Professional Documents
Culture Documents
This user manual contains the most important information on operating this DUPS
safely. Each person concerned with the installation, commissioning, maintenance
and operation of V-Guard Solar Hybrid UPS must have read and understood the
entire user manual
IMPORTANT INSTALLATION INSTRUCTION
Do not connect the Output of UPS to main line output as this may damage the
UPS. Only connect required Fan, Light point, TV Point and 1-2 extra 6A socket for
your heavy load (Mixers/ Toasters/ Room cooler) within the specified rating of
product.
SALIENT FEATURES
• Monitoring and control of UPS by Android / iOS App.
• Facility to increase your fan speed by using mobile phone App.
• Additional equipment mode for critical equipment.
• Facility to increase Solar Hybrid UPS battery backup time by using
mobile phone App*.
• Facility to monitor load usage using App.
• Facility to save power by configuring Holiday mode using App while
going outstation.
• Digital Signal Controller based design for pure sine wave output.
• Equipped with inbuilt high efficiency solar charge controller with solar
panel compatibility as per specification.
• Selectable charging mode for different battery types (Flat, Tubular &
Local batteries) and capacities (80 to 230Ah).
• Battery Gravity Builder with overcharge and deep discharge protections.
• Provides emergency power to charge mobile phones through USB port
even when Digital Sinewave UPS has shut down due to low battery
protection.
V-GUARD SMART APP
Download V-Guard Smart App from Play Store or App Store. You can also
use this App for paper less warranty and complaint registration. For more
details about App go to User Assistance menu of My Product in the App.
• CONTROL DUPS FROM YOUR PHONE - The V-GUARD Smart DUPS easily
syncs with your smart phone through Wi-Fi or Bluetooth. Once your
product is registered on the V-Guard Smart app, you can control the DUPS
system through your mobile from anywhere.
1800
SMART PRO 1200 S
STATUS PAGE :
Ÿ Shows overall status of the product related battery,
solar, mains load performance etc.. of your DUPS
on the V-Guard Smart app.
Ÿ With the help of ON /OFF switch DUPS power ON /
OFF can be controlled.
SOLAR INFORMATION
SOLAR PAGE :
Ÿ Can give information about product installation
location.
Ÿ Real time solar generation can be checked.
Ÿ User can monitor solar savings details of Today,
Yesterday and Total based on solar utilization. User
can also calculates savings based on tariffs input
given in app.
Ÿ User can monitor 5 days weather forecast and plan
accordingly for power usage.
SMART SETTINGS PAGE :
1800
SMART PRO 1200 S Ÿ Forced power cut helps to get better output
performance when Mains voltage is low.
Ÿ Fast charging to Save time - Use Turbo Charge option
for faster charging of the batteries during emergency
situations.
Ÿ Appliance mode enables user to run high capacity
loads during mains failure for a defined duration.
Ÿ Reserve power helps to provide extra backup, even
after battery gets low.
Ÿ Save Energy Using Holiday Mode - When product is not
in use for long duration. Switch to holiday mode. It will
ensure saving of power and will also maintain your
batteries in healthy conditions.
Ÿ User can customize output voltage or backup time as
per their needs with the help of slider given.
1800
SMART PRO 1200 S
ç ALARM SETTINGS PAGE :
1800
SMART PRO 1200 S
User can set advance
battery low alarm, mains
change over buzzer and
overload level as per their
requirement.
è USAGE TRENDS :
Ÿ Provides graphical
representation of running
load on the DUPS.
Ÿ Provides power failure
history for last 7 days.
SWITCH SETTINGS :
1800
SMART PRO 1200 S
Ÿ Day time load usage mode is useful for working family where
nobody is available at home during day time. If you have selected
“No” and selected Power saver at Max mode, It will cut DUPS mains
in night to discharge battery to certain level for next day charging
through solar.
Amazon Alexa and Google Home connectivity helps you to control your
device using voice from anywhere as per convenience.
* All the readings and time shown in the App are calculated on STC and can be
affected by various operating conditions present at site. Value shown in App
should be taken as reference only, actual results may have variations as compared
to readings shown in the App.
CONFIGURATION PROCEDURE
In order to configure your mobile with Smart DUPS, press and hold the DUPS
ON/OFF switch continuously for 10 seconds (Approx) until 3rd beep sound occurs.
ON/OFF switch LED starts to blink. Now Press RECONFIGURE DUPS icon on APP
with in 15 minutes and configure DUPS as per the instructions given in the APP
# Equipment mode : Use this setting for running inverter technology based
Refrigerator through the DUPS.
**Time for a fresh 150Ah tubular battery at high charging mode selection and
mains voltage within 150 - 280V range.
*** subjected to material and usage conditions.
Due to continuous research, specifications are subjected to change without prior
notice.
Note : Electrical and electronic devices up to specified capacity can be powered by
this Solar Hybrid UPS.
UNDERSTANDING YOUR PRODUCT
I. UPS FRONT PANEL DESCRIPTIONS
A B C DE F G H
Fig 1
A. UPS MODE LED: UPS mode is set to run PC load. UPS mode LED glows when
the unit is in UPS mode, blinks if it is in Equipment mode and off if it is in
Normal mode. By default unit will be in Normal mode. In order to change the
mode from NORMAL to UPS or to Equipment mode, press the front panel
ON/OFF switch for 5 seconds continuously until second beep sound occurs
(Not applicable when water topping reminder indication active).
B. MAINS ON LED: Glows steady when the mains is available within the
normal limits (90-290V in NORMAL mode and 180-260V in UPS mode) and
blinks when mains out of range and off when mains not available (If Mains
voltage goes below the specified voltage range, i.e. Low cut condition - 2
blinks, If Mains voltage goes above the specified voltage range, i.e. High cut
condition - 3 blinks).
C. CHARGE LED: This will blinks when batteries are charging and Glows steady
when batteries are charged. For Tubular battery selection - 3 blinks, for Flat
Plate battery selection - 2 blinks & for Local battery selection - 1 blink).
D. BACKUP LED: This LED will glow steady when the UPS is in backup mode
due to mains failure or out of working range.
E. LOW BATT LED: Blinks during low battery warning and glows steady after
low battery shutdown with buzzer indication.
F. OVERLOAD LED: Blinks when the loading is above it’s specified capacity
and blinks with continuous buzzer after overload shutdown. Glows steady
after short circuit in output side. After 5 times of retrying overload protection
shutdown will happen. Again press ON/OFF switch to RESET/ turn ON the
product. It is advisable that connected loads in bypass should not be more
than the rated capacity of UPS.
G. SOLAR LED: Blinks when working in solar and glows steady if battery is fully
charged through solar. It stays off when solar is absent.
H. ON/OFF SWITCH: This switch can be used to make the unit ON/OFF and
this can be done by pressing the switch continuously for 1 second until a beep
sound occurs. BACKUP LED will be OFF when the unit is in OFF mode. If the
unit is in OFF mode, the load connected at the output will not work in the event
of mains failure, however charging will continue if mains is in normal limit. The
switch also works as a reset in an event of overload & low battery shutdown.
When the switch is in ON condition the switch glows and it will not glow if the
switch is OFF. This switch can be used for Normal, UPS and Equipment mode
selection. By default unit will be in normal mode. In order to change the mode
from Normal to UPS or from UPS to Equipment mode or from Equipment to
Normal mode press and hold the switch continuously for 5 seconds until
second beep occurs. UPS mode LED glows when the unit is in UPS mode,
blinks when it is in Equipment mode and off if it is in normal mode. Normal,
UPS and Equipment mode can be selected by using APP also. For this user has
to go switch settings portion in the APP where user can change the mode by
touching the mode selected option.
I . USB PORT : This is used to charge mobile phones even when Digital Sinewave
UPS has shut down due to low battery protection. Keep the USB port
covered when not in use to avoid accumulation of dust inside it.
LED Indications for some of the fault status of product is given below.
****UPS operation when mains RCB Trip : MAINS ON LED blinks and BACKUP
LED glows and there will be 5 times buzzer at 5 minutes interval during 20 minutes
of operation after that system goes off.
II. UPS BACK PANEL DESCRIPTIONS
3 45 7
1
2
6
SOLAR (25VOC)
9 8
Fig (2)
1. MAINS RCB: This is connected in line with the MAINS input to UPS. This will
trip to disconnect the mains to save the product in case of short circuit at load
side or excess overload in mains mode. It is recommended to connect rated
capacity load through UPS to avoid unnecessary RCB tripping.
2. OUTPUT SOCKET: This is provided for connecting the loads that will run
through the UPS while power is not available. It is recommended to use ISI
marked plug on this socket.
3. POWER SAVER MAX/NORMAL SWITCH : This system is equipped with
a selection switch (power saver) on back panel to utilize the available solar
power as per user requirement. On Max position system will cut the grid
power and connected load will run on available excess solar power. In
NORMAL position solar power will be used to charge the battery. Maximum
power saver position is recommended to installation having lesser power cut
or in winter. Normal power saver position is recommended to the installation
having longer power cuts. By keeping power saver switch in Max position
user can select Night mode using App. This mode allows user to discharge
the battery during night time there by utilize the unit saved through solar.
4. HC & NC SELECTION SWITCH: This can be used to select the charging
current of UPS. Keep the switch in HC when using 135-230Ah battery and in
NC when using 80-120Ah battery. It is recommended to keep the switch in
NC for local & flat plate batteries.
5. TUB/FP/LOCAL SELECTION SWITCH: This is battery selection mode. If
the battery used is tubular type, select TUB (Tubular) mode. If the battery
used is flat plate type, then select FP (Flat Plate)mode. If the battery used is
any Local make, select LOCAL mode for optimum performance. This setting
is very critical and needs to be done within 30 minutes of installation. After
that the setting cannot be done without disconnecting the battery. Wrong
setting can deteriorate the UPS backup and can even cause damage to
battery.
6. MAINS LEAD: This is used to connect input mains supply to the UPS. Ensure
earthing drop between Input ‘Neutral’ and ‘Earth’ below 1V to avoid electric
shock due to earth leakage.
7. POSITIVE BATTERY WIRE: Connect the positive battery wire (red) of UPS
to positive terminal of battery.
8. NEGATIVE BATTERY LEAD: Connect the negative battery wire (Black) of UPS
to negative terminal of Battery.
9. SOLAR + & SOLAR - : This is provided for connecting solar panel to UPS. The
panel should be with in the recommended capacity. During installation, the
polarity of panel should be correct. Connect the +ve terminal (Red wire) of panel
to SOLAR + and -ve terminal (Black wire) of panel to SOLAR - of the UPS.
25VOC,
640Wp Max
4. Switch on the front switch and check the output voltage in output socket. After
checking switch OFF the DUPS.
5. Only selected branches on D.B should be connected to DUPS output as shown in
fig 6, overloading on DUPS can cause damage to product.
Distribution
Neutral Strip
Distribution
Neutral Strip
Refrigerator
Refrigerator
Iron box
Iron box
Fig 6 Fig 7
Iron box
Iron box
Earth Strip
Distribution
Neutral Strip
N
L
Fig 8
8 Switch on the mains of DUPS and check the working of load branches got
connected through DUPS. After checking, check the charging LED on display it
should blink as per mode and battery type selection. Get the mode & battery type
selected as per need and battery type installed.
9. After doing all the settings switch OFF the mains and switch ON DUPS and check
the connected load they should be powered up in battery mode.
10. After checking all the loads reconnect the mains to complete the installation.
200-300W 4 Sq.mm
325 - 640W 6 Sq.mm
5. Mount the PV modules with recommended angle facing towards south.
Following are the recommended tilt angle for mounting solar panels to get
maximum energy harvest throughout the year in India.
Locations Recommended angle (Degree)
Kerala, Tamilnadu & Puducherry 10
Andhra Pradesh, Goa & Karnataka 15
Maharashtra 18
Odisha 21
Madhya Pradesh, Jharkhand, 24
Gujarat, West Bengal & Bihar
Rajasthan, Uttar Pradesh & Delhi 27
Haryana, Uttarakhand, Punjab & 30
Himachal Pradesh
6. Recommended solar panel connections which will provide maximum efficiency
as follows.
SOLAR + SOLAR
25V VOC, 500Wp
Option 1
Fig 10
25V VOC
125Wp } X 4 parallel
SOLAR + SOLAR
25V VOC, 640Wp
Option 2
25V VOC
160Wp } X 4 parallel
Fig 11
SOLAR + SOLAR
25V VOC, 550Wp
Option 3 Fig 12
25V VOC
110Wp } X 5 parallel
Note : It is recommended to keep minimum wiring length (not more than 30 feet)
between solar panel and UPS during installation.
Some possible load combinations for Smart Pro 1200 S is given below
POSSIBLE LOAD COMBINATIONS FOR SMART PRO 1200 S
LOAD***** A B C D
TV (LED/LCD) upto 55" 1 2 1
Tube Light 1 1 1
Fan 1 4 2
Room Cooler upto 300W /
1
Inverter Refrigerator upto 320 Litres
CFL/LED bulb upto 14W 3 8 4 2
Mixer upto 750W / Water Pump upto
1
0.75HP ******
Sl. No.\
QR Code
PRN-MN-014-04