Professional Documents
Culture Documents
CODE: 00ZBP30C25I1E
BP-30C25
BP-30C25Y
BP-30C25Z
MODEL BP-30C25T
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
11-13/16"
(30cm)
11-13/16" 17-23/32"
E. Direct rays of the sun, dust, temperature,
(30cm) (45cm)
humidity, gasses, chemicals, vibration
Temperature and humidity (Environmental conditions)
C. Power source (Capacity, voltage, frequency, This machine is designed to perform properly under the specified tem-
safety, plug) perature and humidity. If the temperature and humidity exceeds the
If the power specifications are not satisfied, the machine cannot exhibit specified range, the machine may not operate properly and or cause
full performances and may cause safety trouble. equipment failure.
Strictly observe the following specifications. Especially when the humidity is too high, paper absorbs humidity to
cause a paper jam or dirty copy.
Power capacity
Do not install the machine near a heater, a cooler, or a humidifier.
Check that the following power capacity is satisfied. If not, additionally
provide a power source.
Current capacity
Japan: 20A or more
EX 100V: 20A or more
EX 200V: 10A or more
Check the shape of the power plug of the machine, and insert it into a Condensation may form inside the machine causing multiple troubles.
power outlet of the acceptable shape. Use enough care for ventilation.
Power voltage
Measure the voltage during copying to check that the voltage is in the
range of the specified voltage 10%.
If the voltage is outside the specified range, please have a certified
electrician upgrade the outlet.
(An electrical work is required.)
Use of a step-up transformer is also available. In this case, the capac-
ity must be great enough for the max. power consumption of the
machine.
20%
Operational environment
Temperature: 10 to 35C
Humidity: 20 to 85% RH
Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m)
Contaminates
If dust enters the machine, it may cause dirty copy and a paper jam,
resulting in a shortened lifetime.
• When and after removing the parts from an anti-static bag (case),
use an earth band as shown below:
• Put an earth band to your arm, and connect it to the machine.
Direct sunlight
If the machine is installed under the rays of the sun, the exterior of the
machine may be discolored and abnormal copies may be produced.
Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
B. Delivery
Remove the packing materials prior to installation in the office environ-
ment.
1. System diagram
BP-30C25/BP-30C25Y/BP-30C25Z/BP-30C25T
DIGITAL FULL COLOR
MULTIFUNCTIONAL SYSTEM
BP-30C25 CONFIGURATION 1 – 1
2. Product List
<Main Unit>
*1: Option for N.A., Europe (included Russia), Oceania, Hong Kong, Singapore, Malaysia, Thailand, South Africa, Philippines, India, Vietnam, UAE
and China. For the other areas, optional setting will be considered after acquisition of the Safety Standard.
*2: Varies depending on area.
3. Option List
Description Model name Name
500-Sheet Paper Feed Tray BP-CS10 500-SHEET PAPER FEED TRAY OPT
Stand/2x500 Sheet Paper Drawer *4 BP-DE10 STAND/2x500 SHEET PAPER DRAWER OPT
High Stand BP-DS10 HIGH STAND OPT
Low Stand BP-DS11 LOW STAND OPT
PS Expansion Kit MX-PK13 PS3 EXPANSION KIT OPT
Barcode Font Kit MX-PF10 BARCODE FONT KIT OPT
Direct Print Expansion Kit MX-PU10 DIRECT PRINT EXPANSION KIT OPT
Soft high compression PDF expansion kit MX-EB19 ENHANCED COMPRESSION KIT OPT
OCR EXPANSION KIT MX-EB20 OCR EXPANSION KIT OPT
Fax Expansion Kit MX-FX15 FACSIMILE EXPANSION KIT OPT*2
Internet Fax Expansion Kit MX-FWX1 INTERNET FAX EXPANSION KIT OPT
Data Security Kit BP-FR10U DATA SECURITY KIT OPT
Sharpdesk 1 License Kit MX-USX1 SHARPDESK 1 LICENSE KIT OPT
Sharpdesk 5 License Kit MX-USX5 SHARPDESK 5 LICENSE KIT OPT*3
Sharpdesk 10 License Kit MX-US10 SHARPDESK 10 LICENSE KIT OPT
Sharpdesk 50 License Kit MX-US50 SHARPDESK 50 LICENSE KIT OPT
Sharpdesk 100 License Kit MX-USA0 SHARPDESK 100 LICENSE KIT OPT
Application Integration Module MX-AMX1 APPLICATION INTEGRATION MODULE OPT
Application Communication Module MX-AMX2 APPLICATION COMMUNICATION MODULE OPT
External Account Module MX-AMX3 EXTERNAL ACCOUNT MODULE OPT
Wireless LAN Module MX-EB18 WIRELESS LAN ADAPTOR OPT*1
BP-30C25 CONFIGURATION 1 – 2
[2] BP-30C25/BP-30C25Y/BP-30C25Z/BP-30C25T
BP-30C25
(MAIN UNIT)
Service Manual
Installation flowchart
Cut the polypropylene bands. Shake the toner cartridge horizontally OPC drum phase adjustment SIM
several times. (Automatic adjustment) 50-22
Cut the tape on the upper side in the
order shown. Open the front cover and insert each Color registration adjustment
toner cartridge. (Automatic adjustment)
Remove the packing material.
Copy color balance and
Open the Plastic bag. density check.
Lift the main unit slowly by 2 peoples. Printer color balance/density SIM
B. Cleaning check 64-5
Put it gently to the flat and safety place. Cleaning of LSU's dust-proof glass. When there are defects in a picture by
the contents mentioned above, you carry
out the following contents, and confirm a
picture.
D. Lock release
A. Unpacking
1) Cut the polypropylene bands. ĭ Ĭ
Ĭ ĭ
4) Lift the main unit slowly by 2 peoples, and put it gently to the flat
and safety place.
Accessory unit
AC cable AC cable
(inlet type) (direct installation type)
ĭ
Ĭ
Ĭ
Ĭ
• When pulling out the DV/Process unit, hold it with the lock lever.
• Do not pull on the DV/Process unit by holding the DV unit's har-
ness.
DV shutter cover
Remove the tape slowly in the direction 13) Close the position lock unit.
of the arrow so that DV shutter cover
does not come off.
D. Lock release
(1) Tray rotation plate lock release This models have been shipped with developer enclosed into the
developer unit and done Sim25-2. Therefore do NOT execute Sim25-2
1) Pull out the tray. Turn the fixing material and remove it. Remove
at machine installation.
the caution label.
If executed Sim25-2, replace all of the developers with new ones and
Close the tray which was pulled out.
execute Sim25-2. If the machine have been used without replacing the
new developer. It may be trouble related to the life performance.
B. Cleaning
(1) Cleaning of LSU's dust-proof glass
Dust from the transfer belt or shutter or some other adjacent part may
fall onto the LSU during transport or installation.
Be sure to clean the dust-proof glass before checking the image qual-
ity.
1) Remove the waste toner box.
4) Attach the waste toner box.
Both ends being locked surely.
ĭ
Ĭ
Ĭ
ĭ
D. Specifications setup
Use simulation 26-6 to set the machines destination.
SIM No Content
26 6 Used to set the destination.
SIM No Content
26 3 Used to set the auditor specification mode.
5 Used to set the count mode of the total counter and
the maintenance counter.
18 Used to set YES/NO of the toner save mode (Only in
UK and Japan versions)
* For other destination versions, this setup is made
by the user program.
52 Used to set YES/NO of counting when non-print
paper is passed through each counter.
For the color (gray) balance, use the servicing color test chart (UKOG-
0326FCZZ/UKOG-0326FC11) to check.
(Color copy)
Patch 1 is SHARP gray chart
slightly copied.
SHARP GRAY CHART
1 2 3 4 5 6 7 8 9 10 W
Patch 2 is copied.
(Black-and-white copy)
Patch 2 is SHARP gray chart
slightly copied.
SHARP GRAY CHART
1 2 3 4 5 6 7 8 9 10 W
Patch 3 is copied.
(Color copy)
Low High
density density
Y
Bk
A B C D E F G H I J K L M N O P Q
The print density must be changed gradually from the lighter level to
the darker level. The density changing direction must not be reversed.
1) The max. density section is not blurred.
The density level of each color must be almost at the same level.
2) Patch C or D of each of Y, M, C, and BK is very slightly copied.
(4) Copy/Printer color balance and density adjustment
(Automatic adjustment) 3) Patch for each of Y, M, C, BK
The patch density is identical between patches or not reversed.
The patch density is changed gradually.
When a printer option is installed, be sure to execute the above item. 5) Press [EXECUTE] key.
The printer color patch image (adjustment pattern) is printed out.
1) Enter the SIM46-74 mode. (A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.)
2) Press [EXECUTE] key. 6) Set the color patch image (adjustment pattern) printed in the pro-
The high density process control is performed, and the copy color cedure 5) on the document table.
patch image (adjustment pattern) is printed out. Set the color patch image (adjustment pattern) printed in the pro-
(A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.) cedure 2) on the document table. Place the color patch image so
3) Set the color patch image (adjustment pattern) paper printed in that the fine lines are on the left side. At that time, place 5 sheets
procedure 2) on the document table. of white paper on the printed color patch image (adjustment pat-
Set the color patch image (adjustment pattern) printed in the pro- tern).
cedure 2) on the document table. Place the color patch image so
that the fine lines are on the left side. At that time, place 5 sheets
of white paper on the printed color patch image (adjustment pat-
tern). PRINTER CALIBRATION
$M
# $ % & ' ( ) * + , - . / 0 1 2 3 240±1.2mm
8) The initial setting menu of the half-tone image correction is dis- Perform the step below if the result is not satisfactory:
played. Press [OK] key. 6) Change setting item 1: BK-MAG.
The initial setting of the half-tone image correction is performed. The length will change by 0.1 mm by changing the value by one.
9) Wait until [EXECUTE] key is displayed. When it is displayed, Increase the value to increase the magnification toward main
press it. scanning direction for BK image. Decrease the value to decrease
The half-tone image correction is performed. the magnification.
10) When "COMPLETED THIS PROCEDURE" is displayed, the Repeat the steps 2) to 6) until satisfactory result is obtained.
adjustment operation is completed. b. Print image position adjustment (Main scanning direction, sub
Cancel SIM46-74. scanning direction)
The adjustment result becomes valid only when the both adjust- Make sure that following item is in proper condition prior to the adjust-
ments in the copy mode and in the printer mode are completed. ment:
For example, if the copy color balance adjustment (automatic • ADJ 4-A Print image magnification adjustment (Main scanning direc-
adjustment) is performed and the simulation is canceled, the tion)
adjustment result is invalid.
1) Enter Simulation 50-10 mode.
2) Load A4 (11x8.5) or A3 (11x17) paper into a paper tray.
11) Check the copy color balance and density.
3) Press [Start] key
(Refer to the item of the copy color balance and density check.)
Check pattern will be printed.
12) Check the printer color balance and density.
(Refer to the item of the printer color balance and density check.)
If the color balance or density is not in the satisfactory level even after
execution of the automatic and manual adjustments, there may be
another cause.
Troubleshoot the cause, repair or perform necessary works, and
repeat the adjustment from the beginning.
If color balance or density is not satisfied, adjust the copy and printer
color balance by SIM 46-74.
Z1 Z1+Z2 total:4.0mm±2.0mm
X Y
4.0±1.0mm 2.0∼5.0mm
Z2 Z1+Z2 total:4.0mm±2.0mm
The setting items “2: MAIN-STD” and “3: SUB-STD” are to change
all print positions.
Execute them if adjustment of all trays is necessary after replace-
ment of LSU etc.
BP-CS10
1 2 3
4 5 6
BP-30C25 BP-CS10 (500-SHEET PAPER FEED TRAY), BP-DE10 (STAND/2x500 SHEET PAPER DRAWER) 3 – 1
C. Removal of the fixing tape and protection 2) Remove the stand/2x500 sheet paper drawer from the polyethyl-
material ene bag, and remove the fixing tape and the protection material.
1) Remove the 500 sheet paper feed tray from the polyethylene bag,
and remove the fixing tape and the protection material.
x2
Since Rear cabinet has not been screwed, remove the tape and
keep the Rear cabinet out of reach.
Since Rear cabinet has not been screwed, remove the tape and
keep the Rear cabinet out of reach.
3 nails
3 nails
BP-30C25 BP-CS10 (500-SHEET PAPER FEED TRAY), BP-DE10 (STAND/2x500 SHEET PAPER DRAWER) 3 – 2
2. Installation (1) Main unit and the 500 sheet paper feed tray (BP-
CS10) connection
1) Remove the cover on the left rear.
ĭ
Ĭ
Gently place main unit onto the optional Cassette, aligning and insert-
ing the 3 locating bosses of optional tray into the locating holes on the
bottom of the main unit.
3) Place the main unit in BP-CS10.
Pay attention to the position of the boss which is the connection
part of BP-CS10.
* BP-DE10 can not be attached to the main unit.
BP-30C25 BP-CS10 (500-SHEET PAPER FEED TRAY), BP-DE10 (STAND/2x500 SHEET PAPER DRAWER) 3 – 3
Lower the main body straight. 6) Align the left and right connecting plates with the screw holes on
the body and fasten them with screws.
2 nails
ĭ
Ĭ
Ĭ
ĭ
Ĭ
ĭ
BP-30C25 BP-CS10 (500-SHEET PAPER FEED TRAY), BP-DE10 (STAND/2x500 SHEET PAPER DRAWER) 3 – 4
9) Slide the lever on the right rearward in the upward direction and (2) Harness connection to the main unit
hook it on the main frame and fasten it with screws. 1) Remove the screw and slide the rear cabinet lower upward to
remove it.
2) Bend the rib of the rear cabinet lower and remove it.
11) Attach the size display sheet to the tray and return the tray to the
BP-CS10. 3) Attach the saddle to the main frame.
BP-30C25 BP-CS10 (500-SHEET PAPER FEED TRAY), BP-DE10 (STAND/2x500 SHEET PAPER DRAWER) 3 – 5
4) Put the snap band in the hole. (4) Stand/2x500 sheet paper drawer (BP-DE10) and 500
Pass the harness through the edge saddle and the saddle. sheet paper feed tray (BP-CS10) connection
Connect the connector to the relay connector.
į
Į
Ĭ
This reuse band is not inserted. 2) Attach the edge saddle included in BP-DE10 to BP-CS10.
BP-CS10
BP-DE10
BP-30C25 BP-CS10 (500-SHEET PAPER FEED TRAY), BP-DE10 (STAND/2x500 SHEET PAPER DRAWER) 3 – 6
4) Remove BP-CS tray and BP-DE10 upper tray. 7) Fix the connection plate attached to BP-DE10 to the screw hole of
BP-CS10 and fix it with screws.
5) Align the connecting plate on the left side and the right side with
the screw hole and screw it.
BP-30C25 BP-CS10 (500-SHEET PAPER FEED TRAY), BP-DE10 (STAND/2x500 SHEET PAPER DRAWER) 3 – 7
10) Connect the harness connector from BP-DE10 to the BP-CS10
PWB.
BP-30C25 BP-CS10 (500-SHEET PAPER FEED TRAY), BP-DE10 (STAND/2x500 SHEET PAPER DRAWER) 3 – 8
[4] BP-DS10/DS11 (HIGH STAND/LOW STAND)
BP-30C25
Service Manual
1. Unpacking 2. Installation
Unpack the package, and check to confirm that all the parts are pro- 1) Remove the left rear cover of BP-CS10
vided.
BP-DS10
(HIGH STAND) Bundled screws
Connect to BP-DS10
Quantity
No. Name
BP-DS10 BP-DS11
1 Fixing screw (S-tight M4×8) 4 4
BP-DS10
BP-DS11
1. Parts list
Kit name Kit part code No. Parts name Parts code Q'ty
Heater kit DKIT-0024QSZZ 1 WH PWB CPWBF0376QS51 1
(200V series) 2 TH PWB CPWBF0367QSE1 1
3 Saddle LHLDW2373FCPZ 2
4 Saddle LHLDW2374FCPZ 1
5 Heater mounting plate LPLTM1089QSZZ 1
6 WH PWB mounting plate LPLTM1160QSZZ 1
7 Screw (M3x8 P) LX-BZ1123FCPZ 1
8 TH2 harness QCNW-0189QSPZ 1
9 WH harness QCNW-0202QSPZ 1
10 WH-CSS harness QCNW-0237QSPZ 1
11 WH switch QSW-C9294QCZZ 1
12 Heater (200V series) RHETP0167FCP1 1
13 WH switch label TLABZ5256FCZZ 1
14 High temperature caution label TLABZ5466FCZ1 1
15 Screw (M3x6 S-tight) XHBS730P06000 3
16 Screw (M3x8 S-tight) XHBS730P08000 2
17 POWER SW LABEL CCB TLABH1186QSZZ 1
1 2 3 4 5
6 7 8 9 10
DH POWER
11 12 13 14 15 16
17
1 2 3 4
5 6 7 8
Kit name Kit part code No. Parts name Parts code Q'ty
STAND/2x500 SHEET PAPER DKIT-0028QSZZ 1 3CS WH harness QCNW-0241QSPZ 1
DRAWER heater kit (200V series) 2 Saddle LHLDW2373FCPZ 1
3 Heater mounting plate LPLTM1162QSZZ 2
4 Heater cover LPLTM1163QSZZ 2
5 Heater (200V series) RHETP0167FCP1 2
6 High temperature caution label TLABZ5466FCZ1 2
7 Screw (M3x4 S-tight) XHBS730P04000 6
8 Screw (M4x6 S-tight) XHBS740P06000 2
1 2 3 4
5 6 7 8
Before installation, be sure to turn both the operation and main power
switches off and disconnect the power plug from the power outlet.
Make double sure that the data lamp on the operation panel does not
light up or blink when performing installation.
3) When not using the dehumidifier heater after checking, turn off the
dehumidifier heater switch.
(16)
(6)
(1)
(16)
(f)
*2
Connect the WH harness to the dehumidifier heater control
switch.(Connect to the terminal on the AC cord side.) And attach
the dehumidifier heater control switch.
(15)
(a)
(15)
(11)
(b) (c)
(a)
(3) TH PWB attachment
1) Remove the 1casette.
Attach the High temperature caution label to the tray.
(9)
(g)
(f)
(d)
(e)
(c) ĭ
Ĭ
(3) (b)
*2
(14)
(3)
(g)
*1
2 nails
(8)
LSU
ĭ (7)
Į
OK direction
(12)
NG direction (15)
(5)
(4)
(10)
Put in a groove.
DH POWER
4) Take the harness out of the hole.
Connect the connectors.
(13)
(17)
Connect
connector.
NG direction
(7)
Connect.
(7)
(5)
2) Attach the mini clamp on the heater mounting plate upper and
pass the heater harness through it.
(2)
(6)
(4)
(a)
(1)
(b)
(c)
(d)
(e)
(f)
*1
Pass the 2CS WH harness
through the saddle and
edge saddle.
(b)
(e)
(d)
(f)
(c)
*1
(a)
(8)
NG direction
(7)
(7)
(5)
(3)
2) Attach the mini clamp on the heater mounting plate upper and
pass the heater harness through it.
(2)
3) Attach the heater cover (packing part No. 4) to the heater mount-
ing plate (packing part No. 3), and secure it with the screw (M3x4
S-tight) (packing part No.7).
(8)
(4)
(7)
(a)
(e)
(d)
(6)
(b)
(f)
(3) Heater harness attachment
1) Connect the 3CS WH harness to the 2CS WH harness.
Pass the 3CS WH harness through edge saddle. (g)
Connect the 3CS WH harness to the heater harness of the tray3.
Attach the reusable band of the 3CS WH harness.
(c)
Pass the 3CS WH harness through edge saddle.
Connect the 3CS WH harness to the heater harness of the tray4.
Attach the reusable band of the 3CS WH harness.
Note:Passing the WH harness in the back
(a)
(1)
(b)
(d) (e)
(f)
(g)
(c)
1 2 3 4 5
6*
U.K
Germany
France
* This is not bundled with the machines whose destinations are not
above mentioned destinations.
2. Installation
Before installation, be sure to turn both the operation and main power No.3 Step screw
switches off and disconnect the power plug from the power outlet.
Make double sure that the data lamp on the operation panel does not
light up or blink when performing installation.
Reuse
F. Destination setting
1) Execute SIM26-6.
2) Check to confirm that the destination setting of the machine
matches the specifications of the FAX destination. If not, the FAX
may not function properly.
Flow chart
Check to confirm that it is securely connected.
No Trouble F6-21
No Trouble F6-21
No.4
Screw M3-10 G. Clear the FAX related software switches
CN44
(SIM66-2.)
D. Cover attachment
1) Attach the cover with the screw.
No Trouble F6-21
No Trouble
SIM24-1
When connecting the line cable (to LINE or TEL), wind the line cable
one turn around the included ferrite core as shown in the figure, and
connect to the modular jack which is marked with “LINE.”
1 turn
About 10 cm
1. Preparation
A. Supported IC card readers
1 2 3 4
B. Necessary parts
Prepare the following service parts in advance.
1 2
Bundle excess cables.
No. Parts code Parts name Q’ty
4) Connect the USB cable to the main unit.
1 LHLDWA175WJUZ Clump 3
2 QCNWN3671BHPZ USB cable 1
2. Installation
Before installation, be sure to turn both the operation and main power
switches off and disconnect the power plug from the power outlet.
Make double sure that the data lamp on the operation panel does not
light up or blink when performing installation.
1) Connect the USB cable to the IC card reader.
[General]
Read Success.
Key name Description
Card ID : XXXXX Version Setting file version (* Fixed to 1.0)
Facility Code : XXXXX Card Set as shown below depending on the kind of the card to be set.
*1
1 2 3
* Products prior to June 2017 (without the “N” mark on the outer box)
When installing, the new USB connector PWB needs to be replaced.
2. Installation
NOTE: Before installation, be sure to operation panel switch off and
then main power switch off and disconnect the power plug
from the power outlet. And, disconnect the LAN cable and do
not connect the USB adapter after installing the wireless LAN.
Packing case
Perform the appropriate action for the customer not to connect
the LAN cable.
2 nails
2 nails
Ĭ ĭ
DUNT-9009DS13 COM1
No. Name Quantity
1 RS232C PWB unit 1
2 Screw 2
2. Installation
4) Cut the cover in a nipper.
A. Installation of RS232C PWB unit
1) Remove the screw and the cover.
Print the various setup data and the adjustment data (list) with SIM22-
6 and keep the data.
• In case of a memory trouble, if the data are not kept, all the adjust-
ments must be made again.
• If the data are kept, the setup values and the adjustment values can
be entered without adjustments, shortening the servicing time.
Example:
Trademark acknowledgements
x Microsoft®, Windows®, Windows® 8, Windows® 8.1, Windows® 10,
Windows® Server 2012, Windows® Server 2012 R2, Windows® Server 2016,
Windows® Server 2019, Internet Explorer®, and Microsoft Edge®
are registered trademarks or trademarks of Microsoft Corporation in the U.S.A.
and other countries.
x PostScript is a registered trademark of Adobe Systems Incorporated.
x Macintosh, Mac OS, AppleTalk, EtherTalk, Laser Writer, and Safari are registered
trademarks or trademarks of Apple Inc.
x IBM, PC/AT, and Power PC are trademarks of International Business Machines
Corporation.
x Acrobat® Reader Copyright® Adobe Systems Incorporated. All rights reserved.
Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe
Systems Incorporated.
x PCL is a registered trademark of the Hewlett-Packard Company.
x Sharpdesk is a trademark of Sharp Corporation.
x All other trademarks and copyrights are the property of their respective owners.
SHARP CORPORATION
Business Solutions BU