Professional Documents
Culture Documents
Performance Standby
Frequency 60 Hz
Genset Power Rating 625 kVA
Gen set power rating with fan @ 0.8 power factor 500 ekW
Fuelling strategy TIER 3
Performance Number DM8155
Fuel Consumption
100% load with fan 137.0 L/hr 36.2 gal/hr
75% load with fan 110.5 L/hr 29.2 gal/hr
50% load with fan 71.3 L/hr 18.8 gal/hr
25% load with fan 41.9 L/hr 11.1 gal/hr
Cooling System 1
Radiator air flow restriction (system) 0.12 kPa 0.48 in. Water
Radiator air flow 720 m3/min 25426 cfm
Engine coolant capacity 20.8 L 5.5 gal
Radiator coolant capacity 54 L 14 gal
Total coolant capacity 75 L 20 gal
Inlet Air
Combustion air inlet flow rate 38.2 m³/min 1347.7 cfm
Max. Allowable Combustion Air Inlet Temp 49 ° C 120 ° F
Exhaust System
Exhaust stack gas temperature 531.1 ° C 988.0 ° F
Exhaust gas flow rate 102.1 m³/min 3605.5 cfm
Exhaust system backpressure (maximum allowable) 10.0 kPa 40.0 in. water
Heat Rejection
Heat rejection to jacket water 182 kW 10375 Btu/min
Heat rejection to exhaust (total) 493 kW 28039 Btu/min
Heat rejection to aftercooler 121 kW 6860 Btu/min
Heat rejection to atmosphere from engine 91 kW 5182 Btu/min
Heat rejection from alternator 29 kW 1655 Btu/min
LEHE2011-04 1/2
Cat C15 GC ®
DIESEL GENERATOR SETS
Skid (Wide 4815 (189.6) 1630 (64.2) 2034 (80.1) 3756 (8280.6)
Base)
Integral Tank 4815 (189.6) 1630 (64.2) 2584 (101.7) 4693 (10346.3)
base
Total
Tank Useable Capacity
Capacity
Design
2
Emissions data measurement procedures are consistent with those described in EPA CFR 40 Part 89, Subpart D & E and ISO8178-1 for measuring HC, CO,
PM, NOx. Data shown is based on steady state operating conditions of 77° F, 28.42 in HG and number 2 diesel fuel with 35° API and LHV of 18,390 BTU/lb.
The nominal emissions data shown is subject to instrumentation, measurement, facility and engine to engine variations. Emissions data is based on 100%
load and thus cannot be used to compare to EPA regulations which use values based on a weighted cycle.
3
UL 2200 Listed packages may have oversized generators with a different temperature rise and motor starting characteristics. Generator temperature rise
is based on a 40° C ambient per NEMA MG1-32.
STANDBY: Output available with varying load for the duration of the interruption of the normal source power. Average power output is 70% of the standby power
rating. Typical operation is 200 hours per year, with maximum expected usage of 500 hours per year.
RATINGS: Ratings are based on SAE J1349 standard conditions. These ratings also apply at ISO3046 standard conditions.
Fuel Rates are based on fuel oil of 35º API [16º C (60º F)] gravity having an LHV of 42 780 kJ/kg (18,390 Btu/lb) when used at 29º C (85º F) and weighing 838.9 g/litre
(7.001 lbs/U.S. gal.). Additional ratings may be available for specific customer requirements, contact your Caterpillar representative for details. For information
regarding Low Sulfur fuel and Biodiesel capability, please consult your Cat dealer.
LEHE2011-04 (11-19)
www.Cat.com/electricpower
©2019 Caterpillar All rights reserved. Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication. CAT, CATERPILLAR, their
respective logos, “Caterpillar Yellow”, the “Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without 2/2
permission.
Cat GC ®
Control Panel
FEATURES
• 4-line back-lit LCD text display
• Multiple display languages
• Five-key menu navigation
• LCD alarm indication
• Customisable power-up text and images
• Data logging facility
• Internal PLC editor
• Protections disable feature
• Fully configurable via PC using USB & RS485 communication
• Front panel configuration with PIN protection
• Power save mode
• 3-phase generator sensing and protection
• Generator current and power monitoring (kW, kvar, kVA, pf)
• kW and kvar overload and reverse power alarms
• Over current protection
• Unbalanced load protection
• Breaker control via fascia buttons
• Fuel and start outputs configurable when using CAN
• Support for 0 V to 10 V & 4 mA to 20 mA sensors
• 8 configurable digital inputs (3 available for Customer use)
• 8 configurable digital outputs (5 available for Customer use)
• 4 configurable analogue outputs (3 available for Customer Use)
• CAN, MPU and alternator frequency speed sensing in one variant
• Real time clock
• Engine pre-heat and post-heat functions
• Engine run-time scheduler
• Engine idle control for starting &stopping
• Fuel usage monitor and low fuel level alarms
• 3 configurable maintenance alarms
BENEFITS
• Hours counter provides accurate information for monitoring and maintenance periods
• User-friendly set-up and button layout for ease of use
• Multiple parameters are monitored & displayed simultaneously for full visibility
• The module can be configured to suit a wide range of applications for user flexibility
• PLC editor allows user configurable functions to meet user specific application requirements .
• RS485 Communication port can be used for the Remote Monitoring Communication
(Compatible with Cat PLG)
LEHE2017-01 (11-19)
www.Cat.com/electricpower
©2019 Caterpillar All rights reserved. Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication. CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow”,
the “Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
&-!&
$=> 2
? 8@ 88
'
6
'
$ &
$
'%
"&.
"&. /! -# %
$ - %
$ - 3+ - 3+ -
'%
!* & *%$+ ! !* & -- & -# !
#$
& $ $ & !#$ $ $
-
(" ) !
#$
(/-)
("-)
# $ %" " &%" % &% %
'
' %
'
( (
( ( ( ( ( (
( (
( (
( (
( ( (
( (
(
( (
(
( (
'
$ &
$
'%
!& !& !& !& * $ %
$ %&
'%
* $ %
$ %& * $ 3+ ' * $ 3+ /! &0 3+ /!
!* & *%$+ ! !* & !#$ $ & !#$ $ $ /! -!* !#$ $ * $ -!* -!* -!* &$ (78 -!* &$
-
&$ 3+ ' /! &$ &$ ' -
(78 ' -
-!* &$ 89:9 %
+') 89:9 %
+')
# $ %" %
' ') ') &% &% '&) '&)
( ( ( (
( ( ( ( (
( ( (
(
( ( (( (
( ( ( ((( (
( ( ((
(
(( (
(( ((
( (
(( ( (( ( ((
+
6 &;6<
6
'
$ &
$
'%
& 2 $%!
& 2 $%!
& 2 $%!
3+#$ -&! !% -&! *!&. !* + $ +%'+ + $
!* & *%$+ ! !* & $! 2. $ $! $! 3+ & !/ &0 !! & -$ &!! &
&'0 /# /#
-
*$ & $!+ & $! 7-
&'0
&'0
"*+, -.
&-!&
$=> 2
? 8@ 88
# $ %" !&) !&) !&) !&) !&) !&) !&) !&) !&)
(
( ((
( ( ( ( (
( ( ( ( (
( (( ( ( ( (
( ( ( ( ( ( (
( ( ( (( ((
( ( (
( (( ( (
( (
((( (
( ( ( ((
<AA<A
6
"*+, -.
&-!&
$=> 2
? 8@ 88
&
6? %
6<
6<6G
6
6
AA &
6 &
6A &9DE
&-!&
-%
%$%!
"
' )
' )
""4
'!
'
)"%
'
)
! .-9 :*976, ,6+76,@ *6D
( .-9 -<F,9
,6+76,@ 9,.,9,6;, *<:-@8F,97; 89,@@?9, 7@ #" 0 76 F+1
*6D @<*6D*9D <,:8,9*<?9, 7@ D,+ 0 D,+ '1 *< $ 9,=*<7>,
F?:7D7<C *< <F, @<*<,D *.<,9;--=,9 B*<,9 <,:8 -9 76=,< :*67.-=D
<,:8
'
"
0
1 %
'%
"
0 1
/
!/
6+76, ;-99,;<,D +9-@@ -?<8?< 76;=?D,@ <F, 8-B,9 9,E?79,D <- D97>,
@<*6D*9D ,E?78:,6<K =?A, -7= @;*>,6+, =?A, -7= .?,= <9*6@.,9
;-::-6 9*7= .?,= @,8*9*<, ;79;?7< *.<,9;--=,9 *6D H*;G,< B*<,9
8?:8@
6+76, 6,< 8-B,9 *>*7=*A=, .-9 <F, ,5<,96*= 0.=CBF,,=1
=-*D 7@ ;*=;?=*<,D AC @?A<9*;<76+ <F, @?: -. *?57=7*9C =-*D .9-:
<F, ;-99,;<,D +9-@@ .=CBF,,= -?< 8?< 8-B,9 C87;*= *?57=7*9C
=-*D@ *9, 9*D7*<-9 ;--=76+ .*6@ FCD9*?=7; 8?:8@ *79 ;-:89,@@-9@
*6D A*<<,9C ;F*9+76+ *=<,96*<-9@ '-9 7,9 ( 9*<76+@ *DD7<7-6*=
"*9*@7<7; =-@@,@ B-?=D *=@- 76;=?D, 6<*G, *6D
5F*?@<
,@<97;<7-6@
!
"
=<7<?D, ;*8*A7=7<C 7@ <F, :*57:?: *=<7<?D, *A->, @,* =,>,= *<
@<*6D*9D <,:8,9*<?9, *6D @<*6D*9D 89,@@?9, *< BF7;F <F, ,6+76,
;-?=D D,>,=-8 .?== 9*<,D -?<8?< 8-B,9 -6 <F, ;?99,6< 8,9.-9:*6;,
"*+, ( -.
&-!&
$=> 2
? 8@ 88
D*<* @,<
<*6D*9D <,:8,9*<?9, >*=?,@ >,9@?@ *=<7<?D, ;-?=D A, @,,6 -6
)
F,6 >7,B76+ <F, *=<7<?D, ;*8*A7=7<C ;F*9< <F, *:A7,6< <,:8,9*<?9,
7@ <F, 76=,< *79 <,:8 *< <F, ;-:89,@@-9 76=,<
6+76,@ B7<F
) )
! *6D %
! .?,= @C@<,:@ -8,9*<76+ *<
;-6D7<7-6@ *A->, <F, D,.76,D *=<7<?D, ;*8*A7=7<C D,9*<, .-9
*<:-@8F,97; 89,@@?9, *6D <,:8,9*<?9, ;-6D7<7-6@ -?<@7D, <F, >*=?,@
D,.76,D @,, )
),;F*67;*= +->,96-9 ;-6<9-==,D ?67< 76H,;<-9 ,6+76,@ 9,E?79, *
@,<<76+ ;F*6+, .-9 -8,9*<7-6 *< ;-6D7<7-6@ *A->, <F, *=<7<?D,
D,.76,D -6 <F, ,6+76, 8,9.-9:*6;, @F,,< ,, C-?9 *<,987==*9
<,;F67;*= 9,89,@,6<*<7>, .-9 6-6 @<*6D*9D 9*<76+@
! " ! )"
)
:7@@7-6@ 76.-9:*<7-6 7@ 89,@,6<,D *< L6-:76*=L *6D L"-<,6<7*=
7<, 2*97*<7-6L >*=?,@ .-9 @<*6D*9D 9*<76+@ - <-=,9*6;,@ *9,
*88=7,D <- <F, ,:7@@7-6@ D*<* F,@, >*=?,@ *9, @?AH,;< <- ;F*6+,
*< *6C <7:, F, ;-6<9-==76+ .,D,9*= *6D =-;*= ,:7@@7-6
9,E?79,:,6<@ 6,,D <- A, >,97.7,D AC C-?9 *<,987==*9 <,;F67;*=
9,89,@,6<*<7>,
?@<-:,9L@ :*C F*>, @8,;7*= ,:7@@7-6 @7<, 9,E?79,:,6<@ <F*< 6,,D
<- A, >,97.7,D AC <F, *<,987==*9 "9-D?;< 9-?8 ,6+76,,9
)
)4
C;=, ,:7@@7-6@ )*5 7:7<@ *88=C <- ;C;=, B,7+F<,D *>,9*+,@ -6=C
:7@@7-6@ *< 76D7>7D?*= =-*D 8-76<@ :*C ,5;,,D <F, ;C;=, B,7+F<,D
=7:7<
)
'4
:7@@7-6@ 4 )
)
'
'-9 ;-6@<*6< @8,,D :*976, ,6+76,@ .-9 @F78 :*76 89-8?=@7-6
76;=?D76+D7,@,= ,=,;<97; D97>, <,@< ;C;=,
@F*== A, *88=7,D
.-9 ;-6<9-==*A=, 87<;F 89-8,==,9 @,<@
<,@< ;C;=,
@F*== A, *88=7,D
'-9 89-8,==,9 =*B -8,9*<,D :*76 *6D 89-8,==,9 =*B -8,9*<,D
*?57=7*9C ,6+76,@ <F, <,@< ;C;=,
@F*== A, *88=7,D
'-9 ;-6@<*6< @8,,D *?57=7*9C ,6+76,@ <,@< ;C;=, @F*== A,
*88=7,D
( '-9 >*97*A=, @8,,D >*97*A=, =-*D *?57=7*9C ,6+76,@ 6-<
76;=?D,D *A->, <,@< ;C;=, @F*== A, *88=7,D
%
'4
7,@,= 79;?7< C8, *6D %%2 *=*6;, 4 )
%% "
)
0%1
'4
4
)
'4
+97;?=<?9, 4 )
'79, "?:8 4 )
,6,9*<-9 ,< 4 )
,6,9*<-9 0*@1 4 )(
6D?@<97*= 7,@,= 4 )
6D?@<97*= 0*@1 4 )(
997+*<7-6 4 )(
-;-:-<7>, 4 )
)*976, ?57=7*9C 4 )
)*976, "9-8 0
5;,8< 1 4 )(
)*976, "9-8 0 -6=C1 4 )(
)% 4 )(
7= '7,=D 0",<9-=,?:1 4 )
.. %7+FB*C 9?;G 4 )
6 %7+FB*C 9?;G 4 )
!
'4
-?6D "-B,9 4 )
-?6D "9,@@?9, 4 )
*<, ,=,*@,D 4 &&
"*+, -.
1/21/2020 Package Data Display
Sound Comments :
https://tmiwebclassic.cat.com/tmi/servlet/TMIDirector?Action=openwindow&type=RNTMIRefNum&refno=&selection=&unitType=&system=tmiweb 1/3
1/21/2020 Package Data Display
https://tmiwebclassic.cat.com/tmi/servlet/TMIDirector?Action=openwindow&type=RNTMIRefNum&refno=&selection=&unitType=&system=tmiweb 2/3
1/21/2020 Package Data Display
375.0 75.0 65.5 81.2 72.6 72.5 60.1 56.7 51.0 46.8 52.9
250.0 50.0 64.6 79.2 71.1 71.9 59.6 55.7 49.4 45.1 49.0
125.0 25.0 63.9 77.4 70.2 70.5 59.2 55.4 48.7 44.0 43.6
https://tmiwebclassic.cat.com/tmi/servlet/TMIDirector?Action=openwindow&type=RNTMIRefNum&refno=&selection=&unitType=&system=tmiweb 3/3
1/22/2020 Caterpillar Generator Data
G D J 22, 2020
For Help Desk Phone Numbers Click here
Selected Model
Engine: C15 Generator Frame: M3154L4 Genset Rating (kW): 500.0 Line Voltage: 480
Fuel: Diesel Generator Arrangement: 5652331 Genset Rating (kVA): 625.0 Phase Voltage: 277
Frequency: 60 Excitation Type: Self Excited Pwr. Factor: 0.8 Rated Current: 751.8
Duty: STANDBY Connection: - STAR Application: EPG Status: Current
Version: 42423 /43607 /43655 /8556
Spec Information
Generator Specification
Generator Efficiency
Frame: M3154L4 Type: SR500 No. of Bearings: 1
Per Unit Load kW Efficiency %
Winding Type: RANDOM WOUND Flywheel: 14.0
0.25 125.0 93.3
Connection: - STAR Housing: 1
0.5 250.0 95.2
Phases: 3 No. of Leads: 6
0.75 375.0 95.4
Poles: 4 Wires per Lead: 0
1.0 500.0 95.1
Sync Speed: 1800 Generator Pitch: 0.6667
Short Circuit Ratio: 0.4 Stator Resistance = 0.0087 Ohms Field Resistance = 0.5791 Ohms
Voltage Regulation Generator Excitation
Voltage level adjustment: +/- 5.0% No Load Full Load, (rated) pf
Voltage regulation, steady state: +/- 1.0% Series Parallel
Voltage regulation with 3% speed change: +/- 1.0% Excitation voltage: 10.64 Volts 46.58 Volts Volts
Waveform deviation line - line, no load: less than 2.0% Excitation current 1.0 Amps 3.6 Amps Amps
Telephone influence factor: less than 50
https://tmiwebclassic.cat.com/tmi/servlet/TMIDirector?Action=openwindow&log=genXmlData&type=RNGenDataRefNum&refno=&selection=&unitType… 1/9
1/22/2020 Caterpillar Generator Data
Selected Model
Engine: C15 Generator Frame: M3154L4 Genset Rating (kW): 500.0 Line Voltage: 480
Fuel: Diesel Generator Arrangement: 5652331 Genset Rating (kVA): 625.0 Phase Voltage: 277
Frequency: 60 Excitation Type: Self Excited Pwr. Factor: 0.8 Rated Current: 751.8
Duty: STANDBY Connection: - STAR Application: EPG Status: Current
Version: 42423 /43607 /43655 /8556
Selected Model
Engine: C15 Generator Frame: M3154L4 Genset Rating (kW): 500.0 Line Voltage: 480
Fuel: Diesel Generator Arrangement: 5652331 Genset Rating (kVA): 625.0 Phase Voltage: 277
Frequency: 60 Excitation Type: Self Excited Pwr. Factor: 0.8 Rated Current: 751.8
Duty: STANDBY Connection: - STAR Application: EPG Status: Current
Version: 42423 /43607 /43655 /8556
https://tmiwebclassic.cat.com/tmi/servlet/TMIDirector?Action=openwindow&log=genXmlData&type=RNGenDataRefNum&refno=&selection=&unitType… 2/9
1/22/2020 Caterpillar Generator Data
Selected Model
Engine: C15 Generator Frame: M3154L4 Genset Rating (kW): 500.0 Line Voltage: 480
Fuel: Diesel Generator Arrangement: 5652331 Genset Rating (kVA): 625.0 Phase Voltage: 277
Frequency: 60 Excitation Type: Self Excited Pwr. Factor: 0.8 Rated Current: 751.8
Duty: STANDBY Connection: - STAR Application: EPG Status: Current
Version: 42423 /43607 /43655 /8556
Percent
SKVA
Volt Dip
61 2.5
125 5.0
193 7.5
264 10.0
340 12.5
420 15.0
504 17.5
594 20.0
690 22.5
793 25.0
902 27.5
1,019 30.0
1,145 32.5
1,280 35.0
1,427 37.5
1,585 40.0
https://tmiwebclassic.cat.com/tmi/servlet/TMIDirector?Action=openwindow&log=genXmlData&type=RNGenDataRefNum&refno=&selection=&unitType… 3/9
1/22/2020 Caterpillar Generator Data
Current Decrement Data
E Time
AMP
Cycle
0.0 6,441
1.0 4,242
2.0 3,372
3.0 2,821
4.0 2,385
5.0 2,017
7.5 1,316
10.0 845
12.5 529
15.0 346
20.0 190
25.0 135
30.0 115
35.0 106
40.0 102
45.0 101
Instantaneous 3 Phase Fault Current: 6441 Amps Instantaneous Line - Line Fault Current: 5126 Amps
Instantaneous Line - Neutral Fault Current: 8645 Amps
Selected Model
Engine: C15 Generator Frame: M3154L4 Genset Rating (kW): 500.0 Line Voltage: 480
Fuel: Diesel Generator Arrangement: 5652331 Genset Rating (kVA): 625.0 Phase Voltage: 277
Frequency: 60 Excitation Type: Self Excited Pwr. Factor: 0.8 Rated Current: 751.8
Duty: STANDBY Connection: - STAR Application: EPG Status: Current
Version: 42423 /43607 /43655 /8556
Field Line -
Current Line Volt
0.0 0
12.7 288
14.8 336
17.0 384
19.2 432
21.5 480
23.9 528
26.6 576
29.6 624
33.3 672
https://tmiwebclassic.cat.com/tmi/servlet/TMIDirector?Action=openwindow&log=genXmlData&type=RNGenDataRefNum&refno=&selection=&unitType… 4/9
1/22/2020 Caterpillar Generator Data
Short Circuit Curve
Field Armature
Current Current
0.0 0
37.2 451
43.3 526
49.5 601
55.7 677
61.9 752
68.1 827
74.3 902
80.5 977
86.7 1,052
Selected Model
Engine: C15 Generator Frame: M3154L4 Genset Rating (kW): 500.0 Line Voltage: 480
Fuel: Diesel Generator Arrangement: 5652331 Genset Rating (kVA): 625.0 Phase Voltage: 277
Frequency: 60 Excitation Type: Self Excited Pwr. Factor: 0.8 Rated Current: 751.8
Duty: STANDBY Connection: - STAR Application: EPG Status: Current
Version: 42423 /43607 /43655 /8556
Field Line -
Current Line Volt
61.9 0
75.5 240
77.7 288
79.9 336
82.2 384
84.6 432
87.2 480
90.0 528
93.4 576
97.7 624
https://tmiwebclassic.cat.com/tmi/servlet/TMIDirector?Action=openwindow&log=genXmlData&type=RNGenDataRefNum&refno=&selection=&unitType… 5/9
1/22/2020 Caterpillar Generator Data
Air Gap Curve
Field Line -
Current Line Volt
0.0 0
12.6 288
14.7 336
16.8 384
18.9 432
21.1 480
23.2 528
25.3 576
27.4 624
29.5 672
Selected Model
Engine: C15 Generator Frame: M3154L4 Genset Rating (kW): 500.0 Line Voltage: 480
Fuel: Diesel Generator Arrangement: 5652331 Genset Rating (kVA): 625.0 Phase Voltage: 277
Frequency: 60 Excitation Type: Self Excited Pwr. Factor: 0.8 Rated Current: 751.8
Duty: STANDBY Connection: - STAR Application: EPG Status: Current
Version: 42423 /43607 /43655 /8556
https://tmiwebclassic.cat.com/tmi/servlet/TMIDirector?Action=openwindow&log=genXmlData&type=RNGenDataRefNum&refno=&selection=&unitType… 6/9
1/22/2020 Caterpillar Generator Data
Selected Model
Engine: C15 Generator Frame: M3154L4 Genset Rating (kW): 500.0 Line Voltage: 480
Fuel: Diesel Generator Arrangement: 5652331 Genset Rating (kVA): 625.0 Phase Voltage: 277
Frequency: 60 Excitation Type: Self Excited Pwr. Factor: 0.8 Rated Current: 751.8
Duty: STANDBY Connection: - STAR Application: EPG Status: Current
Version: 42423 /43607 /43655 /8556
https://tmiwebclassic.cat.com/tmi/servlet/TMIDirector?Action=openwindow&log=genXmlData&type=RNGenDataRefNum&refno=&selection=&unitType… 7/9
1/21/2020 TMIWEB Production(a24-tc8-jdk8-tmi-prod)
https://tmiwebclassic.cat.com/tmi/servlet/TMIDirector?Action=openwindow&type=RNTMIRefNum&refno=&selection=&unitType=&system=tmiweb 1/2
1/21/2020 TMIWEB Production(a24-tc8-jdk8-tmi-prod)
MOUNTING SYSTEM
CENTER OF GRAVITY LOCATION - X DIMENSION - FROM REAR
22.2 IN
FACE OF BLOCK - (REFERENCE TM7077)
CENTER OF GRAVITY LOCATION - Y DIMENSION - FROM
9.4 IN
CENTERLINE OF CRANKSHAFT - (REFERENCE TM7077)
CENTER OF GRAVITY LOCATION - Z DIMENSION - FROM
0 IN
CENTERLINE OF CRANKSHAFT - (REFERENCE TM7077)
STARTING SYSTEM
MINIMUM CRANKING SPEED REQUIRED FOR START 115 RPM
LOWEST AMBIENT START TEMPERATURE WITHOUT AIDS 32 DEG F
https://tmiwebclassic.cat.com/tmi/servlet/TMIDirector?Action=openwindow&type=RNTMIRefNum&refno=&selection=&unitType=&system=tmiweb 2/2
AUTOMATIC VOLTAGE REGULATOR
D350 AVR
The D350, Digital Voltage Regulator is used to regulate
alternators with a field current of less than 5 A in continuous
operations, and 10 A maximum in the event of short-circuit
for 10 seconds maximum.
LEHE1923-00
AUTOMATIC VOLTAGE REGULATOR
Technical characteristics
D350 regulator can be used to perform the following functions:
Voltage regulation
• With or without reactive droop compensation (Reactive droop to allow parallel operation)
• With or without line droop compensation.
Regulation of the field current, or manual mode, which allows direct control of the field current.
• Adjust the reference for the regulation mode in progress, using an analogue input (0-10V
• and potentiometer)
• Monitoring of temperature sensor (Pt100 or CTP)
• Limit the minimum field current delivered to the exciter field
• Monitoring of the maximum stator current limit
• Loss of voltage sensing
• Withstand a sudden short-circuit for 10 seconds maximum in AREP, PMG
• Signals monitoring (events logger).
• 2 digital outputs for various trip, regulation mode and measurement data
Power supply:
• 4 terminals for PMG, AREP, SHUNT
• Range 50-277 VAC
• Consumption max < 3000VA
Field excitation:
• Rated 0-5 A
• Short-circuit 10A max.
• Field winding resistance > 4 ohms
Frequency:
• Range 10-100Hz
LEHE1923-00
AUTOMATIC VOLTAGE REGULATOR
• Regulation accuracy: +/-0.25% of the average of the three phases on a linear load, with
harmonic distortion less than 5%
• Voltage adjustment range: 0 to 150% of the rated voltage
• Quadrature droop adjustment range: -20% to 20%
• Under frequency protection: integrated, adjustable threshold, slope adjustable from 0.5 to
3V/Hz in steps of 0.1 V/Hz
• Excitation ceiling: adjustable by configuration at 3 points
• Environment: ambient temperature from -40°C to +65°C, relative humidity of less than 95%
non-condensing, mounted in a cabinet or in a terminal box
Dimensions:
• Height : 52.9mm
• width : 125mm
• Length : 140mm
Mounting:
• Holes spacing on the Length : 115mm
• Holes spacing on the width: 100mm
Weight: 0.45kg
Conformity to standards
• EMC: IEC 61000-6-2, IEC 61000-6-4
• Humidity: IEC 60068-1 and test in accordance with IEC 60068-2-14
• Dry heat: IEC 60068-2-2
• Damp heat: IEC 60028-2-30
• Cold: IEC 600068-2-1
LEHE1923-00
AUTOMATIC VOLTAGE REGULATOR
D350 AVR and NFLink™ Dimensions
LEHE1923-00 (05-19)
www.Cat.com/electricpower
©2019 Caterpillar All rights reserved. Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication. CAT, CATERPILLAR, their respective logos,
“Caterpillar Yellow”, the “Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
Circuit Breakers
C9 ACERT TM, C13 ACERT, C15 ACERT,
C18 ACERT Circuit Breakers
Manually Operated Circuit Breakers
Current Fram e Num ber Interrupting Ratings (kA rm s)
(A) of Poles Trip (Lugs) Cable Size
Auxiliary Options
240V 480V 600V Units Range / Phase
BUS BAR
3000 R 3 65 35 18
LEHE0942-05 1/17
Circuit Breakers
Single Breaker Options (250 – 3000A)
Model Current (A) Operation
C9 ACERT, C13 ACERT, C15 ACERT, C18 ACERT 600 Manually Operated
C9 ACERT, C13 ACERT, C15 ACERT, C18 ACERT 800 Manually Operated or Electrically Operated
C9 ACERT, C13 ACERT, C15 ACERT, C18 ACERT 1200 Manually Operated or Electrically Operated
C9 ACERT, C13 ACERT, C15 ACERT, C18 ACERT 250 250, 400, 600,
800, or 1200 3rd Breaker:
C9 ACERT, C13 ACERT, C15 ACERT, C18 ACERT 400
250 or 400 (Not
C9 ACERT, C13 ACERT, C15 ACERT, C18 ACERT 600
available if
C9 ACERT, C13 ACERT, C15 ACERT, C18 ACERT 800 1st & 2nd Breaker =
1200A)
C9 ACERT, C13 ACERT, C15 ACERT, C18 ACERT 1200
LEHE0942-05 2/17
Circuit Breakers
L EHE0942-05 3/17
Circuit Breakers
L EHE0942-05 4/17
Circuit Breakers
J-Frame 250 A Typical Peak Let-Through Curves
Figure 1
LEHE0942-05 5/17
Circuit Breakers
J-Frame 150-250 A (JD, JG, JJ, JL, and JR) Thermal-Magnetic
Trip
Figure 2
LEHE0942-05 6/17
Circuit Breakers
Ground Fault Module GFM250JD Trip Curve
Figure 3
LEHE0942-05 7/17
Circuit Breakers
T6 600 / 800 -PR221DS
LEHE0942-05 8/17
Circuit Breakers
T6 600 / 800 -PR221DS
LEHE0942-05 9/17
Circuit Breakers
Tmax T7 PR231/P Functions
L-S Functions
Figure 7
LEHE0942-05 10/17
Circuit Breakers
T6 800 - PR222DS and PR222DS/PD-A
LEHE0942-05 11/17
Circuit Breakers
T7 1000/1200 - PR232/P
Figure 9
LEHE0942-05 12/17
Circuit Breakers
T7 1000/1200 - PR332/P
L-S-I Functions
Figure 10
LEHE0942-05 13/17
Circuit Breakers
T8 1600/2000/2500/3000 – PR232/P-T8
L-S-I Functions
Figure - 11
LEHE0942-05 14/17
Circuit Breakers
P, R, NS-Frame Long-Short Trip Curve and NW-Frame Long-
Short Trip Curve
Figure - 12
LEHE0942-05 15/17
Circuit Breakers
P, R, NS-Frame Instant Curve and NW-Frame Instant Trip Curve
Figure 13
LEHE0942-05 16/17
Circuit Breakers
P, R, NS-Frame Ground Curve and NW-Frame Ground Fault Trip Curve
Figure - 14
LEHE0942-05 (10-19)
www.Ca t.com/electricpower
©2019 Caterpillar. All rights reserved. Materials and specifications are subject to change without notice. CAT, CATERPILLAR, their respective logos, ADEM, S•O•S, LET’S DO THE WORK, “Caterpillar Yellow”,
the “Power Edge” trade dress as well ascorporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
17/17
Note : The Information on this Document comesfroma Third Party Sup plier and isnot a Caterpillar Material
Attachments
AC SUPPLY
VOLTAGE RANGE 90 V to 305 V (L-N)
FREQUENCY RANGE
48 Hz to 64 Hz (L-N)
DC OUTPUT RATING
10 A DC at 24 V DC
EFFICIENCY
>86%
REGULATION LINE
Image shown might not reflect actual configuration <0.5%
A comprehensive range of input and output protections ensures a continued safe PROTECTIONS
charging environment also enabling the use of the charger as a power supply. Short Circuit
DC Over Voltage
DC Over Current
Reverse Polarity
FEATURES Over Temperature
• Intelligent two, three and four stage charging profiles AC Under & Over Voltage
• Configurable to suit most battery types (12V/24V)
• Adjustable current limit CHARGE FAILURE RELAY
3 A at 30 V DC volt free relay
• Can be used as a battery charger, power supply or both at the same time
• Automatic or Manual boost and storage charge functions to help maintain battery condition
DIMENSIONS OVERALL
• Digital Microprocessor Technology
70 mm x200 mm x 130 mm
• Temperature compensation for battery charging
2.7” x 7.9” x 5.1”
• Low Output Ripple and superb line regulation
• Three LED Indicators WEIGHT
• AC input Under voltage 0.75 kg
• AC input Over voltage
• Battery charger output Over voltage OPERATING TEMPERATURE RANGE
• Battery charger output Over current -30 °C to +80 °C
• Optional battery temperature compensation with over temperature protection -22 °F to +176 °F
• Output short circuit and Inversion polarity with auto recovery
• Configurable charge termination STORAGE TEMPERATURE RANGE
-40 °C to +70 °C
Automatic Boost Mode -22 °F to +158 °F
• Boosts and equalises cell charge improving battery performance and life
Communication
• Can be integrated into external systems through MODBUS RTU using RS485
• Fully configurable via PC Software
• External remote LCD option
BENEFITS
• Fully flexible to maximise the life of the battery
• Suitable for a wide range of battery types
• Switched mode design
BENEFITS
• Minimum 86% efficiency throughout full operating range
• No external intervention for boost mode
• Multiple chargers can be linked together to provide larger current output
• Can be permanently connected to battery and mains (utility) supply. No need to disconnect
through high load conditions.
LEHE2022-01 (09-19)
www.Cat.com/electricpower
©2019 Caterpillar All rights reserved. Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication. CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow”,
the “Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
Attachments
Features
• Uniform heat distribution
• Reduces wear from cold spots
• Improves startability
• Thermostatically controlled and protected
• 6’ (1.8m) cord
• Ensures generator is at optimal starting temperature and ready to accept load
• Durable pump with non-magnetic impeller that does not attract metal debris
• Robust die cast aluminum housing improves sealing of the hoses, eliminates leaking and breakage
• Corrosion resistant steel brackets for superior strength and durability
• Reduces thermal stress on coolant hoses
• Element designed for long life with maximum heat transfer
• IP44 Ingress Protection Rating
• No evaporation of coolant from hoses
• Reduces low coolant level alarms because coolant does not boil
Regulating Safety
Part No Outlet Location Watts Volts Amps Thermostat Thermostat
On 90°F (32°C)
577-1758/577-9355 Right 2700 240 11.25 Off 115°F (46°C) 210°F (98°C)
www.cat.com/electricpower
©2019 Caterpillar
All rights reserved.
Information contained in this publication may be considered confidential. Discretion is recommended when distributing.
Materials and specifications are subject to change without notice.
CAT, CATERPILLAR, LET’S DO THE WORK, their respective logos, “Caterpillar Yellow,” the “Power Edge” and Cat
“Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks
of Caterpillar and may not be used without permission.
LEHE2077-00 (11/19)
100 Amp Load Centre
Specifications
Number of spaces 6
Number of circuits 12
Number of tandem circuit breakers 6
System voltage 120/240VAC
NEMA degree of protection NEMA 3R outdoor
Electrical connection Lugs
Wiring configuration 3-wire
Material Tin plated aluminum busbar
Enclosure material Welded galvannealed steel
Cover finish Gray baked enamel
Product certifications UL E-6294
www.cat.com/electricpower
©2019 Caterpillar
All rights reserved.
Information contained in this publication may be considered confidential. Discretion is recommended when distributing.
Materials and specifications are subject to change without notice.
CAT, CATERPILLAR, LET’S DO THE WORK, their respective logos, “Caterpillar Yellow,” the “Power Edge” and Cat
“Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks
of Caterpillar and may not be used without permission.
LEHE2075-00 (11/19)
Cat GC ®
Control Panel Options
ELECTRO-MAGNETIC COMPATIBILITY
BS EN 61000-6-2
EMC Generic Immunity Standard for the Industrial Environment
BS EN 61000-6-4
EMC Generic Emission Standard for the Industrial Environment
ELECTRICAL SAFETY
BS EN 60950
Safety of Information Technology Equipment, including Electrical
Business Equipment
TEMPERATURE
BS EN 60068-2-1
Ab/Ae Cold Test -30 °C BS EN 60068-2-2
Bb/Be Dry Heat+70°C
VIBRATION
BS EN 60068-2-6
Ten sweeps in each of three major axes
5 Hz to 8 Hz @ +/-7.5 mm, 8 Hz to 500 Hz @ 2 gn
SHOCK
BS EN 60068-2-27
Three shocks in each of three major axes 15 gn in 11 Ms
HUMIDITY
Remote Annunciator Module BS EN 60068-2-30
Db Damp Heat Cyclic 20/55 °C @ 95% RH 48 Hours
It is an LED expansion module that can be used with compatible control BS EN 60068-2-78
Cab Damp Heat Static 40 °C @ 93% RH 48 Hours
modules. The module has been designed to display a maximum of eight
DEGREES OF PROTECTION PROVIDED BY ENCLOSURES BS EN
individual LED indications up to a maximum distance of 1 KM (0.6miles). 60529
IP65 - Front of module when installed into the control panel with the
The Annunciator will consist of two modules to provide a 16 Channel supplied sealing gasket.
Fault annunciation.
It is presented in a vertical enclosure. It includes an alarm sounder that
is triggered when the host controller detects an alarm condition. The CONTINUOUS VOLTAGE RATING
8 V to 35 V Continuous
alarm can be muted using the front push button.
CRANKING DROPOUTS
The Panels will be fitted with removable label cards which can be used Able to survive 0 V for 50 mS, providing supply was at least
10 V before dropout and supply recovers to 5 V. This is
to identify the standard NFPA alarms. If desired achieved without the need for internal batteries. LEDs and
backlight will not be maintained during cranking.
It includes individual LEDs for each channel and a ‘Power On’ LED that
MAXIMUM OPERATING CURRENT
flashes when the link with the host controller is lost. 112 mA at 12 V, 53 mA at 24 V
LEHE2021-00 (08-19)
www.Cat.com/electricpower
©2019 Caterpillar All rights reserved. Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication. CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow”,
the “Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
Cat GC ®
INTEGRAL FUEL TANKS
FEATURES
LEHE2015-00
Cat GC ®
INTEGRAL FUEL TANKS
Integral Fuel Tank Base Useable Capacities with Fuel Tank Dimensions & Weights
Standby Width Width
ekW mm in
250-300 1430 56.3
350-400 1630 64.1
450-500 1630 64.1
550-600 1865 73.4
WIDTH
HEIGHT
LENGTH
The heights listed above do not include lumber used during manufacturing and shipping
Integral FTDW036 2820 744.9 2553 674.4 1165 2568 818.8 32.2 4815 189.5 2584 101.7 2644 104
Tank FTDW037 3671 969.7 3323 877.8 1331 2934 668.2 26.3 4622 181.9 2456 96.7 2644 104
FTDW038 4292 1133.8 3889 1027.3 1657 3653 816.4 32.1 4980 196 2560 100.7 2172 85.5
LEHE2015-00
Cat GC ®
INTEGRAL FUEL TANKS
Tanks with full electrical stub-up area include removable end channel. Tanks with RH stub-up include stubup area directly below the
circuit breaker or power terminal strips.
Fuel tanks and applicable options facilitate compliance with the following United States NFPA Code and Standards:
NFPA 30: Flammable and Combustible Liquids Code
NFPA 37: Standard for the Installation and Use of Stationary Combustion Engines and Gas Turbines
NFPA 110: Standard for Emergency and Standby Power Systems
Fuel tanks and applicable options facilitate compliance with the following Canadian Standard and Code:
CSA C282 – Emergency Electrical Power Supply for Buildings
CSA B139-09 – Installation Code for Oil-Burning Equipment
LEHE2015-00 (07-19)
www.Cat.com/electricpower
©2019 Caterpillar All rights reserved. Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication. CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow”, the
“Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
Cat GC ®
ENCLOSURES
FEATURES
Excellent Access
• Large cable entry area for installation ease.
• Accommodates side mounted single or multiple breakers.
• Two doors on both sides.
• Vertically hinged allow 180° opening rotation
• Radiator fill cover.
LEHE2014-02
Cat GC ®
ENCLOSURES
LEHE2014-02
Cat GC ®
ENCLOSURES
Standby
Length, L Width, W Height, H Package Weights
Enclosure Type Ratings,
ekW mm in mm in mm in kg lb
Sound Attenuated Enclosure on 250 2857 6298.6
3958 155.8 1440 56.7 1991 78.4
Skid Base 300 2945 6492.6
350 3983 8781.0
4633 182.4 1630 64.2 2227 87.7
400 4017 8856.0
450 4408 9718.0
4823 189.8 1630 64.2 2777 109.3
500 4457 9826.0
550 4754 10480.8
4980 196.1 1865 73.4 2723 107.2
600 4837 10663.8
Sound Attenuated Enclosure on 250 3497 7709.6
UL Listed Integral Fuel Tank 3958 155.8 1440 56.7 2487 97.9
300 3585 7903.6
Base 350 4765 10505.0
4633 182.4 1630 64.2 2644 104.1
400 4799 10580.0
450 5345 11783.7
4823 189.8 1630 64.2 2777 109.3
500 5394 11891.7
550 5973 13168.2
4980 196.1 1865 73.4 2723 107.2
600 6056 13351.2
LEHE2014-02 (09-19)
www.Cat.com/electricpower
©2019 Caterpillar All rights reserved. Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication. CAT, CATERPILLAR, their respective logos,
“Caterpillar Yellow”, the “Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
L L
6310 CONTROLLER
J J
I I
H H
B B
M
A
T
NOTE A: FACTORY WIRING NOT PROVIDED AS STANDARD. REFER TO MANUFACTURER INSTALLATION INSTRUCTIONS. L
HT
TR
DIAGRAM-WIRING
(C9-C18) (DSE6310)
VER CHG
569-6011 2X3
- 02
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
L
CONTROL SCHEMATIC (DSE 6310) L
ADEM A4:E4
A-C3
ECM 160-7689
23 ECU + (J1939)
A-S3
24 ECU - (J1939)
A-S4 CAN+
J1-PIN34 CAN A- 34 Y798-A3 WH-18 A-T13
1 1
120R
CBL-A2:Y798-A1 BK-18 A-T14 1 1
CAN-
Resistor_As_3_Nodes_1 A-T15
1 1 A-T17
134-2540 A-C2
155-2267
J J
A Y797-A20 WH-18 A-C1
265-4123
B Y798-A44 WH-18
CBL-A4:Y798-A1 BK-18 F
C REF [16,F] 208-A22 WH-18 A-T61
1 DC SUPPLY (-)
120 CBL-A4:Y797-A2 WH-18 G
ENGINE SERVICE E-STOP_PANEL REF [10,D] 108-A25 WH-18 A-T62
DC SUPPLY (+)
2
CBL-A4:Y799-A3 CU-20 C CONNECTOR 390--1209
J 22 21
A-T20 A-T22
8 OUTPUT D (SPARE)
A-T7
12 OUTPUT H (SPARE)
CUSTOMER TERMINALS
A-S2
1 1
A-T4
G-T
1
1 1
18 ANALOG INPUT C (SPARE)
F4 SPARE ANALOG INPUT
208-A19 BK-8 422-6095 1 1 (NOTE A) 19 ANALOG INPUT D (SPARE)
BATT+
10A
A-S6
26 DSENET B
REF [3,J] 108-A25 WH-18 EXPANSION DATALINK 27 DSENET A
(NOTE A) 28 DSENET SCR
REF [7,I] 108-A55 WH-18
ALT
A-T41
B+ A-T40
101-A43 WH-10
A A 108-A6 WH-18
B B 208-A18 WH-18 REF [15,G]
C C Y983-A5 WH-18 REF [5,F]
M
A
A-C8 T
L
FUEL LEVEL SENSOR 247-8195 HT
TR
1 1 1E5167A INT-PROP
1E0198W BRAND MARKINGS
1E0013Y CONFIDENTIALITY
2 2 P733-A60 WH-18 REF [9,G] 1E0012A INTERPRETATION
N
O 1E0011 INTPR & TOL
3 3 229-A58 WH-18 REF [5,E] T
E Caterpillar: Confidential Yellow
PROD X OTHER
UNLESS OTHERWISE SPECIFIED VERSION PRIMARY X
A DIMENSIONS ARE IN mm
DIMENSIONS W/O TOL ARE BASIC TYPE SECONDARY A
THIRD ANGLE SHEET 2 OF 6
PROJECTION
DWG CONTROL W591
DIAGRAM-WIRING
(C9-C18) (DSE6310)
VER CHG
569-6011 - 2X3
02
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
L
POWER SCHEMATIC L
CB SHUNT TRIP
STR
352--2951
21 24
22
11 14
A-T70
12
3 PHASE STAR
(6 WIRE) 1200A HARNESS
C2 C1
L1 (U)
L2 (V)
UF-T2
P854-A62 WH-18
K CB1_Y0 CB1_ST+ K
T2
UG-T2
T1
EXCITER
UH-T2
T5
VF-T2
CB2_Y0 CB2_ST-
T4
VG-T2
T6
VH-T2
CONNECT TO CONNECT TO
ALTERNATOR
WF-T2
BREAKER
WG-T2
J T3 J
NF-T2
N-NF1 BK-0
NF-T1
L3 (W) NG-T2
N-NG1 BK-0
NG-T1
NH-T2
OPTIONAL OPTIONAL
N-NH1 BK-0
NH-T1
41 95
41-AX1 WH-16 AX-T7
1 1 95-BK ABB-T21
1 1
44
1
98
1
98
1
UNTRIPPED CB TRIPPED/
(12 WIRE) 44-AX2 WH-16 1 1 98-BK 1 1
AX-T1 AX-T6 ABB-T30 ABB-T25
(SY) 41 UNTRIPPED 95
UC-T1
EXCITER T1 T8
VC-T1
11 11
11-AX4 WH-16 AX-T2
1 1 11-BK ABB-T24
1 1
T10 T5
VE-T1
CONNECT TO CONNECT TO 1 1 1 1
14 14 14 14
CB OPEN/CLOSED
T4 T11 ALTERNATOR WC-T1
T12 T6
12 12 12 12
12-AX6 WH-16 AX-T3
1 1 12-BK ABB-T26
1 1
NC-T1
NE-T1
E T9 T3
H H
L3 (W)
400A HARNESS
1 2
L1-UA1 BK-0 UA-T14
L1
A-T42
A-T43
G G
SERIES STAR 1 2
L2-VA1 BK-0 VA-T2
L2 CUSTOMER LOAD
A-T44
A-T45
(12 WIRE)
1 2
L3-WA1 BK-0 WA-T1
L3
A-T49
A-T46
A-T47
UA-
T6
T2
VA-
T4
A-T50
T1 T5
EXCITER
5+ T4
T8 N-NA1 BK-0 NA-T3
N
T7 T11
E494-A36 WH-18
E495-A35 WH-18
E496-A34 WH-18
E498-A37 WH-18
E498-A38 WH-18
E498-A39 WH-18
200-A63 GN-YL-16 A-T65
F T10
NA-T5
F
A-T
51
T12
GENERATOR GROUND
-6 T9 6310 CONTROLLER
200-A61 GN-YL-16 A-T75
T6
E 41 N/C
T3
CONTROL PANEL DOOR GROUND
E498-A33 WH-16 40 CURRENT SENSING COMMON
A-S1
WA-T3
A-T30
A-T48
39 CURRENT SENSING L3
E E
E495-A35 WH-18 A-T32
38 CURRENT SENSING L2
NE LINK CABLE
E494-A36 WH-18 A-T33
37 CURRENT SENSING L1
F1
GN/YL GN/YL 7W-0482
E486-A66 WH-18
A-T57
29 VOLTAGE SENSING L1
30 VOLTAGE SENSING L2
D D
BASEFRAME
F3
GROUND 7W-0482
31 VOLTAGE SENSING L3
32 VOLTAGE SENSING N
C C
STANDARD
SHUNT EXCITATION
D350 AVR
6- 3 F-
0V
5+ 6 F+
AI1
CONNECT TO T7 9 4 X1
0V
B CONNECT TO T12 10 2 X2 B
RTD
5 Z1
0V
1 Z2
DI1
0V M
A
T
L
D02 HT
TR
D01
1E5167A INT-PROP
1E0198W BRAND MARKINGS
1E0013Y CONFIDENTIALITY
1E0012A INTERPRETATION
N
O 1E0011 INTPR & TOL
CONNECT TO T1 U 1 U T
E Caterpillar: Confidential Yellow
PROD X OTHER
CONNECT TO T2 V 2 V S1
UNLESS OTHERWISE SPECIFIED VERSION PRIMARY
A DIMENSIONS ARE IN mm
DIMENSIONS W/O TOL ARE BASIC TYPE SECONDARY A
SHEET 3 OF 6
CONNECT TO T3 W 3 W S2
THIRD ANGLE
PROJECTION
DWG CONTROL W591
DIAGRAM-WIRING
(C9-C18) (DSE6310)
VER CHG
569-6011 - 2X3
02
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
L L
ADDITIONAL OPTIONS
OPTIONAL
VFC FOR GENSET RUNNING AND GENERAL FAULT
K K
14 11
12
24 21
22
I I
OPTIONAL
REMOTE ANNUNCIATOR
2548 CONTROLLER
G G
120R
2548 CONTROLLER
BATT+
1 1
F F
1 1
AN-T7
CUSTOMER CONNECTIONS: 1 1
AN-T8
TO BE CONNECTED IN SERIES 1 1
AN-T9
1 1
AN-T10
E E
D D
C C
B B
M
A
T
L
HT
TR
1E5167A INT-PROP
1E0198W BRAND MARKINGS
1E0013Y CONFIDENTIALITY
1E0012A INTERPRETATION
N
O 1E0011 INTPR & TOL
T
E Caterpillar: Confidential Yellow
PROD X OTHER
UNLESS OTHERWISE SPECIFIED VERSION PRIMARY
A DIMENSIONS ARE IN mm
DIMENSIONS W/O TOL ARE BASIC TYPE SECONDARY A
THIRD ANGLE SHEET 4 OF 6
PROJECTION
DWG CONTROL W591
DIAGRAM-WIRING
(C9-C18) (DSE6310)
VER CHG
569-6011 - 2X3
02
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
L L
ADDITIONAL OPTIONS
OPTIONAL
ALTERNATOR HEATER
AHR
352-2951
K K
REF [16,I] 208-RC36 WH-18 RC-T2 RC-T1
11 14
1 AH_L1 12
RC-T10
AC719-RC39 WH-18 RC-T5
6A CF-T4
AC104-CF2 WH-14
1 1
2
F8
1 1 190-2558
AH_L2
HTR-H2 1 1 RC-T13
AC720-RC40 WH-18 RC-T6
6A CF-T3
AC103-CF1 WH-14
J J
OPTIONAL
BATTERY CHARGER
1 1 572-0792
BATTERY_CHARGER
BATT+
1 1 ER-T13
108-ER1 WH-14 ER-T1
OP+
1 1 ER-T12
208-ER2 WH-14 ER-T2
OP-
I BATT- I
REF [16,K] 208-RC36 WH-18 RC-T4
1 1
NC
COM
NO
NTC
NTC_1
6310 CONTROLLER
120R
8 OUTPUT D (GENSET RUNNING) RC-T3
A309-RC35 WH-18 REF [13,K] LK1
H NOTE C LK1_1 H
26 DSENET B ER-T16
CBL-ER1:B-1 GN-18 ER-T6
B
27 DSENET A ER-T17
CBL-ER1:A-2 YL-18 ER-T7
A
28 DSENET SCR ER-T18
CBL-ER1:SCR-3 CU-18 ER-T8
SCR
GND_1
AC199-ER45 WH-14 ER-T20
N
1 1 F9 AC102-ER44 WH-14 ER-T21
L
GND 422-6095
G 200-CE3 GN-YL-14 CE-T8
1 1 ER-T26
G
ER-T23
10A ER-T22
1 1
1 1
BC_L1
AC101-CE1 WH-14 CE-T6
1 1 ER-T24
AC101-ER43 WH-14
F F
E OPTIONAL E
LOAD CENTER BOX
CE-T13
CD-T3
NEUTRAL
BATT_CHRG_BREAKER
508-6697
20A CE-T18
AC101-CE1 WH-14
ALT_HTRG_BREAKER
577-8557
AC103-CF1 WH-14
L1 CF-T2
CUSTOMER 15A
CF-T1
AC104-CF2 WH-14
D CONNECTION GFCI_RECEPTACLE D
240V 3WIRES 423-7031
GFCI_BREAKER
508-6697
BK (LINE)
L2 20A CD-T2
AC101-CD1 WH-12 CD-T4
WH (N) CD-T5
AC199-CD3 WH-12 REF [14,E]
JWH_BREAKER
577-8557
CONNECT
JACKET WATER GND
CD-T6
15A
HEATER WIRES
200-CE3 GN-YL-14 200-CD2 GN-YL-10
CE-T11
CD-T1
C C
200-CD4 GN-YL-10
CD-T7
MAIN CUSTOMER
GROUND
B B
M
A
T
L
HT
TR
1E5167A INT-PROP
1E0198W BRAND MARKINGS
1E0013Y CONFIDENTIALITY
1E0012A INTERPRETATION
N
O 1E0011 INTPR & TOL
T
E Caterpillar: Confidential Yellow
PROD X OTHER
UNLESS OTHERWISE SPECIFIED VERSION PRIMARY
A DIMENSIONS ARE IN mm
DIMENSIONS W/O TOL ARE BASIC TYPE SECONDARY A
THIRD ANGLE SHEET 5 OF 6
PROJECTION
DWG CONTROL W591
DIAGRAM-WIRING
(C9-C18) (DSE6310)
VER CHG
569-6011 - 2X3
02
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
DC FUSES
J J
GROUND FAULT
REM_STRT
CLN_GND
ESTOP_A
ESTOP_B
CAN_SH
BATT +
BATT +
CB2_95
CB2_96
CB2_98
BATT -
BATT -
BATT -
CB1_14
CB2_11
CB2_12
CB2_14
CB1_11
CB1_12
CB1_95
CB1_41
CB1_96
CB1_42
CB1_98
CB1_44
CAN +
CAN -
C1 C1 C2 C2
I I
H H
F F
D D
F7 F8 F9
AHR
BC_L1
AH_L1
AH_L2
BC_N
GND
C C
B COMPONENT DESCRIPTION B
AHR ALTERNATOR SPACE HEATER RELAY
AH_L1 ALTERNATOR HEATER AC SUPPLY L1
AH_L2 ALTERNATOR HEATER AC SUPPLY L2
F7 ALTERNATOR HEATER FUSE L1 (6A)
F8 ALTERNATOR HEATER FUSE L2 (6A) M
A
GND SHORE POWER GROUND T
L
HT
F9 BATTERY CHARGR FUSE L1 (10A) TR
A DIMENSIONS ARE IN mm
DIMENSIONS W/O TOL ARE BASIC TYPE SECONDARY A
THIRD ANGLE SHEET 6 OF 6
PROJECTION
DWG CONTROL W591
DIAGRAM-WIRING
(C9-C18) (DSE6310)
VER CHG
569-6011 - 2X3
02
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Effective with sales to the first user on or after August 1, 2016
SELF5709
This warranty covers every major component of the products. Claims under this warranty should be submitted to a CATERPILLAR EXCLUDES ALL LIABILITY FOR OR ARISING FROM ANY NEGLIGENCE ON ITS PART
place of business of a Cat dealer or other source approved by Caterpillar. For further information concerning either OR ON THE PART OF ANY OF ITS EMPLOYEES, AGENTS OR REPRESENTATIVES IN RESPECT OF THE
the location to submit claims or Caterpillar as the issuer of this warranty, write Caterpillar Inc., 100 N. E. Adams St., MANUFACTURE OR SUPPLY OF GOODS OR THE PROVISION OF SERVICES RELATING TO THE GOODS.
Peoria, IL USA 61629.
CATERPILLAR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES UNLESS IMPOSED UNDER
Caterpillar’s obligations under this Limited Warranty are subject to, and shall not apply in contravention of, the laws, MANDATORY RIGHTS.
rules, regulations, directives, ordinances, orders, or statutes of the United States, or of any other applicable jurisdiction,
IF OTHERWISE APPLICABLE, THE VIENNA CONVENTION ON CONTRACTS FOR THE INTERNATIONAL SALE
without recourse or liability with respect to Caterpillar.
OF GOODS IS EXCLUDED IN ITS ENTIRETY.
A) For products operating outside of Australia, Fiji, Nauru, New Caledonia, New Zealand, Papua New Guinea, the
C) For products supplied in Australia:
Solomon Islands and Tahiti, the following is applicable:
IF THE PRODUCTS TO WHICH THIS WARRANTY APPLIES ARE:
NEITHER THE FOREGOING EXPRESS WARRANTY NOR ANY OTHER WARRANTY BY CATERPILLAR,
EXPRESS OR IMPLIED, IS APPLICABLE TO ANY ITEM CATERPILLAR SELLS THAT IS WARRANTED DIRECTLY I. PRODUCTS OF A KIND ORDINARILY ACQUIRED FOR PERSONAL, DOMESTIC OR HOUSEHOLD USE
TO THE USER BY ITS MANUFACTURER. OR CONSUMPTION; OR
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, II. PRODUCTS THAT COST AUD 40,000 OR LESS,
INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
EXCEPT CATERPILLAR EMISSION-RELATED COMPONENTS WARRANTIES FOR NEW ENGINES, WHERE WHERE THOSE PRODUCTS WERE NOT ACQUIRED FOR THE PURPOSE OF RE-SUPPLY OR FOR THE
APPLICABLE. REMEDIES UNDER THIS WARRANTY ARE LIMITED TO THE PROVISION OF MATERIAL AND PURPOSE OF USING THEM UP OR TRANSFORMING THEM IN THE COURSE OF PRODUCTION OR
SERVICES, AS SPECIFIED HEREIN. MANUFACTURE OR IN THE COURSE OF REPAIRING OTHER GOODS OR FIXTURES, THEN THIS SECTION
C APPLIES.
CATERPILLAR IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
THE FOLLOWING MANDATORY TEXT IS INCLUDED PURSUANT TO THE AUSTRALIAN CONSUMER LAW
CATERPILLAR EXCLUDES ALL LIABILITY FOR OR ARISING FROM ANY NEGLIGENCE ON ITS PART AND INCLUDES REFERENCES TO RIGHTS THE USER MAY HAVE AGAINST THE DIRECT SUPPLIER OF
OR ON THE PART OF ANY OF ITS EMPLOYEES, AGENTS OR REPRESENTATIVES IN RESPECT OF THE THE PRODUCTS: OUR GOODS COME WITH GUARANTEES THAT CANNOT BE EXCLUDED UNDER THE
MANUFACTURE OR SUPPLY OF GOODS OR THE PROVISION OF SERVICES RELATING TO THE GOODS. AUSTRALIAN CONSUMER LAW. YOU ARE ENTITLED TO A REPLACEMENT OR REFUND FOR A MAJOR
FAILURE AND COMPENSATION FOR ANY OTHER REASONABLY FORESEEABLE LOSS OR DAMAGE. YOU
IF OTHERWISE APPLICABLE, THE VIENNA CONVENTION ON CONTRACTS FOR THE INTERNATIONAL SALE
ARE ALSO ENTITLED TO HAVE THE GOODS REPAIRED OR REPLACED IF THE GOODS FAIL TO BE OF
OF GOODS IS EXCLUDED IN ITS ENTIRETY.
ACCEPTABLE QUALITY AND THE FAILURE DOES NOT AMOUNT TO A MAJOR FAILURE. THE INCLUSION
For personal or family use engines or electric power generation products, operating in the USA, its territories and OF THIS TEXT DOES NOT CONSTITUTE ANY REPRESENTATION OR ACCEPTANCE BY CATERPILLAR OF
possessions, some states do not allow limitations on how long an implied warranty may last nor allow the exclusion LIABILITY TO THE USER OR ANY OTHER PERSON IN ADDITION TO THAT WHICH CATERPILLAR MAY HAVE
or limitation of incidental or consequential damages. Therefore, the previously expressed exclusion may not apply to UNDER THE AUSTRALIAN CONSUMER LAW.
you. This warranty gives you specific legal rights and you may also have other rights, which vary by jurisdiction. To
TO THE EXTENT THE PRODUCTS FALL WITHIN THIS SECTION C BUT ARE NOT OF A KIND ORDINARILY
find the location of the nearest Cat dealer or other authorized repair facility, call (800) 447-4986. If you have questions
ACQUIRED FOR PERSONAL, DOMESTIC OR HOUSEHOLD USE OR CONSUMPTION, CATERPILLAR LIMITS
concerning this warranty or its applications, call or write:
ITS LIABILITY TO THE EXTENT IT IS PERMITTED TO DO SO UNDER THE AUSTRALIAN CONSUMER LAW
In USA and Canada: Caterpillar Inc., Engine Division, P. O. Box 610, Mossville, IL 61552-0610, Attention: Customer TO, AT ITS OPTION, THE REPAIR OR REPLACEMENT OF THE PRODUCTS, THE SUPPLY OF EQUIVALENT
Service Manager, Telephone (800) 447-4986. Outside the USA and Canada: Contact your Cat dealer. PRODUCTS, OR THE PAYMENT OF THE COST OF SUCH REPAIR OR REPLACEMENT OR THE ACQUISITION
OF EQUIVALENT PRODUCTS.
B) For products operating in Australia, Fiji, Nauru, New Caledonia, New Zealand, Papua New Guinea, the Solomon
Islands and Tahiti, the following is applicable: THE WARRANTY SET OUT IN THIS DOCUMENT IS GIVEN BY CATERPILLAR INC. OR ANY OF ITS
SUBSIDIARIES, 100 N. E. ADAMS ST, PEORIA, IL USA 61629, TELEPHONE 1 309 675 1000, THE USER IS
THIS WARRANTY IS IN ADDITION TO WARRANTIES AND CONDITIONS IMPLIED BY STATUTE AND OTHER RESPONSIBLE FOR ALL COSTS ASSOCIATED WITH MAKING A CLAIM UNDER THE WARRANTY SET
STATUTORY RIGHTS AND OBLIGATIONS THAT BY ANY APPLICABLE LAW CANNOT BE EXCLUDED, OUT IN THIS DOCUMENT, EXCEPT AS EXPRESSLY STATED OTHERWISE IN THIS DOCUMENT, AND THE
RESTRICTED OR MODIFIED (“MANDATORY RIGHTS”). ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS USER IS REFERRED TO THE BALANCE OF THE DOCUMENT TERMS CONCERNING CLAIM PROCEDURES,
OR IMPLIED (BY STATUTE OR OTHERWISE), ARE EXCLUDED. WITHOUT LIMITING THE FOREGOING CATERPILLAR RESPONSIBILITIES AND USER RESPONSIBILITIES.
PROVISIONS OF THIS PARAGRAPH, WHERE A PRODUCT IS SUPPLIED FOR BUSINESS PURPOSES, THE
CONSUMER GUARANTEES UNDER THE CONSUMER GUARANTEES ACT 1993 (NZ) WILL NOT APPLY. TO THE EXTENT PERMISSIBLE BY LAW, THE TERMS SET OUT IN THE REMAINDER OF THIS WARRANTY
DOCUMENT (INCLUDING SECTION B) CONTINUE TO APPLY TO PRODUCTS TO WHICH THIS SECTION C
NEITHER THIS WARRANTY NOR ANY OTHER CONDITION OR WARRANTY BY CATERPILLAR, EXPRESS APPLIES.
OR IMPLIED (SUBJECT ONLY TO THE MANDATORY RIGHTS), IS APPLICABLE TO ANY ITEM CATERPILLAR
SELLS THAT IS WARRANTED DIRECTLY TO THE USER BY ITS MANUFACTURER. ©2016 Caterpillar All Rights Reserved.
CAT, CATERPILLAR, their respective logos, "Caterpillar Yellow" the "Power Edge" trade dress as well as corporate and
IF THE MANDATORY RIGHTS MAKE CATERPILLAR LIABLE IN CONNECTION WITH SERVICES OR GOODS, product identity used herein, are trademarks of Caterpillar and may not be used without permission.
THEN TO THE EXTENT PERMITTED UNDER THE MANDATORY RIGHTS, THAT LIABILITY SHALL BE LIMITED
AT CATERPILLAR’S OPTION TO (a) IN THE CASE OF SERVICES, THE SUPPLY OF THE SERVICES AGAIN OR
THE PAYMENT OF THE COST OF HAVING THE SERVICES SUPPLIED AGAIN AND (b) IN THE CASE OF GOODS,
THE REPAIR OR REPLACEMENT OF THE GOODS, THE SUPPLY OF EQUIVALENT GOODS, THE PAYMENT OF
THE COST OF SUCH REPAIR OR REPLACEMENT OR THE ACQUISITION OF EQUIVALENT GOODS.
SELF5709