Epilamisation Agent for Metals and Plastics Product Specifications Product Technical Information: cohesive force adhesive force balance of Function the agent polymerizes on the solid causes total causes total cohesion and surface on evaporation of its solvent unwetting wetting adhesion
Film Thickness approx. 0.02 µm (E2/100)
Active Ingredient fluorinated polymer (solid) with a repelling effect on allknown lubricants Antispread reduces the surface tension of the solid as far as (reduced efficiency with fluorinated silicon oil can´t spread any more. Bearing material lubes) apparent slope caused by Solvent Partially fluorinated ether (FE 60); different surface (contains no chlorine, does not contain tensions perfluorinated carbons PFCs) Lubricant creeps to the Anti- untreated area. spread Thermal Stability -75 °C to +200 °C layer (film) [-103 °F to +392 °F] sliding Density 1.5 g/cm³ at 20 °C element Application Epilam layer is removed by Anti- spread temperature Color colorless friction. layer Boiling Range 30 °C to 60 °C [86 °F to 140 °F] lubricant remains Anti- within the sliding zone Ecology GWP = 350 (low global warming potential) spread ODP = 0 (no ozone depleting potential) layer ALT = 5 years (atmospheric life time) If possible sliding elements should be allowed to work without lubrication for a short time, thus the antispread Inflammability not inflammable layer being removed and the lubricant applicated remaining Bearing load Toxicology physiologically harmless, if used properly; precisely at the point or area of friction. details see safety data sheet Coverage approx. 85 g/m², depending on method of application and type of parts Directions: Cleaning surface contaminants, such as corrosion Compatibility with Plastics (static tests) inhibiting oils, detaching fluids and water compatible PE, PP, POM, PBT, PA66, PC*, PPOX*, must be removed before using Antispread. PMMA, ASA*, ABS*, elastomers (butyl- rubber, natural rubber, EPDM, EPR) Immersing 5-10 seconds at room temperature Sliding speed *additionally tension crack tests Spraying caution, use only in well ventilated limited compatible PTFE, silicone rubber (swelling during areas. longer exposure) Brushing should be done rapidly. Antispread is Efficacy on all materials, except PTFE highly volatile! Stamping a circular stamp can be used to build a barrier. Antispread Drying approx. 10 seconds at room temperature. Durability layer Warm air speeds the process.
zone of low fluorinated
lubricant (drop) Application: surface tension molecules The use of Antispread is recommended for precision and Antispread for lifetime lubrication in precision machinery. The use layer of Antispread ist essential for the silencing effect of high viscous lubricants in quartz clocks with step motors. The use Viscosity base of Antispread is imperative for the lubrication of plastics. material For dented wheels, bottom plates, electric contacts, printed circuit boards, ball bearings, sensitive machine tools, The Antispread coating acts as a network whose fluorine counters, printers, open bearings. Using the system „bristles“ repel the lubricant. bearing/shaft both parts, bearing as well as shaft must be treated with Antispread.
Test of Efficacy: Wetting
Apply drop of test fluid of 1 mm diameter ro treated parts.
Over 4-hour period, area covered by drop may not become bigger. Contact angle must be between 5° and 45° at room temperature. P247a Dr. Tillwich GmbH Werner Stehr Phone: +49 (0) 7451 5386-0 All information reflects our best knowledge. No responsibility is Certified Murber Steige 26 Telefax: +49 (0) 7451 5386-70 taken for printed data. Technical and chemical changes may occur acc. to D-72160 Horb (Ahldorf) info@tillwich-stehr.com without notice. We cannot be held liable for any use or application. ISO 9001