This document provides adjustment specifications for press fits and clearances between coupled machine parts. It lists 13 adjustment types from S6 to D9, describing when each would be used based on factors like how tightly parts need to be joined and how often they need to be coupled/uncoupled. For each adjustment type, examples of relevant applications are given, such as bearings, gears, pulleys, and other rotating or moving machine components. Tables provide nominal diameter differences and passage/non-passage values for holes corresponding to the adjustment types.
This document provides adjustment specifications for press fits and clearances between coupled machine parts. It lists 13 adjustment types from S6 to D9, describing when each would be used based on factors like how tightly parts need to be joined and how often they need to be coupled/uncoupled. For each adjustment type, examples of relevant applications are given, such as bearings, gears, pulleys, and other rotating or moving machine components. Tables provide nominal diameter differences and passage/non-passage values for holes corresponding to the adjustment types.
This document provides adjustment specifications for press fits and clearances between coupled machine parts. It lists 13 adjustment types from S6 to D9, describing when each would be used based on factors like how tightly parts need to be joined and how often they need to be coupled/uncoupled. For each adjustment type, examples of relevant applications are given, such as bearings, gears, pulleys, and other rotating or moving machine components. Tables provide nominal diameter differences and passage/non-passage values for holes corresponding to the adjustment types.
that have a xed coupling, and their disassembly INTERNATIONAL SETTINGS I.S.A AXIS h 6 FINE ADJUSTMENT SINGLE AXIS is infrequent, being able to couple and uncouple Press t S 6 and y R 6 NOMINAL DIFFERENCES with a regular hand hammer in small pieces, and > Forced N 7 fountain hammer in large ones; It is necessary to > Trailed M 7 FIGURES MARKED WITH ASTERISK DOES NOT PASS ensure the movement, of rotation by means of a For the holes corre- > Adhesion K 7 key or another, as well as the longitudinal move- Shaft h6 spond this series of > Soft input J 7 ment. DIAMETERS PASS HOLES CAN’T PASS adjustments > Sliding H 7 NOMINAL > Free play fair G 7 Some applications: Wheel bushings, pulleys and mm. Can’t Pass > Free play F 7 connecting rods, plates for shaft feeders, distri- - Pass H7 G7 > Light game E 8 bution eccentrics, on shafts, ball bearings on sha- More than 1 to 3 +0.009* +0.012* > strong game D 9 fts for medium loads, ywheels, turbine runners 0.000 0.003 and centrifugal pumps, bolts on connecting rods, More than 3 to 6 +0.012* +0.016* APPLICATION OF I.S.A. SETTINGS induced on their shafts , brake discs gland slee- 0.000 0.004 PRESS FIT S7 AND R7-used for precision-joined, ves; Rudder crossheads and horn caps, ying More than 6 to 10 +0.015* +0.020* permanent-t parts; These adjustments depend buttresses and winch drums in shipbuilding 0.000 0.005 on the shape of the pieces (see shrinkage adjust- More than 10 to 18 +0.018* +0.024* ments), since in some couplings, when dealing 0.000 0.006 SOFT ENTRY ADJUSTMENT J7- It is used in +0.028* More than 18 to 30 +0.021* with large machines, greater interferences are pieces that must be coupled and uncoupled by 0.000 0.007 required. hand or with a soft blow to the wooden mallet. More than 30 to 40 +0.025* +0.034* More than 40 to 50 0.000 0.009 Some applications: Bearing bushings in their supp- Some applications: Inner rings of ball bearings More than 50 to 65 +0.030* +0.040* orts, in Wheels, in motor connecting rods,etc. for small loaders and outer rings of ball bearings in their boxes, gearbox wheels, xing rings, pins More than 65 to 80 0.000 0.010 FORCED ADJUSTMENT N7- Used for parts that and bolts of joints of connecting rods and timing must be solidly coupled in any case, being able to forks, bushings in supports that are frequently More than 80 to 100 +0.035* +0.047* couple and uncouple only by means of pressure, the disassembled, Caps on bearing brackets More than 100 to 120 0.000 0.012 turning movement must be ensured by means of a key or another. SLIDING ADJUSTMENT H7- It is used for parts More than 120 to 140 that, when well greased, can be coupled and un- +0.040* +0.054* Some applications: Mounted axles for wagons, Els coupled by hand. More than 140 to 160
of dynamos and electric motors, split wheels and 0.000 0.014
More than 160 to 180 pulleys on motor axles, bronze crowns on cast iron some applications: locating rings, pistons in oil cores to tooth after assembled, handlebars or brakes, sliding coupling plates, truck wheels on More than 180 to 200 cranks on axles, oscillating levers, trunnions or axles, one-piece pulleys with key, Columns and +0.046* +0.061* buttons crank on chain rings drill chuck bars, Friction couplings mounted on More than 200 to 225
their axles, turning journals in crankshafts and 0.000 0.015
More than 225 to 250 handlebars or cranks. DRAG ADJUSTMENT H7. Used in pieces with xed More than 250 to 280 +0.052* +0.069* VERY FAIR FREE PLAY ADJUSTMENT G7- It is coupling that can only be coupled and uncoupled used in parts that must have a very perceptible More than 280 to 315 0.000 0.017 with a heavy hammer blow; the turning movement clearance. must be ensured by means of a key or another. Some applications: Sliding gear wheels in gear Some applications: Toothed wheels and pulleys, ball boxes, sliding couplings, governor mechanisms, bearing rings mounted on shafts for normal loads, grinding machine bearings, crankshaft bearings levers, bushings