=e
What is Bitumode?
Produced by the Modern Waterproofing Company,
Bitumode is a line of polymer-modified bitumen
waterproofing membrane of the highest quality
Bitumode is modified by APP and APAO, thus
guaranteeing superior performance under various
conditions.
BITUMODE DELTA -P is reinforced with Spunbond
Non-woven Polyester (P) which provides high
mechanical properties
BITUMODE DELTA -P is a general purpose
membrane, can be applied virtually anywhere where
torch applied modified bitumen membranes subject
to light to moderate mechanical stresses are
specified, and normal low temperature performance
is required,
BITUMODE DELTA -P can be applied in
+ Single layer roofing system for normal use.
+ Double layer roofing system combined with
BITUMODE DELTA - G fiberglass reinforced
+ Waterproofing of toilets & wet area inside
buildings.
+ Slab on grade.
BITUMODE DELTA - P with Mineral Slated Finish
is recommended for exposed roofing system
(Unprotected) for Non-accessible roofs or roofs
‘subject to low traffic conditions.
Advantages
BITUMODE DELTA -P has been designed with
Special regard to provding clients with an excellent
and versatle product ine
Advantages of Bitumode DELTA — P include:
+ Easy to apply (by torch).
+ High mechanical properties
+ Absolute impermeabilty to water pressure.
+ Flexbilty at ow temperature up to -2c°
+ Excelent high temperature performance
+ Excelent adhesion on any surface
+ High dimensional stabi.
+ Environmentally friendly.
BITUMODE DELTA - P
APP MODIFIED BITUMEN PLASTOMERIC WATERPROOFING MEMBRANE
REINFORCED WITH SPUNBOND NON WOVEN POLYESTER
Quality Cor
‘The Modern Waterproofing Company is ISO 9001
certified. it applies a stringent quality control system
utilizing its in-house laboratory
Occasional samples are analyzed by independent
laboratories to ensure continued adherence to the
highest standards (ASTM, EN, etc.)
Each roll of Bitumode is individually coded with a
label containing all necessary information about the
roll, this is intended to ensure traceability in
accordance with ISO control standards.
Product Range
Standard thickness available includes 3mm and
‘4mm. Some types could be available by weight
3kgim? and 4kg/m?
Bottom surface finish is normally Polyethylene
Film (PE).
Upper surface finish choices include:
+ Polyethylene Film (PE)
+ Fine Sand (S)
+ Mineral Slated Grey (GY)
+ Mineral Slated Green (GRN)
+ Mineral Slated White (WT)
+ Mineral Stated Red (RD)
Slated rolls are available in 4kg, 4.5kg and 5kg per
square meter.
The nominal length of each roll is 10 meters and
the nominal width is one meter.
‘Special specification can be designed based on
client's needs.
‘This Publication cancels any previous one - Vor. § Printed May 2012BITUMODE DELTA - P
APP MODIFIED BITUMEN PLASTOMERIC WATERPROOFING MEMBRANE
REINFORCED WITH SPUNBOND NON WOVEN POLYESTER
TECHNICAL DATA TEST METHOD | _UNIT RESULT [ Eres]
Ralienah EN 1648-1 m 70 =
Rot With EN 1848-1 " 1 on
‘Thickness for PE finish EN 1849-1 mm 23.45 ees ra cl
Weight for slated surface finish EN 1849-1 kgim? 445.5 Pope lie oslo igh
Softening Pont Ring & Bal) astuD38 |e 2180 Reece
Be er soz RRS sa
Penetration at Be] _asmos | gam Bes ES aa.
Co Feb EN TT09 ‘e 010-2 Metntalep tae
Hoat Resistance EN 1110 * 120 Wat yatatny an
Reinforcement NonnovenPaystr
Tense srongh Tae | evi | NES 7
Elongation at break Vere [en izsr % Be
Res to t ie
WaiSseage? Winds | EN 120104 N i
TensietearResisance Weg | astwostar |S 32
“eit oni strength Wee | enieares | Neem oo ieee
Dimensional stably Hae | en ss07-1 Hy 303 we asta
Water absorption ASTM D-5147 0.15 max, TSE
Static puncture resistance EN 12730-2001 Kg 20 SST PRT Raglan
Dynamic puncture resistance EN 2691:2006 mm 4750 Reehigall PART eylae
Weer mosey at 100 Kpa [en 19262000 | - | Absoly impermeable [Exit ara
TnperbaBy to wae vapor EN 1831 i eae ania
‘Ageing due to U,V. radiation EN 1296, i Pass Rema ge DW palatal
Resstance to thermal ageing EN 1206 —_ | So sagge getraton cep ce
“aes we eonerae eae —| Wear 40 ST
Themal conduc STW c-t77 | Kean O12 Salon
Delete constant (E) ASTHLD-te0—[_—- 25 ei
Dielectric rigidity - Kyimm, 44 Al Gall adhe
‘verge Granut oss or Minar ; ara ee Snare
Slated Finis astm0497 | amin Lessthan 200 | SyShyetvatngercecs
ores
+ Above results are based on 4mm membrane.
+ Tolerance within 20% ofthe above results for mechanical characteristics complies withthe tolerance specication of (ASTM, EN).
+ Due to constant product improvements, MODERN company reserves the right to change above values without advance notice:
‘Storage:
‘ BITUMODE membranes should be stored vertically in well covered and ventilated place not subject to dict suntight
ILICATION INSTRUCTIONS:
* BITUMODE meméranes er insaled by propane torch welding method loos lai or fly bonded to the substrate depending on system
Faquirement
While unloading from truck the rolls shall by no means allowed to fal or be thrown down from the truck
‘To avoid applying the membrane to comers with 80 ° angle, sand cement cant stip Sx5 cm should be executed at horizontal - vertical
intersections
* Surface tobe waterproofed shouldbe clean ry, ee from dust and smooth, in case of regular surface a sand cement screed
recommended.
Before laying BITUMODE membranes, surface should be primed with cold applied bituminous primer (NIROL ~ S) or (NIROL - W)
Membrane is unrolled and placed in aligned postion, :
acl should ove ie nx! by 10emsGalaps and Som staggered en aps
nen, membrane shouldbe r-rled about hal of is length without changing fs orientation
* Using @ propane gas torch the membrane is un-roliad again slowly while applying the flame tothe entire exposed lower face (For fully
‘bonded system) -untl the plastic caver fim bums off and he bituminous mase stars meling, hus cresting a heet wold between the
Membrane and the substrate
« Then lorhing of he seas lakes place by heating ne contact ie a ie anc en laps by trch rom above, pressing he upper membrane
(0 fo the lower one using a trowel, the torch has fo be carefuly used avoiding fo keep the fame on the same point fr too long:
+ For sioping roofs start laying the membrane from the lower edge with longitudinal direction of ralls perpendicular to slope direction, side
lap of next roll to be placed above the rst one, ete
For detaled application res please refer to BITUMODE MANUAL GUIDE, where you can find construction tail raw
Modern Waterproofing Company MEMBER
2,1 Sobki St, Dahabi Sq, Neliopoie, Caro, Egypt NATIONAL
Tol: (e202) 248 410 03,
Fav: 0202) 290123 13, CONTRACTORS
ASSOGATION