Down WH BE
RD not used
Service position Show position BK BN Up
Limit switch Limit switch BE Key
BE BN WH BK GN RD (Red) Momentary
RD BK
RD BE RD GN WH Key
12V Down
(Brown) Switch
Terminal Strip
24V Switching
page 5 of 6
Scissor Lift by Draper page 6 of 6
Front Rear
Show Position
Adjustments