Professional Documents
Culture Documents
TM12864G Graphic Mode 128 X 64 LCD Datasheet
TM12864G Graphic Mode 128 X 64 LCD Datasheet
SPECIFICATION
FOR LCD MODULE
□ Preliminary specification
■ Final specification
VERIFIED BY
PREPARED BY CHECKED BY APPROVED BY
QA DEPT.
1. Description -----------------------------------------------------------------------------------------------3
2. Features ---------------------------------------------------------------------------------------------------3
4. Mechanical Characteristics--------------------------------------------------------------------------4
5. Circuit ------------------------------------------------------------------------------------------------------6
6. Interface description-----------------------------------------------------------------------------------8
8. Electrical Specifications-----------------------------------------------------------------------------12
11.Reliability------------------------------------------------------------------------------------------------- 17
2 Features
Item Contents
FSTN
LCD type
Positive
LCD Duty 1/64
LCD Bias 1/9
Polarizer Transflective
LCD background color White
Segment color Black
Backlighting LED
Backlighting type Edge
Backlighting color White
Backlighting drive 60mA
View direction 6:00 (wide view direction)
Operating temperature -20°C ~ +70°C
Storage temperature -30°C ~ +80°C
Controller ST7567
Frame --
Technology COG
Power supply VDD=3.0V
Data Transfer Serial
Notes:
Contrast ratio can slightly change with temperature and driving voltage.
LCD driving
VLCD -0.3 9.5 V
voltage
Operating
Top -20 +70 °C
temperature range No
Storage Condensation
Tst -30 +80 °C
temperature range
Note :
LCD operating voltage VLCD=V0–XV0
If the module is above these absolute maximum ratings. It may become permanently damaged.
4 Mechanical Characteristics
4.1 Mechanical features
Parameter Standard Value Unit
Display type Dot -matrix --
Note:
The maximum value of VDD should be less than 3.3 V to avoid permanent damage for LCD
module
Note: Please refer to IC: ST7567 data sheet for more details.
System bus timing for 4-line serial interface
Ratings Measuring
Parameter Symbol Unit Reference
Min Type Max. Temp.
Operating voltage Vo 8.5 8.7 8.9 V 25℃ 〔Note10-1〕
Frame frequency f 77 -- Hz -- 〔Note10-2〕
Cr(θ=20°,
Contrast ratio 3 -- -- -- 25 〔Note10-3〕
Ф=90° or 270°)
-- -- 250 25
Turn on ton ms
Response -- -- 0
〔Note10-4〕
time -- -- 200 25
Turn off toff ms
-- -- -- 0
θ1
Viewing Up-down -- -30~40 -- deg 25
(Ф=90° or 270°)
angle 〔Note10-5〕
θ2
(Cr≥2) Left-right -- -30~30 -- deg 25
(Ф=0° or 180°)
〔Note10-1〕The maximum and minimum ratings don’t mean the LCD works well in the whole range of Vo. Vo
must be adjusted to optimize the viewing angle and contrast. Refer to definition of drive voltage, refer to 10.2.
〔Note10-2〕The frequency shouldn’t be too low to avoid flicker. Refer to definition of drive voltage, refer to
10.2.
〔Note10-3〕Refer to 10.2/10.3/10.4/10.5.
〔Note10-4〕The selected state is dark and non-selected state is white( or bright) with positive type, reversely
the selected state is white (or bright) and non-selected state is dark with negative type. Refer to 10.6
definition of response time.
〔Note10-5〕Generally the viewing direction is 6:00 or12:00, sometimes 3:00 or 9:00. The range of left to right
and up to down based on Cr=2 show the viewing angle. Viewing angle range isn’t the range of defects
inspection. Refer to 10.4.
--30℃←→25℃←→80℃
30min 5min 30min
6 Temperature Cycle
after 10cycle, Restore 2H at 25℃
Power off
1.After testing,
cosmetic and electrical
defects should not
happen.
800mm, concrete floor,1corner,
9 Drop Test(package state) 2.the product should
3edges, 6 sides each time
remain at initial place
3. Product uncovered
or package broken is
not permitted.
Notes:
1. Each test item applies for a test sample only once, the test sample can not be used again in any other test
item.
2. The test sample is inspected after 2 hours or more storing at room temperature and room humidity after
each test item is finished.
3. The criteria refer to 11.2.
x<0.1mm 0.1mm≤x≤0.2mm
0.1mm≤A≤0.2mm
A<0.1mm
D<0.25mm
x<0.1mm 0.1mm≤x≤0.2mm
Max.3
x=(a+b)/2
defects
Max.1 defects allowed allowed
not counted
each segment
0.1mm≤a≤0.2mm
a<0.1mm
D>0
0.8W≤a≤1.2W Max.2
a=measured value of width defects
W=nominal value of width allowed
Judgment standard
Inspection items
Category(application: B zone)
c b a
b < Outer borderline of the seal
w b
c
Component soldering:
No cold soldering、short、open circuit、
burr、tin ball
The flat encapsulation component
PCB position deviation must be less than 1/3
18 Component
defect width of the pin (Pic.1); Soldering pad Lead
the sheet component deviation:
Pin deviates from the pad and contact
L1>0
with the near components is not
L2>0
permitted(Pic.2)
lead defect:
The lead lack must be less than 1/3 of its
width;
The lead burr must be less than 1/3 of
the seam;
Impurities connect with the near leads is
not permitted
socket
Base Board
13.4 Soldering
13.4.1 Use the high quality solders, only solder the I/O terminals.
13.4.2 No higher than 280℃ and time less than 3-4 second during soldering.
13.4.3 Rewiring: no more than 3 times.
13.4.4 when you remove connector or cable soldered to I/O terminals, please confirm that solder is fully
melted. If you remove by force, electrodes at I/O terminals may be damaged (or stripped off). It is
recommended to use solder suction machine.
TM 12864 G3 C C W G W A-1
1 2 3 4 5 6 7 8 9
NO. Explanation