Professional Documents
Culture Documents
92050/2023-06-15
Replaces: 10.2018
Features Contents
▶ Variable displacement pump with axial piston rotary Type code 2
group of swashplate design for hydrostatic drives in Hydraulic fluids 6
open circuit Working pressure range 8
▶ Flow is proportional to the drive speed and Technical data for sizes 40 to 1000 9
displacement. Technical data for sizes 71, 250, 355, 370 and 500 10
▶ The flow can be continuously changed by adjusting Characteristic curves 13
the swashplate. Overview of control devices 17
▶ Excellent suction characteristics Dimensions, size 40 to 1000 25
▶ Low noise level Dimensions, through drive 45
▶ With pre-compression volume for pressure pulsation Overview of mounting options 72
reduction Permissible mass moment of inertia 73
▶ Nominal pressure 380 bar / maximum pressure Combination pumps A4VSO + A4VSO 74
420 bar for selected control devices with port plate 36. Installation instructions 75
▶ Long service life Project planning notes 78
▶ Modular design Safety instructions 79
▶ Variable through drive options Related documentation 80
▶ Optical swivel angle indicator
▶ Any installation position possible
▶ Suitable for variable-speed drives
▶ HF operation with reduced data possible for HFC
operation, special version available
RE 92050/2023-06-15, Bosch Rexroth AG
2 A4VSO series 1x and 30 | Axial piston variable pump
Type code
Type code
01 02 03 04 05 06 07 08 09 10 11 12 13 14
A4VS O / –
Hydraulic fluid 40 71 125 180 250 355 370 500 750 1000
01 Mineral oil and HFD hydraulic fluids (no code) ● ● ● ● ● ● ● ● ● ●
HFA, HFB and HFC hydraulic fluids1)
Only with sealing material NBR nitrile rubber and shaft seal ● – – – – – – ● – – E
PTFE. Please order with code P in position 09.
High-speed version – ● – ○ ● ● ● ● – – H
Charge pump 40 71 125 180 250 355 370 500 750 1000
03 Without charge pump (without code) ● ● ● ● ● ● ● ● ● ●
With charge pump, can only be ordered with port plate 25
– – – – – – – – ● – L
(see item 12) and only in counter-clockwise rotation (see item 08).
Operating mode
04 Pump, open circuit O
Size (NG)
05 Geometric displacement,
40 71 125 180 250 355 370 500 750 1000
see "Technical data" on page 9
1) For the enhanced-power special version in HFC mode, 2) Observe the restrictions for operation with HF hydraulic fluids in
see data sheet 92053 and/or order position 09 For versions with the relevant data sheets for the controls and/or mounted valves.
HFA and HFB pressure media, see data sheet 90223 3) Nominal pressure 380 bar / maximum pressure 420 bar possible
when using port plate 36.
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 3
Type code
01 02 03 04 05 06 07 08 09 10 11 12 13 14
A4VS O / –
Directions of rotation 40 71 125 180 250 355 370 500 750 1000
08 Viewed on drive shaft Clockwise ● ● ● ● ● ● ● ● ● ● R
Counter-clockwise ● ● ● ● ● ● ○ ● ● ● L
Sealing material 40 71 125 180 250 355 370 500 750 1000
09 FKM (fluorocarbon rubber) / HFD operation ● ● ● ● ● ● ● ● ● ● V
Special version for HFC mode,
– ● ● ● ● ● – – – – F.
see data sheet 92053
Drive shaft 40 71 125 180 250 355 370 500 750 1000
10 Parallel keyed shaft DIN 6885 ● ● ● ● ● ● ● ● ● ● P
Splined shaft DIN 5480 ● ● ● ● ● ● ● ● ● ● Z
Mounting flange 40 71 125 180 250 355 370 500 750 1000
11 Based on ISO 3019-2 metric 4-hole ● ● ● ● ● ● ● – – – B
8-hole – – – – – – – ● ● ● H
Working port
12 Standard version 40 71 125 180 250 355 370 500 750 1000
Ports B and S: Lateral SAE flange, offset 90°,
metric fastening thread
● ● ● ● ● ● ● – – – 13
(can only be ordered without through drive (N00) or with K..
through drives)
Ports B and S: Lateral SAE flange, offset 90°,
metric fastening thread
● ● ● ● ● ● ● ● ● ● 25
2nd pressure port B1, opposite B plugged with flange plate
upon delivery
High-speed version 40 71 125 180 250 355 370 500 750 1000
Ports B and S: Lateral SAE flange, offset 90°,
metric fastening thread
– ● – – ● ● – – – – 13
(can only be ordered without through drive (N00) or with K..
through drives)
Ports B and S: Lateral SAE flange, offset 90°,
metric fastening thread
– ● – – ● ● ● ● – – 25
2nd pressure port B1, opposite B plugged with flange plate
upon delivery
Ports B and S: Lateral SAE flange, offset 90°,
metric fastening thread.
– – – – – – ● – – – 361)2)
2nd pressure port B1, opposite B plugged with flange plate
upon delivery; with pulsation damping
RE 92050/2023-06-15, Bosch Rexroth AG
4 A4VSO series 1x and 30 | Axial piston variable pump
Type code
01 02 03 04 05 06 07 08 09 10 11 12 13 14
A4VS O / –
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 5
Type code
01 02 03 04 05 06 07 08 09 10 11 12 13 14
A4VS O / –
Filtration (specification only with DS.. control) 40 71 125 180 250 355 370 500 750 1000
14 Without filter ● ● ● ● ● ● ● ● ● ● N
Intermediate plate filter (for DS.. control,
● ● ● ● ● ● – ● – – Z
see data sheet 92057)
Notice
▶ Note the project planning notes on page 78.
▶ In addition to the type code, please specify the
relevant technical data when placing your order.
▶ For information on combination pumps, see page 74
RE 92050/2023-06-15, Bosch Rexroth AG
6 A4VSO series 1x and 30 | Axial piston variable pump
Hydraulic fluids
Hydraulic fluids
The A4VSO, A4VSLO variable pump is designed for Selection of hydraulic fluid
operation with HLP mineral oil according to DIN 51524. Bosch Rexroth evaluates hydraulic fluids on the basis of
Application instructions and requirements for hydraulic fluid the Fluid Rating according to the technical
selection, behavior during operation as well as disposal and data sheet 90235.
environmental protection should be taken from the Hydraulic fluids with positive evaluation in the Fluid Rating
following data sheets before the start of project planning: are listed in the following data sheet:
▶ 90220: Hydraulic fluids based on mineral oils and ▶ 90245 Bosch Rexroth fluid rating list for Rexroth
related hydrocarbons hydraulic components (pumps and motors)
▶ 90221: Environmentally acceptable hydraulic fluids
▶ 90222: Fire-resistant, water-free hydraulic fluids The hydraulic fluid should be selected so that the
(HFDR/HFDU) operating viscosity in the operating temperature range is
▶ 90223: Fire-resistant, water-containing hydraulic fluids within the optimum range (νopt; see selection diagram).
(HFAx, HFB, HFC)
200
VG 68
VG 46
VG
VG 32
VG 22
10
100
0
60
Continuous operation
40
36
νopt
20
16
10
Minimum permissible viscosity for short-term operation
7
−403) −25 −10 0 10 30 40 50 70 90 115
Temperature ϑ [°C]
1) This corresponds, for example on the VG 46, to a temperature 2) If the temperature at extreme operating parameters cannot be
range of +4 °C to +85 °C (see selection diagram) adhered to, please contact us.
3) For applications in the low-temperature range, please contact us.
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 7
Hydraulic fluids
355/370
– When operated at temperature and viscosity limits
when using mineral oil
1000
For the flushing flows stated, there is a pressure Maximum case pressure
differential of about 2 or 3 bar between port U pL absolute max 4 bar absolute
(including fitting) and the housing area (series 1x and
The parameters are reference values; under certain
series 3x, respectively).
operating conditions, restrictions may be required.
For version F (order position 09), the corresponding
flushing flows in accordance with data sheet 92053 must
Flow direction
be observed.
S to B
RE 92050/2023-06-15, Bosch Rexroth AG
8 A4VSO series 1x and 30 | Axial piston variable pump
Working pressure range
t2
Single operating period t1
Pressure p
tn
pnom
Maximum pressure pmax
∆t Nominal pressure pnom
Pressure p
∆p
Notice Time t
▶ Working pressure range applies when using
Total operating period = t1 + t2 + ... + tn
hydraulic fluids based on mineral oils. Please contact
us for values for other hydraulic fluids.
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 9
Technical data for sizes 40 to 1000
Maximum at Vg max2) nnom rpm 2600 2200 1800 1800 1500 1500 1500 1320 1200 1500 1000
rotational at Vg ≤ Vg max3) nmax rpm 3200 2700 2200 2100 1800 1700 1700 1600 1500 1500 1200
speed1)
Flow at nnom and Vg max qv l/min 104 156 225 324 375 532 532 660 900 1125 1000
Power at nnom, Vg max and P kW 61 91 131 189 219 311 323 385 525 656 583
Δp = 350 bar
at 1500 rpm P kW 35 62 109 158 219 311 323 3396) 4496) 656 –
at 1800 rpm P kW 42 74 131 189 262 – – – – – –
Torque at Vg max M max Nm 223 395 696 1002 1391 1976 2061 2783 4174 4174 5565
and Δp = 350 bar2)
and Δp = 100 bar2) M Nm 64 113 199 286 398 564 589 795 1193 1193 1590
Rotary Shaft end P c kNm/rad 80 146 260 328 527 800 800 1145 1860 1860 2730
stiffness of Shaft end Z c kNm/rad 77 146 263 332 543 770 770 1136 1812 1812 2845
drive shaft
Moment of inertia JTW kgm2 0.0049 0.0121 0.03 0.055 0.0959 0.19 0.19 0.3325 0.66 0.66 1.20
Maximum angular acceleration 4)
α rad/s² 17000 11000 8000 6800 4800 3600 3600 2800 2000 2000 1450
Case volume V l 2 2.5 5 4 10 8 8 14 19 22 27
Weight (without through drive) m kg 39 53 88 102 184 207 207 320 460 490 605
approx.
1.25
Rotational speed n / nnom
1.2
1.6
1.1 1.4
1.2
1.0 1.0
0.9 0.8
RE 92050/2023-06-15, Bosch Rexroth AG
10 A4VSO series 1x and 30 | Axial piston variable pump
Technical data for sizes 71, 250, 355, 370 and 500
Technical data for sizes 71, 250, 355, 370 and 500
1.1
Rotational speed
1.2
Inlet pressure
1.0 1.0
1.0 1.0
n / nnom
0.9
ps absolute
n / nnom
0.9 0.8
0.9 0.8
0.5 0.6 0.7 0.8 0.9 1.0
Displacement Vg/Vg max 0.6 0.7 0.8 0.9 1.0
Displacement Vg/Vg max
1.2
Inlet pressure ps absolute
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 11
Technical data for sizes 71, 250, 355, 370 and 500
3000
2900
Rotational speed nnom [rpm]
2700
Permissible
speed range
2500
2300
2100
0 30 50 100
Displacement Vg [%]
Notice
▶ Theoretical values, without efficiency and tolerances;
values rounded
▶ Operation above the maximum values or below the
minimum values may result in a loss of function,
a reduced service life or in the destruction of the
axial piston unit. We recommend checking loads
through tests or calculation/simulation and comparing
them with the permissible values.
▶ Special requirements apply in the case of belt drives.
Please contact us.
RE 92050/2023-06-15, Bosch Rexroth AG
12 A4VSO series 1x and 30 | Axial piston variable pump
Technical data for sizes 71, 250, 355, 370 and 500
maximum X/2 X/2 at X/2 Fq max N 1000 1200 1600 2000 2000 2200 2200 2500 3000 3500
X
Maximum
+
axial force Fax ± Fax max N 600 800 1000 1400 1800 2000 2000 2000 2200 2200
–
▼ Distribution of torques
Notice
▶ In case of through drive pumps as well as in case of M1 M2
bi-directional torque loads, the use of a splined shaft
is recommended.
▶ The through-drive torques apply to the through-drive
ME
shaft without hub:
Prepared for through drive, with pressure-resistant 1st pump 2nd pump M3
1) Values also apply for the version with charge pump (A4VSLO)
2) Efficiency not considered
3) For drive shafts with no radial force
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 13
Characteristic curves
Characteristic curves
150 75
n = 2600 min-1 400 n = 1800 min-1 200
n = 1500 min-1 n = 1500 min-1
Flow qv [l/min]
Flow qv [l/min]
50 25
200 Pqv max 100
Pqv Null
0 0
0 100 200 300 350 100 50
Working pressure p [bar] Pqv Null
▼ Size 71 0 0
0 100 200 300 350
150 150 Working pressure p [bar]
qv n = 2200 min-1
Flow qv [l/min]
n = 1500 min-1
0 0
0 100 200 300 350 qv
Working pressure p [bar] 300 150
Pqv max
▼ Size 125
200 100
300 150
n = 1800 min-1
Flow qv [l/min]
n = 1500 min-1
Drive power P [kw]
100 50
qv Pqv Null
200 100
Pqv max 0
0
100 50 0 100 200 300 350
Working pressure p [bar]
Pqv Null
0 0
0 100 200 300 350
Working pressure p [bar]
RE 92050/2023-06-15, Bosch Rexroth AG
14 A4VSO series 1x and 30 | Axial piston variable pump
Characteristic curves
500 250
500 250
qv
qv
200 100
200 100
0 0
0 0
0 100 200 300 350 0 100 200 300 350 380
Working pressure p [bar] Working pressure p [bar]
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 15
Characteristic curves
1100 550
800 400
n = 1200 min-1
n = 1320 min-1 n = 1000 min-1
1000 500
700 350
900 450
600 qv 300
qv
800 400
500 250
700 350
400 200
Pqv max
600 300
300 150
500 250
200 100
300 150
0 0
0 100 200 300 350
Working pressure p [bar]
200 100
Pqv Null
100 50
0 0
0 100 200 300 350
RE 92050/2023-06-15, Bosch Rexroth AG
16 A4VSO series 1x and 30 | Axial piston variable pump
Characteristic curves
▼ Size 1000
1600 800
n = 1200 min-1
n = 1000 min-1
1400 700
1200 600
qv
1000 500
800 400
Pqv max
600 300
400 200
0 0
0 100 200 300 350
Working pressure p [bar]
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 17
Overview of control devices
The pressure controller limits the maximum pressure at Suitable for pressure control of multiple axial piston units
the pump outlet within the control range of the variable A4VSO in parallel operation.
pump. The variable pump only supplies as much
hydraulic fluid as is required by the consumers. If the Optional:
working pressure exceeds the pressure command value at ▶ with flow control (DPF)1)
the pressure valve, the pump will regulate to a smaller
▼ Characteristic curve
displacement to reduce the control differential.
▶ Basic position in depressurized state: Vg max.
▶ Setting range for pressure control: 50 to 350 bar. p
Standard is 350 bar.
Optional:
▶ Pressure controller, remotely operated (DRG)1)
qv min
qv max
▼ Characteristic curve
p ▼ Circuit diagram
qv qv Mst
min max
XD
▼ Circuit diagram
B1 B MB
B1 B MB
U S MS K1 K2 T R(L)
U S MS K1 K2 T R(L)
RE 92050/2023-06-15, Bosch Rexroth AG
18 A4VSO series 1x and 30 | Axial piston variable pump
Overview of control devices
The flow controller adjusts the displacement of the pump to The pressure and flow controller is a combination of the
the volume required by the consumer. The flow of the pump DR pressure controller and FR flow controller.
is then dependent on the cross section of the external
▼ Characteristic curve
metering orifice (item 4), which is located between the pump
and the consumer. The flow is nearly independent of the
load pressure within the control range of the pump. 350
Pressure deviation ≤ 3 bar
Working pressure p [bar]
Initial position in depressurized state: Vg max
Mechanical minimum and maximum swivel angle limitation
▶ The Vg min stop is set so that a pressure of 15 to 20 bar
is set when port B is plugged.
▶ The Vg max stop is set to nominal Vg max. When ordering,
please state other setting values in plain text 50
(possible setting ranges Vg max to 50% Vg max).
qv min qv max
▼ Characteristic curve Flow
max
350 Circuit diagram, sample sizes 40 and 71
XF
4
14 min
0
qv min qv max
Flow B1 B MB
B1 B MB U S MS K1 K2 T R(L)
U S MS K1 K2 T R(L)
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 19
Overview of control devices
Power controller LR2 with hyperbolic characteristic curve Power controller LR3 with remotely controllable
(for further information, see data sheet 92064) power characteristic
(for further information, see data sheet 92064)
The hyperbolic power controller keeps the specified
drive power constant at the same drive speed. This hyperbolic power controller keeps the specified
drive power constant, whereby the power characteristic is
Optional: adjustable remotely.
▶ Pressure control (LR2D), remotely controllable (LR2G1));
▶ Flow control (LR2F1), LR2S1)) Optional:
▶ Hydraulic stroke limiter (LR2H); ▶ Pressure control (LR3D), remotely controllable (LR3G1));
▶ Mechanical stroke limiter (LR2Z); ▶ Flow control (LR3F1), LR3S1))
▶ Hydraulic two-point control (LR2Z); ▶ Hydraulic stroke limiter (LR3H);
▶ With electric unloading valve as starting aid (LR2Y). ▶ Mechanical stroke limiter (LR3Z);
▶ Hydraulic two-point control (LR3Z);
▼ Characteristic curve ▶ With electric unloading valve as starting aid (LR3Y).
▼ Characteristic curve
p
Vg min
Vg max
▼ Circuit diagram
RKV
RKV
XLR
B1 B MB
B1 B MB
U S MS K1 K2 T R(L)
U S MS K1 K2 T R(L)
RE 92050/2023-06-15, Bosch Rexroth AG
20 A4VSO series 1x and 30 | Axial piston variable pump
Overview of control devices
Hydraulic control LR2N and LR3N pilot-pressure related, Hydraulic control HD, pilot-pressure related
basic setting Vg min (for further information, see data sheet 92080)
(for further information, see data sheet 92064)
Stepless setting of the pump displacement according to
The displacement is adjusted proportionally to the pilot the pilot pressure. The control is proportional to the
pressure in PSt. specified pilot pressure (difference between pilot pressure
The additional hyperbola power controller is and case pressure).
superimposed on the pilot pressure signal and keeps the
specified drive power constant. Optional:
▶ Control characteristics (HD1, HD3)
Optional: ▶ Pressure control (HD.B),
▶ Power characteristics, remotely controllable (LR3N) ▶ Remote pressure control (HD.GB)
▶ Pressure control (LR.DN), ▶ Power control (HD1P)
▶ Remote pressure control (LR.GN1)) ▶ Electrical control of pilot pressure (HD1T)
▶ Electrical control of pilot pressure (LR, NT)
▼ Characteristic curve
▼ Characteristic curve
pSt
pSt
Vg
Vg
Vg max
Vg max
▼ Circuit diagram
p
P X2
Vg min
Vg max
▼ Circuit diagram
B1 B MB
Shown in switched position,
i.e. P pressurized
MSt
PSt U S MS K1 K2 T R(L)
B1 B MB
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 21
Overview of control devices
Stepless adjustment of displacement volume by means of Continuous control of displacement volume by means of
the electric motor control EM. a handwheel.
Various intermediate displacement values can be selected
with a programmed sequence control by means of built on ▼ Characteristic curve
Vg
S
Vg max
S max
▼ Circuit diagram
Vg
Vg max
B1 B MB
▼ Circuit diagram
B1 B MB
M
Poti
U S MS K1 K2 T R(L)
U S MS K1 K2 T R(L)
RE 92050/2023-06-15, Bosch Rexroth AG
22 A4VSO series 1x and 30 | Axial piston variable pump
Overview of control devices
Hydraulic control HM 1/2, volume-dependent Digital electro-hydraulic pump control system HS5.
(for further information, see data sheet 92076) (for detailed information see data sheet 92076)
The pump displacement is continuously adjustable The continuous displacement control is accomplished by
depending on the control fluid amount in ports X1 and X2. means of a proportional valve and electrical feedback of
Application: the swivel angle.
– 2-point circuit The HS5PP control system is equipped with a mounted
– Base device for servo or proportional controls pressure transducer, which means that it can be used for
electric pressure and power control.
▼ Circuit diagram
X2 X1 Optional:
B1 B MB ▶ Proportional valve (HS5);
▶ Short circuit valve (HSK, HS5K, HS5KP);
▶ For the den submerged oil insert (HS5M);
▶ With internal control pressure supply (HS5(E)V1));
▶ Control system with integrated digital
On Board Electronics OBE (HS5E).
▼ Characteristic curve
U ;p
U S MS K1 K2 T R(L) HD
Umax
Vg
Vg max
T P
b a
b a
B A
B1 B MB RKV SP
P
I S
P U
U S MS M1 R5 R6 R7 K1 K2 T R(L) R4 R3 R2 M2
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 23
Overview of control devices
Customer solution with proportional valve, Analog electro-hydraulic pump control system EO.
position transducer HM2C (for further information, see data sheet 92076)
(for further information, see data sheet 92076)
The continuous control of the displacement flow is
The HM2C customer solution provides the base unit, accomplished by means of a proportional valve and
sensors and actuators required for a control system. electrical feedback of the swivel angle. Thus, the control
This means that a pump control system can be built up by can be used as an electric displacement control.
the end users themselves for electronic volume,
pressure and power control. Optional:
The HM2C can be integrated freely in the control ▶ Control pressure range (EO1, EO2)
architecture of the plant operator machine with defined ▶ Short circuit valve (EO1K, EO2K)
standard interfaces. ▶ Without valves (EO1E, EO2E)
U
T P
b a Umax
a
b
B A G
U
Sp Vg
B1 B MB RKV
P Vg max
S
U
▼ Circuit diagram
b a
U S MS M1 R5 R6 R7 K1 K2 T R(L) R4 R3 R2 M2
SP
B1 B MB RKV
P
S
U
U S MS M1 K1 K2 T R(L) M2
RE 92050/2023-06-15, Bosch Rexroth AG
24 A4VSO series 1x and 30 | Axial piston variable pump
Overview of control devices
Secondary controlled rotational speed control DS.. Electrohydraulic control system DFE11)
(for further information, see data sheet 92057, 92059) (for further information, see data sheet 92088)
The rotational speed control DS2 and DS3 controls the An electrically actuated proportional valve controls the
secondary unit in such a manner, that this motor delivers power, pressure and swivel angle of the A4VSO...DFE1
sufficient torque to maintain the required rotational speed. variable pump. The current at the proportional valve
▶ This torque is determines the position of the swashplate angle and thus
– in the network with constant pressure the flow of the pump via the stroking piston and the
– proportional to the displacement volume and position transducer.
therefore proportional to the swivel angle. With the electric motor switched off and actuator system
depressurized, the pump swivels to maximum
▼ Characteristic curve displacement (Vg max) through spring force.
n (+)
▼ Characteristic curve
n2(min )-1
n2(min-1) p
n (-)
α
▼ Circuit diagram
▼ Circuit diagram
Consumer
Pressure transducer
P
I/U
T T B A P Pressure Analog
SP command value amplifier
B1 B MB RKV
P Power setpoint
U
S
B1
Scope of delivery
B MB
S
U
U S MS M1 K1 K2 T R(L) M2
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 25
Dimensions, size 40
Dimensions, size 40
Main dimensions only for the basic unit, further dimensions for the controls are given in the relevant data sheets.
R(L) 147
R(L)
(260)
18
140
135
K2 ø1
60 K1
150
B
ø15
80
85
91
T MB MS 150
8 52
X 45°
90 S 45°
227
266
Y
Valve mounting for
clockwise rotation
15 0 15
LR
30
79
80
R(L)
30 U
Valve mounting for
144 25
counter-clockwise rotation
Y
View Y View X
ø20.5
⌀40
69.9
50.8
B (B1) S
23.8 35.7
RE 92050/2023-06-15, Bosch Rexroth AG
26 A4VSO series 1x and 30 | Axial piston variable pump
Dimensions, size 40
58
56 36
M10 x 1.51) 2)
22 22
1.5 Shaft key width 10 7.5
+0.018
ø32+0.002
M101)2)
35-0.2
ø40
28
68
46
1) Center bore according to DIN 332 6) Depending on the installation position T, K1, K2 or R(L) must be
2) Thread according to DIN 13 connected (see also installation instructions on pages 75
3) Depending on the application, momentary pressure peaks can occur. and 77)
Keep this in mind when selecting measuring devices and fittings. 7) O = Must be connected (plugged on delivery)
4) Metric fastening thread is a deviation from standard. X = Plugged (in normal operation)
5) The countersink may be deeper than specified in the standard. 8) Plugged with flange plate
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 27
Dimensions, size 71
Dimensions, size 71
Main dimensions only for the basic unit, further dimensions for the controls are given in the relevant data sheets.
R(L) R(L)
(298)
18
157
154
K2 ø1
80
K1
170
B
ø15
92.5
106
97
T MB MS
170
8 61
X S 45°
101 45°
254
295
Flange B1
For notes on B1 see type code item 12
ISO 3019-2
92.5
ø140-0.063
LR
15 0 15
34
92.5
92
R(L)
U
27 Valve mounting for
166 27
counter-clockwise rotation
Y
View Y View X
57.2
77.8
⌀50
ø25
B (B1) S
27.8
42.9
RE 92050/2023-06-15, Bosch Rexroth AG
28 A4VSO series 1x and 30 | Axial piston variable pump
Dimensions, size 71
70
68
46
28
28
1.5 Shaft key width 12
M121)2)
+0.018
ø40 +0.002
M121)2)
43-0.2
80 55
1) Center bore according to DIN 332 6) Depending on the installation position T, K1, K2 or R(L) must be
2) Thread according to DIN 13 connected (see also installation instructions on pages
3) Depending on the application, momentary pressure peaks can occur. 75 and 77)
Keep this in mind when selecting measuring devices and fittings. 7) O = Must be connected (plugged on delivery)
4) Metric fastening thread is a deviation from standard. X = Plugged (in normal operation)
5) The countersink may be deeper than specified in the standard. 8) Plugged with flange plate
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 29
Dimensions, size 125
Main dimensions only for the basic unit, further dimensions for the controls are given in the relevant data sheets.
R(L) R(L)
(354)
22
191
186
K2 ⌀2 K1
00
200
B
114.5
112.5
121
⌀20
MB MS
T 200
8 70
45°
125 X S 45°
310
355
Y
Valve mounting for
clockwise rotation
Flange M2 B1 For notes on B1 see type code item 12
ISO 3019-2
112.5
-0.063
LR
15 0 15
ø160
50
112.5
112
R(L)
U B
M1
33 14 14
Valve mounting for
203
counter-clockwise rotation
Location R(L) for HD and EP control Y
View Y View X
⌀31
66.7
88.9
⌀63
B (B1) S
31.8
50.8
RE 92050/2023-06-15, Bosch Rexroth AG
30 A4VSO series 1x and 30 | Axial piston variable pump
Dimensions, size 125
82
80
36 54
M161)2)
+0.021
ø50+0.002
M161)2)
53.5-0.2
92
64
1) Center bore according to DIN 332 6) Depending on the installation position T, K1, K2 or R(L) must be
2) Thread according to DIN 13 connected (see also installation instructions on pages 75
3) Depending on the application, momentary pressure peaks can occur. and 77)
Keep this in mind when selecting measuring devices and fittings. 7) O = Must be connected (plugged on delivery)
4) Metric fastening thread is a deviation from standard. X = Plugged (in normal operation)
5) The countersink may be deeper than specified in the standard. 8) Plugged with flange plate
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 31
Dimensions, size 180
Main dimensions only for the basic unit, further dimensions for the controls are given in the relevant data sheets.
R(L) R(L)
(354)
22
191
186
K2 K1
ø20
0
200
B
114.5
121
116
ø20
T MS S MB 200
8 70
45°
125 X 45°
318
375
Y
Valve mounting for
clockwise rotation
LR
15 0 15
50
112
120
R(L)
U B
33 M1
14 14 Valve mounting for
203 counter-clockwise rotation
View Y View X
106.4
66.7
ø31
ø75
B (B1) S
31.8
61.9
RE 92050/2023-06-15, Bosch Rexroth AG
32 A4VSO series 1x and 30 | Axial piston variable pump
Dimensions, size 180
82
80
36 54
M161)2)
+0.021
ø50 +0.002
M161)2)
53.5-0.2
92
64
1) Center bore according to DIN 332 6) Depending on the installation position T, K1, K2 or R(L) must be
2) Thread according to DIN 13 connected (see also installation instructions on pages 75
3) Depending on the application, momentary pressure peaks can occur. and 77)
Keep this in mind when selecting measuring devices and fittings. 7) O = Must be connected (plugged on delivery)
4) Metric fastening thread is a deviation from standard. X = Plugged (in normal operation)
5) The countersink may be deeper than specified in the standard. 8) Plugged with flange plate
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 33
Dimensions, size 250
Main dimensions only for the basic unit, further dimensions for the controls are given in the relevant data sheets.
R(L) R(L)
(426)
30
238
233
⌀2
K2 80 K1
265
B
145
144
153
ø24
T MB S MS 265
8 90
150 45°
X
380
435
Y
Valve mounting for
clockwise rotation
Flange
M2 B1 For notes on B see type code item 12
ISO 3019-2 1
144
⌀224 -0.072
LR
15 0 15
55
144
144
R(L)
U M1 B
43 17 17
248 Valve mounting for
counter-clockwise rotation
Location R(L) for HD and EP control Y
View Y View X
106.4
⌀75
79.4
⌀40
B (B1) S
36.5
61.9
RE 92050/2023-06-15, Bosch Rexroth AG
34 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions, size 250
105
100
70
42
Shaft key width 18 42
3
M201)2)
M201)2)
+0.011
ø60 +0.030
64-0.2
115
80
1) Center bore according to DIN 332 6) Depending on the installation position T, K1, K2 or R(L) must be
2) Thread according to DIN 13 connected (see also installation instructions on pages 75
3) Depending on the application, momentary pressure peaks can occur. and 77)
Keep this in mind when selecting measuring devices and fittings. 7) O = Must be connected (plugged on delivery)
4) Metric fastening thread is a deviation from standard. X = Plugged (in normal operation)
5) The countersink may be deeper than specified in the standard. 8) Plugged with flange plate
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 35
Dimensions size 355 and size 370
Main dimensions only for the basic unit, further dimensions for the controls are given in the relevant data sheets.
R(L) R(L)
(424)
30
238
233
K2 ⌀2 K1
80
265
B
144.5
144
153
⌀24
MS S MB
T 265
45°
8 90 45°
150 X
393
464
LR
15 0 15
⌀224
55
144
148
R(L)
U M1 B
40 17 17
248 Valve mounting for
counter-clockwise rotation
Y
Location R(L) for HD and EP control
View X
View Y
⌀100
130.2
79.4
⌀40
B (B1)
S
36.5 77.8
RE 92050/2023-06-15, Bosch Rexroth AG
36 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions size 355 and size 370
105
82
M20 x 2.51) 2)
100
42 42
4.5 Shaft key width 20 15
+0.030
ø70+0.011
74.5-0.2
M201)2)
ø72
69
115
92
1) Center bore according to DIN 332 6) Depending on the installation position T, K1, K2 or R(L) must be
2) Thread according to DIN 13 connected (see also installation instructions on pages 75
3) Depending on the application, momentary pressure peaks can occur. and 77)
Keep this in mind when selecting measuring devices and fittings. 7) O = Must be connected (plugged on delivery)
4) Metric fastening thread is a deviation from standard. X = Plugged (in normal operation)
5) The countersink may be deeper than specified in the standard. 8) Plugged with flange plate
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 37
Dimensions, size 500
Main dimensions only for the basic unit, further dimensions for the controls are given in the relevant data sheets.
R(L) R(L)
(510)
16+5
11
283
280
190
K2
⌀
K1
36
0
B
5
180
40
190
⌀
ø24
8x
45
45
(=
°
36
°
T MB MS 0° 22°
S ) 30'
80
47 155 X
441 190 190
520
16 U M2
B1 For notes on B1 see type code item 12
189
158
⌀315 -0.081
⌀230+5
⌀228
LR
15 0 15
50
R(L)
158
M1 B
Flange 30
ISO 3019-2 279 50 Valve mounting for
counter-clockwise rotation
Y
View Y View X
⌀125
152.4
⌀50
96.8
B (B1) S
44.5
92.1
RE 92050/2023-06-15, Bosch Rexroth AG
38 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions, size 500
130
125
90
42
Shaft key width 22 42
3
M201)2)
M201)2)
+0.030
ø80+0.011
85-0.2
180
140
1) Center bore according to DIN 332 6) Depending on the installation position T, K1, K2 or R(L) must be
2) Thread according to DIN 13 connected (see also installation instructions on pages 75
3) Depending on the application, momentary pressure peaks can occur. and 77)
Keep this in mind when selecting measuring devices and fittings. 7) O = Must be connected (plugged on delivery)
4) Metric fastening thread is a deviation from standard. X = Plugged (in normal operation)
5) The countersink may be deeper than specified in the standard. 8) Plugged with flange plate
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 39
Dimensions, size 750
Main dimensions only for the basic unit, further dimensions for the controls are given in the relevant data sheets.
R(L) R(L)
(582)
16+5
13
322
317
232
MB K2 K1
⌀
200
49
45
232
⌀
⌀22
8x
45
45
T (=
°
°
MS 36
S 0° 22°
30'
89 )
X
47 161
473 232 232
560
16 U M2
B1 For notes on B1 see type code item 12
231
182
⌀400 -0.089
⌀263+5
⌀255
LR
15 0 15
50
182
R(L)
M1 B
Flange 32
ISO 3019-2 301 50 Valve mounting for
Y counter-clockwise rotation
View Y View X
152.4
⌀125
⌀50
96.8
B (B1) S
44.5
92.1
RE 92050/2023-06-15, Bosch Rexroth AG
40 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions, size 750
130
125
105
50
Shaft key width 25 50
4.5
M241)2)
M241)2)
+0.035
ø90+0.013
95-0.2
180
155
1) Center bore according to DIN 332 6) Depending on the installation position T, K1, K2 or R(L) must be
2) Thread according to DIN 13 connected (see also installation instructions on pages 75
3) Depending on the application, momentary pressure peaks can occur. and 77)
Keep this in mind when selecting measuring devices and fittings. 7) O = Must be connected (plugged on delivery)
4) Metric fastening thread is a deviation from standard. X = Plugged (in normal operation)
5) The countersink may be deeper than specified in the standard. 8) Plugged with flange plate
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 41
Dimensions of size 750 with charge pump (impeller)
Main dimensions only for the basic unit, further dimensions for the controls are given in the relevant data sheets.
R(L) R(L)
(582)
16+5
13 MB
322
317
232
K2 K1
95
210
ø4
232
50
ø4
ø22
8x
45
45
T (=
°
°
ML 36
S 0° 22°
) 30'
89
X
47 161
457 232 232
530
614
640
182
ø400 -0.089
ø263+5
ø255
LR
15 0 15
50
182
R(L)
M1 B
Flange 32
ISO 3019-2 301 50
Valve mounting for
Y
counter-clockwise rotation
View Y View X MS
B1
152.4
ø125
96.8
ø50
B (B1) S
44.5
92.1
RE 92050/2023-06-15, Bosch Rexroth AG
42 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions of size 750 with charge pump (impeller)
130
125 105
50 50
Shaft key width 25
M241)2)
4.5
M241)2)
+0.035
ø90+0.013
95-0.2
180 155
1) Center bore according to DIN 332 6) Depending on the installation position T, K1, K2 or R(L) must be
2) Thread according to DIN 13 connected (see also installation instructions on pages 75
3) Depending on the application, momentary pressure peaks can occur. and 77)
Keep this in mind when selecting measuring devices and fittings. 7) O = Must be connected (plugged on delivery)
4) Metric fastening thread is a deviation from standard. X = Plugged (in normal operation)
5) The countersink may be deeper than specified in the standard. 8) Plugged with flange plate
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 43
Dimensions, size 1000
Main dimensions only for the basic unit, further dimensions for the controls are given in the relevant data sheets.
R(L) R(L)
(622)
16+5
13
344
350
232
ø4
MB K2 50
K1
95
225
ø4
ø22
8x
45
45
T (=
°
°
36
S MS 0° 22°
) 30'
98
47 203 X
548 232 232
633
210
ø400 -0.089
ø333+5
ø322
LR
15 0 15
55
210
R(L)
MB
Flange M1 B
ISO 3019-2 35
360 51
Valve mounting for
Y
counter-clockwise rotation
View Y View X
B (B1)
152.4
ø125
96.8
ø50
S
44.5
44.5
92.1
96.8
RE 92050/2023-06-15, Bosch Rexroth AG
44 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions, size 1000
165
160
105
50
Shaft key width 28 50
4.5
M241)2)
+0.035
ø100+0.013
M241)2)
106-0.2
215
155
1) Center bore according to DIN 332 6) Depending on the installation position T, K1, K2 or R(L) must be
2) Thread according to DIN 13 connected (see also installation instructions on pages 75
3) Depending on the application, momentary pressure peaks can occur. and 77)
Keep this in mind when selecting measuring devices and fittings. 7) O = Must be connected (plugged on delivery)
4) Metric fastening thread is a deviation from standard. X = Plugged (in normal operation)
5) The countersink may be deeper than specified in the standard. 8) Plugged with flange plate
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 45
Dimensions, through drive
Flange ISO 3019-2 (metric) Hub for splined shaft2) Availability across sizes Code
355
Diameter Symbol Diameter 40 71 125 180 250 500 750 1000
370
125-4 N32×2×14×8H ● ● – – – – ● ● ○ K31
N32×2×14×8H – – ● ● ● ● – – – U31
▼ 125-4 ▼ 125-4
+0.05
ø125 +0.02
A6
60 60
ø1 ø1
45º 45
º
A4 A4
A1 (to mounting flange) A5 A1 (to mounting flange)
N N
RE 92050/2023-06-15, Bosch Rexroth AG
46 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions, through drive
355
Diameter Symbol Diameter 40 71 125 180 250 500 750 7504) 1000
370
▼ 140-4 ▼ 140-4
+0.07
ø140 +0.02
+0.05
ø140 +0.02
A6
80 80
ø1 ø1
45º 45
º
A4 A4
A1 (to mounting flange) A5 A1 (to mounting flange)
N N
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 47
Dimensions, through drive
▼ 160-4 ▼ 160-4
+0.02
+0.07
+0.05
ø160 +0.02
ø160
00 00
ø2 ø2
45º 45 A4
A4 º
A1 (to mounting flange) A1 (to mounting flange)
N N
RE 92050/2023-06-15, Bosch Rexroth AG
48 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions, through drive
▼ 224-4 ▼ 224-4
Section M-N
Section M-N
M A3 A2 M A3 A2
A7 A7
1)
1)
+0.03
+0.10
+0.03
+0.10
ø224
ø224
80 80
ø2 ø2
45 A4 45 A4
º º
A1 (to mounting flange) A1 (to mounting flange)
N N
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 49
Dimensions, through drive
▼ 224-4 ▼ 224-4
+0.10
ø224 +0.03
+0.03
ø224 +0.10
80 80
ø2 ø2
45 A4 45 A4
º º
A1 (to mounting flange) A1 (to mounting flange)
N N
RE 92050/2023-06-15, Bosch Rexroth AG
50 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions, through drive
▼ 315-8 ▼ 315-8
M A3 A2 1) M A3 A2 1)
A7 A7
A7
+0.03
ø315 +0.10
+0.03
ø400 +0.10
60 50
ø3 ø4
8×4
8×4
45 45
5º
5º
(= º
36 º (=
36
0º A4 0º A4
) 22º30 22º30
´ ) ´
A1 (to mounting flange) A1 (to mounting flange)
N N
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 51
Dimensions, through drive
▼ 400-8
Section M-N
M A3 A2 1)
A7
A7
+0.03
ø400 +0.10
50
ø4
8×4
45
5º
(= º
36
0º 22º30 A4
) ´
A1 (to mounting flange)
N
K88 NG A1 A2 A3 A4 A73)
1000 728 53 99 19 M20; 26 deep
RE 92050/2023-06-15, Bosch Rexroth AG
52 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions, through drive
▼ 80-2 ▼ 80-2
Section M-N
Section M-N
M A3 A2
A8 M A2
A8 A3
1) 1)
+0.02
ø80 +0.05
+0.02
ø80 +0.05
A7
A7
ø109
ø109
45 A4
º 45 A4
º
A1 (to mounting flange) A5
A1 (to mounting flange)
N
N
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 53
Dimensions, through drive
▼ 100-2 ▼ 100-2
+0.05
ø100 +0.02
+0.05
ø100 +0.02
A7
ø140 ø140
45 A4 45 A4
º º
A1 (to mounting flange) A5 A1 (to mounting flange)
N N
RE 92050/2023-06-15, Bosch Rexroth AG
54 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions, through drive
▼ 100-2 ▼ 100-2
1)
1)
+0.05
ø100 +0.02
+0.05
ø100 +0.02
A7
ø140 ø140
45 A4 45 A4
º º
A1 (to mounting flange) A5 A1 (to mounting flange)
N N
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 55
Dimensions, through drive
▼ 125-4
Section M-N
M
A3 A2
45° 45°
1)
A7
ø1
60
+0.05
ø125 +0.02
N
A4
A1 (to mounting flange)
KE1 NG A1 A2 A3 A4 A73)
71 316 20.8 27.5 10 M12; 24 deep
RE 92050/2023-06-15, Bosch Rexroth AG
56 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions, through drive
355
Diameter Symbol Diameter 40 71 125 180 250 370 500 750 7504) 1000
125-2 1 1/4 in 14T 12/24DP – ● – – – – ● ○ ● ○ KB5
, 1 1/4 in 14T 12/24DP – – ● ● ● ● – – – – UB5
▼ 125-2 ▼ 125-2
Section M-N
Section M-N
M NG 500 A7 M A3 A2
A3 A2
NG 500 5) A7
1)
and 750 1)
ø125 +0.02
+0.05
+0.05
ø125 +0.02
80
ø1
45 A4
º NG 500 ø180
A1 (to mounting flange)
45 A4
º
N A1 (to mounting flange)
1) Mounting bolts and O-ring seal are included in the scope of 5) For NG71 with intermediate plate
delivery
2) Involute spline according to ANSI B92.1a, 30° pressure angle,
flat root, side fit, tolerance class 5
3) Thread according to DIN 13
4) With charge pump
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 57
Dimensions, through drive
▼ 125-2 ▼ 160-4
+0.05
ø160 +0.02
80 00
ø1 ø2
45 45 A4
º A4 º
RE 92050/2023-06-15, Bosch Rexroth AG
58 A4VSO series 1x and 30 | Axial piston variable pump
Dimensions, through drive
▼ 180-4 ▼ 180-4
M A7 M A7
1) 1)
+0.02
ø180 +0.07
+0.02
ø180 +0.05
24 24
ø2 ø2
45 45
º º
A4 A4
N A1 (to mounting flange) N A1 (to mounting flange)
500 530 10.4 63.6 10 M16; 25 deep 180 406 10.6 62 9 M16; 34 deep
750 580 10.4 63.6 10 M16; 25 deep 250 453 10.6 64 9 M16; 22 deep
355 482 10.6 64 9 M16; 22 deep
370
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 59
Dimensions, through drive
Flange ISO 3019-1 (SAE) Hub for splined shaft2) Availability across sizes Code
355
Diameter Symbol Diameter 40 71 125 180 250 370 500 750 7504) 1000
▼ 82-2 ▼ 82-2
Section M-N
Section M-N
A3 A2
A3 A2
M
A8 M A7
+0.02
ø82.55 +0.05
+0.02
+0.05
ø82.55
A7
only for 1) 1)
NG 40,
500 and
ø106.5 ø106.5
750
45 A4 45 A4
º º
A1 (to mounting flange) A5 A1 (to mounting flange)
N
N
40 263 10.4 25.9 10 – – M10; 15 deep 125 369 10.3 19.4 13 M10; 16 deep
71 291 10.3 24.6 10 2 140 M10; 15 deep 180 393 10.3 19.4 13 M10; 16 deep
500 505 10.3 32.7 10 15 240 M10; 15 deep 250 453 16 19.4 13 M10; 16 deep
750 555 10.3 32.7 10 – – M10; 15 deep 355 482 16 19.4 13 M10; 16 deep
370
RE 92050/2023-06-15, Bosch Rexroth AG
60 A4VSO series 1x and 30 | Axial piston variable pump
Dimensions, through drive
Flange ISO 3019-1 (SAE) Hub for splined shaft2) Availability across sizes Code
355
Diameter Symbol Diameter 40 71 125 180 250 370 500 750 1000
▼ 82-2 ▼ 82-2
A3 A2 A3 A2
Only for NG 40 M M
A7
+0.02
ø82.55 +0.05
A7
+0.02
ø82.55 +0.05
1)
1)
ø106.5 ø106.5
45 45 A4
º A4 º
A1 (to mounting flange) A1 (to mounting flange)
N N
40 263 19.5 21 10 M10; 15 deep 125 369 19.4 21.1 10 M10; 16 deep
71 312.5 21.5 19 10 M10; 20 deep 180 393 19.4 21.1 10 M10; 16 deep
250 453 19.5 23.9 10 M10; 16 deep
355 482 19.4 23.9 10 M10; 16 deep
370
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 61
Dimensions, through drive
Flange ISO 3019-1 (SAE) Hub for splined shaft2) Availability across sizes Code
355
Diameter Symbol Diameter 40 71 125 180 250 370 500 750 7504) 1000
▼ 101-2 ▼ 101-2
Section M-N
Section M-N
A3 A2 A3 A2
M M
A8 A7
1) 1)
+0.05
ø101.6 +0.02
+0.05
ø101.6 +0.02
A7
only for
ø146 ø146 NG 125
45 A4 and 180 A4
º 45
º
A1 (to mounting flange) A5 A1 (to mounting flange)
N N
40 290 20.4 23.1 10 – – M12; 18 deep 125 369 18.5 25 13 M12; 22 deep
71 322 20.5 23.1 10 – – M12; 30 deep 180 393 18.5 25 13 M12; 22 deep
500 505 19.5 25 10 15 240 M12; 18 deep 250 453 19.5 23.1 13 M12; 18 deep
750 555 19.5 25 10 – – M12; 18 deep 355 482 19.5 23.1 13 M12; 18 deep
370
7504) 649 19.5 25 10 – – M12; 18 deep
RE 92050/2023-06-15, Bosch Rexroth AG
62 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions, through drive
Flange ISO 3019-1 (SAE) Hub for splined shaft2) Availability across sizes Code
355
Diameter Symbol Diameter 40 71 125 180 250 370 500 750 1000
▼ 101-2 ▼ 101-2
1) 1)
+0.05
ø101.6 +0.02
+0.05
ø101.6 +0.02
A7
only for
ø146 ø146 NG 125
45 A4 and 180
º 45 A4
º
A1 (to mounting flange) A5 A1 (to mounting flange)
N N
40 290 20.8 27.5 10 – – M12; 20 deep 125 369 18.9 29.4 13 M12; 22 deep
71 322 20 29.4 10 – – M12; 30 deep 180 393 18.9 29.4 13 M12; 22 deep
500 505 20.4 28.9 10 15 240 M12; 18 deep 250 453 18.9 29.4 13 M12; 18 deep
355 482 18.9 29.4 13 M12; 18 deep
370
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 63
Dimensions, through drive
▼ 101-24)
Section M-N
M A3 A2
1)
A8
+0.05
ø101.6 +0.02
A7
146
A4
45
º
A1 (to mounting flange)
K06 NG A1 A2 A3 A4 A7 A83)
RE 92050/2023-06-15, Bosch Rexroth AG
64 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions, through drive
Flange ISO 3019-1 (SAE) Hub for splined shaft2) Availability across sizes Code
355
Diameter Symbol Diameter 40 71 125 180 250 370 500 750 1000
▼ 127-44) ▼ 127-4
A7 A7
1)
ø1
62
+0.05
ø127 +0.02
+0.05
ø127 +0.02
62
ø1
N 45
º
A4 A4
A1 (to mounting flange) A1 (to mounting flange)
N
71 321 19 29.4 13 M12; 30 deep 125 369 19.9 29.5 13 M12; 22 deep
180 393 19.9 29.5 13 M12; 22 deep
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 65
Dimensions, through drive
Flange ISO 3019-1 (SAE) Hub for splined shaft2) Availability across sizes Code
355
Diameter Symbol Diameter 40 71 125 180 250 370 500 750 1000
▼ 127-44) ▼ 127-4
A7 A7
1)
ø1
62
+0.05
ø127 +0.02
+0.05
ø127 +0.02
62
ø1
N 45
º
A4 A4
A1 (to mounting flange) A1 (to mounting flange)
N
RE 92050/2023-06-15, Bosch Rexroth AG
66 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions, through drive
▼ 127-2 ▼ 127-2
+0.02
ø127 +0.05
+0.02
ø127 +0.05
ø181 ø181
45 A4 45 A4
º º
A1 (to mounting flange) A5 A1 (to mounting flange)
N N
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 67
Dimensions, through drive
▼ 127-2 ▼ 127-2
+0.02
ø127 +0.05
+0.02
ø127 +0.05
ø181 ø181
45 A4 45 A4
º º
A1 (to mounting flange) A5 A1 (to mounting flange)
N N
500 505 10.3 56.7 13 M16; 24 deep 125 369 10.4 50 13 M16; 22 deep
750 555 10.3 56.7 13 M16; 24 deep 180 393 10.4 50 13 M16; 22 deep
1000 628 10.4 56.6 13 M16; 32 deep 250 453 12.4 55 13 M16; 22 deep
355 482 12.4 55 13 M16; 22 deep
370
RE 92050/2023-06-15, Bosch Rexroth AG
68 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions, through drive
▼ 152-4
M Section M-N
A7 A3 A2
1)
+0.05
ø152.4 +0.02
8.5
ø22
45º
A4
U96 NG A1 A2 A3 A4 A73)
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 69
Dimensions, through drive
Flange ISO 3019-1 (SAE) Hub for splined shaft2) Availability across sizes Code
355
Diameter Symbol Diameter 40 71 125 180 250 370 500 750 1000
▼ 152-4 ▼ 152-4
+0.02
+0.05
+0.02
+0.05
ø152.4
ø152.4
8.5 8.5
ø22 ø22
45º 45
º
A4 A4
500 530 10.4 59.6 13 M16; 25 deep 125 382 10.4 62 13 M16; 35 deep
750 580 10.4 59.6 13 M16; 25 deep 180 406 10.4 62 13 M16; 35 deep
250 453 10.6 62 13 M16; 22 deep
355 482 10.6 62 13 M16: 22 deep
370
RE 92050/2023-06-15, Bosch Rexroth AG
70 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Dimensions, through drive
Flange ISO 3019-1 (SAE) Hub for splined shaft2) Availability across sizes Code
355
Diameter Symbol Diameter 40 71 125 180 250 370 500 750 1000
▼ 165-4
Section M-N
A7 A3 A2
M
1)
+0.03
ø165.1 +0.10
7.5
ø31
45
º
A4
K84 NG A1 A2 A3 A4 A73)
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 71
Dimensions, through drive
Flange ISO 3019-1 (SAE) Hub for splined shaft2) Availability across sizes Code
355
Diameter Symbol Diameter 40 71 125 180 250 370 500 750 1000
▼ ø63 ▼ ø63
28.3+0.2
28.3+0.2
45º
1) 45º 1)
+0.05
ø63+0.02
+0.05
ø63+0.02
ø80
ø80
A7
A7
ø25H7
ø25H7
45º N
A4 A4
A1 (to mounting flange) A1 (to mounting flange)
N
RE 92050/2023-06-15, Bosch Rexroth AG
72 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Overview of mounting options
Bosch Rexroth AG, RE 92050/2023-06-15
Dimensions [mm] Axial piston variable pump | A4VSO series 1x and 30 73
Permissible mass moment of inertia
m1 m2 m3
l1
(A1) (l1)
l2
l3
1
Mm = (m1× l1+ m2× l2+ m3× l3) × [Nm]
102
RE 92050/2023-06-15, Bosch Rexroth AG
74 A4VSO series 1x and 30 | Axial piston variable pump Dimensions [mm]
Combination pumps A4VSO + A4VSO
Total length A
A4VSO A4VSO...DR...N00 (2nd pump)
(1st pump) NG 40 NG 71 NG 125 NG 180 NG 250 NG 355 NG 370 NG 500 NG 750 NG 1000
NG 40 554 – – – – – – – – –
NG 71 582 611 – – – – – – – –
NG 125 635 664 724 – – – – – – –
NG 180 659 688 748 768 – – – – – –
NG 250 719 748 808 828 904 – – – – –
NG 355 748 777 837 857 933 962 – – – –
NG 370 748 777 837 857 933 962 – – – –
NG 500 771 800 860 880 976 1005 1005 1110 – –
NG 750 821 850 910 930 1026 1055 1055 1160 1214 –
NG 1000 ○ 923 983 1003 1099 1128 1128 1233 1288 1368
○ = On request
Notice
▶ The combination pump type code is shown in
shortened form in the order confirmation.
A
Example:
A4VSO 250LR2D/30R+A4VSO 250LR2D/30R
▶ Each through drive is plugged with
a non–pressure-resistant cover. Therefore, the units
must be fitted with a pressure-resistant cover or
a specified attachment pump before commissioning.
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 75
Installation instructions
Installation instructions
General Notice
The axial piston unit must be filled with hydraulic fluid In certain installation positions, an influence on the
and air bled during commissioning and operation. adjustment or control can be expected.
This must also be observed following a longer standstill as Gravity, dead weight and case pressure can cause minor
the axial piston unit may empty via the hydraulic lines. characteristic shifts and changes in actuating time.
Particularly in the installation position "drive shaft
upwards," filling and air bleeding must be carried out Installation position
completely as there is, for example, a danger of See the following examples 1 to 7.
dry running. Further installation positions are available upon request.
The leakage in the housing area must be directed to the Recommended installation positions: 1 and 2
reservoir via the highest drain port (T, K1, K2, R(L)).
Key
For combination pumps, the leakage must be drained off
R(L) Filling / Air bleeding
at each single pump. (F)
If a shared drain line is used for several units, make sure S Suction port
that the respective case pressure in each unit is not T Drain port
exceeded. The shared drain line must be dimensioned to U Flushing port
ensure that the maximum permissible case pressure of all K 1, K 2 Flushing port
connected units is not exceeded in any operating SB Baffle (baffle plate)
condition, particularly at cold start. If this is not possible, ht min Minimum required immersion depth (200 mm)
separate drain line must be laid, if necessary. hmin Minimum required distance to reservoir bottom (100 mm)
To prevent the transmission of structure-borne noise, hS max Maximum permissible suction height (800 mm)
use elastic elements to decouple all connecting lines from all
vibration-capable components (e.g. reservoir, frame parts).
Notice
Under all operating conditions, the suction lines and the
drain lines must flow into the reservoir below the minimum Port F is part of the external piping and must be
fluid level. The permissible suction height hS results from provided on the customer side to make filling and air
the total pressure loss. However, it must not be higher than bleeding easier.
RE 92050/2023-06-15, Bosch Rexroth AG
76 A4VSO series 1x and 30 | Axial piston variable pump
Installation instructions
F ▼ Installation position 4
SB
ht min Air bleed Filling
hmin
R(L) (F) R(L) (F)
R(L)
F
R(L)
T S
T S
▼ Installation position 2
hs max
Air bleed Filling ht min SB
hmin
T (F) S + T (F)
F ▼ Installation position 5
SB
ht min
Air bleed Filling
hmin
T (F) T + U (F)
T S
T U
F
R(L)
R(L)
hs max S
▼ Installation position3
ht min
Air bleed Filling hmin
T + U (F) S + T + U (F)
F
SB
ht min
hmin
U
R(L) T
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 77
Installation instructions
RE 92050/2023-06-15, Bosch Rexroth AG
78 A4VSO series 1x and 30 | Axial piston variable pump
Project planning notes
▶ The axial piston variable pump A4VSO is intended to ▶ The pressure control (hydraulic or electronic) is not
be used in an open circuit. an adequate safeguard against pressure overload.
▶ The project planning, installation and commissioning Therefore, a pressure relief valve must be provided in
of the axial piston unit requires the involvement of the hydraulic system (integrated into the pump or
skilled personnel. externally in the system). In this connection,
▶ Before using the axial piston unit, please read the observe the technical limits of the pressure relief valve.
corresponding instruction manual completely and ▶ For controllers requiring external pilot pressure,
thoroughly. If necessary, this can be requested from sufficient control fluid must be provided to the
Bosch Rexroth. associated ports to ensure the required pilot pressures
▶ Before finalizing your design, please request a binding for the respective controller function. These controllers
installation drawing. are subject to leakage due to their design. An increase
▶ The specified data and notes contained herein must in control fluid demand has to be anticipated over the
be observed. total operating time. The design of the control fluid
▶ Depending on the operating conditions of the supply must thus be sufficiently large. If the control
axial piston unit (working pressure, fluid temperature), fluid is too low, the respective controller function may
the characteristic curve may shift. be impaired and undesired system behavior may result.
▶ The characteristic curve may also shift due to the dither ▶ For drives that are operated for a long period of time
frequency or control electronics. with constant rotational speed, the natural frequency
▶ Preservation: Our axial piston units are supplied as of the hydraulic system can be stimulated by the
standard with preservation protection for a maximum excitation frequency of the pump (rotational speed
of 12 months. If longer preservation protection is frequency x 9). This can be prevented with suitably
required (maximum 24 months), please specify this in designed hydraulic lines.
plain text when placing your order. The preservation ▶ Please note the details regarding the tightening torques
periods apply under optimal storage conditions, of port threads and other threaded joints in the
details of which can be found in the data sheet 90312 instruction manual.
or the instruction manual. ▶ The ports and fastening threads are designed for the
▶ Not all versions of the product are approved for use pmax permissible pressures of the respective ports,
in safety functions according to ISO 13849. see the connection tables. The machine or system
Please consult the proper contact at Bosch Rexroth manufacturer must ensure that the connecting
if you require reliability parameters (e.g., MTTFd) elements and lines correspond to the specified
for functional safety. conditions of use (pressure, flow, hydraulic fluid,
▶ Depending on the type of control used, temperature) with the necessary safety factors.
electromagnetic effects can be produced when using ▶ The service ports and function ports are only intended
solenoids. Applying a direct voltage signal (DC) to accommodate hydraulic lines.
to solenoids does not create electromagnetic
interference (EMI) nor is the solenoid affected by EMI.
Electromagnetic interference (EMI) potential exists
when operating and controlling a solenoid with
a modulated direct voltage signal (e.g. PWM signal)
Appropriate testing and measures should be taken by
the machine manufacturer to ensure other components
or operators (e.g. with pacemaker) are not affected
by this potential.
Bosch Rexroth AG, RE 92050/2023-06-15
Axial piston variable pump | A4VSO series 1x and 30 79
Safety instructions
Safety instructions
RE 92050/2023-06-15, Bosch Rexroth AG
80 A4VSO series 1x and 30 | Axial piston variable pump
Related documentation
Related documentation
Product-specific documentation
Document type Title Document number
Data sheet Axial piston variable pump A4VSO series 1X and 30 92053
for HFC hydraulic fluids
Axial piston units with DS2 secondary control 92057
A4VSO series 10 and 30
Axial piston units with DS3 secondary control 92059
A4VSO series 10 and 30
Control systems DR, DP, FR and DFR 92060
for axial piston variable pump A4VSO
A4VSO, A4VBO power controller LR2, LR3 and LR2N, LR3N 92064
Control systems MA and EMA... for 92072
axial piston variable pump A4VSO and A4VSG
Control systems 92076
HM, HS, HS5 and EO series 1x and 30
Control devices HD 92080
Electrohydraulic control system DFE1x for axial piston variable pumps 92088
A4VSO and A4VBO series 1x and 3x
Pressure and flow control system 30035
type SYHDFEE, SYHDFED, SYHDFEF
Universal through drive for axial piston variable pumps 95581
A10VSO, A10VO,A10VZO, A4VSO, A4VBO,
A15VSO/A15VLO and A15V(L)O
Storage and preservation of axial piston units 90312
Instruction manuals Axial piston variable pump A4VSO 92050-01-B
series 1, 2 and 3
Bosch Rexroth AG, RE 92050/2023-06-15