Professional Documents
Culture Documents
MAX232 - TTL Convertor Datasheet
MAX232 - TTL Convertor Datasheet
MAX3222/MAX3232/MAX3237/MAX3241*
_______________General Description ____________________________Features
The MAX3222/MAX3232/MAX3237/MAX3241 trans- ♦ Low Supply Current:
ceivers have a proprietary low-dropout transmitter out- 300µA (MAX3222/MAX3232/MAX3241)
put stage enabling true RS-232 performance from a 500µA (MAX3237)
3.0V to 5.5V supply with a dual charge pump. The ♦ Guaranteed Data Rate:
devices require only four small 0.1µF external charge- 120kbps (MAX3222/MAX3232/MAX3241)
pump capacitors. The MAX3222, MAX3232, and 250kbps (MAX3237—Normal Operation)
MAX3241 are guaranteed to run at data rates of 1Mbps (MAX3237—MegaBaud Operation)
120kbps while maintaining RS-232 output levels. The
♦ 1µA Low-Power Shutdown with Receivers Active
MAX3237 is guaranteed to run at data rates of 250kbps (MAX3222/MAX3237/MAX3241)
in the normal operating mode and 1Mbps in the
MegaBaud™ operating mode, while maintaining RS-232 ♦ Flow-Through Pinout (MAX3237)
output levels. ♦ Meets EIA/TIA-232 Specifications Down to 3.0V
The MAX3222/MAX3232 have 2 receivers and 2 ♦ Guaranteed Mouse Driveability (MAX3241)
drivers. The MAX3222 features a 1µA shutdown mode ♦ Pin Compatible with Industry-Standard MAX232
that reduces power consumption and extends battery (MAX3232)
life in portable systems. Its receivers remain active in Pin Compatible with Industry-Standard MAX242
shutdown mode, allowing external devices such as (MAX3222)
modems to be monitored using only 1µA supply cur-
♦ Guaranteed Slew Rate:
rent. The MAX3222 and MAX3232 are pin, package,
6V/µs (MAX3222/MAX3232/MAX3237/MAX3241)
and functionally compatible with the industry-standard
24V/µs (MAX3237—MegaBaud Operation)
MAX242 and MAX232, respectively.
The MAX3241 is a complete serial port (3 drivers/
5 receivers) designed for notebook and subnotebook ______________Ordering Information
computers. The MAX3237 (5 drivers/3 receivers) is ideal PART TEMP. RANGE PIN-PACKAGE
for fast modem applications. Both these devices feature MAX3222CUP 0°C to +70°C 20 TSSOP
a shutdown mode in which all receivers can remain
MAX3222CAP 0°C to +70°C 20 SSOP
active while using only 1µA supply current. Receivers R1
(MAX3237/MAX3241) and R2 (MAX3241) have extra out- MAX3222CWN 0°C to +70°C 18 SO
puts in addition to their standard outputs. These extra MAX3222CPN 0°C to +70°C 18 Plastic DIP
outputs are always active, allowing external devices Ordering Information continued at end of data sheet.
such as a modem to be monitored without forward bias-
ing the protection diodes in circuitry that may have VCC
completely removed. _________________Pin Configurations
The MAX3222, MAX3237, and MAX3241 are available TOP VIEW
in space-saving TSSOP and SSOP packages. EN 1 18 SHDN
DIP/SO
Typical Operating Circuits appear at end of data sheet.
Pin Configurations continued at end of data sheet.
MegaBaud is a trademark of Maxim Integrated Products.
*Covered by U.S. Patent numbers 4,636,930; 4,679,134; 4,777,577; 4,797,899; 4,809,152; 4,897,774; 4,999,761; and other patents pending.
________________________________________________________________ Maxim Integrated Products 1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
3.0V to 5.5V, Low-Power, up to 1Mbps, True RS-232
Transceivers Using Four 0.1µF External Capacitors
ABSOLUTE MAXIMUM RATINGS
MAX3222/MAX3232/MAX3237/MAX3241
Note 1: V+ and V- can have a maximum magnitude of 7V, but their absolute difference cannot exceed 13V.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = +3.0V to +5.5V, C1–C4 = 0.1µF (Note 2), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER CONDITIONS MIN TYP MAX UNITS
DC CHARACTERISTICS
MAX3222/MAX3232/
No load, VCC = 3.3V or 5.0V, 0.3 1.0
VCC Power-Supply Current MAX3241 mA
TA = +25°C
MAX3237 0.5 2.0
Shutdown Supply Current SHDN = GND, TA = +25°C 1.0 10 µA
LOGIC INPUTS AND RECEIVER OUTPUTS
Input Logic Threshold Low
T_IN, EN, SHDN, MBAUD 0.8 V
(Note 3)
Input Logic Threshold High VCC = 3.3V 2.0
V
(Note 3) VCC = 5.0V 2.4
Input Leakage Current T_IN, EN, SHDN, MBAUD ±0.01 ±1.0 µA
Output Leakage Current Receivers disabled ±0.05 ±10 µA
Output Voltage Low IOUT = 1.6mA 0.4 V
Output Voltage High IOUT = -1.0mA VCC - 0.6 VCC - 0.1 V
RECEIVER INPUTS
Input Voltage Range -25 25 V
VCC = 3.3V 0.6 1.2
Input Threshold Low TA = +25°C V
VCC = 5.0V 0.8 1.5
VCC = 3.3V 1.5 2.4
Input Threshold High TA = +25°C V
VCC = 5.0V VCC = 5.0V 1.8 2.4
2 _______________________________________________________________________________________
3.0V to 5.5V, Low-Power, up to 1Mbps, True RS-232
Transceivers Using Four 0.1µF External Capacitors
ELECTRICAL CHARACTERISTICS (continued)
MAX3222/MAX3232/MAX3237/MAX3241
(VCC = +3.0V to +5.5V, C1–C4 = 0.1µF (Note 2), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
TIMING CHARACTERISTICS—MAX3222/MAX3232/MAX3241
(VCC = +3.0V to +5.5V, C1–C4 = 0.1µF (Note 2), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER CONDITIONS MIN TYP MAX UNITS
Maximum Data Rate RL = 3kΩ, CL = 1000pF, one transmitter switching 120 235 kbps
tPHL 0.3
Receiver Propagation Delay R_IN to R_OUT, CL = 150pF µs
tPLH 0.3
Receiver Output Enable Time Normal operation 200 ns
Receiver Output Disable Time Normal operation 200 ns
Transmitter Skew | tPHL - tPLH | 300 ns
Receiver Skew | tPHL - tPLH | 300 ns
CL = 150pF to
VCC = 3.3V, RL = 3Ω to 7kΩ, 6 30
1000pF
Transition-Region Slew Rate +3V to -3V or -3V to +3V, V/µs
TA = +25°C CL = 150pF to
4 30
2500pF
_______________________________________________________________________________________ 3
3.0V to 5.5V, Low-Power, up to 1Mbps, True RS-232
Transceivers Using Four 0.1µF External Capacitors
TIMING CHARACTERISTICS—MAX3237
MAX3222/MAX3232/MAX3237/MAX3241
(VCC = +3.0V to +5.5V, C1–C4 = 0.1µF (Note 2), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER CONDITIONS MIN TYP MAX UNITS
RL = 3kΩ, CL = 1000pF, one transmitter switching,
250
MBAUD = GND
VCC = 3.0V to 4.5V, RL = 3kΩ, CL = 250pF,
Maximum Data Rate 1000 kbps
one transmitter switching, MBAUD = VCC
VCC = 4.5V to 5.5V, RL = 3kΩ, CL = 1000pF,
1000
one transmitter switching, MBAUD = VCC
tPHL 0.15
Receiver Propagation Delay R_IN to R_OUT, CL = 150pF µs
tPLH 0.15
Receiver Output Enable Time Normal operation 200 ns
Receiver Output Disable Time Normal operation 200 ns
| tPHL - tPLH |, MBAUD = GND 100 ns
Transmitter Skew
| tPHL - tPLH |, MBAUD = VCC 25 ns
Receiver Skew | tPHL - tPLH | 50 ns
MBAUD =
6 30
CL = 150pF GND
VCC = 3.3V, RL = 3Ω to 7kΩ, to 1000pF MBAUD =
Transition-Region Slew Rate +3V to -3V or -3V to +3V, 24 150 V/µs
VCC
TA = +25°C
CL = 150pF to 2500pF,
4 30
MBAUD = GND
Note 2: MAX3222/MAX3232/MAX3241: C1–C4 = 0.1µF tested at 3.3V ±10%; C1 = 0.047µF, C2–C4 = 0.33µF tested at 5.0V ±10%.
MAX3237: C1–C4 = 0.1µF tested at 3.3V ±5%; C1–C4 = 0.22µF tested at 3.3V ±10%; C1 = 0.047µF, C2–C4 = 0.33µF tested
at 5.0V ±10%.
Note 3: Transmitter input hysteresis is typically 250mV.
MAX3222-03
MAX3222-02
20
35
4 18 235kbps
SUPPLY CURRENT (mA)
3 16 30
SLEW RATE (V/µs)
2
14 25
1 -SLEW
12 120kbps
0 20
10
-1 +SLEW
8 15
-2
20kbps
-3 6 10
-4 4
VOUT- 5
-5 2
-6 0 0
0 1000 2000 3000 4000 5000 150 1000 2000 3000 4000 5000 0 1000 2000 3000 4000 5000
LOAD CAPACITANCE (pF) LOAD CAPACITANCE (pF) LOAD CAPACITANCE (pF)
4 _______________________________________________________________________________________
3.0V to 5.5V, Low-Power, up to 1Mbps, True RS-232
Transceivers Using Four 0.1µF External Capacitors
_____________________________Typical Operating Characteristics (continued)
MAX3222/MAX3232/MAX3237/MAX3241
(VCC = +3.3V, 235kbps data rate, 0.1µF capacitors, all transmitters loaded with 3kΩ, TA = +25°C, unless otherwise noted.)
MAX3241 MAX3241 MAX3241
TRANSMITTER OUTPUT VOLTAGE SLEW RATE SUPPLY CURRENT vs. LOAD
vs. LOAD CAPACITANCE vs. LOAD CAPACITANCE CAPACITANCE WHEN TRANSMITTING DATA
7.5 24 45
MAX3222-04
MAX3222-06
MAX3222-05
VOUT+ 235kbps
TRANSMITTER OUTPUT VOLTAGE (V)
22 40
5.0
20 35
2.5 18 30
-SLEW 120kbps
1 TRANSMITTER AT 235kbps 16
2 TRANSMITTERS AT 30kbps 25
0 14
20
12 20kbps
-2.5 +SLEW 15
10
VOUT- 8 10
-5.0 ALL OUTPUTS LOADED WITH 3kΩ +CL
6 0.1µF CHARGE-PUMP CAPACITORS 5
FOR ALL DATA RATES UP TO 235kbps
-7.5 4 0
0 1000 2000 3000 4000 5000 0 1000 2000 3000 4000 5000 0 1000 2000 3000 4000 5000
LOAD CAPACITANCE (pF) LOAD CAPACITANCE (pF) LOAD CAPACITANCE (pF)
MAX3237 MAX3237 MAX3237
TRANSMITTER OUTPUT VOLTAGE TRANSMITTER OUTPUT VOLTAGE SLEW RATE vs. LOAD CAPACITANCE
vs. LOAD CAPACITANCE (MBAUD = GND) vs. LOAD CAPACITANCE (MBAUD = VCC) (MBAUD = GND)
7.5 7.5 12
MAX3222-09
MAX3222-07
MAX3222-08
1Mbps
TRANSMITTER OUTPUT VOLTAGE (V)
2.5 2.5 8
1 TRANSMITTER AT 240kbps 1 TRANSMITTER AT FULL DATA RATE
4 TRANSMITTERS AT 15kbps 4 TRANSMITTERS AT 1/16 DATA RATE
0 3kΩ + CL LOADS 0 3kΩ + CL LOAD, EACH OUTPUT 6
VCC = 3.3V VCC = 3.3V
-2.5 -2.5 4
1.5Mbps 1 TRANSMITTER AT 240kbps
2Mbps 4 TRANSMITTERS AT 15kbps
-5.0 -5.0 2
1Mbps 3kΩ + CL LOADS
VCC = 3.3V
-7.5 -7.5 0
0 1000 2000 3000 4000 5000 0 500 1000 1500 2000 0 1000 2000 3000 4000 5000
LOAD CAPACITANCE (pF) LOAD CAPACITANCE (pF) LOAD CAPACITANCE (pF)
MAX3237 MAX3237 MAX3237
SLEW RATE vs. LOAD CAPACITANCE SUPPLY CURRENT vs. SKEW vs. LOAD CAPACITANCE
(MBAUD = VCC) LOAD CAPACITANCE (MBAUD = GND) (tPLH - tPHL)
70 60 70
MAX3222-11
MAX3222-10
MAX3222-12
1 TRANSMITTER AT 512kbps
SKEW (ns)
60 60 4 TRANSMITTERS AT 32kbps
50 240kbps 3kΩ + CL LOADS
-SLEW, 1Mbps
SUPPLY CURRENT (mA)
_______________________________________________________________________________________ 5
3.0V to 5.5V, Low-Power, up to 1Mbps, True RS-232
Transceivers Using Four 0.1µF External Capacitors
______________________________________________________________Pin Description
MAX3222/MAX3232/MAX3237/MAX3241
PIN
5, 6, 7,
8, 15 8, 17 7, 14 9, 10, 11 T_OUT RS-232 Transmitter Outputs
10, 12
16 18 15 2 25 GND Ground
6 _______________________________________________________________________________________
3.0V to 5.5V, Low-Power, up to 1Mbps, True RS-232
Transceivers Using Four 0.1µF External Capacitors
_______________Detailed Description The MAX3222/MAX3237/MAX3241’s output stage is
MAX3222/MAX3232/MAX3237/MAX3241
turned off (high impedance) when the device is in shut-
Dual Charge-Pump Voltage Converter down mode. When the power is off, the MAX3222/
The MAX3222/MAX3232/MAX3237/MAX3241’s internal MAX3232/MAX3237/MAX3241 permit the outputs to be
power supply consists of a regulated dual charge pump driven up to ±12V.
that provides output voltages of +5.5V (doubling charge The transmitter inputs do not have pull-up resistors.
pump) and -5.5V (inverting charge pump), regardless of Connect unused inputs to GND or VCC.
the input voltage (VCC) over the 3.0V to 5.5V range. The
charge pumps operate in a discontinuous mode; if the MAX3237 MegaBaud Operation
output voltages are less than 5.5V, the charge pumps In normal operating mode (MBAUD = GND), the
are enabled, and if the output voltages exceed 5.5V, the MAX3237 transmitters guarantee a 250kbps data rate
charge pumps are disabled. Each charge pump with worst-case loads of 3kΩ in parallel with 1000pF.
requires a flying capacitor (C1, C2) and a reservoir This provides compatibility with PC-to-PC communica-
capacitor (C3, C4) to generate the V+ and V- supplies. tion software, such as Laplink™.
RS-232 Transmitters For higher speed serial communications, the MAX3237
The transmitters are inverting level translators that con- features MegaBaud operation. In MegaBaud operating
vert CMOS-logic levels to 5.0V EIA/TIA-232 levels. mode (MBAUD = VCC), the MAX3237 transmitters guar-
antee a 1Mbps data rate with worst-case loads of 3kΩ in
The MAX3222/MAX3232/MAX3241 transmitters guaran- parallel with 250pF for 3.0V < VCC < 4.5V. For 5V ±10%
tee a 120kbps data rate with worst-case loads of 3kΩ in operation, the MAX3237 transmitters guarantee a 1Mbps
parallel with 1000pF, providing compatibility with PC-to- data rate into worst-case loads of 3kΩ in parallel with
PC communication software (such as LapLink™). 1000pF.
Typically, these three devices can operate at data rates
of 235kbps. Transmitters can be paralleled to drive multi-
ple receivers or mice.
VCC VCC
0.1µF 0.1µF
R_ OUT R_ IN R_ OUT R_ IN
EN* EN*
0V 0V
5k 5k
* MAX3222/MAX3241 ONLY
MINIMUM SLEW-RATE TEST CIRCUIT MAXIMUM SLEW-RATE TEST CIRCUIT
_______________________________________________________________________________________ 7
3.0V to 5.5V, Low-Power, up to 1Mbps, True RS-232
Transceivers Using Four 0.1µF External Capacitors
RS-232 Receivers
MAX3222/MAX3232/MAX3237/MAX3241
8 _______________________________________________________________________________________
3.0V to 5.5V, Low-Power, up to 1Mbps, True RS-232
Transceivers Using Four 0.1µF External Capacitors
Table 1. MAX3222/MAX3237/MAX3241 Power-Supply Decoupling
MAX3222/MAX3232/MAX3237/MAX3241
Shutdown and Enable Control Truth Table In most circumstances, a 0.1µF bypass capacitor is
adequate. In applications that are sensitive to power-
R_OUTB supply noise, decouple VCC to ground with a capacitor
SHDN EN T_OUT R_OUT (MAX3237/ of the same value as charge-pump capacitor C1. Connect
MAX3241) bypass capacitors as close to the IC as possible.
0 0 High-Z Active Active Operation Down to 2.7V
0 1 High-Z High-Z Active Transmitter outputs will meet EIA/TIA-562 levels of
1 0 Active Active Active ±3.7V with supply voltages as low as 2.7V.
1 1 Active High-Z Active
Transmitter Outputs when
Exiting Shutdown
Figure 3 shows two transmitter outputs when exiting
shutdown mode. As they become active, the two trans-
Table 2. Required Minimum Capacitor Values mitter outputs are shown going to opposite RS-232 lev-
VCC C1 C2, C3, C4
els (one transmitter input is high, the other is low).
(V) (µF) (µF) Each transmitter is loaded with 3kΩ in parallel with
2500pF. The transmitter outputs display no ringing or
MAX3222/MAX3232/MAX3241 undesirable transients as they come out of shutdown.
3.0 to 3.6 0.1 0.1 Note that the transmitters are enabled only when the
magnitude of V- exceeds approximately 3V.
4.5 to 5.5 0.047 0.33
3.0 to 5.5 0.1 0.47 Mouse Driveability
The MAX3241 has been specifically designed to power
MAX3237
serial mice while operating from low-voltage power sup-
3.0 to 3.6 0.22 0.22 plies. It has been tested with leading mouse brands from
3.15 to 3.6 0.1 0.1 manufacturers such as Microsoft and Logitech. The
MAX3241 successfully drove all serial mice tested and
4.5 to 5.5 0.047 0.33
met their respective current and voltage requirements.
3.0 to 5.5 0.22 1.0 Figure 4a shows the transmitter output voltages under
increasing load current at 3.0V. Figure 4b shows a typical
mouse connection using the MAX3241.
5V/div
T2
2V/div
T1
50µs/div
VCC = 3.3V
C1–C4 = 0.1µF
_______________________________________________________________________________________ 9
3.0V to 5.5V, Low-Power, up to 1Mbps, True RS-232
Transceivers Using Four 0.1µF External Capacitors
MAX3222/MAX3232/MAX3237/MAX3241
MAX3222-04
5
Figure 4a. MAX3241 Transmitter Output Voltage vs. Load Current per Transmitter
VCC = 3V
to 5.5V
0.1µF
26
28 VCC 27
C1+ V+
C1 24 C3
C1- COMPUTER SERIAL PORT
1 C2+ 3
MAX3241 V-
C2 C4
2
C2-
14 T1IN T1OUT 9
+V
13 T2IN T2OUT 10
+V
12 T3IN T3OUT 11
VCC
R1OUTB -V
21
GND
20 R2OUTB
19 R1OUT R1IN 4 Tx
18 R2OUT 5k R2IN 5
17 R3OUT 5k R3IN 6
16 R4OUT 5k R4IN 7
MOUSE
5k
15 R5OUT R5IN 8
23 5k
EN
SHDN 22
GND
25
10 ______________________________________________________________________________________
3.0V to 5.5V, Low-Power, up to 1Mbps, True RS-232
Transceivers Using Four 0.1µF External Capacitors
MAX3222/MAX3232/MAX3237/MAX3241
VCC
T1IN 5V/div
0.1µF
C2+ MAX3222 V-
C2 MAX3232 C4
C2- MAX3237 5µs/div
MAX3241 VCC = 3.3V
T_ IN T_ OUT
Figure 6. MAX3241 Loopback Test Result at 120kbps
R_ OUT R_ IN
EN* 5k
0V 1000pF
T1IN 5V/div
VCC SHDN*
GND
T1OUT 5V/div
* MAX3222/MAX3241 ONLY
R1OUT 5V/div
______________________________________________________________________________________ 11
3.0V to 5.5V, Low-Power, up to 1Mbps, True RS-232
Transceivers Using Four 0.1µF External Capacitors
Interconnection with 3V and 5V Logic
MAX3222/MAX3232/MAX3237/MAX3241
+3.3V +3.3V
17 16
0.1µF 0.1µF
VCC VCC
2 C1+ 3 1 C1+ 2
V+ V+
C1 C3* C3*
0.1µF 4 0.1µF 3
C1- 0.1µF C1- 0.1µF
MAX3222 7
5 4 MAX3232 6
C2+ V- C2+ V-
C2 C4 C4
0.1µF 6 0.1µF 5
C2- 0.1µF C2- 0.1µF
1 EN 5k 5k
18
SHDN
GND GND
16
15
12 ______________________________________________________________________________________
3.0V to 5.5V, Low-Power, up to 1Mbps, True RS-232
Transceivers Using Four 0.1µF External Capacitors
_____________________________________Typical Operating Circuits (continued)
MAX3222/MAX3232/MAX3237/MAX3241
0.1µF
+3.3V
26 26
0.1µF 0.1µF
VCC VCC
28 C1+ 27 28 C1+ 27
V+ V+
0.1µF 0.1µF
25 24 C3*
C1- C1- 0.1µF
1 4 1 3
C2+ MAX3237 V- C2+ MAX3241 V-
0.1µF 0.1µF 0.1µF C4
3 2
C2- C2- 0.1µF
23 T2IN T2
T2OUT 6
TTL/CMOS 13 T2IN T2OUT 10 RS-232
INPUTS OUTPUTS
LOGIC 22 T3IN T3OUT 7 RS-232 12 T3IN T3OUT 11
T3 OUTPUTS
INPUTS
21 R1OUTB
19 T4IN T4OUT 10
T4
20 R2OUTB
17 T5IN T5OUT 12
T5
19 R1OUT R1IN 4
16 R1OUTB
5k
18 R2OUT R2IN 5
21 R1OUT R1 R1IN 8
5k
5k TTL/CMOS
OUTPUTS
17 R3OUT R3IN 6 RS-232
20 R2OUT R2IN 9 RS-232 INPUTS
LOGIC R2 INPUTS 5k
OUTPUTS
5k
16 R4OUT R4IN 7
18 R3OUT R3 R3IN 11
5k
5k
15 R5OUT R5IN 8
MBAUD 15 5k
13 EN
14 23 EN
SHDN 22
GND GND SHDN
2 25
* C3 CAN BE RETURNED TO EITHER VCC OR GROUND. * C3 CAN BE RETURNED TO EITHER VCC OR GROUND.
______________________________________________________________________________________ 13
3.0V to 5.5V, Low-Power, up to 1Mbps, True RS-232
Transceivers Using Four 0.1µF External Capacitors
_____________________________________________Pin Configurations (continued)
MAX3222/MAX3232/MAX3237/MAX3241
TOP VIEW
EN 1 20 SHDN
C1+ 2 19 VCC
C1+ 1 16 VCC
V+ 3 18 GND
V+ 2 15 GND
C1- 4 17 T1OUT
C1- 3 14 T1OUT
C2+ 5 MAX3222 16 R1IN
C2+ 4 MAX3232 13 R1IN
C2- 6 15 R1OUT
C2- 5 12 R1OUT
V- 7 14 N.C.
V- 6 11 T1IN
T2OUT 8 13 T1IN
T2OUT 7 10 T2IN
R2IN 9 12 T2IN
R2IN 8 9 R2OUT
R2OUT 10 11 N.C.
DIP/SO/TSSOP
SSOP/TSSOP
GND 2 27 V+ C2- 2 27 V+
C2- 3 26 VCC V- 3 26 VCC
V- 4 25 C1- R1IN 4 25 GND
T1OUT 5 24 T1IN R2IN 5 24 C1-
MAX3237 MAX3241
T2OUT 6 23 T2IN R3IN 6 23 EN
T3OUT 7 22 T3IN R4IN 7 22 SHDN
SSOP SO/SSOP/TSSOP
14 ______________________________________________________________________________________
3.0V to 5.5V, Low-Power, up to 1Mbps, True RS-232
Transceivers Using Four 0.1µF External Capacitors
Ordering Information (continued)
MAX3222/MAX3232/MAX3237/MAX3241
PART TEMP. RANGE PIN-PACKAGE PART TEMP. RANGE PIN-PACKAGE
MAX3222EUP -40°C to +85°C 20 TSSOP MAX3232EWE -40°C to +85°C 16 Wide SO
MAX3222EAP -40°C to +85°C 20 SSOP MAX3232EPE -40°C to +85°C 16 Plastic DIP
MAX3222EWN -40°C to +85°C 18 SO MAX3237CAI 0°C to +70°C 28 SSOP
MAX3222EPN -40°C to +85°C 18 Plastic DIP MAX3237EAI -40°C to +85°C 28 SSOP
MAX3222C/D 0°C to +70°C Dice* MAX3241CUI 0°C to +70°C 28 TSSOP
MAX3232CUE 0°C to +70°C 16 TSSOP MAX3241CAI 0°C to +70°C 28 SSOP
MAX3232CSE 0°C to +70°C 16 Narrow SO MAX3241CWI 0°C to +70°C 28 SO
MAX3232CWE 0°C to +70°C 16 Wide SO MAX3241EUI -40°C to +85°C 28 TSSOP
MAX3232CPE 0°C to +70°C 16 Plastic DIP MAX3241EAI -40°C to +85°C 28 SSOP
MAX3232EUE -40°C to +85°C 16 TSSOP MAX3241EWI -40°C to +85°C 28 SO
MAX3232ESE -40°C to +85°C 16 Narrow SO * Dice are tested at TA = +25°C, DC parameters only.
______________________________________________________________________________________ 15
3.0V to 5.5V, Low-Power, up to 1Mbps, True RS-232
Transceivers Using Four 0.1µF External Capacitors
___________________Chip Topography ___________________Chip Information
MAX3222/MAX3232/MAX3237/MAX3241
MAX3222
SHDN PART TRANSISTOR COUNT
V+ C1+ EN V CC
MAX3222 339
GND MAX3232 339
V-
R1OUT
0.087"
(2.209mm)
TSSOP.EPS
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
16 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 1999 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.