Professional Documents
Culture Documents
NITSurat GeocellFoundations
NITSurat GeocellFoundations
net/publication/320145545
CITATION READS
1 9,850
2 authors:
Some of the authors of this publication are also working on these related projects:
All content following this page was uploaded by Arghadeep Biswas on 01 October 2017.
Abstract
Geocell-reinforcement in ground improvement is being used very extensively in present days.
It is a three dimensional honeycombed confinement system, made of geosynthetics, which
significantly improves the bearing capacity of soft soils, specially, in foundations, and
pavements applications. Apart from improving the soil strength, it has also been extensively
used in various slope stabilization, embankment construction and railway track applications.
Various parameters are needed to be considered and designed for the application of geocell
systems, like: geometrical parameters of geocell, its location and infill soil characteristics
This paper briefly discussed about geocell reinforced foundation systems and various
parameters influencing the performance of the same. The developments and parametric
studies on geocell foundation performances are discussed giving the optimum values of
various parameters.
INTRODUCTION
The credit of introducing the systematic concept of reinforcing the soil has been with
Vidal (1969). Over the time, soil-reinforcement has been modified according to new
inventions and requirements. The metallic strip-reinforcements in the beginning (Binquet and
Lee, 1975) were replaced by polymeric sheet-type-reinforcement and afterwards, the versatile
geosynthetics in different forms such as geotextile, geogrid, and geocells have superseded all.
Geocell, the three-dimensional honeycombing confining system, was devised by Webster and
Watkins (1977). In last few decades, the benefits of geocell-reinforcements, considering
several aspects such as material-strength, geometry, placement depths etc., have been
demonstrated by several investigators. Several field applications (Johnson, 1982; Bush et al.,
1990; Cowland and Wong, 1993; Emersleben and Meyer, 2008) and laboratory studies
(Shimizu and Inui, 1990; Dash et al., 2001, 2003; Sitharam et al., 2005, 2007; Zhang et al.,
2010; Mehrjardi et al. 2013; Tafreshi et al., 2010; Biswas et al., 2013, 2015) have highlighted
the benefits of three dimensional geocell reinforcement. This paper briefly discusses about
geocell reinforced foundation systems and various parameters influencing the performance of
the same.
MECHANISM OF GEOCELL REINFORCEMENT
Geocells, made of geosynthetics such as geotextiles or geogrids, are thermally welded
or mechanically bonded interconnected pocket-structures, in the form of mattress, used with
in-filled soil. General reinforcing mechanisms of geocell is confining the in-fill soil from
shearing away and derive anchorage resistance through the surrounding soil against the
applied load. Geocell walls cut the potential failure planes (which would be the case in
unreinforced condition) and force it to go deeper in to the soil as shown in Fig. 1. The
1
Training Course on ‘Introduction to Geosynthetics and Their Applications’
December 14, 2015, NIT Surat
interconnected pockets provide all round confinement to the in-filled soil and resists from
squeezing out under shear. In addition, the geocell-walls derive interfacial resistances with
surrounding soil through its apertures and develop anchorage with the soil to improve the
load bearing capacity of the reinforced-system (Fig. 2). As a whole, the in-filled geocell-soil
mattress behave like a semi-rigid slab which redistribute the incoming load over wider area
onto the underlying soil leading to improved performance of the system with reduced stress
intensity and the associated settlements.
2
Training Course on ‘Introduction to Geosynthetics and Their Applications’
December 14, 2015, NIT Surat
different parameters shown in the Fig. 3. The ‘h’, ‘b’, and ‘d’ are representing the height,
width, and pocket size of the geocell mattress, respectively. The placement depth below the
footing or the thickness of soil-cushion provided in between the footing and geocell-mattress
is denoted by ‘u’.
Footing
u
d
Soil -1
H
Geocell-Mattress
h
Soil -2 b
3
Training Course on ‘Introduction to Geosynthetics and Their Applications’
December 14, 2015, NIT Surat
INFLUENCING PARAMPETRS
Performance of geocell-reinforced foundation system depends on various parameters.
Laboratory model studies revealed several influencing parameters having immense effect on
geocell-reinforced foundation system.
Formation Pattern
The chevron pattern (Fig. 4) of geocell formation was reported to be more beneficial over
diamond pattern as it have more joints per unit area so as the rigidity (Webster, 1979; Dash et
al., 2001; Krishnaswamy et al., 2000; Pokharel et al., 2010).
Pocket Size
The pocket size (d) of a geocell-mattress is generally expressed as the diameter of an
equivalent circular area of the geocell pocket opening (in plan). It has been recommended
that the pocket opening should be less than the loading diameter and found that the smaller
geocell-pockets give higher performance (Mandal and Gupta, 1994; Mhaiskar and Mandal,
1996; Dash et al. 2001, 2003). However, due to constructional difficulties it has been
recommended to make pocket opening of geocell mattress slightly smaller than the footing
area so that the footing can cover at least one full pocket opening. Optimum pocket size
recommended as 0.8D where ‘D’ is the footing diameter (Dash et al. 2003).
4
Training Course on ‘Introduction to Geosynthetics and Their Applications’
December 14, 2015, NIT Surat
as farthest rupture planes were observed well within 2B distance at each side of the footing
(Dash et al. 2001). Figure 5b shows the effect of geocell height on the performance model
foundations (Sireesh et al., 2009). The optimum height has been reported to be in the range 1-
1.5D.
(a) (b)
Fig. 5 (a)Effect of geocell width (Latha et al. 2009) (b) Effect of geocell height (Sireesh et al.,
2009)
Placement Depth
Placement depth of the geocell below the footing is the height of sand cushion (u) in between
footing and geocell mattress (Fig. 2). This soil cushion redistributes the incoming load with a
lesser intensity and uniformly to the underlying geocell-mattress and thus prevents the
geocell-wall from early local buckling (Dash et al., 2001; Yoon et al., 2008; Tafreshi and
Dawson, 2010). Placement depth of 0.1D has been recommended as the optimum value to
prevent geocell wall from direct loading as shown in Fig. 6 (Dash et al. 2001).
Geogrid Properties
Stiffness of geogrid, orientation of ribs and aperture opening size (da) also has great influence
in improving the reinforcing effect of geocell (Rajagopal et al., 1999; Krishnaswamy et al.,
2000; Dash et al., 2001, Dash, 2012). It is seen that having larger opening size, the geogrid
develops better interlocking and anchorage with the soil particles than the solid walled or
perforated walled geocells (geoweb) which gives rise in improving the performance. In other
side geogrids having smaller opening sizes has higher improvement capacity, as the
confinement of in filled soil is better in smaller openings and per unit surface area for
frictional resistance and anchorage effect increases. This produces a comparatively stiff
5
Training Course on ‘Introduction to Geosynthetics and Their Applications’
December 14, 2015, NIT Surat
geocell-sand mattress and redistributes the loads even better. The orientation of geogrid ribs
is also significant in improving load bearing capacity. Horizontal and vertical orientation of
ribs (square or rectangular openings) gives better resistance against loading than the inclined
orientation (diamond openings).
0
H = 0.63D cu = 7 kPa
Clay + Sand cu = 15 kPa
-10
-15
-20
-25
6
Training Course on ‘Introduction to Geosynthetics and Their Applications’
December 14, 2015, NIT Surat
geocell-mattress (Dash et al., 2001; Sitharam et al., 2007, Biswas et al., 2015). Table 1 is
summarizing the optimum values after normalized with footing diameter (D) or footing width
(B).
Table 1 Optimum value of the parameters
Parameters Values (Range)
Formation Pattern Chevron
Rib Orientation Horizontal & Vertical
Geogrid Opening (da/D50) 80
CONCLUSIONS
This paper briefly discussed about geocell reinforced foundation systems and various
parameters influencing the performance of the same. The developments and parametric
studies on geocell foundation performances are discussed giving the optimum values of
various parameters. To have a better performance of geocell-reinforced soil, one must
consider the different influencing parameters and their working mechanism. The behaviour
and design of geocell reinforced soil structures is yet to be fully explored for developing the
design guidelines.
References
Binquet, J. and Lee, K.L. (1975). Bearing capacity tests on reinforced earth slabs, Journal of the
Geotechnical Engineering Division, ASCE, Vol. 101, 1241-1276.
Biswas A., Krishna A.M., and Dash S.K. (2013). Influence of subgrade strength on the performance
of geocell-reinforced foundation systems. Geosyn. Int., 20(6): 376-388.
Biswas, A., Ansari, M.A., Dash, S.K., and Krishna, A.M. (2015). Behavior of geogrid reinforced
foundation system supported on clay subgrades of different strengths. Int. J. Geosynth. Ground
Engg. Spinger, DOI: 10.1007/s40891-015-0023-5.
Bush, D.I., Jenner, C.G. and Bassett, R.H. (1990). The Design and Construction of Geocell
Foundation Mattresses Supporting Embankments over Soft Ground, Geotextiles and
Geomembranes (9) 83-98.
Cowland, J.W. and Wong, S.C.K. (1993). Performance of a road embankment on soft clay supported
on a geocell mattress foundation, Geotextiles and Geomembranes (12) 687-705.
Dash S.K. (2012). Effect of Geocell Type on Load Carrying Mechanism of Geocell Reinforced Sand
Foundations. International Journal of Geomechanics. August. doi:10.1061/(ASCE)GM.1943-
5622.0000162
Dash, S.K. (2010). Influence of relative density of soil on performance of geocell reinforced sand
foundations, Journal of Materials in Civil Engineering, ASCE, May, 533-538.
7
Training Course on ‘Introduction to Geosynthetics and Their Applications’
December 14, 2015, NIT Surat
Dash, S.K., Krishnaswamy, N.R. and Rajagopal, K. (2001). Bearing capacity of strip footings
supported on geocell-reinforced sand, Geotextiles and Geomembranes (19) 235–256.
Dash, S.K., Sireesh, S. and Sitharam, T.G. (2003). Model studies on circular footing supported on
geocell reinforced sand underlain by soft clay, Geotextiles and Geomembranes (21) 197–219.
Emersleben, A. and Meyer, N. (2008). The use of geocells in road constructions over soft soil:
Vertical stress and falling weight deflectometer measurements, EuroGeo4 Paper number 132,
2008.
Johnson, J.E. (1982). Bridge and Tidal Waters, Municipal Engineer, 109, 104 - 107.
Krishnaswamy, N.R., Rajagopal, K. and Latha, G. M. (2000). Model studies on geocell supported
embankments constructed over a soft clay foundation, Geotech. Test. J., 23(2), 45–54.
Latha, G.M., Dash, S.K. and Rajagopal, K. (2009). Numerical Simulation of the Behavior of Geocell
Reinforced Sand in Foundations, International Journal of Geomechanics, ASCE (8) 143-152.
Mandal, J.N. and Gupta, P. (1994). Stability of geocell-reinforced soil, Construction and building
materials, 8, 55-62.
Mhaiskar, S.Y., and Mandal, J.N. (1996). Investigations on soft clay subgrade strengthening using
geocells, Construction and Building Materials, Vol. 10, No. 4, 281-286.
Pokharel, S. K., Han, J., Leshchinsky, D., Parsons, R. L., and Halahmi, I., (2010). “Investigation of
factors influencing behavior of single geocell-reinforced bases under static loading”. Geotextiles
and Geomembranes (28) 570-578.
Rajagopal, K., Krishnaswamy, N.R. and Latha, G.M. (1999). Behaviour of sand confined with single
and multiple geocells, Geotextiles and Geomembranes (17) 171-184.
Shimizu, M. and Inui, T. (1990). Increase in the bearing capacity of ground with geotextile wall
frame. Proc of the Fourth International Conference on Geotextiles Geomembranes and Related
Products, Hague, Netherlands, 1, 254.
Sireesh, S., Sitharam, S. and Dash, S.K. (2009). Bearing capacity of circular footing on geocell-sand
mattress overlying clay bed with void, Geotextiles and Geomembranes (27), 89-98
Sitharam, G.T., Sireesh, S. and Dash, S.K. (2007), Performance of surface footing on geocell-
reinforced soft clay beds, Geotech. Geol. Eng. (25) 509–524
Sitharam, T.G., Sireesh, S. and Dash, S.K. (2005). Model studies of a circular footing supported on
geocell-reinforced clay, Can. Geotech. J. (42) 693–703
Tafreshi, S.N.M. and Dawson, A.R. (2010). Comparison of bearing capacity of a strip footing on sand
with geocell and with planar forms of geotextile reinforcement, Geotextiles and Geomembranes
(28) 72-84.
Vidal, H. (1969). The principle of reinforced earth. Highway Research Record, 282, Washington,
D.C.
Webster, S.L. and Watkins, J.E. (1977). Investigation of Construction Techniques for Tactical Bridge
Approach Raods across Soft Ground, Technical Report S-77-1, United State Army Crops of
Engineers, Waterway Experiment Station, Mississippi, USA.
Yoon, Y.W., Heo, S.B. and Kim, K.S. (2008). Geotechnical performance of waste tires for soil
reinforcement from chamber tests, Geotextiles and Geomembranes (26) 100-107.
Zhang, L., Zhao, M., Shi, C. and Zhao, H. (2010). Bearing capacity of geocell reinforcement in
embankment engineering, Geotextiles and Geomembranes (28) 475-482.