Professional Documents
Culture Documents
0 1
This User’s Guide will walk you through the steps of how to operate your GE LOGIQ Book Cart. Step 1
Component list for part # 0014-03A. To adjust the height of the Cart, simply raise the Release Lever and pull up, or push down on the
Sono Tray.
01-LOGIQ Book 08-Cable Cover
02-Probe 09-Rubber Probe Holder NOTE: Be sure to place both hands on opposite sides of Tray when raising or lowering the Cart
03-Trunk Assembly 10-Large Gel Cup height as shown.
04-Chart Holder 11-Security Lock
05-CD-RW Drive 12-Optional Printer Shelf (Not Shown)
06-CD-RW Shelf 13-Optional VCR Shelf (Not Shown)
07-Power Strip (Not visible)
2
1
11
10 Step 2
To lock the Caster, press down with your foot on the Lock Tab.
9 To unlock the Caster, pull up with your foot on the Lock Tab.
NOTE: Locking Casters are on the back of the Cart.
8
7
Step 3
3
Place the LOGIQ Book on the Sono Tray making sure it
6
mounts behind the Stoppers.Rotate the LOGIQ Book Handle
so that it wraps under the Sono Tray.Plug in the AC Adapter
4
5
to the LOGIQ Book. Connect the AC Adapter and place AC
LOGIQ Book Box beneath the Sono Tray as shown.
Cart NOTE: Be sure to have all cables travel through the Cable Management Loop.
NOTE: You can use the provided velcro straps to wrap extra cable.
Step 4
Attach the Security Lock by first unlocking it with one of the provided keys.
Push the Positioning Lever up to minimize the hook height.
Slide the hook end of the lock into the Security Lock Slot of the LOGIQ
Book as shown.
Push the Positioning Lever down to maximize the hook inside the Security
Before Using
Lock Slot. Make sure the Positioning Lever Hole is aligned with the
Please read this User’s Guide carefully. It contains important advice concerning the use and safety Locking Pin andpush the Locking Pin to Lock.
of your GE LOGIQ Book Cart. Keep this User’s Guide in a safe place and pass it on to any NOTE: To make lever movement easier, rotate the cable up or down.
subsequent user. This cart must only be used for its intended purpose in accordance with this To unlock the Security Lock rotate key clockwise, the Locking Pin will retract toward the key side.
User’s Guide. Push the Positioning Lever up to minimize the hook height. Pull to remove the Security Lock from
the Lock Slot.
Please Pay Attention to the safeguards.
LOGIQ Book Cart Instructions Direction 2399122-100 Rev.0 2
Step 5 Optional Shelves
Place the CD-RW Drive onto the CD-RW shelf. Slide the hooks of the Shelf into the four designated slots
Connect the Serial Cord to the back of the CD-RW as shown. in the side of the Trunk Assembly. Lower the shelf into place.
Repeat for the AC Adapter. Screw in the Attachment Knob that came with your Shelf as
Route the Serial Cord and AC Adapter Cord through the shown.
side of the Trunk Assembly. To remove the Shelf, unscrew the Attachment Knob, then lift
up and pull out the Shelf.
Step 6 NOTE: These steps will be used on all Shelves and for the
Chart Holder.
Remove the Cable Cover by unscrewing the
NOTE: Shelves can attach to three locations on each side
Attachment knob on top of the Cable Cover,
of the Trunk Assembly.
then lifting up and pulling out on the Cable Cover.
Route any cables that come down from the LOGIQ
Book through the top hole. Optional Printers
Route the cables from any shelf equipment through
Attach the proper Printer Shelf to the either
the closest side holes to that shelf. (Ex: Step five)
side of the Trunk Assembly.
Route cables through the Trunk Assembly
as shown.
Black & White Printer - Small Printer Shelf
Color Printer - Large Printer Shelf