Professional Documents
Culture Documents
2xNC/2xNO
PKEY07
Table of Contents
Overview
Hardware Specifications
Signal Descriptions
Functional Specifications
Wiring Diagrams
Installation
Contact Information
Ordering information
Overview
The SCANBELT Intelligent Pullkey forms part of a conveyor protection system. When
correctly installed, these devices provide personnel with an emergency latching tripping
mechanism that is accessible on either side of the conveyor belt. The tripping mechanism
spans the entire length of the conveyor belt, providing a continuous tripping mechanism.
This is achieved by the installation of pull switches on both sides of the conveyor belt at
100m intervals. Each pull switch is interlinked via a pull-cable on the one side of the
conveyor belt. Pull switches mounted on the opposite side of the conveyor belt are
interlinked via steel wire rope.
Each trip switch also sounds an audible alarm via two piezo-resistive buzzers, warning
operators and personnel working in the vicinity of the conveyor belt of an impending
conveyor belt start up.
In the event of a trip at any pull switch, the device transmits its address to the controller
at the head end.
Rugged Construction
U.V Stabilized
Unique ABS and Polycarbonate blend
2 Normally Open and 2 Normally Closed Contacts
Audio and Visual Trip Indication
Dual integrated Pre-Start Siren
Designed for operation in harsh environments such as Power Stations
Simple Installation
Integrated lightening and surge protection
Simple Hook up – only 2 holes required
Up to 99 Units can be installed per system
Can be installed on conveyor systems with length of up to 9.9Km with
suitable power supplies
Hardware Specifications
Description Specification
Power
Supply Voltage 24VDC
Supply Current –Max 35mA
Mechanical
Enclosure Material Bayblend - 50% ABS and 50% Polycarbonate,
Flame Retardant
UV Stabilized
Mounting Bracket Powder Coated 70 microns
Weight 4 Kg
Colour Electric Orange
Tripping Force 15Nm
Enclosure IP Rating IP66
Dimensions 170mm x 300mmx 125 (HXWXD)
Mounting M12 – Center 245mm
Environmental
Operating Temperature -10 to +60 Degrees Celsius
User Interface
Signal Descriptions
Functional Specifications
The SCANBELT Intelligent Pull key provides two robust mechanically interlinked
contacts ensuring fail safe operation
Audio sirens generate a 105db audio tone indicating impending conveyor start up
When integrated into SCANBELT ISLR2 conveyor belt monitoring system, device
provides visual trip indication via two super bright LEDs mounted on either side of the
device. An alternating beep provides audio feedback
Device address is set via two rotary switches. Supports up to 99 devices in a network
Wiring Diagram
Installation
Product Agreement
Electrotron cc reserves the right to make changes without further notice to any products herein.
The use of the Intelligent Pullkey indicates your understanding and acceptance of the following terms and conditions. This
agreement shall supersede any verbal or prior verbal or written, statement or agreement to the contrary. If you do not understand or
accept these terms, or your local regulations prohibit "after sale" product agreements or limited disclaimers, you must cease and
desist using this product immediately.
This product is © Copyright 2011-202015 by Electrotron cc, all rights reserved. International copyright laws, international treaties
and all other applicable national or international laws protect this product. This product and documentation may not, in whole or in
part, be copied, translated, or reduced to any electronic medium or machine readable form, without prior consent in writing, from
Electrotron cc and according to all applicable laws.
LIABILITY DISCLAIMER
Electrotron cc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose,
nor does
Electrotron cc assumes any liability arising out of the application or use of any product or circuit, and specifically disclaims any
and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in
the data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typical” must be validated for each customer application by customer’s technical experts.
Electrotron cc does not convey any license under its patent rights nor the rights of others. Electrotron cc products are not designed,
intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended
to support or sustain life, or for any other application in which the failure of the Blue Pointer trading 239 (PTY) LTD product could
create a situation where personal injury or death may occur. Should the customer use Electrotron cc products for any such
unintended or unauthorized application, the customer shall indemnify and hold Electrotron cc and its officers, employees,
subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that was negligent regarding the design or manufacture of the part. SCANBELT HECU is a registered trademark of
Electrotron cc. Electrotron cc does not assume liability for the use of this product beyond the original purchase price of the
product.
RESTRICTIONS
You may not use, copy or modify any documentation as expressly defined in this agreement. You may not attempt to unlock or
bypass any authentication algorithm utilized by the product. You may not remove or modify any copyright notice or the method by
which it may be invoked.
All other rights and restrictions not specifically granted in this agreement are reserved by Electrotron cc.
Contact Information
Electrotron cc
3A Slegtkamp Street
Middelburg
1050
Tel: 0132462655
Fax: 0866896603
Email: sales@elt-za.co.za
Web : www.elt-za.co.za
Ordering Information