Professional Documents
Culture Documents
PRODUCT DESCRIPTION
Series DMB is a direct acting (self-actuated spring loaded) pressure
regulators for general purpose pressure regulating applications. These
regulators are best suited for delivering constant reduced pressure of pre-
filtered, non-corrosive gases & liquids used in industrial, commercial & process
plant applications.
Figure 1 : Series DMB
DMB
Direct Acting Pressure Regulator The balanced trim design with internal sensing as well as with external sensing exhibits
excellent control of downstream pressure even with very high variations in inlet pressure.
KEY FEATURES
l Balanced Trim Design : Accurately balanced trim provides lesser droop over conventional direct acting regulators resulting in high
flow capacity. This regulators can handle very high inlet pressure without affecting the accuracy of outlet pressure control.
l Internal Sensing Through Pitot Tube : Internal pressure sensing provides faster response and easy to install in the pipeline with,
savings in cost of impulse tubes, fittings. The internal sensing through pitot tube further enhance the regulators accuracy.
l Interchangeable Springs : Springs are specially designed so that those can be interchanged in the same spring casing for achieving
wider set pressure range without any modifications. Additional springs can be supplied to cover wide spring range thus giving
freedom to opt for spring range according to process requirement at site.
l Tamper Resistant : An adjusting set screw with lock nut and protective cap is standard arrangement to discourage tampering with
pressure setting.
l Easy Maintenance : Regulator internals can be inspected & maintenance work can be carried out without removing body from the
pipeline.
l Tight Shut-Off Capability : Provides excellent tight shut-off capability over long working life.
TECHNICAL SPECIFICATION
l Valve Size* : l Flow Co-efficient :
½”, ¾”, 1", 1½”, 2", 3" & 4" Refer Table 2A for Series DMBL Series
l Body Rating : Refer Table 2B for Series DMB & Series DMBH
ANSI 150#, ANSI 300# & ANSI 600#.
l End Connection* :
MATERIAL OF CONSTRUCTION
Screwed & Flanged Type (acc. to Std. ASME B16.5). l Body* : A216 Gr. WCB (Standard), A351 Gr. CF8, A351 Gr.
l Model Variant : CF8M, A351 Gr. CF3, A351 Gr. CF3M.
Series DMBL (Low Pressure Application) l Diaphragm Casing & Spring Housing* : Carbon Steel /
Series DMB Series (Medium Pressure Application) A216 Gr. WCB (Standard), Stainless Steel / A351 Gr. CF8,
Stainless Steel / A351 Gr. CF8M.
Series DMBH (High Pressure Application)
l Diaphragm* : Nitrile (Standard), Neoprene, EPDM, Viton,
l Spring Casing & Diaphragm Casing Pressure Maximum :
Silicon, PTFE backed Polymers.
Series DMBL : 2.5 Kg/cm2g.
l Disc*: Nitrile (Standard), Neoprene, EPDM, Viton, Silicon.
Series DMB : 10.5 Kg/cm2g.
2
l Internal Trim Parts* : SS316, SS316L (Standard).
Series DMBL : 50.0 Kg/cm g. *Other special materials are available on request.
l Spring Ranges :
Refer Table 1A for Series DMBL NOTES 1:
Refer Table 1B for Series DMB l Series DMBL is available upto 4" valve size whereas,
Refer Table 1C for Series DMBH Series DMB & DMBH is available upto 2" valve size only .
l Temperature Capabilities : -450C to 2000C with different l Screwed end is applicable only to valve size upto 1".
elastomeric parts. l PTFE Backed Polymers is available only for Series DMB.
l Pressure Setting Adjustment : Adjustable throughout the l If Cv calculated > 70% of Cv-o, sensing should be external
spring range by turning the adjusting set screw. sensing type.
l Pressure Registration : l Pressure rating ANSI 150# & ANSI 300# is applicable only
Internal (Standard); for Series DMBL with minimum inlet pressure upto 7.0
External (Optional). Barg.
DMB/19/08/R7 PAGE 2 OF 6
SERIES DMB
DIRECT ACTING PRESSURE REGULATOR
OPERATING PRINCIPLE
TABLE 1A : SPRING RANGE DETAILS (SERIES DMBL) TABLE 1B : SPRING RANGE DETAILS (SERIES DMB)
Outlet Set Pressure Spring Colour Max. Inlet Outlet Set Pressure Spring Colour Max. Inlet
Range Code Pressure Range Code Pressure
0.15 to 0.35 Barg. Red 7.0 Barg. 0.5 to 0.8 Barg. Yellow 19.0 Barg.
0.30 to 0.55 Barg. Orange 7.0 Barg. 0.7 to 1.6 Barg. Orange 19.0 Barg.
1.5 to 2.1 Barg. Red 19.0 Barg.
TABLE 1C : SPRING RANGE DETAILS (SERIES DMBH) 2.0 to 3.0 Barg. Green 19.0 Barg.
Outlet Set Pressure Spring Colour Max. Inlet 2.75 to 4.0 Barg. Blue 30.0 Barg.
Range Code Pressure
3.75 to 5.4 Barg. Black 30.0 Barg.
8.0 to 22.0 Barg. Black 48.0 Barg.
4.5 to 6.5 Barg. Blue 48.0 Barg.
18.0 to 30.0 Barg. Black 48.0 Barg.
6.0 to 10.5 Barg. Black 48.0 Barg.
DMB/19/08/R7 PAGE 3 OF 6
SERIES DMB
DIRECT ACTING PRESSURE REGULATOR
MATERIAL OF CONSTRUCTION
BODY TRIM
DIAPHRAGM
A216 GR. WCB q A479 GR. SS316 q
Material Model
A351 GR. CF8 q A479 GR. SS316L q
A351 GR. CF8M q Nitrile q OTHERS* q
A351 GR. CF3 q Neoprene DMBL / DMB / q
‘O’ RING
A351 GR. CF3M q EPDM DMBH Series q Nitrile q
OTHERS* q Viton q Neoprene q
DISC PTFE + Nitrile q EPDM q
Nitrile PTFE + Neoprene q Viton q
q
DMB Series OTHERS* q
Neoprene q PTFE + Viton q
EPDM q PTFE + EPDM q NOTE:
Viton q
OTHERS* q 'OTHERS' Option to be specified by
OTHERS* q the Customer /Client.
DMB/19/08/R7 PAGE 4 OF 6
SERIES DMB
DIRECT ACTING PRESSURE REGULATOR
15NB 60.0 16.0 4.0 89.0 184.0 66.0 16.0 4.0 95.0 190.0 66.0 16.0 4.0 95.0 203.0
20NB 69.8 16.0 4.0 98.3 184.0 82.5 19.0 4.0 117.0 194.0 82.6 19.0 4.0 117.0 206.0
25NB 79.4 16.0 4.0 108.0 184.0 89.0 19.0 4.0 123.6 197.0 88.9 19.0 4.0 124.0 210.0
40NB 98.4 16.0 4.0 127.0 222.0 114.3 22.2 4.0 155.4 235.0 114.3 22.0 4.0 155.0 251.0
50NB 120.6 19.0 4.0 152.2 254.0 127.0 19.0 8.0 165.0 267.0 127.0 19.0 8.0 165.0 286.0
80NB 152.4 19.0 4.0 190.4 298.0 168.15 22.0 8.0 209.55 318.0 168.1 22.0 8.0 209.5 337.0
100NB 130.5 19.0 8.0 228.6 352.0 200.0 22.0 8.0 254.0 368.0 215.9 25.0 8.0 273.0 394.0
All Dimensions are in ‘mm’ FLANGE DIMENSIONS : p = Pitch Circle Diameter ; d = Bolt Hole Dia.; n = Nos. of Bolt Holes
DMB/19/08/R7 PAGE 5 OF 6
TABLE 5E : SCREWED END DIMENSIONS
VALVE S H
SIZE F L WEIGHT
(DN) D06 D08 D06 D08
Figure 4.
EXTERNAL DIMENSION
(Screwed End Regulator)
ENQUIRY SPECIFICATIONS
1st Floor, Samriddhi, L.B.S. Marg, Mulund (W), Mumbai - 400080, INDIA
Phone: +91-22-25608668 ; +91-9167780105 Fax: +91-25682771
Email: info@nirmalindustries.com ; Website: www.nirmal.co.in
The contents of this publication are presented for informational purposes only. While efforts have been made to ensure their accuracy, they are not to be construed as
warranties or guarantees, expressed or implied, regarding the products or services described herein or their use or applicability. Individuals using this data must exercise
their independent judgement in evaluating product selection and determining product appropriateness for their particular purpose and system requirements. Nirmal
reserves the right to modify or improve product designs and specification without any notice. Please get in touch with Nirmal for details related to previous versions of the
product which may have been supplied or offered to you in past.
DMB/19/08/R7 PAGE 6 OF 6