Professional Documents
Culture Documents
Disclaimer. All representations and recommendations set forth are given in good faith and to the best of our knowledge. Howev er due to
varying conditions and applications, the buyer shall conduct its own tests of this product before use. Under no circumstances will the
manufacturer be liable for any loss or damages caused by incorrect usages. The sale of this product shall be on terms and con ditions set
forth on Pentens order acknowledgement.
Product Data Sheet
Instruction for Use For more details, please refer to our Technical
Department.
Surface Preparation
Ensure that the surface to be treated is free from Curing
any loose particles, dust, oil, dirt, extra cement Allow the coating to cure thoroughly before
blocks and especially sand. applying the next coat. Depending on
Clean a second time, using a soft broom or a temperature, humidity and wing conditions,
vacuum cleaner, to make sure that the surfaces normally 1~8 hours should be taken between
are absolutely dust free. two coats.
Priming Note
Apply one coat of diluted PENTENS T-007 (1 The best method to assure good penetration of
portion of T-007 with 3 portions of water) by the first coat into the surface is by application
roller, brush or spray gun. with a nap roller. The succeeding coats may be
When applying on a defective bitumen layer use spray or roller applied.
0.1kg/m2.
For concrete surfaces use 0.2~0.3 per m2. Cleaning
Note: It is advised for a heavy duty and long Tools and equipment just can be clean with
lasting application to lay special fiber PENTENS clean water immediately, after use. Hardener
W-015 on the surface to be treated. This fiber material can only be mechanically removed.
can be applied on the pre-existing cracks only.
Application
Safety
PENTENS T-201 is non-toxic. For personal
On areas exposed hot drying winds. 2 to 3 thin
precautions, applicators are recommended to
coats of paint may be more successful than 1
wear gloves and goggles when handling
thick coat.
PENTENS T-201. Treat any splashes to the skin
or eyes with fresh water immediately. Should
PENTENS T-201 is suggested to apply at least 2
any of the products be accidentally swallowed,
coats. The first coat should be applied in one
do not induce vomiting, call for medical
direction only. If possible the second coat should
assistance immediately.
be applied at right angles to the first. Leave to
cure for approximately 8 hours before applying
second coat. PENTENS T-201 can be installed
with conventional airless spray equipment, brush
or roller.
Consumption
On concrete roofs: 1kg/m2/per coat
On facade/vertical: 0.5~1kg/m2/per coat
2
1.3kg/m per coat when PENTENS W-015
Glass Fiber Mesh is used.
2
1.0kg/m per coat when PENTENS W-015
Glass Fiber Mesh is not used.
Pentens T-201 also can be used as a coating for building facades and several
types of concrete, concrete block, brick and stucco structures and retaining
walls.
Good Elastic
Elongation > 200 %
Crack Seal
Excellent Bonding
ADVANTAGES:
- Completely waterproof
- Excellent elastic regain
- Flexible at low temperatures
- Superb adhesion to all sound roofing surfaces
- Outstanding exterior durability UV light, infra-red and
ozone resistance
- High resistance to dirt pickup hence long term reflectivity
and lower air-conditioning costs
- Low toxicity and odor
- Low moisture-vapor transmission
- Excellent film integrity
- Easy application
- Easy cleaning
- Pedestrian properties of the roofing membrane
8
SURFACE PREPARATION TECHNICAL & PHYSICAL DATA
Ensure that the surface to be treated is free from any loose particles,
dust, oil, dirt, extra cement blocks and especially sand. Clean a Form Liquid
second time, using a soft broom or a vacuum cleaner, to make sure Color Grey, white, green
that the surfaces are absolutely dust free.
Resin Acrylic
PRIMING Density 1.20 ± 0.1 kg/litre
Apply one coat of diluted Pentens T-007 (1 portion of T-007 with 3
portions of water) by roller, brush or spray gun. Solid content > 60% by weight
NOTE
The best method to assure good penetration of the first coat into the
surface is by application with a nap roller. The succeeding coats may
be spray or roller applied.
CLEANING
Tools and equipment just can be clean with clean water immediately,
after use. Hardener material can only be mechanically removed.
SAFETY
Pentens T-201 is non-toxic. For personal precautions, applicators
are recommended to wear gloves and goggles when handling
Pentens T-201. Treat any splashes to the skin or eyes with fresh water
immediately. Should any of the products be accidentally swallowed,
do not induce vomiting, call for medical assistance immediately.
9