Professional Documents
Culture Documents
2012−01
Processes
Multiprocess Welding
Description
UWI 400
(380/440 Volt Model) CE
TABLE OF CONTENTS
MILLER Electric Mfg. Co., 1635 Spencer Street, Appleton, WI 54914 U.S.A. declares that the
product(s) identified in this declaration conform to the essential requirements and provisions of
the stated Council Directive(s) and Standard(s).
Product/Apparatus Identification:
Product Stock Number
UWI 400 670398
Council Directives:
• 2006/95/EC Low Voltage
• 2004/108/EC Electromagnetic Compatibility
Standards:
• IEC 609741: 2005 Arc Welding Equipment – Welding Power Sources
• IEC 6097410: 2007 Arc Welding Equipment Electromagnetic Compatibility Requirements
• EN 50445 Product family standard to demonstrate compliance of equipment for resistance welding, arc
welding and allied processes with the basic restrictions related to human exposure to electromagnetic fields
(0 Hz – 300Hz) BS EN 50445:2008.
US Signatory:
_____________________________________ ________________________________________
David A. Werba Date of Declaration
241526C
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING
som 2011−10
7
Protect yourself and others from injury — read, follow, and save these important safety precautions and operating instructions.
D Always verify the supply ground − check and be sure that input
The symbols shown below are used throughout this manual power cord ground wire is properly connected to ground terminal in
to call attention to and identify possible hazards. When you
disconnect box or that cord plug is connected to a properly
see the symbol, watch out, and follow the related instructions
grounded receptacle outlet.
to avoid the hazard. The safety information given below is
only a summary of the more complete safety information D When making input connections, attach proper grounding conduc-
found in the Safety Standards listed in Section 1-5. Read and tor first − double-check connections.
follow all Safety Standards. D Keep cords dry, free of oil and grease, and protected from hot metal
and sparks.
Only qualified persons should install, operate, maintain, and
repair this unit. D Frequently inspect input power cord for damage or bare wiring −
replace cord immediately if damaged − bare wiring can kill.
During operation, keep everybody, especially children, away. D Turn off all equipment when not in use.
D Do not use worn, damaged, undersized, or poorly spliced cables.
D Do not drape cables over your body.
ELECTRIC SHOCK can kill.
D If earth grounding of the workpiece is required, ground it directly
Touching live electrical parts can cause fatal shocks with a separate cable.
or severe burns. The electrode and work circuit is D Do not touch electrode if you are in contact with the work, ground,
electrically live whenever the output is on. The input or another electrode from a different machine.
power circuit and machine internal circuits are also
live when power is on. In semiautomatic or automatic D Do not touch electrode holders connected to two welding ma-
wire welding, the wire, wire reel, drive roll housing, chines at the same time since double open-circuit voltage will be
and all metal parts touching the welding wire are present.
electrically live. Incorrectly installed or improperly
grounded equipment is a hazard. D Use only well-maintained equipment. Repair or replace damaged
parts at once. Maintain unit according to manual.
D Do not touch live electrical parts.
D Wear a safety harness if working above floor level.
D Wear dry, hole-free insulating gloves and body protection. D Keep all panels and covers securely in place.
D Insulate yourself from work and ground using dry insulating mats
D Clamp work cable with good metal-to-metal contact to workpiece
or covers big enough to prevent any physical contact with the work
or worktable as near the weld as practical.
or ground.
D Do not use AC output in damp areas, if movement is confined, or if D Insulate work clamp when not connected to workpiece to prevent
there is a danger of falling. contact with any metal object.
D Use AC output ONLY if required for the welding process. D Do not connect more than one electrode or work cable to any
D If AC output is required, use remote output control if present on single weld output terminal. Disconnect cable for process not in
unit. use.
D Additional safety precautions are required when any of the follow-
ing electrically hazardous conditions are present: in damp
SIGNIFICANT DC VOLTAGE exists in inverter weld-
locations or while wearing wet clothing; on metal structures such ing power sources AFTER removal of input power.
as floors, gratings, or scaffolds; when in cramped positions such D Turn Off inverter, disconnect input power, and discharge input
as sitting, kneeling, or lying; or when there is a high risk of unavoid- capacitors according to instructions in Maintenance Section
able or accidental contact with the workpiece or ground. For these before touching any parts.
conditions, use the following equipment in order presented: 1) a
semiautomatic DC constant voltage (wire) welder, 2) a DC manual
(stick) welder, or 3) an AC welder with reduced open-circuit volt- HOT PARTS can burn.
age. In most situations, use of a DC, constant voltage wire welder
is recommended. And, do not work alone! D Do not touch hot parts bare handed.
D Disconnect input power or stop engine before installing or D Allow cooling period before working on equip-
servicing this equipment. Lockout/tagout input power according to ment.
OSHA 29 CFR 1910.147 (see Safety Standards). D To handle hot parts, use proper tools and/or
wear heavy, insulated welding gloves and
D Properly install, ground, and operate this equipment according to
clothing to prevent burns.
its Owner’s Manual and national, state, and local codes.
OM-202 137 Page 1
D Remove stick electrode from holder or cut off welding wire at
FUMES AND GASES can be hazardous. contact tip when not in use.
D Wear oil-free protective garments such as leather gloves, heavy
Welding produces fumes and gases. Breathing shirt, cuffless trousers, high shoes, and a cap.
these fumes and gases can be hazardous to your
health. D Remove any combustibles, such as a butane lighter or matches,
from your person before doing any welding.
D Keep your head out of the fumes. Do not breathe the fumes.
D After completion of work, inspect area to ensure it is free of sparks,
D If inside, ventilate the area and/or use local forced ventilation at the glowing embers, and flames.
arc to remove welding fumes and gases.
D Use only correct fuses or circuit breakers. Do not oversize or by-
D If ventilation is poor, wear an approved air-supplied respirator. pass them.
D Read and understand the Material Safety Data Sheets (MSDSs) D Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B
and the manufacturer’s instructions for metals, consumables, for hot work and have a fire watcher and extinguisher nearby.
coatings, cleaners, and degreasers.
D Work in a confined space only if it is well ventilated, or while
FLYING METAL or DIRT can injure eyes.
wearing an air-supplied respirator. Always have a trained watch-
person nearby. Welding fumes and gases can displace air and
D Welding, chipping, wire brushing, and grinding
lower the oxygen level causing injury or death. Be sure the breath-
cause sparks and flying metal. As welds cool,
ing air is safe.
they can throw off slag.
D Do not weld in locations near degreasing, cleaning, or spraying op- D Wear approved safety glasses with side
erations. The heat and rays of the arc can react with vapors to form shields even under your welding helmet.
highly toxic and irritating gases.
D Do not weld on coated metals, such as galvanized, lead, or
cadmium plated steel, unless the coating is removed from the weld BUILDUP OF GAS can injure or kill.
area, the area is well ventilated, and while wearing an air-supplied
respirator. The coatings and any metals containing these elements D Shut off compressed gas supply when not in use.
can give off toxic fumes if welded. D Always ventilate confined spaces or use
approved air-supplied respirator.
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense ELECTRIC AND MAGNETIC FIELDS (EMF)
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Sparks fly off from the can affect Implanted Medical Devices.
weld.
D Wearers of Pacemakers and other Implanted
D Wear an approved welding helmet fitted with a proper shade of Medical Devices should keep away.
filter lenses to protect your face and eyes from arc rays and
sparks when welding or watching (see ANSI Z49.1 and Z87.1 D Implanted Medical Device wearers should consult their doctor
listed in Safety Standards). and the device manufacturer before going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating
D Wear approved safety glasses with side shields under your
operations.
helmet.
D Use protective screens or barriers to protect others from flash,
glare and sparks; warn others not to watch the arc. NOISE can damage hearing.
D Wear protective clothing made from durable, flame-resistant
material (leather, heavy cotton, or wool) and foot protection. Noise from some processes or equipment can
damage hearing.
WELDING can cause fire or explosion. D Wear approved ear protection if noise level is
high.
Welding on closed containers, such as tanks,
drums, or pipes, can cause them to blow up. Sparks
can fly off from the welding arc. The flying sparks, hot CYLINDERS can explode if damaged.
workpiece, and hot equipment can cause fires and
burns. Accidental contact of electrode to metal objects can cause
sparks, explosion, overheating, or fire. Check and be sure the area is Compressed gas cylinders contain gas under high
safe before doing any welding. pressure. If damaged, a cylinder can explode. Since
D Remove all flammables within 35 ft (10.7 m) of the welding arc. If gas cylinders are normally part of the welding
process, be sure to treat them carefully.
this is not possible, tightly cover them with approved covers.
D Protect compressed gas cylinders from excessive heat, mechani-
D Do not weld where flying sparks can strike flammable material.
cal shocks, physical damage, slag, open flames, sparks, and arcs.
D Protect yourself and others from flying sparks and hot metal. D Install cylinders in an upright position by securing to a stationary
D Be alert that welding sparks and hot materials from welding can support or cylinder rack to prevent falling or tipping.
easily go through small cracks and openings to adjacent areas. D Keep cylinders away from any welding or other electrical circuits.
D Watch for fire, and keep a fire extinguisher nearby. D Never drape a welding torch over a gas cylinder.
D Be aware that welding on a ceiling, floor, bulkhead, or partition can D Never allow a welding electrode to touch any cylinder.
cause fire on the hidden side. D Never weld on a pressurized cylinder − explosion will result.
D Do not weld on containers that have held combustibles, or on D Use only correct compressed gas cylinders, regulators, hoses,
closed containers such as tanks, drums, or pipes unless they are and fittings designed for the specific application; maintain them
properly prepared according to AWS F4.1 and AWS A6.0 (see and associated parts in good condition.
Safety Standards). D Turn face away from valve outlet when opening cylinder valve.
D Do not weld where the atmosphere may contain flammable dust, D Keep protective cap in place over valve except when cylinder is in
gas, or liquid vapors (such as gasoline). use or connected for use.
D Connect work cable to the work as close to the welding area as D Use the right equipment, correct procedures, and sufficient num-
practical to prevent welding current from traveling long, possibly ber of persons to lift and move cylinders.
unknown paths and causing electric shock, sparks, and fire D Read and follow instructions on compressed gas cylinders,
hazards. associated equipment, and Compressed Gas Association (CGA)
D Do not use welder to thaw frozen pipes. publication P-1 listed in Safety Standards.
OM-202 137 Page 2
1-3. Additional Symbols For Installation, Operation, And Maintenance
Welding or cutting equipment produces fumes or gases This product contains chemicals, including lead, known to
which contain chemicals known to the State of California to the state of California to cause cancer, birth defects, or other
cause birth defects and, in some cases, cancer. (California reproductive harm. Wash hands after use.
Health & Safety Code Section 25249.5 et seq.)
Pour écarter les risques de blessure pour vous−même et pour autrui — lire, appliquer et ranger en lieu sûr ces consignes relatives
aux précautions de sécurité et au mode opératoire.
LES RAYONS DE L’ARC peuvent D Utiliser exclusivement des fusibles ou coupe−circuits appropriés.
Ne pas augmenter leur puissance; ne pas les ponter.
provoquer des brûlures dans les
yeux et sur la peau. D Une fois le travail achevé, assurez−vous qu’il ne reste aucune
trace d’étincelles incandescentes ni de flammes.
Le rayonnement de l’arc du procédé de soudage
génère des rayons visibles et invisibles intenses D Utiliser exclusivement des fusibles ou coupe−circuits appropriés.
Ne pas augmenter leur puissance; ne pas les ponter.
(ultraviolets et infrarouges) susceptibles de provoquer des brûlures
dans les yeux et sur la peau. Des étincelles sont projetées pendant le D Suivre les recommandations dans OSHA 1910.252(a)(2)(iv) et
soudage. NFPA 51B pour les travaux à chaud et avoir de la surveillance et un
extincteur à proximité.
D Porter un casque de soudage approuvé muni de verres filtrants
approprié pour protéger visage et yeux pour protéger votre visage
et vos yeux pendant le soudage ou pour regarder (voir ANSI Z49.1
et Z87.1 énuméré dans les normes de sécurité). DES PIECES DE METAL ou DES
D Porter des lunettes de sécurité avec écrans latéraux même sous SALETES peuvent provoquer des
votre casque. blessures dans les yeux.
D Avoir recours à des écrans protecteurs ou à des rideaux pour
D Le soudage, l’écaillement, le passage de la pièce à la brosse en
protéger les autres contre les rayonnements les éblouissements
fil de fer, et le meulage génèrent des étincelles et des particules
et les étincelles ; prévenir toute personne sur les lieux de ne pas
métalliques volantes. Pendant la période de refroidissement des
regarder l’arc.
soudures, elles risquent de projeter du laitier.
D Porter des vêtements confectionnés avec des matières résistan- D Porter des lunettes de sécurité avec écrans latéraux ou un écran
tes et ignifuges (cuir, coton lourd ou laine) et des bottes de facial.
protection.
OM-202 137 Page 6
LES ACCUMULATIONS DE GAZ LES BOUTEILLES peuvent exploser
risquent de provoquer des blessures si elles sont endommagées.
ou même la mort.
Les bouteilles de gaz comprimé contiennent du gaz
D Fermer l’alimentation du gaz comprimé en cas sous haute pression. Si une bouteille est
de non utilisation. endommagée, elle peut exploser. Du fait que les
bouteilles de gaz font normalement partie du
D Veiller toujours à bien aérer les espaces confi- procédé de soudage, les manipuler avec
nés ou se servir d’un respirateur d’adduction précaution.
d’air homologué.
D Protéger les bouteilles de gaz comprimé d’une chaleur excessive,
des chocs mécaniques, des dommages physiques, du laitier, des
flammes ouvertes, des étincelles et des arcs.
D Placer les bouteilles debout en les fixant dans un support station-
Les CHAMPS ÉLECTROMAGNÉTIQUES (CEM) naire ou dans un porte-bouteilles pour les empêcher de tomber ou
peuvent affecter les implants médicaux. de se renverser.
D Tenir les bouteilles éloignées des circuits de soudage ou autres
D Les porteurs de stimulateurs cardiaques et circuits électriques.
autres implants médicaux doivent rester à D Ne jamais placer une torche de soudage sur une bouteille à gaz.
distance.
D Une électrode de soudage ne doit jamais entrer en contact avec
D Les porteurs d’implants médicaux doivent consulter leur une bouteille.
médecin et le fabricant du dispositif avant de s’approcher de la
zone où se déroule du soudage à l’arc, du soudage par points, du D Ne jamais souder une bouteille pressurisée − risque d’explosion.
gougeage, de la découpe plasma ou une opération de chauffage D Utiliser seulement des bouteilles de gaz comprimé, régulateurs,
par induction. tuyaux et raccords convenables pour cette application spécifique;
les maintenir ainsi que les éléments associés en bon état.
D Détourner votre visage du détendeur-régulateur lorsque vous
ouvrez la soupape de la bouteille.
D Le couvercle du détendeur doit toujours être en place, sauf lorsque
LE BRUIT peut endommager l’ouïe. la bouteille est utilisée ou qu’elle est reliée pour usage ultérieur.
D Utiliser les équipements corrects, les bonnes procédures et suffi-
Le bruit des processus et des équipements peut samment de personnes pour soulever et déplacer les bouteilles.
affecter l’ouïe.
D Lire et suivre les instructions sur les bouteilles de gaz comprimé,
D Porter des protections approuvées pour les l’équipement connexe et le dépliant P-1 de la CGA (Compressed
oreilles si le niveau sonore est trop élevé. Gas Association) mentionné dans les principales normes de sécu-
rité.
Les équipements de soudage et de coupage produisent des Ce produit contient des produits chimiques, notamment du
fumées et des gaz qui contiennent des produits chimiques plomb, dont l’État de Californie reconnaît qu’ils provoquent
dont l’État de Californie reconnaît qu’ils provoquent des mal- des cancers, des malformations congénitales ou d’autres
formations congénitales et, dans certains cas, des cancers. problèmes de procréation. Se laver les mains après
(Code de santé et de sécurité de Californie, chapitre 25249.5 utilisation.
et suivants)
Warning! Watch Out! There are possible 2 Breathing welding fumes can be 3.3 Do not weld on drums or any closed
hazards as shown by the symbols. hazardous to your health. containers.
2.1 Keep your head out of the fumes. 4 Arc rays can burn eyes and injure
1 Electric shock from welding electrode skin.
or wiring can kill. 2.2 Use forced ventilation or local exhaust
to remove the fumes. 4.1 Wear hat and safety glasses. Use ear
1.1 Wear dry insulating gloves. Do not 2.3 Use ventilating fan to remove fumes. protection and button shirt collar. Use
touch electrode with bare hand. Do welding helmet with correct shade of
not wear wet or damaged gloves. 3 Welding sparks can cause explosion
or fire. filter. Wear complete body protection.
1.2 Protect yourself from electric shock by 3.1 Keep flammables away from welding. 5 Become trained and read the
insulating yourself from work and Do not weld near flammables. instructions before working on the
ground. machine or welding.
3.2 Welding sparks can cause fires. Have
1.3 Disconnect input plug or power before a fire extinguisher nearby, and have a 6 Do not remove or paint over (cover)
working on machine. watchperson ready to use it. the label.
Kasjf;laksf;lkasdf'l;aksdf;lkasd;flksadflkasd;lk
179310-B
4/96
179309-C
2 3 4 5
202563-B
1/96
A Amperage Panel
Alternating
Current (AC) V Voltage
U0 Rated No Load
Voltage (Average) U1 Primary Voltage
U2 Conventional
Load Voltage X Duty Cycle
Hz Hertz IP Degree Of
Protection I2 Rated Welding
Current % Percent
Lift-Arc Trigger
Pulsed Hold Operation Single Phase Three Phase
(GTAW)
! This equipment shall not be used by the general public as the EMF limits for the general public might be exceeded during welding.
This equipment is built in accordance with EN 60974−1 and is intended to be used only in an occupational environment (where the general public
access is prohibited or regulated in such a way as to be similar to occupational use) by an expert or an instructed person.
Wire feeders and ancillary equipment (such as torches, liquid cooling systems and arc striking and stabilizing devices) as part of the welding
circuit may not be a major contributor to the EMF. See the Owner’s Manuals for all components of the welding circuit for additional EMF exposure
information.
S At a distance of 1 meter the EMF exposure values were less than 20% of the permissible values.
4-3. Specifications
*While idling
Notes
Overheating
0 A
15
OR
Minutes Reduce Duty Cycle
C. CC Mode
D. CV Mode
ARC CONTROL
12-1/2 in.
G 1/4-20 UNC -2B thread
(318 mm)
Weight
B
76 lb (34.6 kg)
804 801-A
Location
4
18 in.
(460 mm)
18 in.
(460 mm) Ref. ST-151 556 / 801 192
Weld Cable Size** and Total Cable (Copper) Length in Weld Circuit
Not Exceeding***
Weld Output
Terminals
Notes
NOTICE − INCORRECT INPUT POWER can damage this welding power source. This welding power source requires a CONTINUOUS supply of
input power at rated frequency(+10%) and voltage (+10%). Phase to ground voltage shall not exceed +10% of rated input voltage. Do not use a genera-
tor with automatic idle device (that idles engine when no load is sensed) to supply input power to this welding power source.
NOTICE − Actual input voltage should not be 10% less than minimum and/or 10% more than maximum input voltages listed in table. If actual input
voltage is outside this range, output may not be be available.
Failure to follow these electrical service guide recommendations could create an electric shock or fire hazard. These recommenda-
tions are for a dedicated circuit sized for the rated output and duty cycle of the welding power source.
In dedicated circuit installations, the National Electrical Code (NEC) allows the receptacle or conductor rating to be less than the rating
of the circuit protection device. All components of the circuit must be physically compatible. See NEC articles 210.21, 630.11, and
630.12.
Time-Delay Fuses 2 20 20
Normal Operating Fuses 3 30 25
Min Input Conductor Size In AWG 4 14 14
Max Recommended Input Conductor Length In Feet (Meters) 120 (37) 161 (49)
Min Grounding Conductor Size In AWG 4 14 14
Notes
Tools Needed:
1 2 3 4
7 5 6
202 133
1 Power On/Off Switch best results, place Inductance/Dig control in When set lower, short-circuit amperage at
the maximum position. low arc voltage is the same as normal welding
. The fan motor is thermostatically 6 Voltage/Amperage Control Switch amperage.
controlled and only runs when cooling is For front panel control, place switch in Panel
needed. When set higher, short-circuit amperage is in-
position. creased at low arc voltage to assist with arc
2 Voltmeter (see Section 5-2) For remote control, make connections to Re- starts as well as reduce sticking while weld-
3 Ammeter (see Section 5-2) mote 14 receptacle, and place switch in ing (see volt-ampere curves in Section 4-5).
Remote position. In most modes, remote
4 Voltage/Amperage Adjustment Control control is a percent of the Voltage/Amperage Select setting best suited for application.
5 Mode Switch Adjustment control setting (the value se-
lected on Voltage/Amperage Adjustment Control adjusts inductance when a MIG
The Mode switch setting determines both the control is maximum available on remote). In (GMAW) position is selected on the mode
process and output On/Off control (see Sec- the MIG mode, remote control provides full switch. Inductance determines the “wetness”
tion 5-3. Source of control (panel or remote) range of unit output regardless of V/A Adjust of the weld puddle. When set higher, “wet-
for the amount of output is selected on the control setting. ness” (puddle fluidity) increases.
Voltage/Amperage Control switch.
7 Inductance/Dig Control When pulsed MIG, or one of the TIG (GTAW)
For Air Carbon Arc (CAC-A) cutting and Control adjusts Dig when a Stick (SMAW) processes is selected, this control is not func-
gouging, place switch in Stick position. For welding position is selected on mode switch. tional.
. The meters display the actual weld output values for approximately three seconds after the arc is broken.
V A
Lift-Arc Trigger
Hold TIG (GTAW) 85
Blank Preset Amps
V A
TIG (GTAW) 85
Blank Preset Amps
V A
V A
Pulsed MIG
(GMAW-P)
PPP PPP
Pulse Display Pulse Display
V A
Remote
Control SMAW 85
Blank Preset Amps
V A
Panel Control
SMAW 80.0 85
Actual Volts (OCV) Preset Amps
. The SMAW modes provide the Adaptive Hot Start™ feature, which automatically increases the output amperage at the start of a weld should the
start require it. This eliminates electrode sticking at arc start.
Select: or Amp
Lift-Arc Trigger
Hold TIG (GTAW)
Requires: Control
Select: or Volt
MIG (GMAW)
Requires: Feeder
Pulsed MIG
(GMAW-P) Select: Volt
(Requires an
external
pulsing device.) Requires: Feeder or Control
Select: or Amp
Remote
Control SMAW
Requires: Control
Select: or Amp
Panel Control
SMAW
Weld
. Procedure requires:
control
Start sequence:
• Touch tungsten electrode to
workpiece at weld start point.
1 2 • Momentarily depress output
switch.
• Slowly lift electrode. An arc will
form when electrode is lifted.
• To stop welding, momentarily
1−2 depress output switch and out-
“Touch” Seconds put will shut off.
Note: If output switch is momen-
tarily depressed and tungsten is
not touching workpiece:
Do not touch tungsten to work.
Output will shut off in 3 seconds.
Start sequence over.
3 Months
Replace Repair Or
Damaged Or Replace Replace Cracked
Unreadable Cracked Torch Body
Labels Cables
Repair Or Replace
Cracked Cables
And Cords
Clean
And
Tighten Weld
Connections
6 Months
ST-801 192
V A
Help 0 Display
V A
Help 1 Display
V A
Help 2 Display
V A
Help 3 Display
V A
Help 4 Display
V A
Help 5 Display
V A
Help 6 Display
V A
Help 7 Display
V A
Help 8 Display
V A
Help 9 Display
1 2
6-6. Troubleshooting
Trouble Remedy
No weld output; unit completely inop- Place line disconnect switch in On position (see Section 4-11).
erative.
Check and replace line fuse(s), if necessary, or reset circuit breaker (see Section 4-11).
No weld output; meter display On. If using remote control, be sure Mode Selector switch is in a position that provides output control at
Remote 14 receptacle.
Unit overheated. Allow unit to cool with fan On (see Section 4-4).
Erratic or improper weld output. Use proper size and type of weld cable (see Section 4-8).
No 110 volts AC output at Remote 14 Reset supplementary protector CB1 (see Section 6-5).
receptacle.
No 24 volts AC output at Remote 14 Reset supplementary protector CB2 (see Section 6-5).
receptacle.
239 530-B
16
9
8
10
23
15
64
14
11
65 7 12 13
63
6
5
4
62
61
26
46 27
45 28
40
53 47 39 33
56 55 48
22 58
49 11 14
57 38 37 36
59
34
35
802 801-D
Item Dia. Part
No. Mkgs. No. Description Quantity
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT PARTS.
Unitor ASA
Drammensveien 211
P.O. Box 300 Skoyen
N−0212 Oslo
Norway
Tel: +47 22 13 14 15