\\
UDC 621,882. 082. 1:621.753.1
JAPANESE INDUSTRIAL STANDARD
Limits of Sizes and Tolerances
for Metric Fine Screw Threads
JIS B O21 1 -
Translated and Published
by
Japanese Standards Association
ae
Printed in Japen 458‘Translation without guarantee
In the event of any doubt arising, the original
standard in Japanese is to be evidence
oO
&
\qUDC 621.882.082,1:621.753.1
JAPANESE INDUSTRIAL STANDARD sis
Limits of Sizes and Tolerances B 0211-1982
for Metric Fine Screw Threads
1. Scope
This Japanese Industrial Standard specifies the limits of sizes and
tolerances for metric fine screw threads(') specified in JIS B 0207 to be
used mainly for fastening.
The limits of sizes and tolerances for Quality 1, Quality 2 and Quality
3 for ML < 0,2 to M300 x 4 in designation of screw threads shall be in
accordance with Appendix.
Note (1) The fine screw threads excluding M14 x 1.25,
The limits of sizes and tolerances for this screw thread
of M14 X 1.25 shall be in accordance with JIS B 8031 and JIS
W 4501,
Remark: The Limits of sizes and tolerances specified in the body of
this standard are in accordance with JIS B 0215, and limits of
sizes for medium quality of metric fine screw threads specified
in 180 965/2 are contained in Attached Table 3 and Attached
Table 4.
Applicable Standards:
JIS B 0123-Designation of Screw Threads
JIS B 0207-Metric Fine Screw Threads
JIS B 0215~Tolerance System for Metric Screw Threads
JIS B 0252-Limit Gauges for Metric Fine Screw Threads
JIS B 1051-Mechanical Properties of Bolts and screws
JIS B 8031-Spark Plugs for Internal Combustion Engines
JIS W 4501-Spark Plugs for Aircraft Piston Engines
JIS 2 8401-Rules for Rounding Off of Numerical Values
Reference Standards:
ISO 965/1-1980 ISO general purpose metric screw threads-Tolerances~
Part 1: Principles and basic data.
180 965/2-1980 ISO general purpose metric screw threads~Tolerances-
Part 2: Limits of sizes for general purpose bolt and
nut threads-Medium quality.2
B 0211-1982
2, Relations of Basic Profiles, Basic Dimensions, Limits of Sizes
Tolerances and Fundamental Deviations
The relations of basic profiles, basic dimensions, limits of sizes,
tolerances and fundamental deviations are shown in Fig. 1.
Fig. 1. Figure of Relations of Basic Profiles, Basic Dimensions,
Limits of Sizes, Tolerances, and Fundamental Deviations
for Metric Fine Screw Threads
(1) In the Case of GH, SH, 6H and 7H (ET
(2) In the Case of 4h and 6h (e=0) (3) In the Case of 6g and 8g (e# <0)
@ 3) 3) € External External
aes xterna,
+ 3] S| thread thread
‘The meaning of symbols in Fig. 1 is as follows:
D, Das and Dain: basic dimension, maximum and minimum permissible
dimensions of major diameter of internal thread.
Dy Diminy Denny t basic dimension, maximum and minimum permissible
Te, and BI dimensions, tolerance and fundamental deviation
of pitch diameter of internal thread.
Ds, Dimesy Dining basic dimension, maximum and minimum permissible
T», and Ef dimensions, tolerance and fundamental deviation
of minor diameter of internal thread.3
B 0211-1982
4, dot, doin Te and est basic dimension, maximum and minimum permissible
dimensions, tolerance and fundamental deviation
of major diameter of external thread.
dy dime, dawnt basic dimension, maximum and minimum permissible
Th and es dimensions, tolerance and fundamental deviation
of pitch diameter of external thread.
dy dime and dima + basic dimension, maximum and minimum permissible
dimensions of minor diameter of external thread.
The bold continuous Lines show the basic profile, and the oblique-lined
portion shows permissible range of internal or external thread.
The numerical values of D, D:, Dj, dy dz and cd) ave specified in Table 4
of JIS B 0207,
3. Fitting Qualities, Classes, Limits of Sizes, and Tolerances of Screw
Threads
The fitting qualities shall be divided into Fine, Medium, and Coarse,
and the corresponding classes shall be as shown in following Table.
‘The limits of sizes and tolerances shall be in accordance with Attached
Table 1 to Attached Table 6, according to the division in following Table.
The tolerance classes, limits of sizes and tolerances in Attached Table 1
to Attached Table 6 are shown refering to thread engagement group N specified
in JIS B 0215, however, in the case of S whose length of thread engagement is
shorter and in the case of L whose length of thread engagenent is longer,
those shall be in accordance with JIS B 0215.
Further, independent of fitting quality, the combination of internal and
external threads of different class may be used, as required.
Table
Fiteing quality | 2iviston inco Tolerance | Applicable
(Example of application) | yee ney Chread class (2) Table
Fine Internal 4SH(ML.8 x 0.2 max.) Attached
Example of application: cieeed 5H(M2* 0.25 min.) ore
Fine screw thread with
particularly smal External seeached
clearance. thread ae Table 24
B 0211-1982
Table (Continued)
Fitting fe oa Tolerance Applicable
quality external thread class (?) Table
Ned sum Internal on aeached
Example of application: thread Table 3
General purpose screw
thread to be used for External 6h(M1.4 x 0.2 max.) Attached
machines, devices and | — Extern ecrer
constructions, 6g(M1.6% 0.2 min.)
Coarse
Example of application:
Screw threads to be
Internal Attached
used under circum 7a
stances easily to be eee ao
stained or damaged
such as in buliding
works, installation,
or the like, and serew
threads which are
aLEficult in threading ern
work such as in thread-| Pxternal 8g Raeicree
cutting the hot-rolled
bar or in threading in
the long blind hole.
Note (#) Designation of tolerance class
ois.
shall be in accordance with JIS B
Remarks 1, Fine, Medium and Coarse of Fitting quality in this Table corre~
spond to tolerance quality of fine, medium, and coarse in ISO
965/1, and the tolerance classes
selected from the recommended tol
965/1.
referring to fitting quality are
erance classes specified in ISO
2. S, N, and L of length of engagement coincide with $, N, and L in
thread engagement groups specified in ISO 965/1.
4. Designation
The designation of screw thread i
the body of this standard shall be in
Example: M6 x 0.75 — 68
MG x 0.75 — 6g
ncluding tolerance class according to
accordance with JIS B 0123.
OQ